GENUINE PARTS INSTALLATION INSTRUCTIONS CAUTION
Contents
1. 30 Testing a Reconnect the vehicle s negative battery cable if not already connected b Tighten negative battery terminal nut to 4 1 Nm Turn the ignition switch to ON Ensure vehicle is in a failure well lit area Check to see that the green LED is illuminated If it is not press the 9 button to turn it on f Cover the forward looking photocell located to the driver side of the wire harness connection on the back of the mirror with a dark cloth or Green LED Rearward towel After a few seconds the mirror should Photocell begin to darken Timing will vary with ambient 4 Dark Cloth or light levels and a flashlight may be shined on b Towel the rearward photocell if needed to accelerate effect g Remove the cover from the forward looking photocell and the mirror will begin to clear h Push the button to ensure compass dis play shows either a direction such as NE or a C and that it can be turned ON and OFF Homelink Buttons i Push each Homelink button one at a time and verify that the LED indicator to the left of the center switch illuminates with a red LED Fig 65 C d e Red LED 31 Re install the LH front pillar finisher a Insert new clip P N 76988 JMOOA into the fin isher hole ensuring the long hook faces down Fig 66 b Insert the base of the finisher c Insert panel removal tool A between the front pillar finisher bottom side and bod2. Fig 27 d Secure harness to existing vehicle harness in trunk compartment with 4 wire ties Fig 28 The next two steps are shown with the driver side luggage side box foam assembly removed to better depict the harness routing The driver side luggage side box foam assembly does not need to be removed to route the harness f NSN AAN INA Was A e Route harness around driver side luggage side box foam assembly securing to vehicle body with 1 piece of foam tape in location shown Fig 29 Page 10 of 23 999Q6 VX300lII Rev 09 29 15 In mirror RearView Monitor 370Z Coupe f Continue routing harness around driver side luggage side box foam assembly securing to vehicle body with 1 piece of foam tape in loca tion shown Fig 30 g Continue routing harness toward passenger side following existing vehicle harness En sure harness is routed behind vehicle bracket following existing vehicle harness Fig 30 12 Establish location to attach camera bracket to vehicle body Rear Gate a Have acenter punch tool readily available Request Switch b Ensure correct orientation of camera is estab lished as per illustration Fig 31 Passenger Side License Plate c Place camera bracket onto rear of vehicle near _ Light Opening passenger side license plate light opening and rear gate request switch Fig 31 Camera Bracket Q xN Ensure camera bracket is pushed inward and toward
3. b Secure the body to harness where vehicle wire is being tapped with electrical tape 2 revolu tions 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe 25 Locate the 10mm ground bolt in driver side cowl area behind carpet and remove Fig 53 a Install ring terminal from Black wire of mir ror harness over ground bolt and reinstall Fig 53 SWESS Ay anne ae ve Lp b Ensure ground bolt is tightened to 5 9 8 0 Nm c Bundle excess Red and Black harness wires and secure along with mirror harness to exist ing vehicle harness with 1 wire tie Fig 53 26 Locate vehicle grommet at rear in trunk compartment on driver side Fig 54 CAUTION e Do not use sharp objects or objects that can damage electrical wires on next step Plastic panel tool is acceptable a If present carefully remove electrical tape from existing vehicle harness to expose electrical wires Fig 55 Page 17 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe 27 Secure Green harness wire to existing vehicle re verse circuit a Locate Tan Wire in existing wire bundle at driver side rear trunk compartment Fig 56 b See steps 20 24 pages 15 16 for wire tap installation instructions c Green mirror harness wire will be used as the accessory wire 28 Verify a clear image is displayed on the monitor a Reconnect negative battery cable b Turn t
4. from tap body b Slide the cap around vehicle wire c Tighten the tap TIGHT with finger pressure NOTE Do not re use the tap for subsequent re instal lation Page 15 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe i i Straight and evenly spaced all the way around ii Tight and minimize gap wire jacket should be crushed f Tighten i Straight and evenly spaced all around li Tight and no gap iii Test the signal Existing Accessory Harness Harness Page 16 of 23 21 Inspect the tap to ensure correct installation Fig 49 NOTE Avoid putting pressure on the vehicle wire and tap for the rest of the installation 22 Tap accessory wire Fig 50 a Remove tap non pierce side from tap b Remove the protective stub c Insert wire through the non pierce side open ing d Spread the individual strands into fan shape e Insert wire into the tap body and ensure that it is all the way in f Tighten the tap TIGHT with finger pressure 23 Confirm the tapped accessory wire Fig 51 a Inspect the tap to ensure correct installation b Test the signal to ensure that it is working properly NOTE Avoid putting pressure on the vehicle wire tap and accessory wire for the rest of the installa tion 24 Secure the tap Fig 52 a Secure the tapped wire on the non pierce side to the body of the posi tap with electrical tape 2 revolutions
5. the driver side of the trim to ensure the bracket is flush against pocket a portion of the bracket has been removed from the illustra tion to better depict the necessary information Fig 32 Rear Gate License Request Plate Light Switch Opening Center Camera Outer Fig 33 Bracket Hole Hole e While camera bracket is still positioned flush against the pocket use a center punch tool to mark the two outer holes Fig 33 f Using center punch tool mark the center hole just below the curvature of the opening Fig 33 Page 11 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe 13 Drill out camera mounting holes a Remove camera bracket from vehicle body b Protect rear of vehicle body with tape or shop towel before proceeding to next step c Using a drill and a 5 16 drill bit drill out the two outer locating holes Fig 34 d Using a drill and a 15 32 drill bit drill out the center locating hole Fig 35 e Insert a well nut into the two outer holes until the head of the nut is pressed up against the plastic trim Fig 36 Well Nut 14 Attach camera to camera bracket a Orient camera and camera bracket as shown Note locations of access hole camera label and camera cable Fig 37 Camera Label Bottom of Camera Page 12 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe b Attach camera onto camera brac
6. GENUINE PARTS INSTALLATION INSTRUCTIONS 1 DESCRIPTION In mirror RearView Monitor 2 APPLICATION 370Z Coupe 2010 3 PART NUMBER 999Q6 VX300 4 KIT CONTENTS tem A ca emess O EEC 1 wec OOO S 20 wee OOOO S Cs fome OOOO Ca ewen OOO C2 poi OOOO Po wine S C2 ms x6mm Pritip Sew O S C2 max 12mm Philip Screw SSS a users OOO 5 PRE INSTALLATION CAUTION NOTES A WARNING vVIOIZIZI ImrI Alci ITI OiInimiolo u e Disconnect vehicle battery before installing RearView Camera Kit to prevent possible shock injury during installation CAUTION e Dealer installation recommended This installation instruction will reference the service manual e This is a universal installation kit so all parts may not be used e Cut the excess wire tie s as flush with the head as possible Face head of cable tie away from sheet metal and other objects e Use caution when removing re installing interior components to avoid damage scratches or breaking of mounting clips HOMELINK AND THE HOMELINK HOUSE ARE REGISTERED TRADEMARKS OF GENTEX CORPORATION Page 1 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe CAUTION e Ensure the slack on the installed harness is removed before securing wire ties e The harness routing needs to be followed as described to avoid interferences 6 TOOLS REQUIRED 1 Clean Rag 5 3mm Flat Screwdriver 9 Torque Wrench 13 Fish Wire 2 Needle Nose Pliers 6 Pa
7. GROUND BLACK GROUND BOLT DRIVER SIDE COWL AREA RING TERMINAL DRIVER SIDE REAR 12 Pin 5PinC l gt in Connects Connects to lt Mirror c SS aoa D 5 to Camera POS 1 POS 7 N E ia Top Reverse P1 10 TAP X aF Aa a TERMINAL TAP BOLT Page 23 of 23 999Q6 VX300II Rev 09 29 15
8. eadliner and roof Fig 20 Route harness down driver side A pillar and secure to existing vehicle harness with 3 wire ties Fig 21 Page 8 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe TA Ee K MUSA LA DD lt i H UU HoH d ie hee S LT Vehicle Foam Tape Front BY ee LF ee SY mn a a ae 1 CISY On ae p S a E TfL K m Wrap 2 pieces of foam tape around mirror harness including red and black wires and tuck between vehicle body and center dash Fig 22 n Secure all mirror harness wires in footwell area to existing vehicle harness with 2 wire ties Fig 23 o Separate Red and Black wires from mirror harness Red and black wires will be used at a later step in the installation Fig 24 p Secure mirror harness without Red and Black wires to existing vehicle harness with 1 wire tie Fig 24 11 Route harness to rear gate a Secure harness to the inside of the vehicle body with 6 pieces of foam tape below existing vehicle harness in scuff plate area from A pillar to B pillar Fig 25 999Q6 VX300II Rev 09 29 15 Page 9 of 23 In mirror RearView Monitor 370Z Coupe b Attach fish wire or equivalent to harness end Fig 26 lt Fig 27 Front of Q E 22 Rear Sopa c Route fish wire from driver side of passenger Video Canie vv compartment into trunk compartment following existing vehicle harness
9. ength on the bottom side Once complete cut a small triangular portion approximately 4 5 mm in diameter out of the grommet to allow for the camera har ness Fig 43 b Route mirror harness through passenger side grommet and to the bottom of the vehicle near bumper area Fig 44 O Front of Vehicle c Locate both the camera connector and mirror harness connector Fig 45 d Remove black electrical tape and tubing from mirror harness end exposing connector in order to connect harness to camera harness e Route camera harness connector to mirror har Camera Mirror Harness i ness connector and connect Fig 45 Harness Connector Connector Page 14 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe f Pull mirror harness with camera harness through passenger side grommet and into ve hicle trunk compartment Fig 46 Mirror Harness Pa g Ensure excess slack of camera harness is Camera Harness pulled into the vehicle compartment Spare 18 Open engine hood _ Tire Front of a Disconnect negative battery terminal Vehicle Na 19 Secure gray end of the wire tap to larger Orange Wire in fuse panel area in driver side kick panel area Fig 47 a See steps 20 24 for wire tap installation in structions b Red mirror harness wire will be used as the ac cessory wire Fig 47 Red Black Green Orange 20 Tap vehicle wire Fig 48 a Remove cap slot side
10. he ignition switch to ON c With your foot on the brake pedal move the gear selector lever into reverse d Aclear image should display in the left hand side of the mirror Fig 57 e Move the gear selector lever back into park The image should now disappear f Turn the ignition switch to OFF CAUTION e Apply butyl gum to prevent potential leaks 29 Secure camera harness a Wrap a piece of butyl gum around camera har ness at the point where the harness lines up to the passenger rear vehicle grommet Fig 58 Vehicle Grommet Page 18 of 23 999Q6 VX300II Rev 09 29 15 Spare Wire Tie Tire In mirror RearView Monitor 370Z Coupe b Re install vehicle grommet to body ensuring the slit in the grommet is facing downward Fig 59 c To ensure water integrity confirm that the grom met is installed properly during re installation Butyl Gum Front of Vehicle d Secure harness to existing vehicle harness in trunk compartment area with 2 wire ties Fig 60 e Secure harness to existing vehicle harness in trunk compartment area with 2 wire ties Fig 61 f Remove 2 pieces of foam tape from kit con tents and attach to one another to create 1 large piece of foam tape Fig 62 Page 19 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe g Bundle excess mirror harness and secure to vehicle body with 1 large piece of foam tape Fig 63
11. ing in the mount i While still applying upward pressure with the screwdriver grasp the mirror bracket and lift the mirror up towards the headliner and off the mirror mounting bracket 2 Remove driver side kicking plate a Pull up kicking plate to disengage the pawils Fig 3 b Remove kicking plate from body panel 3 Remove driver side dash side finisher a Remove clip Fig 4 b Remove dash side finisher fixing clips with panel removal tool and then remove dash side finisher Fig 4 4 Using panel removal tool loosen driver side weather strip and remove from top of A pillar to scuff plate and from B pillar Fig 5 eee alee Page 3 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe AX CAUTION e Exercise caution when removing and installing LH front pillar finisher due to side airbag placement Refer ence Figure 6 below for further detail e Do NOT re use LH front pillar finisher clip LH front pillar finisher clip P N 76988 JMOOA MUST be re placed during re installation of finisher 5 Disengage driver side front pillar garnish fixing clip and metal clip with panel removal tool cut clip A with cutter knife and then remove front pillar garnish Fig 6 6 Partially remove trunk weather seal from rear plate and LH luggage side finisher Fig 7 Page 4 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe 7 Remove the following trun
12. k components Fig 8 a Luggage floor carpet assembly b Spare tire cover c Luggage spacer 8 Remove the following interior parts as shown in Fig 9 Refer to vehicle service manual a Tonneau cover assembly with tonneau cover b Luggage rear plate c Driver side luggage side finisher Front of Vehicle Page 5 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe 10mm Bolt d Remove driver side finisher 10mm mounting bolt Fig 10 Front of Vehicle e Slide driver side rear parcel shelf side finisher outward toward passenger side Fig 11 Front of Vehicle f Remove rear parcel shelf cover LH with panel removal tool as shown Fig 12 Front of Vehicle Front of Vehicle g Insert panel removal tool into the clearance between rear side finisher and body panel disengage clips pawls and disconnect rear speaker connector if equipped Fig 13 Page 6 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe 9 Remove passenger side license plate lamp in nu merical order shown Fig 14 a Disconnect the license plate lamp connector b Remove license plate lamp For vehicle s without spare 10 pin OE mirror connector in overhead proceed to step 10 c For vehicle s containing the spare 10 pin har ness used on the factory mirror wrap 1 piece of foam tape around connector Fig 15 d Using panel removal tool tuc
13. k harness up into the headliner toward passenger side En sure harness is not interfering with headliner Fig 15 10 Install In mirror RearView Monitor mirror a Plug the harness connector into the back of the In mirror RearView Monitor mirror b Slide the In mirror RearView Monitor mir ror base over the button on the windshield Fig 16 c Using a T 20 Torx head driver tighten the screw on the mirror mount 1 5 2 0 Nm 1 3 ft Ibs Fig 16 d Wrap 1 piece of foam tape around harness and using panel removal tool tuck between head liner and roof above EC mirror Fig 17 Page 7 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe e If a wire cover was removed from the OE mirror discard OE wire cover and grab new wire cover from kit contents Wire Cover f Route the harness into the groove of the wire cover and attach to the mirror mount Fig 18 g Slide the forks on top of the wire cover into the headliner Fig 18 h Grasp mirror and rotate downward Check to ensure wire cover sits flush against windshield Fig 19 i If there is a gap between the wire cover and windshield ensure there is enough harness slack from the mirror to the headliner Adjust if necessary j Wrap a piece of foam tape around harness at center of sun visor and where the headliner bends towards driver side door Fig 20 k Using panel removal tool tuck the wire harness between the h
14. ket and secure using 2 M3 x 6mm Phillip s screws smaller screws as shown Note access hole in order to secure one of the camera screws Fig 38 15 Attach camera bracket to vehicle body a Insert camera harness through center hole en suring harness is routed downward toward the bumper Fig 39 b Ensure correct orientation of camera and camera bracket are identified and place bracket onto vehicle body Fig 39 c Ensure camera bracket is flush against pocket refer to figure 32 for reference d Insert 2 M4 0 7 X 12MM well nut screws larger screws into locating holes and loosely secure using a Phillips screwdriver in a uniform manner If a uniform manner is not followed when loosely securing screws difficulty could arise when trying to install screws Fig 40 e Now securely tighten screws using Phillips screwdriver Rear Gate Request Switch Passenger Side License Plate Light Opening Camera lg Harness K f Route camera harness toward bottom of ve hicle bumper area Fig 41 Page 13 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe 16 Locate vehicle grommet at rear trunk compartment on passenger side pee we a Pull grommet outward disengaging from ve hicle body Fig 42 Front of O Vehicle ia 17 Cut rear grommet to allow for routing of camera har ness a Using side cutters cut a slit in the grommet approximately 8 5 mm in l
15. nel Removal Tool 10 Drill 14 Center Punch Tool 3 T 20 Torx Head Driver 7 10mm Socket Wrench 11 5 16 Drill Bit 4 1 Phillips Screwdriver 8 Side Cutters 12 15 32 Drill Bit 7 VEHICLE PREPARATION 1 Apply parking brake 2 Record the customer radio presets Preses 1 2 3 4 5 e 3 Make sure that the shift lever is engaged in the P position 4 Turn the ignition switch OFF 1 Removal of OE rearview mirror a For vehicle s having OE rearview mirror with con nector attached to back of mirror continue below step 1b For vehicle s containing OE rearview mir ror without connector attached to back of mirror proceed to step 1g on next page b Disconnect 10 pin connector from back of mirror Harness will be tucked up into the headliner at a later step c Remove and discard wire harness cover which is attached from mirror base to headliner d Using a T 20 Torx head driver loosen the screw on the mirror mount Fig 1 e Slide the mirror base off of the button on the wind shield Fig 1 f Skip to step 2 on next page Page 2 of 23 999Q6 VX300lII Rev 09 29 15 In mirror RearView Monitor 370Z Coupe g Insert the flat end of a 4mm screwdriver into the opening at the bottom of the mirror mount Fig 2 h Slide the screwdriver upward into the center of the mirror mount until resistance is felt Apply a small amount of additional upward force to lift a locking spr
16. r for damage Confirm proper operation of vehicle systems Confirm back up lamps Confirm license plate lights Confirm trunk cargo light Confirm driver side speaker in driver side rear panel if equipped Place the User Guide in the glove box Reset radio presets to the recorded settings Check the trim for proper flush fit after re installing the interior components PLL II I Ld Verify In mirror RearView Monitor has the correct amount of rear bumper present Cut out the Go No Go gauge below and place on mirror display dimensions of cut out must be measured prior to cutting to ensure accuracy of printer Bumper Visual Not Acceptable 44mm Bumper Visual Acceptable y Posi Tap is protected by patent 5 228 875 5 695 369 5 868 589 6 692 313 Jap 2881414 Aus 708700 Tia 103534 Can 2204826 Mex 200626 Korea 477279 China Z197105562 9 amp others pending Page 22 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe i Verify the camera is operating properly ic Camera should meet the below performance requirements The grey area indicated must be included in the display Vehicle width both sides 200 mm 5 000 mm e Bold lines indicate the actual field of vision A 300 mm max B 5 000 mm min TROUBLESHOOTING GUIDE FUNCTION MIRROR HARNESS VEHICLE WIRE COLOR CONNECTION LOCATION CONNECTION METHOD COLOR Vehicle IGNITION OO R O oE ORANGE MA01 POSI TAP
17. y side and press clips into body d Push the finisher toward the vehicle body to attach Long Hook Faces Down Page 20 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe Ay CAUTION e Use caution when re installing interior components to avoid damage scratches or breaking of mounting clips Refer to the vehicle specific service manual for more information e Trim pieces found to have witness marks or broken clips are not to be reinstalled 32 Re install the remaining components referring to the service manual for the vehicle A LE 33 Clean interior of vehicle ble HA S35 34 Set C Z a et Compass Zone 5 Yh i a With the display turned ON push the e button for 3 seconds until a number appears in display numbers correspond to regional compass zones b Press and release button to scroll through zone numbers c Release button when correct zone number is displayed Zone number will disap pear and display will return to showing either a directional heading or a C after 5 seconds of no switch activity 35 Calibrate Compass a Drive vehicle in circles 360 at 5 mph or less until compass display window shows a direc tion Page 21 of 23 999Q6 VX300II Rev 09 29 15 In mirror RearView Monitor 370Z Coupe 9 Post Installation Check Sheet Ensure all trim panels are fully seated properly Inspect the vehicle interior and exterio
Download Pdf Manuals
Related Search