NV200 manual set
Contents
1. require occasional cleaning Do not use solvent based cleaners such as alcohol petrol methylated spirits white spirit or Do not use solvent based PCB cleaner Using these solvents can cause cleaners on any part of the permanent damage to the units only use a mild _NV200 unit __ detergent solution as directed below AN Caution You can clean the NV200 note path with the head unit still fitted to the chassis although you may find it easier to remove the head from the chassis assembly To remove the NV200 head unit first unlock the NV200 cashbox and head release lock if fitted Then lift the silver head release catch located on the front of the NV200 Meet release Finally slide the head unit forward and lift it off the chassis Copyright Innovative Technology Ltd 2014 gt GA00620 2 NV200 Manual Set Section 2 4 AN WARNING You should disconnect the power BEFORE carrying out any cleaning operations to avoid the risk of Disconnect power BEFORE causing damage to the validator any cleaning operation After removing the head unit to open the note path cover pull the top cover release latch forward towards the bezel and lift the cover as shown here it is recommended to also remove the front bezel to allow correct cleaning of the note path guides Cover release latch Note path guides The note path is now visible and can be cleaned Carefully wipe the surfaces with a soft lint free2. CTION 2 NV200 MANUAL SET Innovative Technology assume no responsibility for errors omissions or damages resulting from the use of information contained within this manual AUS Spielger te GesmbH ocheyagasse 48 A 1210 Wien We fel 43 7 277 66 00 Fax 43 1 271 66 00 75 E mail verkaufi aus at hito www aus at Offnungszeiten Mo Fr 9 18 Uhr NV200 Manual Set Section 2 2 NV200 MANUAL SET SECTION 2 2 FIELD SERVICE MANUAL 3 Pad Cleaning 3 2 2 Fault Finding Flash Codes 5 2 3 Technical Specifications 6 2 4 Frequently Asked Questions 7 2 9 Spare Parts 8 Copyright Innovative Technology Ltd 2014 gt GA00620 2 NV200 Manual Set Section 2 3 2 FIELD SERVICE MANUAL This section is one part of a complete manual set typically a field service engineer who is maintaining the product would use this section This section contains the essential information that the field engineer needs to clean maintain and fault find an NV200 Validator that is installed in a host machine The NV200 Validator has been designed to minimise any problems or performance variations over time This has been achieved by careful hardware and software design this attention to the design means there is very little user maintenance required 2 1 Cleaning The NV200 Validator has been designed in a way to prevent damage and airborne contamination reaching the optical sensors however depending upon the environment the NV200 may
3. a DA3 unit e There can be many reasons why you may be having problems using a DA3 unit to program the validator Please check the following That the DA3 firmware is up to date That the VPS is up to date Make sure pin 9 is removed from the CN00215 ribbon cable as shown here 1 Jen O _ If using override download make sure the file is selected for override during the DA3 update Check the validator is using SSP interface there is no visible indication as to which interface the NV200 is using so toggle dipswitch 8 on the NV200 and retry the update procedure If the problem persists contact ITL Support for further assistance c The cashbox is inserted but the bezel is flashing 2 red flashes and 1 blue flash cashbox removed Make sure that the cashbox is fully inserted and latched If the problem persists contact ITL Support for further assistance Copyright Innovative Technology Ltd 2014 gt GA00620 2 NV200 Manual Set Section 2 2 5 Spare Parts Full details of the interface cable connector pinouts connector types makes and other related information can be found in Section 4 of this manual set The user can obtain the following parts for the NV200 validator CNOO214 USB Cable USB 2 0 Compliant Type A to Type B cable I 5 MAX IL MAX IL TS MIN Notes USB cable should be USB 2 0 compliant electri
4. cally shielded and less than 5 metres long Copyright Innovative Technology Ltd 2014 gt GA00620 2 NV200 Manual Set Section 2 CNOO292 IF10 SSP to Binary interface cable Provides connection between IF10 module and NV200 5 1 BEBEEBEEB 2 16 Front View Front View 1 2 Top View Bottom Wiew Copyright Innovative Technology Ltd 2014 gt GA00620 2 NV200 Manual Set Section 2 CN00414 RS232 to NV200 interface cable on 12V or 24V supply and RS232 communications to 1460 20 20 20 Ld Z OOUUUOUO ill Teeth Top View pees er Black OV ii Optional Banana Plugs Copyright Innovative Technology Ltd 2014 gt GA00620 2 NV200 Manual Set Section 2 CNO0459 NV200 power cable Provides 12V or 24V supply only to NV200 Stripped no tinning Notes Recommended ferrite core is Fair Rite Part Number 0443166651 Copyright Innovative Technology Ltd 2014 gt GA00620 2 NV200 Manual Set Section 2 PA00610 Bezel Assembly PA00621 NV200 Validator Head Assembly PA00629 Cashbox Final Assembly PA00630 Chassis Assembly PA00650 Lock Assembly Copyright Innovative Technology Ltd 2014 gt GA00620 2
5. cloth that has been moistened with a water and mild detergent solution e g household washing up liquid be very careful when cleaning around the sensor lenses and make sure they are clean and dry before closing the cover and restarting the unit AN Caution Do not lubricate any of the note transport mechanism or any part of the note path as this Do not use any lubricants can affect the operation of the validator AN WARNING Do not attempt to disassemble the validator n SSNS head trying to do this could cause personal Do not try to disassemble injury and will damage the unit beyond repair Copyright Innovative Technology Ltd 2014 r GA00620 2 NV200 Manual Set Section 2 5 2 2 Fault Finding Flash Codes The NV200 Validator has inbuilt fault detection facilities If there is a configuration or other error the NV200 front bezel will flash in a particular sequence and a summary of the Bezel Flash Codes for the NV200 is shown below Red ae me Red Blue None S Note path open Close note path Note path jam Remove obstruction and follow the cleaning procedure in Subsection 2 1 of this manual Unit not initialised Contact ITL technical support Cashbox removed Refit cashbox Cashbox jam Remove trapped notes Download new firmware Interface checksum error EEPROM checksum error Download new firmware Dataset checksum error Power supply too low Check power suppl Power supply too high j PPY Card f
6. ormat Reprogram programming card Payout reset Turn power on and off Firmware mismatch Reprogram unit Copyright Innovative Technology Ltd 2014 gt GA00620 2 NV200 Manual Set Section 2 6 2 3 Technical Specifications The full technical specifications for the NV200 Validator can be found in Section 6 Appendix B of this manual set A brief summary is given here DC Voltage Minimum __ Maximum __ Nominal Standb Peak motor stall Interface Logic Levels _ Logic Low LogicHigh _ __ _ Inputs CF OV tO OSV 3 7 V to 12 V Outputs 2 2 kQ pull up Pull up voltage of host interface Maximum current sink 50 mA per output NOTE Only the later models of NV200 are capable of using a supply voltage up to 24 V DC A WARNING Earlier versions have a maximum voltage of 13 2 V Use correct supply voltage DC See Section 6 Appendix E of this manual set for information on how to identify if your validator supports 24V DC operation We recommend that your power supply is capable of supplying 12V DC at 4 3 A or 24V DC at 2 1 A Copyright Innovative Technology Ltd 2014 gt GA00620 2 NV200 Manual Set Section 2 7 2 4 Frequently Asked Questions a What settings should I use on the DIP switches on the rear of the unit e Look at the DIP switch tables in Section 1 of this manual set subsection 1 3 By default all DIP switches are turned OFF b Iam having problems programming the NV200 using
Download Pdf Manuals
Related Search