ITB12-019 - InfinitiG37.com
Contents
1. QY INFINITI SERVICE BULLETIN COPYRIGHT NISSAN NORTH AMERICA INC Classification Reference Date BT 12 002 ITB12 019 April 17 2012 G SEDAN PAINT CHIPPING OFF EDGE OF TRUNK LID APPLIED VEHICLES 2007 2012 G25 G35 G37 Sedan V36 APPLIED VINS amp 2007 2011 G25 G35 G37 Sedan ALL DATES 2012 G25 2WD Vehicles built before JNIDV6AP CM 812266 Jan 31 2012 AWD Vehicles built before IN1 DV6AR CM 862082 Feb 1 2012 2012 G37 2WD Vehicles built before JNICV6AP CM 628061 Jan 31 2012 AWD Vehicles built before IN1 CV6AR CM 680590 Jan 31 2012 IF YOU CONFIRM Paint is chipping off the edge of the trunk lid in the locations Paint chipping shown in Figure 2 Surface corrosion in this area may also be visible ACTION 1 Inspect the trunk lid for proper clearance and latching and make adjustments if needed Figure 1 Adjust the bumper rubbers stoppers Confirm the rear combination lamp lens located below the chipped paint is flush even with the housing If not flush even replace the rear combination lamp assembly Tr S e P Using standard auto body repair practices perform a Refinish Half Block Repair to the area of the trunk lid where paint has chipped off Paint chipping off trunk edge in these locations TA i mN Figure 2 IMPORTANT The purpose of ACTION above is to give you a quick idea of the work you will be performing You MUST closely follow the entire Servic2. position of the rear combination lamp located below the chipped paint a Visually inspect and run your finger along the top of the rear combination lamp lens in the area shown in Figure 9 b Ifthe lens is positioned above the rear combination lamp housing see Figure 10 within the area shown in Figure 9 replace the affected rear combination lamp assembly c Ifthe lens is flush even with the housing proceed to step 5 ps E RH side shown inspect LH rear combination lamp lens if paint chipping is on the driver s side Figure 9 5 6 ITB12 019 5 Using standard auto body repair practices perform a Refinish Half Block Repair to the area of the trunk lid where paint has chipped off 6 6 ITB12 019
3. e Procedure as it contains information that is essential to successfully completing this repair Infiniti Bulletins are intended for use by qualified technicians not do it yourselfers Qualified technicians are properly trained individuals who have the equipment tools safety instruction and know how to do a job properly and safely NOTE If you believe that a described condition may apply to a particular vehicle DO NOT assume that it does See your Infiniti dealer to determine if this applies to your vehicle 1 6 PARTS INFORMATION DESCRIPTION PART QUANTITY RH Rear Combination Lamp 26550 JK60D 1 if needed LH Rear Combination Lamp 26555 JK60D 1 if needed CLAIMS INFORMATION Submit a Primary Part PP type line claim using the following claims coding DESCRIPTION PFP OPCODE DIA FRT ADJUST TRUNK LID STOPPER 84840 EJ70A BX3AAA 45 0 2 OR Submit a Primary Part PP type line claim using the following claims coding DESCRIPTION PFP OPCODE FRT ADJUST TRUNK LID STOPPER amp REPLACE REAR COMB LAMP ONE SIDE B4840 EJ70A BXSBAA 0 3 OR Submit a Primary Part PP type line claim using the following claims coding DESCRIPTION PFP OP CODE FRT ADJUST TRUNK LID STOPPER amp REPLACE REAR COMB LAMP BOTH SIDES 84840 EJ70A BX3CAA 0 4 On the same repair line claim for the Refinish Half Block paint repair operation code and paint expense 2 6 ITB12 019 SERVICE PROCEDURE 1 V
4. isually inspect the clearance gap between the trunk lid and rear fender rear combination lamp back up lamp and rear bumper e f clearance gap does not appear even refer to section DLK gt Trunk Lid Assembly Adjustment in the applicable Electronic Service Manual ESM and make adjustments as instructed Visually confirm clearance gap is even between trunk lid and rear fender rear combination lamp back up lamp rear bumper TP120118 Figure 3 2 Open and close the trunk lid If abnormal force is required to close the trunk lid refer to section DLK gt Trunk Lid Assembly Adjustment in the applicable ESM and adjust the trunk striker and hinge as instructed 3 6 ITB12 019 3 Open the trunk lid and adjust both bumper rubbers stoppers a Unlock the stopper by rotating the lock nut counterclockwise until fully loose See Figures 5 and 6 b Pull the stopper outward until fully extended DO NOT remove the stopper Se ws LP T p i Aa r S es i Pull stopper outward until fully extended Figure 6 iy lt N we it ay 7 2 Figure 5 4 6 ITB12 019 c Gently lower the trunk lid increasing pressure slowly until it latches d Open the trunk lid then hold each stopper in place while rotating the lock nut clockwise until it stops The stoppers are now locked in position Rotate 4 a Stopperislocked a N ae BAY i ra as Figure 7 Figure 8 4 Confirm the
Download Pdf Manuals
Related Search