20387 Instructions
Contents
1. until the assembly Is tight and in proper position 4 Continue to turn the forcing screw with a wrench or air ratchet until the wedge has spread the pitman arm sufficiently to allow the pitman arm to be removed Use caution not to spread the arm excessively Here at Tiger Tool your satisfaction is our number one Refer to steering box manufacturer s service instructions priority Should you have any questions about this or any or vehicle service manual for further information of our products please call us at 1 800 661 4661 gt View demonstration videos anda Technical Support complete product list at 1 800 661 4661 TGE Pitman Arm Spreader Heer 10386 en Parts Breakdown Ss Item No Part Number Description Qty 1 10386 1 Pull Bar 1 2 10386 2 Forcing Screw 1 3 10386 3 Anvil 1 4 10386 4 Link Arm 2 5 10386 5 Wire Ring 1 6 10386 7 Coil Pin 2 View demonstration videos anda Technical Support complete product list at 1 800 661 4661 TGE Pitman Arm Puller Sheppard M100 ess 10385 MENTE Parts Breakdown Item No Part Number Description Qty 1 10407 2 Body 1 2 10385 1 Forcing Screw 1 View demonstration videos and a Technical Support complete product list at 1 800 661 46612. NGEF Pitman Arm Service Kit Heer 2 0 3 8 7 Have What It Takes Safety Warning Read all instructions and safety warnings prior to operation Failure to do so could result in equipment damage personal injury or even death CAUTION 10385 ALWAYS KEEP THE FORCING SCREW THREADS CLEAN AND WELL LUBRICATED LUBRICATE WITH OIL BEFORE EVERY USE FAILURE TO DO SO CAN RESULT IN THREAD SEIZURE IN THE TOOL CAUTION 10386 KEEP THE THREADS OF THE SCREW CLEAN AND LUBRICATED AT ALL TIMES TO LESSEN FRICTION USE QUALITY OIL ON THREADS WE DO NOT RECOMMEND USING ANTI SEIZE Stay Alert Watch what you are doing and use common sense when e Do not overreach Keep proper footing and balance at all times operating this tool Dress properly Do not wear loose clothing or jewelry e Inspect product for damage prior to using do not use if product is Keep your hair clothing and gloves away from moving parts in unsafe condition e Keep your work area clean and well Lit e Do not operate tool while under the influence of drugs alcohol or medication e Always use safety equipment to prevent injuries Approved face and eye protection must always be worn by the operator as well as others in the work area View demonstration videos anda Technical Support complete product list at 1 800 661 4661 TGE Pitman Arm Service Kit HGEr 2 0 3 8 7 Have What It Takes Operating Instructions Sheppard M100 Pitman Arm Puller 10385 CAUTION Always
3. keep the forcing screw threads clean and well lubricated Lubricate with oil before every use Failure to do so can result in thread seizure in the tool 1 Remove set screws from pitman arm or bend lock tabs for removal of retaining bolt Refer to the manufacturer s service manual to determine model and retaining method 2 Some applications may also require removal of some all of the fasteners in the sector shaft cover to allow the tool to slide over the pitman arm 3 Back the forcing screw out and slip casting over the pitman arm until the forcing screw lines up with the center of the sector shaft Ensure that the forcing screw will not damage the threads in the end of the sector shaft On some models it may be necessary to install a bolt into the threaded end of the sector shaft for the pulling operation 4 Once the tool Is properly positioned on the pitman arm apply 2 drive impact to the forcing screw until the pitman arm is removed from the sector shaft Pitman Arm Spreader 10386 CAUTION Keep the threads of the screw clean and lubricated at all times to lessen friction Use quality oil on threads We do not recommend using anti seize 1 Remove the nut from the thru bolt 2 Remove the thru bolt from the pitman arm 3 Slide the two link arms onto each side of the pulling bar with the pulling pins entering the thru bolt hole of the pitman arms Align the wedge with the parting line of the pitman arm and hand tighten the screw
Download Pdf Manuals
Related Search