MODEL # 610 - Parts Town
Contents
1. dlund Products for Foodservice M098 REV B JULY 2006 Edlund Company Inc 159 Industrial Parkway Burlington VT 05401 802 862 9661 SETUP AND OPERATION 1 Unpack can opener and check for any loose screws or any damage 2 Place can under the guard ring and against the locator The can should be centered 3 16 under the ring 3 Connect the airline Air should be clean and dry a 5 micron filter and coalescing filter are recommended Air requirement is 1 2 CFM at about 85 PSI The valves and cylinders are pre lubricated so no lubrication is required 4 Depress both palm buttons at the same time and hold until the lid is removed 5 Remove can with both hands and remove the lid Then the product can be dumped Avoid sharp lid edges 6 Replace opened can with another unopened can and start again The Model 625 opener is factory adjusted to open a standard 10 can or the particular size can ordered The crown punch should penetrate the can just far enough to cut off the cover but not so far as to cause excessive splashing of liquid in can If an adjustment is required to improve operation of the opener the following procedure will be used CAUTION To avoid personal injury disconnect air line before making any adjustment 1 Disconnect airline to unit 2 Place can to be opened under can guard 3 Loosen the four nuts or bolts at the rear of the vertical see drawing and raise or lower the head as desired keeping the c2. DEO 8 4 2010 Page 4 of 8 dlund Products for Foodservice M098 REV B JULY 2006 Edlund Company Inc 159 Industrial Parkway Burlington VT 05401 802 862 9661 610 Operation and Troubleshooting Operation Description 1 Place can in position against guard ring tab There should be approximately 1 8 between the top of the can and the bottom of the guard ring Adjust if necessary keeping the head level and spaced evenly 2 Connect a clean and dry air supply set to about 85 psi pressure 3 Depress both green buttons at the same time and hold down until blade hits the end of stroke and release Lid should be completely separated from the can Pneumatic Description The two green palm buttons B138 are attached to one normally open V005 and one normally closed 3 way air valve V002 The output of these two valves is connected to the pilot actuators of a 5 way valve VOIS5S The two outputs of the 5 way valve are connected to a 4 diameter air cylinder C185 which is connected to a blade A756 which removes the lid Both buttons must be actuated to shift the 5 way valve and extend the cylinder and open the can Releasing them shifts the 5 way valve back and retracts the air cylinder Troubleshooting Only qualified maintenance personnel should do repairs Symptom 1 Unit will not operate when a Check air connection and supply pressure air should buttons are pushed come out of unit when it is disconnecte
3. dlund Products for Foodservice M098 REV B JULY 2006 _ 159 Industrial Parkway Burlington VT 05401 802 862 9661 SERVICE MANUAL W098 MODEL 61 CROW Y OPENER i A Page of 8 8 4 2010 dlund Products for Foodservice M098 REV B JULY 2006 Edlund Company Inc 159 Industrial Parkway Burlington VT 05401 802 862 9661 Model 610 Crown Can Opener SAFETY PRECAUTIONS Risk of Injury Do NOT operate without guards in place WARNING 1 Do not allow any person near knife or lid remover while machine is being operated The fast high forces of air cylinders that operate the blade and lid remover can cause serious injuries The two hand controls and guards keep the operator away from these sharp moving parts Wear hand protection when handling knives open cans and lids 2 Always disconnect air while cleaning repairing or adjusting 3 Check knife for wear cracks dents or bent teeth that could cause metal slivers or food trap areas that are difficult to sanitize and could lead to sickness or internal injuries if can contents become contaminated Replace or return to the factory for repair if damaged 4 Inspect the machine before and after operating each day or shift and after any change or adjustment for 1 Loose screws 2 That the knock out pins are straight and line up with holes in the blade backing plate and that the mounting screws are tight 3 That all covers and guards are in place
4. 4 That there isn t any broken welds and 5 That the machine has been cleaned thoroughly 8 4 2010 Page 2 of 8 dlund Products for Foodservice M098 REV B JULY 2006 Edlund Company Inc 159 Industrial Parkway Burlington VT 05401 802 862 9661 Blade Cleaning and Inspection DESIRED HEIGHT UZ LEAVE 1 8 3 16 BETWEEN LOOSEN HEX BOLTS BOTTOM OF GUARD RING AND TO ADJUST CAN HEIGHT TOP OF CAN RETIGHTEN 4 ad BLADE CLIP KNOCK OUT PINS Q KNURLED SCREW MOUNTING SCREWS GUARD RING TAB CLEANING INSTRUCTIONS 1 Disconnect air supply Remove guard ring blade clip and knife and wash after use Remove two knurled screws that hold the guard ring in place It may be necessary to pull down on the guard ring to remove it if the locating pins are too tight Support the blade with your hand lifting slightly to loosen blade clip so it can be pulled out releasing the blade to drop out These parts should be sanitized in a dishwasher 2 Wash down with soap and water entire splash area around knife guard ring and lid remover 3 Entire machine can be washed 4 Reassemble blade blade clip and all guarding Be sure all screws are tight Reconnect air supply CAUTION Keep water out of airlines especially when using pressure washers Do not allow food to remain on machine Dried food deposits are unsanitary and can damage valves and cylinders 8 4 2010 Page 3 of 8
5. repaired or replaced The valve VO15S probably needs repair or replacing Remove cylinder top hose to check if only the valve VO15S is faulty If cylinder piston seals are bad air will come out of the top cylinder port Check to be sure all connections are tight and hoses are pushed all the way on If the three way valves are stuck or worn out they can leak around the actuating stem Disassembly and cleaning is possible but replacement is recommended V002 valve stuck in and or V005 valve stuck in and or VOISS valve stuck in open position and or Cylinder C185 seized in down position Repair or replace factory parts ao Te a Inspect blade for damage replace or return to the factory for reconditioning b To check cylinder stroke hold both buttons down blade should come down at least 1 1 2 to the points or 3 8 to the valley Cylinder may be loose binding or filled with water or oil and hydraulically locked repair or replace as necessary c To adjust the head height loosen bolts in back and adjust head to correct height or slightly closer being sure to keep the gap between guard ring and can even on both sides d Ifthe lid is still attached near the front or back check the gap there excessive variation before operation or too much flexing during operation can be caused by a bent frame or broken welds be sure knife is good and you have 85 psi of pressure Return to factory for repairs if frame is damag
6. 1 4 OD Fitting Push in Elbow 1 8 NPI to 1 4 OD Hose Fitting Push in Branch lee 1 8 NPI Brassto 1 4 OD Fitting Push in Fitting Elbow 1 4 NPI to 3 8 OD toot 610 700 Hose Clear 3 8 OD Hose Clear 1 4 OD Kit Rod Bushing Miller Kit Stary 1 Hod bushing Label Warning Knite cut Hazard Label Warning Keep Guardsin Place Label Cleaning Instructions Mount C185 Cylinder Nipple 2 long Nut A 414 1 3 4 12 Pin Knockout Pin Holl Pin Weld Rivet SB 5 6 screw S S 1 2 13 x 1 Hex Screw S S 1 2 13 x 3 4 Hex Screw S S 10 32 x 3 8 Hex Screw S S 10 32 x 1 4 RHM screw 8 32 x 5 16 RHM Standott 6185 Cylinder screw 1 2 13 xX 2 FHS screw YS4mm x 10 F H Slotted Valve 3 way N O Valve 3 way N C Valve Old Mac 921B RA valve b way SMG Washer S S 10 Flat Washer S S 1 2 Flat Washer S S 10 Lock Washer S S 1 2 Lock Page 7 of 8 dlund Products for Foodservice M098 REV B JULY 2006 Edlund Company Inc 159 Industrial Parkway Burlington VT 05401 802 862 9661 EDLUND CO INC 8 4 2010 Page 8 of 8
7. an and can guard aligned and level 4 Tighten fasteners and close interlock door Operate according to operating instructions If a new size can is required to be opened the following procedure will be used 1 Disconnect airline to unit 2 Hold up the knife guard ring with one hand and with the other hand unscrew the two thumb screws A flathead screwdriver may be needed to start the screws Let the guard ring down and place to the side Now hold up on the knife with one hand being careful of any sharp parts of the knife and with the other hand pull the blade clip straight out You may have to wiggle the knife to loosen the blade clip Let the knife down Place knife and clip with guard ring Do not let knife fall in the deck 3 Install desired crown punch and can guard onto opener 4 If can knockout pin does not align with holes in crown punch loosen screws holding them and rotate the pins until they line up with the holes in the knife Tighten screws and mount the knife clip and guard ring If lid remains in knife make sure knockout pins P016 are in place and that knife is retracting all the way 5 Place can to be opened under can guard If new can is taller than former size can loosen the four nuts or bolts at rear of vertical see drawing and raise head Place 1 8 3 16 inch thick shim between can and can guard Level and align head and tighten fasteners at rear of vertical Operate according to preceding instructions
8. d b Remove cover to check valve operation The valve V005 connected to the right button should only let airflow through it when actuated Remove the side hose by pushing in collar and pulling out the hose at the same time Operating the button should let air out and releasing it should stop it completely The other button and valve V002 works just the opposite If both valves are OK then remove the upper hose to the cylinder Air should only come out of this hose when both buttons are pushed If no VO15S is faulty and needs to be replaced If it checks out OK be sure cylinder is not filled with water or oil and hydraulically locked With air disconnected and the hoses to the cylinder disconnected the cylinder should be free to be pushed up and pulled down by hand If it is seized up it needs to be removed and replaced or repaired 8 4 2010 Page 5 of 8 dlund Products for Foodservice M098 REV B JULY 2006 Edlund Company Inc 159 Industrial Parkway Burlington VT 05401 802 862 9661 Symptom 2 7 8 4 2010 Air leaks out around cylinder shaft near blade Air leaks out the 5 way valve V015S exhaust Air leaks around one of the valves V002 V005 or VO15S Blade goes down but will not return Blade fails to open can completely Lid does not fall out of knife The cover must be removed to pinpoint leaks Worn seals usually cause cylinder end leaks and the cylinder must be removed and
9. ed a Bent or broken knockout pin Repair or replace b Damaged blade holding the lid Repair or replace Page 6 of 8 dlund Products for Foodservice M098 REV B JULY 2006 Edlund Company Inc 159 Industrial Parkway Burlington VT 05401 802 862 9661 01 F A600 A601 A6031 A6039 A 20 A o6J A018 A019C AU60 B132 B136M B13 B13 B B163 C084 C109 C124 C13 C185 FUU03 FUUY F018 FU36 F033 FU3 F038 FUSU F092 H02 H028 KU3Y KO 95 L211 L212 L213 MO80 NOO8 NO3Y PU16 PU28 P042 R046 SU26 3033 5049 S068 SU8 4 5349 S390 S5904 v002 VOUS V014 VU19S W010 W013 W021 W024 8 4 2010 610 PARTS LIST j ETT weldment Frame A749 F052 4 R021 K046 223 Weldment Kam Plate GU28 2 PU42 4 P103 Assy Miller Gy W Mount Only Assy A6U31 Cyl Assy W Valve Allen Air Cyl Repl Assy 10 603 Guard Hing Specity Uther Can size Assy 10 Knite Specity Other Can size Adaptor Push Button Adaptor Ham For Clip Allen Air Cyl Adaptor Swivel Eloow 1 4 NPI to 1 4 ID Hose Bushing Reduction 1 4 to 1 8 NPI Bushing snap Moditied Button Mushroom Push Button Button Only Bracket 610 Cover Clip 10 Hetaining Specitiy Other Can Size Coupling Air 38224 Cover Front Cover lop Cylinder 4 x1 5 8 NEPA side mount W Adapter Fastener soutnco Fitting 1 4 NPI Branch Fitting Swivel to 1 4 ID Hose Fitting Push in 1 8 NPI to 1 4 OD Hose Fitting Push in Short Elbow 1 8 NPI
Download Pdf Manuals
Related Search
MODEL models model 3 model mayhem model number of this laptop model y tesla model context protocol modelo beer modelscope model s plaid model o software modelo negra model cars model trains modelo especial models resource model roundup model number for my pc model name of my laptop model 3 performance model 3 tesla model electronics model society model united nations model media modeling madness