2004 altima and sentra with qr25de engine crank
Contents
1. 00 CONSULT II TP030629 Figure 6 9 Select Transfer files via LAN see Figure 7 NOTE If you accidentally choose a menu option other than Transfer Files via LAN turn CONSULT II OFF and then back ON as shown in Figure 6 above CHI OOO c CONSULT II a TP000592 7 Set the CONSULT II unit down for now and go to your ASIST PC 10 25 10 Transfer download data from ASIST into CONSULT II A On the ASIST screen click on Transfer see Figure 8 Insert reprogrammng card 2 Pieca ame ele 3 Release finger 4 Select Transfer Connect A C power adapter ingar on sorcen from screen file Via LAN Connect Ethernet cable to while processing UP after 2 tone beep CONSULT II amp PC port Click TRANSFER Ww ji es e ee TP030623 Figure 8 e Data transfer will take about 15 seconds e Transfer progress is displayed on the ASIST screen see Figure 8 B Wait until the data transfer is complete see CAUTION below CAUTION DO NOT DISCONNECT THE ETHERNET CABLE UNTIL COMPLETE IS DISPLAYED AS SHOWN IN FIGURE 9 ON THE NEXT PAGE e lf the cable is disconnected before Complete is displayed you MUST restart the transfer download procedure otherwise ECM damage can occur e If the cable is disconnected during the transfer wait for ASIST to display an error message then click on OK Select Backup then2. a J44200 40 K HF An Pigtail Converter Cable T PN J44200 20 7 Velcro sirap TP020328a Figure 10 CAUTION e Nissan requires the use of essential tools shown in Figure 10 when performing ECM reprogramming e J44200 10 Pigtail should not be removed from the CONSULT II DDL Port This Pigtail allows use of the stronger quick disconnect cable set e lf cables are very often changed at the DDL Port base of the CONSULT II unit cable connector pin damage may result e lf there is connector pin damage ECM reprogramming may fail Permanent ECU damage can occur NISSAN 15 Turn ON the ignition switch do not ELECTRONIC CONTHOLUNIT start the engine REPROGRAMMING e CONSULT II will turn ON AERO2C 1 automatically see Figure 11 INITIATE ECU REPROGRAM e Confirm that all electrical loads except for the ignition are OFF SUB MODE Headlights defroster A C Audio LIGHT Copy radio and cellular telephone etc TP030620 Figure 11 14 25 16 Roll down the driver s window part way exit the vehicle close the door and hang the CONSULT II unit on the outside of the window see Figure 12 e This step is necessary to ensure the CONSULT II and DLC II cable will not be disturbed during reprogramming CAUTION DO NOT connect the same CONSULT II AC power supply for St
3. 23710 8Y102 A34 VQ35 ES To 23710 8Y 112 VQ35 4A T ASCD TCS ndi Sa 3 5 Speed A T Models T E EEE Number a m To 23710 7Y002 VQ35 6M T ASCD Pathfinde 1 File s selected Search by Code el per bulletin only Kaypa EES aes A eae This illustration is for example only your vehicle may be different ei Figure 5 A Seleci vehicle model and model year B Select the correct reprogramming data 1 Locate the specific Model Configuration Example QR25 A T ASCD NOTE e Model Configuration may include items like engine type transmission type and vehicle options such as ASCD TCS ABS etc e Vehicle configuration can be verified using the Current ECM P N in Chart A on page 5 2 Select click on the To number NOTE The To number reads 23710 XXXXX 3 Write the To number on the Repair Order You will need it later in the reprogramming process C Click on the Add button to add data to the File s selected list This list is on the right side of the screen D Click the CONTINUE button to proceed with CONSULT II setup 9 25 Fress and hold ee p thumb on 8 Turn ON CONSULT II as shown in CONSULT II screen Figure 6 Quickly press then release the On Off switch After double beep sounds release thumb from screen
4. The DLC II does not have a good connection to the vehicle not straight The DLC II cable may have a malfunction damaged wire or pins The CONSULT II Converter J44200 50 black box is not working correctly see Figure 10 on page 14 16 25 Section 3 ECM Reprogramming 20 Press INITIATE ECU REPROGRAM see Figure 14 then A Press ECM B Review the precaution C Press NEXT NISSAN SELECT TARGET ECU PRECAUTION lt PRECAUTION gt ELECTRONIC CONTROL UNIT 1 Make sure vehicle battery is properly REPROGRAMMING charged h 2 Make sure all vehicle accessories are OFF 3 Connect AC DC power supply to AERO2C 1 CONSULT II If CONSULT II battery is properly charged this can be omitted lt REPROGRAMMING gt 4 Execute ECU reprogram based on INITIATE ECU REPROGRAM operation manual S 5 Touch START the back light will turn off automatically and reprogramming will begin TP030627 Figure 14 ECM REPROGRAMMING NOTE 21 Press CHECK ECM P N to confirm ase ei These numbers take note of the current ECM part PART are only examples NUMBER 23710 3Y116 number see Figure 15 Your numbers 13Y116 will differ 03FA5DCC CALIBRATION ID NOTE This is the vehicle s ECM part number BEFORE Reprogramming TP030630 Figure 15 22 Press COPY to print the current ECM part numb
5. 8U522 23710 8U52B B15 8U523 8U52A with 23710 8U540 8U541 8U542 23710 8U54B QR25 A T with NATS 8U543 8U54A engine l 23710 8U560 8U561 8U562 23710 8U56B 5 M T with NATS 8U563 BUS6A 23710 8U570 8U571 8U572 23710 8U57B 6 M T with NATS 8U573 BUS7A 23710 8U740 8U741 8U742 23710 8U98A FED A T 8U743 23710 8U78A 23710 8U78B 2004 CAL A T 23710 8U860 8U861 8U862 23710 8U86A 23710 8U745 8U746 8U747 23710 8U99A FED A T with NATS 8U748 23710 8U79A 23710 8U79B A T with NATS CAL 23710 8U865 8U866 8U867 23710 8U89A 6 M T with NATS 23710 8U905 8U906 8U907 23710 8U90A 6 M T 23710 8U900 8U901 8U902 23710 8U92A NOTE e Part numbers for ECM programs are subject to change e lf amore recent part number is available for any of the ECM data specified in the Chart above the latest version should be used to complete this campaign repair e ASIST contains the latest version of all ECM data 20 25 28 Press END to return to the main menu 29 Turn the ignition switch OFF and CONSULT II OFF 30 Wait more than 10 seconds then turn the ignition switch ON for 1 second Then turn the ignition switch OFF again for 10 seconds see Figure 20 e This will reset ECM self learned Data Ignition key ON About 1 Sec About 1 Sec Ignition key OFF 10 Sec 10 Sec TP030626 Figure 20 Section 4 Perform ECM Reprogram Confirmatio
6. VOL LEARN Start the engine and let the idle stabilize for about 30 seconds Touch START and wait 20 seconds to 2 minutes CMPLT should be displayed NOTE If INCMP is displayed within 2 minutes or test is not finished within 2 minutes Idle Air Volume Learning was not carried out successfully Make sure you set all of the preconditions exactly as shown in the chart above and performed steps 1 through 6 exactly as shown Rev up the engine two or three times and allow it to return to idle NOTE For additional IAVL procedure details refer to the Service Manual 22 25 PROGRAMMING UNEXPECTEDLY TERMINATED See step 27 on page 19 e The ECM has been permanently damaged and will require replacement e Perform steps A through G below CAUTION Do not start the engine with the damaged ECM installed A Turn the ignition OFF turn CONSULT II OFF and DISCONNECT THE NEGATIVE TERMINAL OF THE VEHICLE BATTERY B Attach the CONSULT II print out to the repair order for future reference C Replace the damaged ECM D Reconnect the negative battery cable E If the vehicle is equipped with NATS e Some models will require registration of the NATS keys e See the appropriate TSB s or Service Manual ESM for NATS information and key registration procedures F Perform IAVL Idle Air Volume Learning on page 22 G Check the new ECM s current P N make sure it is the latest newest P N
7. at low speed IDENTIFICATION NUMBER Nissan has assigned identification number R0606 to this campaign This number must appear on all communications and documentation of any nature dealing with this campaign NUMBER OF VEHICLES POTENTIALLY AFFECTED The number of vehicles potentially affected is approximately 296 948 1 25 DEALER RESPONSIBILITY It is the dealers responsibility to check Service Comm for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department This includes vehicles purchased from private parties or presented by transient tourist owners and vehicles in a dealer s inventory Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration While federal law applies only to new vehicles Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed 2 25 REPAIR OVERVIEW Use Service Comm campaign ID R0606 to confirm the vehicle you re working on is affected by this campaign Use CONSULT II to make sure there are no DTCs stored in the ECM e Repairs for DTCs must be done before performing the ECM reprogramming e Repairs for stored DTCs are not related to this campaign Check the current ECM P N Current ECM P N
8. see step 21 on page 17 NOTE e Anew ECM from the parts department may not have the newest program e f needed return to step 5 on page 8 of this procedure and reprogram the new ECM with the latest available P N Be careful to follow each step exactly as written 23 25 CLAIMS INFORMATION Submit a Campaign CM line claim using the following claims coding CM I D R0606 DESCRIPTION OP CODE FRT Reprogram ECM and perform Idle Air R06061 Volume Learning Procedure 24 25 OWNER S LETTER Dear Nissan owner This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act Nissan has decided that a defect which relates to motor vehicle safety exists in some 2003 2004 model year Nissan Altima and Sentra vehicles equipped with the 2 5 liter engine Our records indicate that you own the Nissan vehicle identified by the Vehicle Identification Number on the cover of this notice Reason for Recall On some 2003 2004 model year Nissan Altima and Sentra vehicles equipped with the 2 5 liter engine there is a possibility that the engine might stop running while being driven due to an electrical problem between the crank angle sensor and the Electronic Control Module engine computer This may also result in the Service Engine Soon light coming on If the engine stops running while driving this could result in a crash without warning What Nissan Will Do In order
9. should match one in Chart A on page 5 Perform ECM Reprogramming Perform IAVL Procedure 3 25 SERVICE PROCEDURE Before beginning this Service Procedure use CONSULT II to make sure there are no DTCs stored in the ECM Repairs for stored DTCs must be done before performing the ECM reprogramming Use ASIST for DTC diagnostic and repair information Repairs for stored DTCs are not related to this campaign Check the Current ECM Part Number P N 1 With the Diagnostic Card red white card in CONSULT II and CONSULT II turned ON print the ECM Part Number as follows START Nissan gt gt gt gt ECM PART NUMBER gt gt COPY 2 Attach this printout to the Repair Order e Figure A is an example of the ECM Part 23710 XXXXX Number printout CALIBID ECM XXXXX Figure A TP050001 3 Using the ECM P N printout e Compare your vehicle s ECM P N to those shown under Current ECM P N in Chart A on the next page 4 25 Chart A From To 4 s 4 Current ECM P Ns New MODEL YEAR Vehicle Configuration Before Reprogramming ECM PIN s i 23710 9J000 9J001 9J002 23710 9J00B ALT AEDS ED 9J003 9J004 9J00A 2003 ae 23710 9J005 9J006 9J007 23710 9J03B 9J008 9J009 9J03A 23710 9J010 9J011 9J012 23710 9J01B Altima M T with ASCD 9J013 9J014 9J01A L31 MT 23710 94015 9J016 9J017 23710 9J04
10. the Ethernet card connection port 4 Confirm the CONSULT II date and time are correctly set as follows This is necessary to provide a valid print out for warranty claims A With the Reprogramming card in slot A turn ON CONSULT II B Touch SUB MODE 6 25 C Touch SET DATE see Figure 2 1 If the date is not correct touch the MONTH DAY or YEAR as needed Then adjust it by using arrow keys Once done press SAVE press BACK and go to step D 2 If the date is OK press BACK and go to step D SUB MODE VERSION CONFIGURE ETHERNET COMMUNICATIONS TEST LCD TEST P com BACK LIGHT COPY Figure 2 TP030628 D Touch SET TIME see Figure 2 1 If time is not correct touch the HOUR MINUTE or AM PM as needed Then adjust it by using arrow keys Once done press SAVE press BACK and go to step 5 2 If time is OK press BACK and go to step 5 IMPORTANT NOTE e lf your ASIST PC is already being used to perform ECM Reprogramming proceed to step 5 on the next page e If you are unsure whether your ASIST PC has already been set up for ECM Reprogramming look in ASIST under CONSULT Utilities CONSULT II Info NISSAN ECU Reprogramming This will give you instructions for setting the Ethernet IP Address of the ASIS
11. to prevent this incident from occurring your Nissan dealer will reprogram the Electronic Control Module This free service should take about one hour to complete but your Nissan dealer may require your vehicle for a longer period of time based upon their work schedule or parts availability What You Should Do Contact your Nissan dealer at your earliest convenience in order to arrange an appointment to have your vehicle repaired If the Service Engine Soon light comes on contact your dealer as soon as possible to have your vehicle inspected Please bring this notice with you when you keep your service appointment Instructions have been sent to your Nissan dealer If the dealer fails or is unable to make the necessary repairs free of charge you may contact the National Consumer Affairs Department Nissan North America Inc P O Box 685003 Franklin TN 37068 5003 The toll free number is 1 800 NISSAN1 1 800 647 7261 You may also contact the Administrator National Highway Traffic Safety Administration 400 Seventh Street SW Washington DC 20590 or call the toll free Vehicle Safety Hotline at 1 888 327 4236 TTY 1 800 424 9153 or go to http www safercar gov If you have paid to have a crank position sensor replaced prior to this campaign you may be eligible for reimbursement of the related expense Contact Nissan Consumer Affairs at the numbers listed above for additional information on how to obtain a reimbursement Feder
12. 3 Do not start the engine with the damaged ECM installed 19 25 This chart is provided as a reference to confirm the correct final ECM P N after reprogramming From To R ECM P Ns Final New MODEL YEAR Vehicle Configuration Before Reproarammin ECM PIN s l 23710 9J000 9J001 9J002 23710 9J00B A T with ASCD 9J003 9J004 9J00A 2003 re 23710 9J005 9J006 9J007 23710 9J03B 9J008 9J009 9J03A 23710 9J010 9J011 9J012 23710 9J01B Altima M T with ASCD 9J013 9J014 9J01A L31 MT 23710 9J015 9J016 9J017 23710 9J04B with 9J018 9J019 9J04A QR25 50 state A T with ASCD 23710 9J31B angine ULEV 23710 93305 9J306 9J307 9J31A CAL A T with ASCD 23710 93360 9J361 9J35A 23710 9J35C SULEV 9J35B 2004 50 state A T ULEV 23710 94800 9J301 9J302 9J30A 23710 9J30B A T CAL SULEV 23710 93320 9J321 9J34A 9J34B 23710 9J34C posale ene ASCD 53710 9 315 9J316 9J317 qU33A 29710 9J33B CAL M T with ASCD 23710 9J370 9J371 9J37A 23710 9J37C SULEV 9J37B 50 state MT ULEV 23710 93310 9J311 9J312 9J32A 23710 9J32B CAL MIT SULEV a 9J365 9J366 9J36A 23710 9J36C a 23710 8U500 8U501 8U502 23710 8U50B 8U503 8U50A Shir 23710 8U510 8U511 8U512 23710 8U51B 8U513 8U51A Sentra 2003 hie 23710 8U520 8U521
13. 907 23710 8U90A 6 M T 23710 8U900 8U901 8U902 23710 8U92A A lf your vehicle s ECM P N matches one of the Current ECM P N s in the chart above Go to Reprogramming the ECM next page B If your vehicle s ECM P N does not match one of the Current ECM P N s in the chart above e This campaign may not apply or has already been done on this vehicle e Recheck Service Comm campaign ID R0606 to confirm the vehicle you re working on is affected by this campaign 5 25 REPROGRAMMING THE ECM Reprogramming should be performed by an OBDII Certified technician The reprogramming procedure involves three general steps e Setting up e Download transfer data from ASIST into CONSULT II e Download new data from CONSULT II into the vehicle Reprogram the ECM SETTING UP Insert card into slot A top F 1 Install the Reprogramming Card into CONSULT II e Make sure CONSULT II is disconnected from the vehicle and turned OFF e The Reprogramming Software Card is the orange Card e Use slot Atop slot see Figure 1 UN Make sure card is fully seated TP010647 Figure 1 2 Connect the AC power supply to CONSULT II 3 Connect CONSULT II to the ASIST PC with the special Ethernet cable P N 02002554 is printed on the cable A Connect one end to CONSULT II at the PC port B Connect the other end to the ASIST PC at
14. B with 9J018 9J019 9J04A QR25 50 state A T with ASCD 23710 9J31B engine ULEV 23710 93305 9J306 9J307 9J31A CAL A T with ASCD 23710 93360 9J361 9J35A 23710 9J35C SULEV 9J35B 2004 50 state A T ULEV 23710 94800 9J301 9J302 9J30A 23710 9J30B A T CAL SULEV 23710 9J320 9J321 9J34A 9J34B 23710 9J34C R UEV ASCD 93710 9315 9 316 0N317 9995A 29710 39338 CAL M T with ASCD 23710 9J370 9J371 9J37A 23710 9J37C SULEV 9J37B 50 state MT ULEV 23710 93310 9J311 9J312 9J32A 23710 9J32B CAL MT SULEV a 91365 9J366 9J36A 23710 9J36C AH 23710 8U500 8U501 8U502 23710 8U50B 8U503 8U50A ie 23710 8U510 8U511 8U512 23710 8U51B 8U513 8U51A Sentra 2003 KAT 23710 8U520 8U521 8U522 23710 8U52B B15 8U523 8U52A with 23710 8U540 8U541 8U542 23710 8U54B QR25 A T with NATS 8U543 8U54A engine 23710 8U560 8U561 8U562 23710 8U56B 5 M T with NATS 8U563 BUS6A l 23710 8U570 8U571 8U572 23710 8U57B 6 M T with NATS 8U573 BUS7A 23710 8U740 8U741 8U742 23710 8U98A FED A T 8U743 23710 8U78A 23710 8U78B 2004 CAL A T 23710 8U860 8U861 8U862 23710 8U86A FED A T with NATS 23710 8U745 8U748 8U746 8U747 23710 8U99A 23710 8U79A 23710 8U79B A T with NATS CAL 23710 8U865 8U866 8U867 23710 8U89A 6 M T with NATS 23710 8U905 8U906 8U
15. T PC and CONSULT II You will need to do this before performing ECM reprogramming 7 25 DOWNLOAD TRANSFER DATA FROM ASIST INTO CONSULT II 5 From the ASIST PC main menu screen select CONSULT UTILITIES see Figure 3 Maxima INFO Altima Reference ode Diagnosis Tool Box SS Sentra Kel Pathfinder oo i ZZ irited eri D SA Mi Xterra Frontier D D 4 More More Ge Tools amp Latest Clai i CONSU tp J Updated PEER campaidigl Utilities amp Upd O O TP030632 Figure 3 6 From the CONSULT UTILITIES E Soas screen select ECM TCM DATA UpAates see Figure 4 23 ECM TCM Tou s Capture EN Data TP030622 Figure 4 8 25 7 Select the ECU REPROGRAMMING DATA see Figure 5 as follows A r 4 ECU Electronic Control Unit ode S R i ae eprogramming Data Configuration GONG ATI prog 9 l Click the Add button 350Z 2904 4 Speed A T Models 2002 em To 23710 8Y102 VQ35 4A T ASCD To
16. Technical Bulletin Sew ne ee ee Reference NTB06 051a November 17 2006 VOLUNTARY RECALL CAMPAIGN 2003 2004 ALTIMA AND SENTRA WITH QR25DE ENGINE CRANK ANGLE SENSOR ECM REPROGRAMMING This bulletin has been amended 2004 Sentra and Altima have been added to the Applied Vehicles The number of vehicles potentially affected has expanded Please discard all previous versions of this bulletin CAMPAIGN I D R0606 NHTSA 06V 242 APPLIED VEHICLES 2003 2004 Altima L31 with QR25DE Engine 2003 2004 Sentra B15 with QR25DE Engine APPLIED VINS 2003 Altima 1N4AL11 3C 100000 355207 2004 Altima 1N4AL11 4C 100000 199931 2003 Sentra 3N1AB51 3L 716572 736783 2004 Sentra 3N1AB51 4L 455966 977739 NOTE Use Service Comm to determine campaign eligibility INTRODUCTION Nissan has determined that on some 2003 2004 Altima and Sentra vehicles with the 2 5 liter engine the operation of the crank angle sensor is significantly affected by variations in temperature that occur due to the unique location of the sensor in the engine Under certain driving conditions these variations in temperature can be large enough to cause a brief interruption in the signal output from the sensor If the interruption in the signal from the sensor is so brief that the Electronic Control Module ECM logic does not have time to diagnose the condition the engine may stop running without warning while the vehicle is driven
17. al law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days Thank you for your cooperation We are indeed sorry for any inconvenience this may cause you 25 25
18. eps 17 18 and 19 Figure 12 Section 2 Confirm the vehicle s battery voltage and CONSULT II Charger Input 17 Press SUB MODE see Figure 11 Battery Charging then CONSULT II Elapsed Discharge Charge Time Vehicle Vole 0091 02 00 00 00 00 01 02 Mole A Press DOWN 4 times Battery Voltage Charger Input MUST BE ABOVE m 2 1 2 1 5 12 00 VOLTS B Select BATTERY CHARGE 8 3 Check Charger 0 10 20 30 40 50 60 70 80 90 100 Input without power Battery Charge IDLE supply connected Start Discharge amp Charging Charge Input reading see Figure 13 TP030625 Figure 13 NOTE e Battery Voltage is the voltage level of CONSULT II s battery e Charger Input is the voltage level of the vehicle s battery It must be above 12 volts 15 25 19 The Charger Input reading MUST be above 12 volts see Figure 13 on page 15 e A reading above 12 volts confirms a b C The DLC II is properly connected to the vehicle The vehicle battery voltage is sufficient for ECM reprogramming and CONSULT II has a sufficient power supply to perform ECM reprogramming e f the vehicles battery voltage Charger Input is below 12 volts one or more of the following may be the cause a The battery charger you hooked up in section 1 is not charging the battery poor connection or it is not working
19. er for future reference 23 Press BACK to return to the main menu 17 25 24 Select the ECM program to install see Figure 16 25 The REPROGRAM START window should appear see Figure 17 e NOTE If you get an error message refer to the ECU Reprogramming Software Operations Manual ECM damage can occur SELECT ECM PROGRAM NOTE To 23710 2Y919 This is only OOMY A33 VQ30 FED GAN AT NATS without T an example N NX Your data will differ DOWN BACK LIGHT COPY TP030631 Figure 16 REPROGRAM START INSTALLING NEW DATA A CAUTION W LOW BATTERY CONDITION MAY CAUSE ECM DAMAGE ALL ELECTRICAL LOADS MUST BE OFF DURING REPROGRAMMING START MODE BACK LIGHT COPY CAUTION DURING REPROGRAMMING e Do not unplug CONSULT II from the vehicle during reprogramming Permanent e Do not open any door or the trunk during reprogramming e On some vehicles the cooling fans may come on during reprogramming This is a normal condition Do not disconnect the cooling fans Forgetting to reconnect them may cause severe engine damage A vehicle battery charger is needed to maintain the battery voltage level during reprogramming You should have hooked up a battery charger in Section 1 TP990871 Figure 17 26 Press START ECM REPROGRAMING e After a few seconds the window BEEN CONELETEIY ERASED S
20. n 31 Remove the reprogramming CARD from CONSULT II and insert the Diagnostic Card red white card 32 Start the engine 33 Make sure all DTCs are cleared erased e f necessary erase any DTC s that may have stored during the reprogramming procedure 34 Perform the Idle Air Volume Leaning Procedure on the next page 35 Check engine idle speed Target Idle Speed No Load in P or N 700 50 rpm 36 Confirm the engine is operating normally END 21 25 IDLE AIR VOLUME LEARNING IAVL PROCEDURE 1 NOTE The IAVL procedure will normally complete within 2 minutes after Procedure Start Use CONSULT II to confirm perform the following Pre Conditions NOTE The IAVL procedure will self cancel if any of the following Pre Conditions are not met and maintained for as long as the procedure is running DATA MONITOR SIGNALS ENGINE PRE CONDITIONS COOLAN TEMP S C OR F Between 158 203 F 70 95 C More than 12 9Vatidle BATTERY VOLT V More than 12 9V at idle ON Transmission in either Neutral or Park AIR COND SIG ON OFF OFF Air conditioner HVAC switch off OFF Lighting switch and or rear defogger off 0 Vehicle speed 0 mph WORK SUPPORT SETTING ENGINE s s sSSCidCY After warming up the engine and confriming all of the above preconditions then 2 Turn the ignition OFF and wait at least 10 seconds Using CONSULT II select WORK SUPPORT gt DLE AIR
21. return to step 6 on page 8 11 25 File Transfer Complete Power off CONSULT II and Disconnect Cables TP030624 Figure 9 11 When transfer is complete see Figure 9 A Select click on Okay then MAIN MENU B Turn OFF CONSULT II C Disconnect the AC power cord and the Ethernet cable from CONSULT II 12 25 DOWNLOAD NEW DATA FROM CONSULT II INTO THE VEHICLE REPROGRAM ECM CAUTION e Perform this operation in four 4 sections DO NOT SKIP any of these sections e They must be performed in order 1 through 4 Section 1 Connect a battery charger and CONSULT II to the vehicle Section 2 Confirm the vehicle battery voltage and CONSULT II Charger Input Section 3 Perform ECM Reprogramming Section 4 Perform ECM Reprogram Confirmation Section 1 Connect a battery charger and CONSULLT II to the vehicle 12 Confirm the ignition switch is OFF 13 Connect a battery charger to the vehicle battery A Set the charger at a low charge rate trickle charge 14 Connect CONSULT II to the vehicle using the DLC II cable with black Converter Box see Figure 10 on next page 13 25 VERY IMPORTANT e Make sure the DLC II is straight and fully plugged in to the vehicle e Make sure all other DLC II cable connections shown in Figure 10 are connected properly Power oe CONSULT II Converter w r A J44200 50 E M eo DDL Port ay on CONSULT II Na DLC lI
22. shown in Figure 18 will appear CANCELLING THE PROCESS WILL DESTROY THE ECM H 111 nS 0 e CONSULT II will now turn OFF its a screen backlight W111 20 40 60 80 SUB CPU BEING REPROGRAMMED e When the screen backlight goes H s MAIN CPU WILL BE REPROGRAMMED OFF ECM reprogramming has AFTER SUB CPU started NOTE This process will take from 10 to 20 minutes TP990872 Figure 18 CAUTION You must leave the vehicle and the CONSULT II unit undisturbed don t touch until reprogramming is complete NOTE If CONSULT II screen gives you an error message Unmatch of Vehicle Data e You tried to reprogram with an incorrect data file or e You are trying to reprogram with a file that is already in the ECM 27 When the Reprogramming is NENEK NOTE complete CONSULT II will beep signa oss These numbers turn the screen backlight back ON and are only examples automatically print out a report see Cee aka Your numbers Figure 19 PART NUMBER will differ 23710 3Y11X CALIBRATION ID e Remember it may take up to 20 minutes 13Y11X CVN 03FA5CB7 OLD CALIBRATION ID e Attach the print out to the repair 13Y116 order for future reference TP990873 Figure 19 CAUTION If CONSULT II prints REPROGRAMMING UNEXPECTEDLY TERMINATED e The ECM has been permanently damaged and will require replacement e Inthis case perform steps A through G on page 2
Download Pdf Manuals
Related Search