NISSAN RECALL CAMPAIGN BULLETIN
Contents
1. to do a job properly and safely NOTE If you believe that a described condition may apply to a particular vehicle DO NOT assume that it does See your Nissan dealer to determine if this applies to your vehicle 1 6 PROCEDURE TIPS for driver side air mix door motor replacement Tip 1 Tip 2 Use the Service Manual for the step by step replacement information Review the Tips in this bulletin and apply them at the appropriate place in your work flow IMPORTANT e Follow all cautions warnings and notes in the Service Manual when working on or near a Supplemental Restraint System SRS such as an air bag e Use covers as needed to protect interior surfaces Removal of the Heater and Cooling unit assembly is not needed The air mix door motor can be accessed with the Instrument Panel IP removed Do not drain the engine coolant or disconnect the heater hoses Do not discharge the A C system or disconnect any refrigerant lines Complete removal of the center console is not needed Do not remove the shift selector assembly Remove all mounting screws for the center console and move slide the console back about 3 inches TP110256a Figure 1 2 6 NTB11 048 Tip 3 Tip 4 Tip 5 Removal of the steering column assembly is not needed Do not remove the steering column mounting bolts Do not remove the tilt motor and sensor Remove steering wheel Remove combination switch and Spiral cab2. NISSAN NORTH AMERICA INC N Technical Bulletin SERVICE BULLETIN Classification Reference HA11 004 NTB11 048 2004 2011 TITAN AND ARMADA DRIVER SIDE AIR MIX DOOR MOTOR REPLACEMENT APPLIED VEHICLE 2004 2011 Titan A60 2004 2011 Armada TA60 IF YOU CONFIRM e The air mix door motor driver needs to be replaced for any reason ACTIONS e Remove the Instrument Panel IP to gain access to the air mix door motor driver e Replace the motor with the one listed in the Parts Information e Use the Procedure Tips in this bulletin as a job aid in combination with the Service Manual for replacement of the air mix door motor driver NOTE The step tips in this bulletin are not intended to be complete details for replacement of the driver side air mix door motor They are only helpful additions tips to be used in combination with the Service Manual PARTS INFORMATION DESCRIPTION PART QUANTITY Air Mix Door Driver 27743 ZPOOA CLAIMS INFORMATION Submit a Primary Part PP type line claim using the following claims coding DESCRIPTION PFP OP CODE FRT RPL Driver Side Air Mix Door Actuator 27743 ZS00A TC32AA 1 Refer to the current Nissan Warranty Flat Rate Manual and use the Indicated FRT Nissan Bulletins are intended for use by qualified technicians not do it yourselfers Qualified technicians are properly trained individuals who have the equipment tools safety instruction and know how
3. gure 6 Ventilator duct Figure e Removing ducts will allow access to the air mix door motor driver See Figure 7 i lg _ oe 1 T 1 Pr i le Prs i e a z3 oe a ae ee oe ee ea Air mix door motor driver 5 6 NTB11 048 INSTRUMENT PANEL ASSEMBLY Exploded View SEC 660 10 13 18 18 25 28 41 Defroster grille Speaker grille outer 2 E Instrument panel and pad assembly 4 Instrument upper panel LH Lower knee protector Steering column cover lower Hazard switch Fuse access cover Audio switch RH Audio switch LH Center ventilator assembly RH Metal clip 11 14 17 20 2a 20 28 a ral ru Ld Center speaker grille Speaker outer Side ventilator assembly LH Cluster lid A Instrument lower panel LH Cluster lid lower Cluster lid Glove boo AC and AV switch assembly Center ventilator assembly LH Side ventilator assembly RH Clip 12 18 21 24 2T 30 ad Speaker center Instrument panel upper cover Combination meter Key cylinder escutcheon Steering column cover upper PWD switch if equipped Instrument lower cover RH Instrument lower panel RH Audio unit Disolay assembly Instrument upper panel RH 6 6 NTB11 048
4. le Removal of the speakers center and both outer is not needed Refer to IP exploded view on page 6 The center speaker electrical connector can be disconnected once the display unit is removed The left side outer speaker electrical connector can be disconnected by reaching through the instrument cluster opening after the cluster is removed The right side outer speaker electrical connector can be disconnected by reaching through the glove box opening after the glove box is removed lf equipped the GPS sensor and harness must be removed disconnected before removing the IP GPS sensor is located at the front center of the IP under the defroster grill Remove the two mounting bolts from the GPS sensor TETI 0255 Figure 3 3 6 NTB11 048 0 naa ee speaker e With the display unit removed Sk e connector unclip the GPS harness from the A IP harness clip te Seer Rioss Tip 6 Mark the location of the 9 front IP mounting screws see Figure 5 This will help with reassembly P LEJ i 5 fi F fe a Jm r i F f i T Sane i z 4 Mi N i TE Eri j tS a oe e gt k F barn zt 1 ER LT Bi 10262 Figure 5 Tip 7 After removing the IP e Do not disconnect remove the IP wiring harness e Do not unbolt remove the steering member dash support tube 4 6 NTB11 048 Tip 8 Remove passenger side right side demister duct and ventilator duct see Fi
Download Pdf Manuals
Related Search