Home

Instructions

1. blue trace coil wire inside the harness on all models other than 2011 Softails On 2011 Softail models the front coil ___ wire is green with a blue JS _ z tracer and the rear coil wire LPIC 5 j i is gray with a blue tracer ar 4A PIC 8 WIRE HARNESS U UNDER SEAT Tes i Note Refer to an H D electrical j diagnostic manual to verify the correct wire colors for your motorcycle CHASING LED TIMING COVER INSTALLATION STEP 8 Kuryakyn Place the T Tap connector over the front or rear coil wire and close ensuring that the tab is engaged PIC 6 7 amp 8 ATTENTION Kiryakyn recommends the use of dielectric grease on electrical connections STEP 9 NOTE Picture 8 is for 2011 Softails only Picture 7 is STEP 10 STEP 11 NOTE Use the included Y Adapter harness if using multiple seven color chasing STEP 12 ATTENTION Secure all wiring away from any moving parts pinch points or STEP 13 Insert the purple wire from the control switch into the male Scotch Lock and crimp making sure that ALENE the wire is secure for all other years and models ew Now hook the purple wire with the male Scotch Lock from the control switch to the T Tap that was installed on the coil wire PIC 7 or PIC 8 Plug the wiring harness from the chasing LED cover into the harness from the switch products on your motorcycle One controller is capable of handling up to four units Secure all wiring away from heat s
2. ICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE A a a elu eer ae ae PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS STEP 1 Read and understand all steps in the instructions before starting the installation Park the motorcycle on a hard level surface and turn off the ignition Let cool ATTENTION A factory service manual may be helpful in performing this installation Do not attempt to perform this installation if you are not confident in your ability to complete all of the steps in the procedure consult a trained technician cont 1302 24HD 0111 WARNING STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7 cont Note The flat plate with five holes is for twin cam motors The beveled plate and Note When installing on Evo or XL motors place the spacer ring against the YOU WILL BE WORKING AROUND THE ENGINE AND EXHAUST SYSTEM DURING INSTALLATION ENSURE THAT THE ENGINE AND EXHAUST SYSTEM HAVE FULLY COOLED TO PREVENT INJURY Kuryakyn BEVELED PLATE AND BEAUTY RING FOR EVO AND SPORTSTERS 4 a gt C a S eS ru ETA E G rak Fe 7 Poon gt si eo me Y s e erR N Remove the fasteners which secure the timing cover the fasteners and cover will no longer be used the spacer ring are for Evo and XL motors PIC 1 Install the appropriate plate using the 8 32 x 3 8 FSCS screws from the hardware kit five if mounti
3. hipaa INSTALLATION PRODUCTS CHASING LED TIMING COVER 1302 PARTS INCLUDED CUSTOMER SERVICE 1 Chasing LED Point Cover Assembly sl ios Coase TETEE 1 Finned Cone ri Te Aag 1 Hardware Kit including 1 Mounting Plate for Twin Cam a LIMITED WARRANTY 1 Mounting Plate for XL and Evo Big Twins ee ta a ee ee 1 Spacer Ring 5 8 32 x 3 8 Flat Socket Cap Screw FSCS 1 10 24 Hex Nut 2 10 SAE flat washers e Kuryakyn shal 1 Dielectric Grease Pack 1 Alcohol Pad 4 4 Nylon cable Ties a 1 Y Adapter 1 Scotch Lock male 1 T Tap Scotch Lock female K 1 Controller Switch 1 Installation Instructions Please read and understand entire instructions before starting installation THANK YOU FOR CHOOSING K RYAKYN IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND OR eKiiryakyn products are often intended foi PROPERTY DAMAGE OR LOSS PLEASE PAY CLOSE ATTENTION TO ALL hares INSTRUCTIONS WARNINGS CAUTIONS AND ATTENTION NOTES REGARDING THE USE AND CARE OF THIS PRODUCT Kir WARNING THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY ATTENTION This indication alerts you to the fact that ignoring the contents Kir described herein may negatively affect product performance and functionality TOOLS SUGGESTED Set of hex wrenches Torx drivers wire stripper crimper combination wrenches or nufact socket set and ratchet ABOUT OUR CATALOG STR
4. ng on a Twin Cam or two if mounting on an XL or Evo PIC 2 Place the LED cover over the stud on the mounting plate be sure to route the wires away from the exhaust engine or any moving parts mounting plate so that it is behind the cover making sure that the timing cover wiring is placed in the notch of the spacer ring Secure the cover using the 10 24 Hex Nut and 10 flat washer PIC 3 Install the finned cone tightening until it clicks several times Wiring Remove the seat and the side panel on touring models A Determine a location on you bike to mount the control switch This location needs to be close enough to the chasing LED cover so that the wiring harness from the cover will reach the wiring harness from the switch and the power 7 wires will reach the battery terminals The black wire from the switch is a ground wire and needs to be secured to the pay WIof negative terminal on the battery W FROM EXHAUST The red wire from the switch with in line fuse is a power wire and needs to be secured to the positive terminal on the battery 1 ROUTE WIRE AWAY TE iw Locate the ignition harness carbureted or the electronic fuel injection harness which is most commonly located under the seat or under the side cover on the right hand side of the motorcycle PIC 4 and PIC 5 Carefully expose the wires located inside the harness cover Locate the front blue with orange trace or rear yellow with
5. ources and or moving parts using the included cable ties Melted wire insulation may result in a short circuit extreme heat K ryakyn WILL NOT warranty any electrical component that fails due to pinched crimped broken abraded Y FA L melted or frayed wires Kee LAE AA S gt Z z A N Sy Yj lt Reinstall the seat and the side panel eal A a SN r N i 4 f Z A ay ATTENTION It is the installer s responsibility to ensure that all of the fasteners including pre assembled are tightened before operation of the motorcycle Kuryakyn will not warranty components lost due to improper installation Periodic maintenance may be required 2011 SOFTAILS MAN ONLY Controller Switch Operation A Xs e Flip the switch to the mode position and press the selector button to choose either the chasing mode or the steady illumination mode ad PE Flip the switch back to the color position and press the selector button to _ P choose the color the color sequence is as follows GRAY WIRE WITH ie Red BLUE TRACER Lime Ice White l Sky Blue Dark Blue Purple Violet Green Paint Mode continuously cycles through all seven colors Flip the switch back to the mode position PAGE Ride On 3 CHASING LED TIMING COVER INSTALLATION

Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents