Service Information
Contents
1. Please order separately A Also available in Repair Kit 6 197 Please order separately 77 2055 R8 2 6 2015 3 4 BINK WARRANTY POLICY Binks products are covered by Finishing Brands one year materials and workmanship limited warranty The use of any parts or accessories from a source other than Finishing Brands will void all warranties For specific warranty information please contact the closest Finishing Brands location listed below Finishing Brands reserves the right to modify equipment specifications without prior notice DeVilbiss Ransburg BGK and Binks are registered trademarks of Carlisle Fluid Technologies Inc dba Finishing Brands 2015 Carlisle Fluid Technologies Inc dba Finishing Brands All rights reserved BINnKS USA Canada www binks com info finishingbrands com Tel 1 800 992 4657 Fax 1 888 246 5732 United Kingdom www finishingbrands eu info finishingbrands eu Tel 44 0 1202 571 111 Fax 44 0 1202 573 488 China www finishingbrands com cn mkt finishingbrands com cn Tel 8621 3373 0108 Fax 8621 3373 0308 BINnKS Mexico www finishingbrands com mx sales finishingbrands com mx Tel 011 52 55 5321 2300 Fax 011 52 55 5310 4790 France www finishingbrands eu info finishingbrands eu Tel 33 0 475 75 27 00 Fax 33 0 475 75 27 59 Japan www ransburg co jp binks devilbiss ransburg co jp Tel 081 45 785 6421 Fax 081 45 785 6517 Binks is part of Finishing Brands2. a global leader in innovative spray finishing technologies For technical assistance or to locate an authorized distributor contact one of our international sales and customer support locations below Brazil www devilbiss com br sales devilbiss com br Tel 55 11 5641 2776 Fax 55 11 5641 1256 Germany www finishingbrands eu info finishingbrands eu Tel 49 0 6074 403 1 Fax 49 0 6074 403 281 Australia www finishingbrands com au sales finishingbrands com au Tel 61 0 2 8525 7555 Fax 61 0 2 8525 7500 Fictions nn 4 CAET commanr 77 2055 R8 2 6 2015
3. as follows A WARNING Hazards or unsafe practices which Hazards or unsafe practices which could result in minor personal injury product or property damage could result in severe personal injury death or substantial property damage A WARNING Read the following warnings before using this equipment READ THE MANUAL Before operating finishing equipment read and understand all safety operation and maintenance information provided in the operation manual Important installation operation or maintenance information PROJECTILE HAZARD You may be injured by venting liquids or gases that are released under pressure or flying debris OPERATOR TRAINING PINCH POINT HAZARD All personnel must be trained before operating finishing Moving parts can crush and cut Pinch points are basically any equipment areas where there are moving parts EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture malfunction or start unexpectedly and result in serious injury STATIC CHARGE Fluid may develop a static charge that must be dissipated through proper grounding of the equipment objects to be sprayed and all other electrically conductive objects in the dispensing area Improper grounding or sparks can cause a hazardous condition and result in LOCK OUT TAG OUT fire explosion or electric shock and other serious injury I Failure to de energize disconnect lock out and tag out all p
4. L 83 2798 OBSOLETE FOR REFERENCE ONLY SPEED The speed of the air motor is regulated by the air adjusting valve part number 73 159 see page 1 The speed of the propeller shaft is determined by the fluid but it should never exceed 3 000 RPM LUBRICATION AIR MOTOR The bearings are pre lubricated and sealed However every 100 hours insert a few drops of SAE 10 non detergent oil into the air inlet to lubricate the vanes and housing surfaces AIR SUPPLY The air supply to the motor should be 60 PSI minimum for best results PARTS LIST When ordering please specify Part No ITEM PART NO NO DESCRIPTION QTY 1 lt OS480 A GASKET irienner ana vin apse 1 2 37 89 ROTOR 83 2798 ssessseessessseesstesees 1 3 37 90 a OM SEAL aeien eiea 1 4 37 91 a BEARING sicsesiccteccssccevseeresncsuasadorsss 2 5 37 92 VANE 83 2798 cccesseeceeseeeeeeaeneeenaeees 4 6 37 93 BODY 83 2798 csccsesseessessseesseessees 1 7 37 96 END CAP eoincecceusvactintvadveiestaevahs i 8 37 337 amp GASKET END CAP sssssssssssrserresrees 2 9 37 412 PLATE DEAD END wees ivsessacnsstaveceseens 1 10 37 413 PLATE DRIVE END wicciceiscsueretececsevin 1 11 37 415 FILLISTER HEAD SCREW scn 12 12 37 482 ROTOR 8322815 wscedescesessavnsucrevecevcas 1 13 37 4844 VANE 83 2815 cccesseeeeeeeeeeeeaeeeeeneeees 4 14 37 1045 BODY 83 2815 wisvesvescisie a ceceativveress 1 Repair Kit Parts for 83 2798 Order 6 183 Also available in Repair Kit 6 183
5. SERVICE MANUAL BINKS MODEL 31 296 1 H P AGITATOR MODEL 31 295 1 2 H P OBSOLETE FOR REFERENCE ONLY A IMPORTANT Read and following all instructions and safety precautions listed on Page 2 before using equipment Retain for future reference DESCRIPTION The air motor is a precision built rotary vane type motor The vanes take up their own wear and will last 5 000 15 000 hours depending upon speed method of oiling operating pressure and the precautions taken in maintaining the motor The type of shaft seal used does not lend itself to operating pressures above 100 psi Allowing excess moisture or foreign particles from the air line to enter the motor will reduce operating life INSTALLATION First install a moisture trap and filter in the air line ahead of motor For efficiency of output and control of speed use air lines or hose the same size as or the next pipe size larger than the intake port of the motor OPERATION The stalled or starting torque is less than the running torque and will vary depending on the position at which the vanes stop in relation to the air intake port Operate motor well below available line pressure so that full line pressure can be called upon for overloads on motor The speed is regulated by the air valve 8 If the duty is continuous or speed is high use an automatic air line oiler set to feed 1 3 drops per minute The bearings will receive oil from the rotor chamber during
6. automatic oiling Use SAE No 10 non detergent oil Lubrication is necessary for the bearings shaft seals and rust prevention Excessive moisture in the air line can cause rust formation in motor and might also cause ice to form on muffler due to expansion of air through the motor The moisture problem can be corrected by installing a moisture separator in the line and also by installing an aftercooler between the compressor and air receiver PARTS LIST When ordering please specify Part No ITEM PART NO NO DESCRIPTION QTY 1 20 1076 SET SCREW ca ccsavvecnexnesesSsteavebucseive 4 2 20 3344 SET SCREW sata M2 Includes Item Nos 3 20 4607 PIN ires asserentes 8 2 3 11 amp 12 4 31 9 COUPLING wicecsscastanaeaceccevecsasesenccsays Al 5 31 291 ADAPTER vvsveesiavisconsecevesteseccreaccserevs 1 6 31 292 SHIAP Wisvivcssscscsevapeectinstecotsegnadestteseve 1 7 57 13 NIPPLE wiiccrsisdoax scccatwanagertesnetcaeseanecate at 8 73 159 AIR VALVE seisciatancavesses cismases can cccietavs 1 9 83 1527 MUFRVER wiccicscesetssstectadeaevsecadesesteas 1 10 83 2815 AIR MOTOR 1 H P 31 296 cscssssseseers 1 83 2798 AIR MOTOR 1 2 H P 31 295 sassen 11 149 844 BIEADES itrenn a 8 12 149 847 AUB raene 2 13 149 851 PADDLE ASSEMBLY seseseseeeeeees 2 Obsolete for reference only 77 2055 R8 2 6 2015 1 4 BINK In this part sheet the words WARNING CAUTION and NOTE are used to emphasize important safety information
7. ower sources before performing equipment maintenance could cause serious injury or death WEAR RESPIRATOR Toxic fumes can cause serious injury or death if inhaled Wear a respirator as recommended by the fluid and solvent AUTOMATIC EQUIPMENT manufacturer s Material Safety Data Sheet Automatic equipment may start suddenly without warning TOXIC FLUID amp FUMES Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin inhaled injected or swallowed LEARN and KNOW the specific hazards or the fluids you are using FIRE AND EXPLOSION HAZARD Improper equipment grounding poor ventilation open flame or sparks can cause a hazardous condition and result in fire or explosion and serious injury PRESSURE RELIEF PROCEDURE Always follow the pressure relief procedure in the equipment instruction manual KEEP EQUIPMENT GUARDS IN PLACE Do not operate the equipment if the safety devices have been removed MEDICAL ALERT Any injury caused by high pressure liquid can be serious If you are injured or even suspect an injury e Go to an emergency room immediately e Tell the doctor you suspect an injection injury e Show the doctor this medical information or the medical alert card provided with your airless spray equipment e Tell the doctor what kind of fluid you were spraying or dispensing KNOW WHERE AND HOW TO SHUT OFF THE EQUIPMENT IN CASE OF AN EMERGENCY WEAR SAFETY GLASSES Failu
8. re to wear safety glasses with side shields could result in serious eye injury or blindness GET IMMEDIATE MEDICAL ATTENTION To prevent contact with the fluid please note the following e Never point the gun valve at anyone or any part of the body e Never put hand or fingers over the spray tip INSPECT THE EQUIPMENT DAILY Inspect the equipment for worn or broken parts on a daily basis Do not operate the equipment if you are uncertain about its eho se condition e Never attempt to stop or deflect fluid leaks with your hand NEVER MODIFY THE EQUIPMENT pody glove ar Ted l Do not modify the equipment unless the manufacturer provides e Always have the tip guard on the spray gun before spraying written approval e Always ensure that the gun trigger safety operates before spraying NOISE HAZARD PROP 65 WARNING You may be injured by loud noise Hearing protection may be CA PROP WARNING This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm required when using this equipment i Ul IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE OPERATOR OF THE EQUIPMENT FOR FURTHER SAFETY INFORMATION REGARDING THIS EQUIPMENT SEE THE GENERAL EQUIPMENT SAFETY BOOKLET 77 5300 Binks reserves the right to modify equipment specification without prior notice BINK 2 4 77 2055 R8 2 6 2015 Binks MODEL 83 2815 AIR MOTOR ASSEMBLY MODE
Download Pdf Manuals
Related Search