Service Manual - Troy-Bilt
Contents
1. OTROY BILT Service Manual 753 Wide Cut Mower NOTE These materials are for use by trained technicians experienced in the service and repair of outdoor power equipment of the kind described in this publication and are not intended for use by untrained or inexperienced individuals These materials are intended to provide supplemental information to assist the trained technician Untrained or inexperienced individuals should seek the assistance of an experienced and trained professional Read understand and follow all instructions and use common sense when working on power equipment This includes the contents of the product s Operators Manual supplied with the equipment No liability can be accepted for any inaccuracies or omission in this publication although care has been taken to make it as complete and accurate as possible at the time of publication However due to the variety of outdoor power equipment and continuing product changes that occur over time updates will be made to these instructions from time to time Therefore it may be necessary to obtain the latest materials before servicing or repairing a product The company reserves the right to make changes at any time to this publication without prior notice and without incurring an obligation to make such changes to previously published versions Instructions photographs and illustrations used in this publication are for reference use only and may not depict actual model and componen2. See Figure 55 4y NS Figure 55 NOTE Support the transmission during this pro cedure 16 14 13 Remove the transmission from the unit for ser vice See Figure 56 Figure 56 NOTE Contact Tecumseh Peerless for trans mission service information during the warranty period Model number information is located on the right side of the transmission See Figure 57 15 Transmission Model Number Figure 57 INSTALLATION OF WHEEL DRIVE BELT GUARDS UPDATE NOTE Current production units have additional belt guards installed at the factory This update will cover older units without pulley belt guards On older units the long run of the wheel drive belt cre ates several issues The belt may come off one of the pulleys The belt may not fully disengage from the engine pulley causing engine creep or hard shifting Servicing the Troy Bilt Wide Cut 33 Combination Mower A kit is available to correct these situations KIT NUMBER 753 04509 Contents 3 belt guides Belt Guide 1760096 e Belt Guide 1769522 e Belt Support Bracket 1768381001 Installation procedures are as follows 15 1 Using a inch socket remove the four flange screws securing the Belt Guard cover to the mower support frame See Figure 58 Figure 58 15 2 Using a 9 16 inch socket remove the lock nut securing the idler pulley to the idler arm See Figure 59 2 gt 416 we Beant _ _ l l r Pulle
3. 48 Cogged Pulley Drive Pulley E 4 p 9 Spacer Flat Washer Lock Wash Special Thrust Washer ON a Figure 48 13 12 Removed the cogged pulley assembly and spe cial thrust washer from the top of the Spindle assembly 14 13 13 Using a inch socket loosen the four mounting bolts securing the spindle housing to the deck See Figure 49 NOTE Hold the housing from underneath the deck when removing the final mounting bolt Remove the housing from the deck 13 14 Inspect the housing for excessive wear or dam age and replace as needed 13 15 Assembly is the reverse order of disassembly IMPORTANT Torque the spindle housing flange lock screws to 15 foot pounds during reassem bly IMPORTANT During assembly place Locktite 242 on the threads of the spindle shaft screw and torque to 35 ft Ibs IMPORTANT Time the blades properly during reassembly Set the cutting blades perpendicular to each other during installation of the toothed drive belt Torque the blade mounting screw to 35 ft Ibs 14 14 1 TRANSMISSION REMOVAL Remove the blade drive belt see the Blade Drive Belt Removal section 14 2 Remove the wheel drive belt see the Wheel Drive Belt Removal section NOTE While it may be possible to remove the transmission while the deck is installed it would be easier to first remove the deck 14 3 Support the frame off the ground in a way that allows you to work on the transmiss
4. a kit Part Number 1770557 If your unit uses the older style guides obtain the update kit The kit 19 Servicing the Troy Bilt Wide Cut 33 Combination Mower 20
5. with the remove the four shoulder bolts flat washers and spindle housing deck mounting bolts See Figure flange locknuts securing the deck to the lift 37 assemblies See Figure 35 a aa z Sateen ma Figure 37 Figure 35 12 4 Using a 2 inch deep socket loosen the four NOTE Maintain the proper orientation of the mounting bolts securing the right spindle hous shoulder bolts during reassembly ing to the deck See Figure 37 11 10 Remove the deck from under the unit 12 5 Using a shop rag to protect your hand hold the blade secure while removing the flange lock screw that secures the spindle shaft with an air 12 RIGHT SPINDLE REMOVAL gun and 5 8 inch socket e ride 38 12 1 Using a 2 inch socket remove the four screws securing the belt cover and remove the cover 12 2 Using a inch socket loosen the screw securing the belt tension adjustment bracket and turn it out of the way See Figure 36 Eee we z Figure 38 12 6 Remove the cutting blade and spindle shaft from the spindle housing Belt Ue aa Bracke T Figure 36 11 Servicing the Troy Bilt Wide Cut 33 Combination Mower 12 7 Remove the cogged pulley spacer washer lock washer and screw from the spindle housing Components on bench See Figure 39 Cogged Pulley A Special Thrust Washer Spacer Flat Washer Lock Washer Spindle woos Screw Spindle Shaft gt a Blade v i Blade Moun
6. 45 degree retaining ring NOTE Moving the shift arm clockwise all the tool remove the retaining ring securing the idler way to the left and then one notch counterclock arm to the deck ACEL See Figure 34 wise should put the transmission in neutral With Ju the operator presence control lever down you N A Ring should be able to easily roll the unit 10 4 With the transmission in neutral rotate the shift link until the hooked end easily fits into the hole at the bottom end of the shift rod See Figure 32 NOTE The shift rod must be held in the neutral position while the shift link is adjusted 10 5 Secure the shift link into the shift rod with the hairpin clip removed earlier 10 6 Recheck the neutral position and readjust if nec essary Check from both the forward and reverse direction Figure 34 11 DECK REMOVAL 11 6 Remove the flat washers There may be as few 11 1 Using a inch socket remove the four screws as 2 and as many as 4 washers and flange securing the belt cover and remove the cover bushing from the idler arm Inspect the flange 11 2 Remove the blade drive belt see blade drive bushing for wear belt removal section 11 7 Remove the idler arm from the deck bracket and set it on the mower support 11 8 Support the deck from below 10 Servicing the Troy Bilt Wide Cut 33 Combination Mower 11 9 Using a 9 16 inch socket and open end wrench 12 3 Align the sight holes in the right pulley
7. 5 8 While holding the Idler arm and brake away from the left blade drive pulley remove the toothed belt from around the left cogged pulley and up and over me drive pulley see ngue 17 Toothed Balt ene Figure 17 5 9 Replace the belt with a new belt Servicing the Troy Bilt Wide Cut 33 Combination Mower IMPORTANT Time the blades properly during reassembly Set the cutting blades perpendicular to each other during installation of the toothed drive belt There are arrows cast into the cogged pulleys to help align the blades Offset these arrows by 90 degrees See Figure 18 L Peni JOSE D A b f Blade Alignment Arrow N z IS Figure 18 NOTE The arrows do not indicate the blade position Blades are 90 degrees offset from the arrow position 5 10 Rotate the tension adjustment bracket into posi tion and apply tension to the spindle housing and cogged belt 5 11 Tighten the adjustment bracket screw 5 12 Tighten the four spindle mounting bolts to 15 ft Ibs NOTE Proper belt tension is achieved when the belt deflects approximately 1 2 inch at the mid point between the pulleys when applying moder ate finger pressure 5 13 Reinstall the blade drive belt over the left drive spindle 5 14 Install the belt cover BLADE BRAKE REPLACEMENT 6 1 Using a inch socket remove the four screws securing the belt cover and removed the cover 6 2 Secure the operator prese
8. A a 4 Figure 29 9 1 To adjust use a 1 2 wrench to make a small 1 4 turn adjustment to the brake locknut until the correct measurement is achieved It may be nec essary to relieve spring tension when decreas ing distance Have an assistant engage the operator presence control while you adjust the nut See Figure 30 Figure 30 10 TRANSMISSION NEUTRAL ADJUSTMENT With the unit turned off and the shift lever in the neutral detent position you should be able to hold down the operator presence control and roll the unit easily for ward and back Check this from forward and reverse positions If the unit is in gear you will need to perform a neutral adjustment 10 1 Place the shift lever in the neutral detent position of the console See Figure 31 Shift Lever Roll Pin in Detent Position U NB SO NSO B i Figure 31 Servicing the Troy Bilt Wide Cut 33 Combination Mower 10 2 Remove the hairpin clip securing the shift link 11 3 Using a recoil rope or spring removal tool and lower it from the shift rod See Figure 32 remove the extension spring attached to the deck bracket and idler arm See Figure 33 Recoil Rope M Deck Bracket Extension Spring En Idler Arm Figure 32 Figure 33 10 3 Moved the shift arm back and forth as necessary into each detent until the transmission is in neu 11 4 Remove the spring from the idler arm irai 11 5 Using a medium size
9. a 9 16 inch socket and opened end wrench remove the front idler pulley to allow the belt to be removed from around the pulley See Figure 8 1 io 7 PY Front Idler Pulley pas Rear Idler Pulley galder Pulley Mounting Bracket per sn mem O S A m e A Figure 8 NOTE Maintain correct order of parts 1 5 Using a 9 16 inch socket and opened end wrench remove the rear idler pulley to allow the belt to be removed from around the pulley See Figure 8 NOTE Maintain correct order of parts The pul ley mounts to the front hole in the idler arm 1 6 Drop the belt off the engine pulley 1 7 Replace the belt and assemble in the reverse order NOTE Maintain orientation of belt guides during reassembly See Figure 8 Lock Washer Nut re Washers Bracket Position Lock Washer Nuta 4 Pyramid Washer 3 2 3 3 Bracket Position DECK IDLER PULLEY INSPECTION Using a 9 16 inch socket and opened end wrench remove the front and rear deck idler pul leys and inspect for wear NOTE There is a pyramid washer under the front mounting bracket that helps maintain the position of the front idler pulley See Figure 9 Rear Idler i Hex Head Cap Screw Flat Washer Belt Guide Hex Head o0 foy Front Idler Pulley Belt Guide Figure 9 BLADE DRIVE BELT ADJUSTMENT Using a 2 inch socket remove the four screws securing the belt cover and remove the cover With mower on le
10. controls look inside the cutout at the left rear of the frame and make sure that the operators presence control latches are fully engaged See Figure 13 Latched Position Figure 13 4 3 To adjust remove the hairpin clip on the upper end of the operator presence control arm 4 4 Loosen the hex nut and shorten the rod by one or two turns Do not over adjust Tighten the hex nut securely See Figure 13 4 5 If properly adjusted the blade drive control will disengage when the operators presence control is released BLADE SPINDLE BELT REPLACEMENT 5 1 Using a 2 inch socket remove the four screws securing the belt cover and removed the cover 9 3 5 4 J 5 6 Servicing the Troy Bilt Wide Cut 33 Combination Mower Using a 2 inch socket loosen the screw securing the belt tension adjustment bracket and turn it out of ne vey See Figure 14 m La E 2p wN o Ww Figure 14 Align the sight holes in the right pulley with the spindle housing mounting bolts See Figure 15 T Figure 15 Using a 2 inch deep socket loosen the four mounting bolts securing the spindle housing to the deck See Figure 15 Slide the pulley assembly to the left to loosen tension on the cogged belt Remove the cogged belt from around the right cogged pulley 5 7 Temporarily remove the blade drive belt from rouna the left blade drive pulley See Figure 16 QH i beg J Blade Drive Belt
11. igure 24 l i iler S rront idler Gk T x ae ley a am P 7 Trans Pulley Belt Guide Cap Screw DA lt _ Figure 24 NOTE Maintain correct order of parts Pulley Washer Belt Guide Nut Servicing the Troy Bilt Wide Cut 33 Combination Mower 7 6 Use a 9 16 inch socket to loosen the cap screw securing the transmission pulley belt guide to the frame and engine mount Pivot the belt guide away from the pulley See Figure 24 7 7 Using a 1 2 inch socket loosen the nut securing the rear belt support bracket to the transmission Pivot the belt support away from the belt See eee 25 af Ph Rear Belt ae Bragijet ON AY Figure 25 7 8 Remove the wheel drive belt from the engine sheave backside idler and the transmission pul ley See Figure 26 INSTALL BELT INSIDE OUT l Backside Front Idler j Idler Pulley SR 5 l o l ii r7 7 T I a Engine Pulle o l i 3 i Tas kh1 i _ l Transmission Pulley Figure 26 7 9 Install a new belt in the reverse order NOTE The new belt must be installed inside out The V side of the belt lies against the engine sheave only The flat side of the belt lies against the transmission pulley and idler pulleys 8 WHEEL DRIVE BELT ADJUSTMENT The wheel drive belt requires adjustment when belt slippage occurs This is most noticeable when more tract
12. ion from Servicing the Troy Bilt Wide Cut 33 Combination Mower underneath the unit You will also be removing 14 7 Using a pair of needle nosed pliers remove the the wheels and transmission from this position hair pin securing the shift link rod to the shift rod See Figure 52 14 4 Using a inch socket remove the two screws attaching the flap bracket to the frame Remove the flap bracket See Figure 50 Shift Link Rod Mounting Screws Hair Pin Flap Bracket Figure 52 14 8 Remove the tang retaining ring securing one of Figure 50 the wheels See Figure 53 14 5 Using a pair of needle nosed pliers remove the a left rear cotter pin securing the lower brake rod Tang Retaining Ring to the brake arm See Figure 51 gt i k i r on ase h gt my 4 IS 4 i 5 r s 7 S k a S Lower Brake Rod gt P m Pa n Cotter Pin f a a lt 2 1 Figure 53 r 14 9 Remove the special washers and the wheel Figure 51 NOTE Additional wheel spacing washers can be added when required 14 6 Remove the lower brake rod from the brake arm 15 Servicing the Troy Bilt Wide Cut 33 Combination Mower 14 10 Remove the square key from the axle See Fig ure 54 Square Key Figure 54 14 11 Repeat for the other wheel 14 12 Using a inch socket and opened end wrench remove the top locknuts flat washers and screws securing the transmission to the frame
13. ion is needed such as going up slopes 8 1 Remove the hair pin clip from the upper end of the wheel drive control rod Slide the rod out of the lever assembly See Figure 27 hg i Hairpin Clip a cal sE N A JN LZ ad A Wheel Drive Control Rod Figure 27 8 2 Using a 9 16 opened end wrench loosen the jam nut on the lower end of the rod See Figure 28 Wheel Drive Control R d Figure 28 8 3 Thread the rod one or two turns clockwise for more tension 8 4 Insert the rod back into the hole in the wheel drive control lever and install the hairpin clip Servicing the Troy Bilt Wide Cut 33 Combination Mower 8 5 Test the operation of the unit Repeat the adjust ment if necessary NOTE Most comfortable operation will be obtained when the adjustment allows the lever to just make contact with the hand grip when suffi cient traction is achieved 8 6 When adjusted properly tighten the lower jam nut against the block 9 WHEEL BRAKE ADJUSTMENT This adjustment may be required it the unit does not hold on a hill with the operator presence control disen gaged or if the brake drags with the operator presence control engaged and the transmission is in neutral The unit should roll freely in this position NOTE With the operator presence control released there should be a 3 8 to 5 16 gap between the back of the brake arm and the bracket See Figure 29 k w A
14. ket loosen the four mounting bolts securing the spindle housing to the deck See Figure 43 Slide the pulley assembly to the left to loosen tension on the cogged belt 13 5 Remove the deck drive belt from around the left spindle pulley See Figure 44 13 6 Deck Drive belt i Ge f da E a A Figure 44 lt a 13 13 7 Secure the operator presence control lever to the left handlebar using a plastic tie or tape See Figure 45 SS Operator Presence Control Plastic Tie gt gt O gt 4 Figure 45 13 8 Engage the blade control lever to move the brake pad away from the drive pulley See Fig ure 46 Blade Engaged Figure 46 Servicing the Troy Bilt Wide Cut 33 Combination Mower 13 9 Using a shop rag to protect your hand hold the blade secure while removing the flange lock screw that secures the left spindle shaft with an air gun and 5 8 inch socket See Figure 47 k PEN P 4s sereee left Drive Pulley ni HOLD BLADE FROM BELOW wile on x Bi ot ca Figure 47 13 10 Remove the cutting blade and spindle shaft from the left spindle housing NOTE There will be a lock washer and flat washer securing the drive pulley to the blade spindle 13 11 Remove the drive pulley from the top of the cogged pulley NOTE There will be a spacer between the drive pulley and the cogged pulley assembly See Fig ure
15. l problems can be diagnosed using a ohm meter and checking continuity of the ignition switch and wires to each component See Figure 5 ELECTRICAL DIAGRAM MODEL E753B ONLY IGNITION SWITCH WIRE COLOR CODE B Black ue Solenoid Regulator Red White White Black ignition F Starter Switch To Charger Figure 5 NOTE The Operator s Manual that comes with the unit has a wealth of information regarding the setup operation and servicing of this unit NOTE This Service Manual is a supplement to the Operator s Manual IMPORTANT Please read understand and fol low all safety procedures listed in the Operator s Manual when working on this unit CAUTION Before servicing the unit place itona level surface turn off the engine and let the unit cool and disconnect the spark plug wire On electric start units make sure the key is in the off position 1 BLADE DRIVE BELT REMOVAL 1 1 Make sure the blade drive control is disen gaged 1 2 Using a inch socket remove the four screws securing the belt cover and removed the cover See Figure 6 Cover Screws 2 on each side Figure 6 1 3 Using a 2 inch socket remove the two screws attaching the flap bracket to the frame Remove the flap bracket See Figure 7 s i gt TE Mounting Screws 4A Flap Bracket View From Below Figure 7 Servicing the Troy Bilt Wide Cut 33 Combination Mower 1 4 Using
16. nce control lever to the left handlebar using a plastic tie or tape See Figure 19 gt Plastic Tie Figure 19 6 3 Engage the blade control lever to move the brake pad away from the drive pulley See Fig ure 20 Figure 20 Servicing the Troy Bilt Wide Cut 33 Combination Mower 6 4 Using a socket remove the Sems nuts and flat head screws securing the brake pad to the idler arm and remove the old brake pad See Figure 21 Figure 21 6 5 Loosely install the new brake pad 6 6 Release the operator presence control and allow the new brake pad to engage the sheave of the idler pulley See Figure 22 D a o seats 1 A ve a H y 4 fa T K Ba AA Figure 22 6 7 Tighten the Sems nut to secure the brake pad to the idler arm f WHEEL DRIVE BELT REMOVAL AND REPLACEMENT NOTE Some older units may not have all the belt guides installed 7 1 Release all mower controls 7 2 Using a 2 inch socket remove the two screws attaching the flap bracket to the frame Remove the flap bracket See Figure 23 ae ra es f T Figure 23 7 3 Using a 2 inch socket remove the four screws securing the belt cover and remove the cover 7 4 Temporarily remove the blade drive belt from around the engine pulley 7 5 Usea 9 16 inch socket to loosen the locknut securing the pulley and belt guide to the front idler bracket Remove the belt guide and pulley See F
17. sure that the V belt does not drag on the guide when engaged and that the lower portion of the guide is at least 1 8 inch away from the pulley 15 10 Use a vice to straighten the upper bend in the belt support bracket 1768381001 See Figure oa e A gt gt Belt Support Bracket A Upper bend straightened f Figure 65 18 Servicing the Troy Bilt Wide Cut 33 Combination Mower 15 11 Using a 2 inch by 1 4 20 bolt lock washer and contains all installation directions See Figure hex nut not supplied in kit attach the belt sup 67 port bracket to the top of the transaxle using the empty bolt hole at the left rear of the transaxle Older Style Guides a See Figure 66 gt Belt Support Brae AS WP 1 8 cleara ce A 7 Y S oe X gt Transaxle Pulle A r J y aF as es 2 Pivot Shat e j 7 Empty Bolt Hole F ie A Figure 67 NOTE The latest production of these units uses Figure 66 a newer flap bracket that integrates the belt guides into the metal stamping This newer flap bracket will NOT fit on older units NOTE The guide must be bent to clear the pivot shaft assembly while maintaining a distance of 1 8th inch of clearance from the transaxle pulley 16 ENGINE PULLEY BELT GUIDE KIT NOTE Some older units have a flap bracket that uses removable engine pulley belt guides Updated belt guides have been manufactured as
18. t parts Copyright 2005 MTD Products Inc All Rights Reserved MTD Products LLC Product Training and Education Department PRINTED IN USA FORM NO 769 00945 10 2003 Servicing the Troy Bilt Wide Cut 33 Combination Mower Servicing the Troy Bilt Wide Cut 33 Combination Mower Includes update Information for older models TROY BILT WIDE CUT MOWER The key switch is located on the right side of the con sole See Figure 2 Key Switch Figure 2 Model 12A E753B063 NEW 9 hp briggs amp Stratton I C OHV engine The unit also features an oversize fuel tank with a man Electric Start ual shutoff Mele ee Figure 3 o e 33 Deck ER ne y E7 Self Propelled Multiple Speed Gear Drive pa Peerless Transaxle BLade Brake Clutch e Automatic Parking Brake e Single Lever Height Adjustment e 3 in 1 Capacity The Model E753B features a standard size battery and electric start See Figure 1 Gas Tank Aa i i Fuel Shutoff aa va s Figure 3 Servicing the Troy Bilt Wide Cut 33 Combination Mower The fuse is located on the right side next to the battery and the solenoid is mounted on the battery support bracket under the battery See Figure 4 vill I gt A ha m use a la Solenoid Ke J gt _ v gt aN ANS DS 1 RIIN W Ff I AT ine _ I San a NS K N a i N ACELEA l Figure 4 Most electrica
19. ting Screw Belleville Washer Figure 39 12 8 Using a 1 2 inch socket remove the four mounting bolts securing the spindle to the deck See Fig ure 40 D Spindle Meunting Bolts 4 Figure 40 NOTE Hold the housing from underneath the deck when removing the final mounting bolt Remove the housing from the deck 12 9 Inspect the housing for excessive wear or dam age and replace as needed See Figure 39 12 10 Assembly is the reverse order of disassembly IMPORTANT During reassembly place Locktite 242 on the threads of the spindle pulley mount ing bolts and torque to 35 ft lbs If blades are removed also torque the blade mounting screws to 35 ft Ibs NOTE Time the blades properly during reas sembly Set the cutting blades perpendicular to each other during installation of the toothed drive belt See Figure 41 _ da gt pele Figure 41 13 LEFT SPINDLE REMOVAL 13 1 Using a inch socket remove the four screws securing the belt cover and removed the cover 13 2 Using a inch socket loosen the screw securing the belt tension adjustment bracket and turn it out of the way See Figure 42 a y A o q AR A 7 Pelt Tension Adjustment Bracke i N Figure 42 Servicing the Troy Bilt Wide Cut 33 Combination Mower 13 3 Align the sight holes in the right pulley with the spindle housing deck mounting bolts See Figure 43 fl fai Figure 43 13 4 Using a inch deep soc
20. vel ground adjust the blade cutting height to about 3 With the blade drive control disengaged set a gap of 1 8 between the spring and the flat washer on the end of the threaded portion of the lift crank by e the nut stil Figure 10 Figure 10 Servicing the Troy Bilt Wide Cut 33 Combination Mower 3 4 A With the engine OFF have a helper engage the blade drive Measure the distance between the center of the idler pulley and the left drive pulley The measurement should be between 5 1 2 and 5 5 8 See Figure 11 Hy SS Figure 11 NOTE If the blade drive belt slips during opera tion it may be necessary to slide the idler pulley forward in the slot on the idler arm Loosen the hardware on the idler pulley and slide the pulley forward slightly Tighten the hardware See Fig ure 8 IMPORTANT The blades must come to a com plete stop when the blade engagement lever is released BLADE DRIVE CONTROL LEVER ADJUST MENT NOTE Make the following adjustment if the blade drive control lever releases during opera tion 4 1 With the engine off engage the operator pres ence control and the blade drive control See Figure 12 Blade Drive Control L Operator Presence Control gt x N SS i a a a 4 SA Hairpin Clip yy SSSA fa eu a a Z7 F f J gt A iN z w na os Vn o j f j f f J H Y H Figure 12 4 2 Without releasing the
21. y 6 m Ve Figure 59 15 3 Reinstall the idler pulley onto the carriage bolt followed by the original flat washer the new belt guide 1760096 and secure it with the original lock nut See Figure 60 T Ta Idler Pulley Carriage Bolt Figure 60 NOTE Face the belt guide towards the front of the unit The flat washer must go between the Guide and the pulley in order to provide clear ance for the guide 15 4 Reinstall the belt guard cover 15 5 Using a 2 inch socket and extension remove the two flange screws that secure the flap bracket to the frame Remove the flap bracket and set it aside See Figure 61 a Figure 61 Servicing the Troy Bilt Wide Cut 33 Combination Mower 15 6 Using a 9 16 inch socket and extension remove the left rear engine mounting hex cap screw See Figure 62 ew Hidden above act Figure 62 15 7 Place the belt guide 1769522 in a vise and using a cold chisel open the eyelet until the hex Cap screws can pass through the opening See Figure 63 Hex Cap Screw Pry open N k W z wi Figure 63 15 8 Reinstall the hex cap screw through the frame and into the engine See Figure 64 Engine Mounting Hex Cap Screw Belt Guide 3 ow gt 4 3 Belt routing andremo CAIMEN aro portam Figure 64 15 9 Align the belt guide so that the V belt is on the inside and on top of the guide NOTE Make
Download Pdf Manuals
Related Search