Home

Service Bulletin 10-059

1. 2004 Element From VIN 5J6YH1 4L000001 thru 5J6YH1 4L016571 From VIN 5J6YH2 4L000002 thru 5J6YH2 4L039857 Not all vehicles within the VIN ranges are affected by this recall Before beginning work on a vehicle verify its eligibility by checking at least one of these items e The customer has a notification letter e The vehicle is shown as eligible on a VIN status inquiry In addition check for a punch mark above the seventh character of the engine compartment VIN A punch mark in that location means the ignition switch key interlock has already been inspected repaired Some vehicles affected by this campaign may be in your used vehicle inventory As a matter of federal law these vehicles must be repaired before they are sold Should a dealership sell an unrepaired vehicle that subsequently causes an injury or damage because of the recalled item the dealership will be solely responsible to the damaged party and will be required to defend and indemnify American Honda for any resulting claims To see if a vehicle in inventory is affected by this campaign do a VIN status inquiry before selling it CUSTOMER NOTIFICATION All owners of affected vehicles will be sent a notification of this campaign An example of the customer notification is at the end of this service bulletin CORRECTIVE ACTION Inspect the ignition switch and if needed install a Key Interlock Repair Kit 1 of 6 CUSTOMER INFORMATION
2. The information in this bulletin is intended for use only by skilled technicians who have the proper tools equipment and training to correctly and safely maintain your vehicle These procedures should not be attempted by do it yourselfers and you should not assume this bulletin applies to your vehicle or that your vehicle has the condition described To determine whether this information applies contact an authorized Honda automobile dealer PARTS INFORMATION INSPECTION PROCEDURE Key Interlock Repair Kit P N 06351 SDA 000 1 Remove the steering column covers Refer to section 17 of the appropriate service manual On the lower side of the ignition switch look at the INTERLOCK INTERLOCK interlock cylinder cover LEVER LEVER SPRING e If the cover is square the ignition switch was already replaced with an updated part and a key interlock repair kit is not needed Go to step 3 e If the cover is round go to REPAIR SOLENOID COVER PROCEDURE A REPAIR NOT NEEDED INTERLOCK INTERLOCK SOLENOID SCREW LEVER PIN REQUIRED SPECIAL TOOLS Interlock Slide Hammer T N O7AAC S84A100 NOTE e An initial quantity of Permalube grease to lubricate the sliding surface of the interlock lever is included with the slide hammer To order more Permalube use P N 08734 0030 To order a replacement clamping bolt for the slide hammer use T N 0O7AAC S84A400 WARRANTY CLAIM INFORMATION OP Description FRT 7255A1 I
3. a Discard 3of6 6 Wipe off any debris from the lever s sliding surface 8 on the ignition switch with a clean cloth or a cotton swab NOTE To keep debris out of the ignition switch do not clean it with compressed air SA A LL ANLAR Clean this area 7 Apply a small amount of Permalube grease to the base of the new lever Then attach the slide hammer to the new lever pin insert the lever into the ignition switch and seat the pin with the slide hammer AWM As NEW LEVER Grease the area shown NEW Wy SLIDE HAMMER 4 of 6 9 Check the installed height of the pin with vernier calipers If the height is more than 5 0 mm the pin is not seated If needed reattach the slide hammer and seat the pin NOTE It s normal for the interlock lever to be loose even when the pin is fully seated Measure the ee height of the pin from the top of the ignition switch housing Install a new spring on the lever Make sure you attach the ends of the spring correctly The right end goes into the slot on the ignition switch e The left end goes behind the notch on the interlock lever e Once the spring is correctly installed make sure the lever moves freely and returns properly NOTCH ON THE INTERLOCK LEVER 4 SLOT ON THE ff T IGNITION SWITCH NEW SPRING 10 059 10 Insert the plunger into the interlock solenoid then install the soleno
4. HONDA Service Bulletin Applies To See VEHICLES AFFFECTED 10 059 ff 2 October 1 2010 Safety Recall Accord Civic and Element Ignition Switch Key Interlock BACKGROUND Under certain conditions the interlock lever of the ignition switch may unexpectedly deform The interlock ensures the transmission is in Park before the ignition key can be removed Interlock failure may allow the ignition key to be removed when the shift lever is not in Park If the driver fails to engage the parking brake the vehicle could roll away increasing the risk of a crash VEHICLES AFFECTED 2003 Accord 2 door From VIN 1HGCM7 3A000039 thru 1HGCM7 3A037448 From VIN 1HGCM8 3A000037 thru 1HGCMB8 3A038170 2003 Accord 4 door From VIN 1HGCM5 3A000028 thru 1HGCM5B 3A147378 From VIN 1HGCM6 3A000030 thru 1HGCM6B 3A104253 From VIN 3HGCM5 3G700010 thru 3HGCM5 3G713869 2003 Civic 2 door From VIN 1HGEM2 3L038931 thru 1HGEM2 3L088293 2003 Civic 4 door From VIN 1HGEN2 3L000033 thru 1HGEN2 3L000452 From VIN 1HGES1 3L021760 thru 1HGES1 3L038440 From VIN 1HGES2 3L021580 thru 1HGES2 3L038020 From VIN 2HGES1 3H545697 thru 2HGES1 3H627468 From VIN 2HGES2 3H542947 thru 2HGES2 3H627257 2003 Element From VIN 5J6YH1 3L000001 thru 5J6YH1 3L022397 From VIN 5J6YH2 3L000046 thru 5J6YH2 3L054401 2010 American Honda Motor Co Inc All Rights Reserved ATB 44824 1010
5. XXXXXXX Example of Customer Letter October 2010 Safety Recall Ignition Key Can Be Removed When Shifter Lever Is Not in Park Dear Honda Owner This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act What is the reason for this notice Honda has decided that a defect which relates to motor vehicle safety exists in certain 2003 model year Accord and Civic vehicles and 2003 04 model year Element vehicles equipped with an automatic transmission Under certain conditions the interlock lever of the ignition switch may unexpectedly deform The interlock ensures the transmission is in Park before the ignition key can be removed Interlock failure may allow the ignition key to be removed when the gear selector lever is not in Park If the driver fails to engage the parking brake the vehicle could roll away increasing the risk of a crash What should you do Call any authorized Honda dealer and make an appointment to have your vehicle repaired The dealer will remove the original interlock pin and lever within the ignition switch and replace them with new redesigned components free of charge Please plan to leave your vehicle for half a day to allow the dealer flexibility in scheduling Who to contact if you experience problems If you are not satisfied with the service you receive from your Honda dealer you may write to American Honda Motor Co Inc Ho
6. ealer please call Honda Automobile Customer Service at 800 999 1009 and select option 4 We apologize for any inconvenience this campaign may cause you Sincerely American Honda Motor Co Inc Honda Automobile Division 6 of 6 10 059 October 1 2010 Dear Service Manager Honda has announced a safety recall campaign for certain 2003 Accords 2003 Civics and 2003 04 Elements Under certain conditions the interlock lever of the ignition switch may unexpectedly deform The interlock ensures the transmission is in Park before the ignition key can be removed Interlock failure may allow the ignition key to be removed when the shift lever is not in Park If the driver fails to engage the parking brake the vehicle could roll away increasing the risk of a crash Repair Strategy The repair is to inspect the ignition switch and if needed install a key interlock repair kit For repair parts and warranty information refer to Service Bulletin 10 059 Safety Recall Accord Civic and Element Ignition Switch Key Interlock Some vehicles affected by this campaign may be in your used vehicle inventory As a matter of federal law these vehicles must be repaired before they are sold Should a dealership sell an unrepaired vehicle that subsequently causes an injury or damage because of the recalled item the dealership will be solely responsible to the damaged party and will be required to defend and indemnify American Honda for any res
7. id using a new screw Make sure the groove of the solenoid plunger is in the fork on the lever ORIGINAL YERA Z Sa J SOLENOID J2 WN Be sure the plunger is back in the solenoid Make sure the plunger fits back into the fork in the new lever 11 Install a new plastic cover on the interlock solenoid 12 Check the operation of the ignition switch key interlock e Set the parking brake and turn the ignition switch to ON Il e While pressing the brake pedal shift the transmission to Neutral e Try turning the ignition switch to LOCK 0 If you cannot turn the switch to LOCK 0 your repair was successful go to step 15 If you can turn the switch to LOCK 0 the interlock is not working go to step 13 13 Remove the solenoid cover and make sure the solenoid plunger groove is installed in the fork on the lever e f needed correct the position of the solenoid plunger then go to step 14 e If the solenoid plunger is correctly installed there is an electrical problem with the key interlock system refer to the Automatic Transmission section of the appropriate service manual for troubleshooting information Once the key interlock is working normally go to step 14 14 Install the solenoid cover 10 059 15 Reinstall the steering column covers 16 Center punch a completion mark above the seventh character of the engine compartment VIN Center punch here J 1HGCXXXXXX
8. nda Automobile Customer Service Mail Stop 500 2N 7A 1919 Torrance Blvd Torrance CA 90501 2746 If you believe that American Honda or the dealer has failed or is unable to remedy the defect in your vehicle without charge within a reasonable period of time 60 days from the date you first contact the dealer for a repair appointment you may submit a complaint to Administrator National Highway Traffic Safety Administration 1200 New Jersey Ave SE Washington DC 20590 5 of 6 Or call the toll free Safety Hotline at 888 327 4236 TTY 800 424 9153 or go to http www safercar gov What to do if you feel this notice is in error Our records show that you are the current owner or lessee of a 2003 Accord or Civic or 2003 04 Element involved in this campaign If this is not the case or the name address information is not correct please fill out and return the enclosed postage paid Information Change Card We will then update our records If you previously paid to have the ignition interlock replaced you may be eligible for reimbursement Refer to the attached Instructions for Reimbursement for the eligibility requirements and the reimbursement procedure Lessor Information Federal law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within 10 days If you have questions If you have any questions about this notice or need assistance with contacting a Honda d
9. nspect the ignition switch 0 2 A Add for installing a key interlock repair kit 0 1 3 Reinstall the steering column covers Spartak PIN 35100 SDA AJ1 4 Center punch a completion mark above the Defect Code 5GC00 seventh character of the engine compartment VIN Symptom Code R4400 Skill Level Repair Technician Center punch here 1HGCXXXXXXXXXXXXX 2 of 6 10 059 REPAIR PROCEDURE 1 Remove and discard the plastic cover from the ignition switch key interlock solenoid IGNITION SWITCH 4 i Eio SCREW Discard PLASTIC COVER Discard The groove of the solenoid plunger is in the fork on the interlock lever 2 Note the position of the interlock solenoid plunger you ll need to install it the same way 3 Remove the screw from the solenoid but keep the solenoid attached to its electrical connector Discard the screw NOTE e Be careful not to lose the solenoid plunger it slides out easily e Keep the plunger free of dirt and grease while it s removed from the solenoid 4 Note the position of the interlock lever spring you ll need to install the new spring the same way INTERLOCK LEVER SPRING 10 059 Attach the slide hammer to the interlock lever pin and tighten the slide hammer clamping bolt Then use the slide hammer to remove the pin Discard the pin the lever and the spring INTERLOCK LEVER PIN CLAMPING BOLT SPRING PIN Discard
10. ulting claims To see if a vehicle is affected by this campaign make sure the customer has a notification letter or do a VIN status inquiry In addition check for a punch mark above the seventh character of the engine compartment VIN A punch mark in that location means this campaign has already been completed Customer Notification Affected vehicle owners will be mailed a notification of this campaign within the next several weeks An example of the customer notification is at the end of S B 10 059 Parts Information Key interlock repair kits are available through open ordering Sincerely American Honda Motor Co Inc Honda Automobile Division

Service Bulletin 10-059

Contents

Download Pdf Manuals

Related Search

Related Contents