GENUINE PARTS INSTALLATION INSTRUCTIONS CAUTION
Contents
1. Column cover lower Screws reuse 9 Removal of finisher a Remove bolt 1 on each side and metal clips 2 on each side that attach the existing finisher to the front bumper lower See Fig 3 View b CAUTION e Do not remove the metal clips from the front bumper lower NOTE e Clips require patience Use three inch or longer needle nose pliers 10 Installation of right and left fog lamps a Align 2 ribs on the side of the fog lamp A with the guide located on the bracket B Secure with bolt C from bottom See Fig 4 1 Tightening torque of bolt C FJ 5 5 N m b Install the bracket B which installed the fog lamp A in the metal clip of the front bumper lower It locks with bolt See Fig 4 2 11 Removal of steering column cover a Rotate steering wheel clockwise to access RH screw Remove RH screw Rotate steering wheel counter clockwise to access LH screw Remove LH screw Remove steering column cover upper and partially detach lower cover See Fig 5 View Page 3 of 6 B61E0 1KMOx II Rev 03 08 2010 INSTALLATION INSTRUCTIONS Fog Lamp Kit INSTALLATION PROCEDURE 12 Replacement of combination switch E ENV AG a Remove the Screws which secure the Combination Switch C IF wi Bonn existing combination switch NE jy a b Lift the combination switch upward and remove the connector c Connect the connector to the combination switch C Secure switch to the steering co2. 4 locations Clip position 3 Claw position Fig 1 View a behind the fender protector Clip 1 reuse 1 reuse Bolts 2 reuse Clips 3 reuse Bolts 2 reuse View a Clip reuse Bolt reuse Fender protector Front bumper lower Front bumper upper VY Tab position 10 locations Front bumper lower Section view of tab Push down the tab putting hand from behind E E E 8 Page 2 of 6 Removal of front bumper lower a Turn steering wheel counter clockwise fully b Remove clip 1 on each side from fillet molding of wheel house c Remove 4 claws and 2clips which secure the fillet molding d Front side of the fillet molding is raised See Fig 1 1 4s CAUTION e Do not peel off fillet molding beyond yellow clip e Remove clip 3 locations reuse and bolt 2 on each side reuse that attaches in the front bumper See Fig 1 f Peel off the fender protector it removes bolt reuse and the clip reuse which lock the front bumper lower See Fig 1 2 View a g Remove the tabs engaging the front bumper upper and the front bumper lower then remove the front bumper lower at 10 locations See Fig 2 46 CAUTION e Take care not to damage the removed tabs which will be reused B61E0 1KMOx II Rev 03 08 2010 INSTALLATION INSTRUCTIONS Fog Lamp Kit INSTALLATION PROCEDURE Metal clips Needle nose pliers Bracket B Column cover upper
3. Connect the negative terminal of the battery 18 Ensure that the fog lamp comes on The fog lamp comes on only when the headlamp is set to the low beam At other positions the fog lamp will not come on NOTE e The fog lamp will not come on when the fog lamp SW only is turned ON optional process only if necessary 19 Perform the photometric axis adjustment see Fig 8 by turning the screw located under the lamp using a Phillips screwdriver as shown in Fig 9 1 20 Ensure that the electric equipment such as the small lamp headlamp and turn signal lamp functions properly fe CAUTION e Be sure to check to see if the small lamp headlamp and turn signal lamp function properly B61E0 1KMOx II Rev 03 08 2010 INSTALLATION INSTRUCTIONS Fog Lamp Kit CHECK AFTER INSTALLATION 1 Please check that the installation has no problem C a Confirm connection of connector is secure C b Confirm whether wire harness is fixed C c Confirm no part moving which will cause rattling noise C d Confirm harness is protected from damage by sharp bracket edges FUNCTION CHECK C 1 Re connect battery negative terminal C 2 When auto light is not provided With the low beam of the headlamp being illuminated the fog lamp comes on when the fog lamp SW ON is selected C 3 When auto light is provided With the lighting switch set to AUTO position and the low beam of the headlamp being illuminated the fog lamp comes on
4. when the fog lamp SW ON is selected REINSTALLATION OF REMOVED PARTS C 1 All removed vehicle parts have been reinstalled CAUTION e Use caution when re installing vehicle parts to avoid damage scratch or breaking of mounting clips C 2 Clean interior of vehicle VEHICLE CHECK 1 Remove all tools from the vehicle 2 Inspect reinstalled vehicle parts for proper panel fit 3 Turn ignition to ON position 4 Reset radio presets to the recorded setting 5 Confirm proper radio operation 6 Initialize sun roof and power window operation 7 Turn ignition to off position OOOOOOO CAUTION e During reinstallation please use caution so as not to cause the stacking or pinching of the vehicle s harness or damage any parts Page 6 of 6 B61E0 1KMOx II Rev 03 08 2010
5. GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION Fog Lamp Kit APPLICATION Juke 2011 PART NUMBER Fog Lamp Kit with auto light B61E0 1KMOA Fog Lamp Kit without auto light B61E0 1KMOB KIT CONTENTS Ttem QTY Description Application Service Part Number A 2 ogam 2615089 B i71 Bracket Rm 2690 5 KAA _ e z ot ooo U T osoon _ EA A hn E 1 instalation Instruction Replacement Template TOOLS REQUIRED e Clip clamp tool i ae e Torque wrench e Socket wrench 8mm 10mm e Phillips screwdriver e Needle nose pliers e Masking tape PRE INSTALLATION CAUTIONS NOTES A CAUTION e Care must be taken not to scratch or damage any components during the removal or replacement process NOTE e Dealer Installation Recommended Instructions refer to Service Manual e Use caution when removing trim parts to avoid breaking clips 1 Apply Parking Brake 2 Make sure the shift lever is engaged in P or N position 3 Record customer Radio Presets 4 Use seat and floor protection 5 Open the hood of the vehicle 6 Disconnect the negative battery terminal to prevent short circuits during installation 7 This part is to be installed at a vehicle body surface temperature of 65 100 F Page 1 of 6 B61E0 1KMOx II Rev 03 08 2010 INSTALLATION INSTRUCTIONS Fog Lamp Kit INSTALLATION PROCEDURE Yellow Clip Fig 1 1 Fillet molding Clips 2 Clip reuse Claws
6. lumn Using the two screws which were removed in the step 5a See Fig 6 View d Screws reuse 13 Install the steering column cover Front bumper upper Taped pre wire Fig 7 14 Release right and left pre wired vehicle fog light harness a Pull harness to break the tape See Fig 7 Protection 15 Connect the connector a The protection tapes stick to bumper fascia See Fig 7 b Set front bumper lower to position shown in Front bumper gez Taped pre wire c Connect the vehicle fog lamp harness Fog lamp A Fog lamp A connector to the fog lamp A right and Connector left See Fig 7 View e d Remove the protection tapes to bumper Connector fascia View e Front bumper lower Fog lamp A 16 Install the front bumper lower a Reinstall front bumper lower bolts and clips that labeled reuse using the reverse of the removal process b Install the fillet molding to the original positions Using the original bolts and clips Front bumper Bee ride upper Front bumper VY Tab position 10 locations lower Page 4 of 6 B61E0 1KMOx II Rev 03 08 2010 INSTALLATION INSTRUCTIONS Fog Lamp Kit INSTALLATION PROCEDURE h height of center of lamp body Actually measured height Lamp Bulb Center line h illi j 4 Cut off line Screen Phillips screwdriver upper line Screen Height of center of lamp body Illuminated Flat surface Downward Upward Page 5 of 6 17
Download Pdf Manuals
Related Search