B.A.S.I.S. Locks Backup Battery Replacement Kit Instructions
Contents
1. For instructions see the B A S I S G Service Manual 163300 or the B A S I S V Service Manual 161805 B Remove old escutcheon gasket and backup battery Caution Before you handle the electronics board or any component connected to it make sure that you are properly grounded using an electrostatic discharge ESD protection kit Touching the board without proper grounding can damage sensitive electronics components even if you don t notice any static discharge 1 Unscrew the six mounting plate standoffs from the mounting plate Figure 3 2 Remove the gasket from the escutcheon and discard the gasket 3 Remove the lift finger a Note the orientation of the lift finger b Remove the lift finger screw and discard c Remove the washer and lift finger 4 Remove the mounting plate Figure 4 a Cut the cable tie and discard b Remove the five screws and discard c Carefully remove the mounting plate 5 Remove the backup battery from the battery socket plate Figure 1 D o 28 Mounting pl 72 ounting plate ZB screws Figure4 Removing and reinstalling the mounting plate 2 BEST ACCESS SYSTEMS Indianapolis Indiana B A S 1 S Locks Backup Battery Replacement Kit Instructions D Install new backup battery and escutcheon gasket Slide the new backup battery under the clip and into position in the battery socket Figure 5 Slide the new escutcheon gasket onto the upper escutcheon post Press the gasket into place o2. S I S G Service Manual or the B A S 1 S V Service Manual LEDs Sounder You should Single Use the card at a moderate speed red flash Red 3 short Use the temporary operator card flashes tones provided with the lock Green Check the motor connection flashes Check the battery connection For locks with key override Insert and turn the key to unlatch the door For locks with deadbolt From the inside of the door turn the turn knob and make sure that the deadbolt operates properly Indianapolis Indiana T61821 Rev A 1847699 ER 7991 12 Oct 2002 2001 2002 Best Lock Corp dba Best Access Systems
3. return springs B A S 1 S Locks Backup Battery Replacement Kit Instructions Tasks to perform for all B A S LS locks and EX Series Exit Hardware Trim E Test lock for proper operation To test the lock for proper operation before the lock is programmed use the temporary operator card that came with the lock This card is for temporary use only After permanent cards have been programmed for the lock the temporary card should be deleted 1 Use the temporary operator card to activate the lock When the lock detects the presence of a card for the first time the lock performs a series of diagnostic self tests If no problem is detected the lock responds with 4 red LED flashes simultaneous with 4 green LED flashes and 4 short tones If a problem is detected the lock s red LED and green LED simultaneously flash in a repeating pattern and no tones sound The lock s control electronics board must be replaced For instructions see the B A S I S G Service Manual or the B A 5 1 S V Service Manual Note f the lock has a proximity card reader it may have already been activated by the presence of an object near the card reader 2 Use the temporary operator card to access the lock The green light flashes and the locking mechanism unlocks 3 Turn the lever and open the door BEST ACCESS SYSTEMS If the mechanism doesn t unlock refer to the following table For additional troubleshooting instructions see the B A
4. B A S 1 S Locks a AH 3 Si Backup Battery pF lt cESS systems Replacement Kit Instructions Overview These instructions describe how to replace the backup battery in your B A S I S Mortise Lock 35HG or 35HBV Cylindrical Lock 93KG 95KG or 93KBV 95KBV or Exit Hardware Trim EXG or EXBV Components checklist In addition to these instructions this kit part number 1833843 contains Q 1 Backup battery Q 2 Outside escutcheon gaskets one for mortise or cylindrical locks and one for exit hardware trim EHT Q 5 Screws used only for EHT Q 1 Lift finger screw used only for EHT Tasks to perform for cylindrical or mortise electronic locks Note For tasks to perform on EX Series exit hardware trim see page 2 A Remove inside and outside escutcheons from door For instructions see the B A S I S G Service Manual T63300 or the B A S I S V Service Manual T61805 B Remove old escutcheon gasket and backup battery Caution Before you handle the electronics board or any component connected to it make sure that you are properly grounded using an electrostatic discharge ESD protection kit Touching the board without proper grounding can damage sensitive electronics components even if you don t notice any static discharge 1 Remove the gasket from the outside escutcheon and discard the gasket 2 Remove the backup battery from the battery socket C Install new backup battery and escutcheon
5. gasket 1 Slide the new backup battery under the clip and into position in the battery socket Battery socket f Lift the battery here Th a Figure1 Removing the backup battery ATT AAT TT TTT Battery clip Battery scat hy T TOOT Backup battery Slide the backup battery under the clip Figure 2 Installing the backup battery BEST ACCESS SYSTEMS Indianapolis Indiana B A S 1 S Locks Backup Battery Replacement Kit Instructions xy Mounting standoffs Escutcheon gasket Screw Toe Lift finger a 2 Mounting standoffs Figure3 Removing and reinstalling the mounting standoffs gasket and lift finger Primary harness Cable tie 0 Mounting plate screws o o _ amp o N Mounting 2 Slide the new escutcheon gasket onto the upper escutcheon post Press the gasket into place on the edge of the escutcheon so the electronics board is covered D Reinstall inside and outside escutcheons on door For instructions see the B A S I S G Service Manual or the B A S 1 S V Service Manual Note Skip to page 4 Test lock for proper operation Tasks to perform for EX Series Exit Hardware Trim A Remove the escutcheon from door
6. n the edge of the escutcheon so the electronics board is covered With posts on the mounting plate inserted in the lever return springs slide the mounting plate into the escutcheon Figure 6 Make sure that the locking plate fits into the slot in the mounting plate Secure with the five new screws Route the primary harness against the mounting plate post and secure the harness to the post with a cable tie See Figure 4 Position the lift finger on the escutcheon in the orientation noted in step 3a on page 2 Position the washer on the lift finger screw Tightly secure the lift finger with the lift finger screw 25 30 foot pounds of torque Figure 3 Starting at the bottom of the gasket peel away the protective backing a small amount at a time while unrolling the gasket into position on the escutcheon Press the gasket into place Screw the six mounting standoffs onto the mounting plate Figure 3 Reinstall the escutcheon on door For instructions see the B A S I S G Service Manual or the B A S 1S V Service Manual r Battery clip Battery P E Slide the backup battery under the clip Backup battery P CK y BEST ACCESS SYSTEMS Indianapolis Indiana Figure 5 Installing the backup battery Lever return springs Figure6 Removing and reinstalling lever
Download Pdf Manuals
Related Search