WARNING: DO NOT START ENGINE!!!
Contents
1. Replace electrical box backing plate 4 bolts onto hull NOTE Apply blue Loctite to threads Do not over tighten bolts Install supplied billet ECU mounting bracket into electrical box using supplied hardware 4 M6 bolts NOTE Apply blue Loctite to bolts Do not over tighten At lower right side of electrical box cut and remove zip tie securing wiring harness to electrical box Follow harness and locate crank sensor connector black amp white wire black plug Install supplied cable splicer between connectors for black amp white wiring harness Connect stock ECU connectors 3 to Vi PEC V88R3 ECU NOTE Do not force Verify order location and orientation Listen feel for click when locked in place Secure RIVA ViIPEC ECU to ECU mounting bracket in electrical box supplied hardware 4 M4 bolts and washers NOTE Apply blue Loctite to bolts Do not over tighten w a CEFE WATERPROOF MARINE ECLI Secure wiring harness at lower right side of electrical box using supplied zip tie Replace electrical box cover Carefully slide into place so that wiring harnesses fit into cut out Secure electrical box cover 2 locking tabs at top At lower right side of electrical box tighten zip tie securing wiring harness to electrical box Inside front storage compartment remove rivets 5 securing service lid in place NOTE Press pin at center inward Word doc Part RY11840 ECU DC 1 MS 5 112. locate crank sensor connector black amp white wire black plug Install supplied cable splicer between connectors for black amp white wiring harness Connect stock ECU connectors 3 to Vi PEC V88R3 ECU NOTE Do not force Verify order location and orientation Listen feel for click when locked in place Secure RIVA ViIPEC ECU to ECU mounting bracket in electrical box using supplied hardware 4 M4 bolts and washers NOTE Apply blue Loctite to bolts Do not over tighten w a CEFE WATERPROOF MARINE ECLI Secure wiring harness at lower right side of electrical box using supplied zip tie Replace electrical box cover Carefully slide into place so that wiring harnesses fit into cut out Secure electrical box cover 2 locking tabs at top At lower right side of electrical box tighten zip tie securing wiring harness to electrical box Inside front storage compartment remove rivets 5 securing service lid in place NOTE Press pin at center inward Word doc Part RY11840 ECU DC 1 MS 5 11 15 Remove service lid and locate remote control sensor ay cof a A Era A ee 4 f a LAT lt s d D i ey a D gt amp E SS g 7 N v Disconnect electrical connector and install supplied block off into wiring harness connector NOTE Make sure block off snaps into place _ i Se _ _ lll _ _
3. 15 Remove service lid and locate remote control sensor ay cof a A Era A ee 4 f a LAT lt s d D i ey a D gt amp E SS g 7 N v Disconnect electrical connector and install supplied block off into wiring harness connector NOTE Make sure block off snaps into place _ i Se _ _ lll _ _ _ _ o _ o _ a _ _ o _ _ _ _ NOTE If a RIVA Vi PEC V88 ECU was previously installed you must swap the black block off with the supplied blue block off Secure bypass module to OEM wiring harness using supplied zip tie Replace service lid and secure using stock rivets Replace rear grab handle seat support if removed Reconnect battery cables NOTE Positive red first Negative black second Check bilge for tools rags etc NOTE ECU is equipped with our Stage 3 SVHO Base Map Verify required parts to run this map safely or download others by going to Click on Yamaha Click on V88R3 then click on Base Maps in the left navigation WARNING DONOTSTARTENGINE A Following the installation of your Pro Series ViPEC ECU you must perform ECU set up process using the Quick Start Guide available on the RIVA ViPEC ECU Manager Web Site Go to www riva vipec com gt Downloads to obtain Quick Start Guide Remember the wa
4. JAR EVA RACING PERFORMANCE EA amp MNES Vi PEC V88R3 Pro Series ECU PART RY11840 ECU DC 1 WATERPROOF m APPLICATION S Yamaha 1 8L Engine Models SVHO SHO HO We strongly recommend the use of a service manual to familiarize yourself with the various components and procedures involved with this installation These instructions have been written in step by step format and refer to illustrations Read through instructions entirely before performing installation Please follow these step by step instructions and illustrations carefully WARNING DO NOT START ENGINE A Following the installation of your Pro Series Vi PEC V88R3 ECU you must perform ECU set up process using the Quick Start Guide available on the RIVA ViPEC ECU Manager Web Site Go to www riva vipec com gt Downloads to obtain Quick Start Guide Word doc Part RY11840 ECU DC 1 MS 5 11 15 ViPEC V88R3 INSTALLATION INSTRUCTIONS Remove seats and rear storage bin Disconnect battery cables NOTE Negative black first Positive red second Remove rear grab handle seat support if equipped Remove electrical box cover 2 locking tabs at top Disconnect stock ECU 3 electrical connectors at bottom NOTE Document order of connectors Remove stock ECU 4 bolts Retain stock hardware 2010 08 FX SHO models only Proceed to page 6 and follow steps through completion of installation All other Yamaha 1 8L models contin
5. _ _ o _ o _ a _ _ o _ _ _ _ NOTE If a RIVA Vi PEC V88 ECU was previously installed you must swap the black block off with the supplied blue block off Secure bypass module to OEM wiring harness using supplied zip tie Replace service lid and secure using stock rivets Replace rear grab handle seat support if removed Reconnect battery cables NOTE Positive red first Negative black second Check bilge for tools rags etc NOTE ECU is equipped with our Stage 3 SVHO Base Map Verify required parts to run this map safely or download others by going to Click on Yamaha Click on V88R3 then click on Base Maps in the left navigation A WARNING DO NOT START ENGINE A Following the installation of your Pro Series ViPEC ECU you must perform ECU set up process using the Quick Start Guide available on the RIVA ViPEC ECU Manager Web Site Go to www riva vipec com gt Downloads to obtain Quick Start Guide Remember the water belongs to everyone Please ride responsibly and respect the environment Technical Support For answers to questions regarding installation or trouble shooting RIVA Performance Products contact RIVA Technical Support directly at 954 247 0705 or by e mail at tech _support rivamotorsports com Limited Warranty RIVA Vi PEC Pro Series ECU s carry a 1 year limited warranty to the original pu
6. f merchantability and fitness for a particular purpose applies Various states do not allow for the limitation of incidental or consequential damages and therefore the above exclusion or limitation may not apply to you Warranty does not include the expenses related to freight or transportation of parts or compensation for any inconvenience or loss of use while being repaired A copy of the original invoice and a Return Authorization Number RA must accompany all warranty claims Warranted replacement parts will be returned freight collect Word doc Part RY11840 ECU DC 1 MS 5 11 15 8
7. oice and a Return Authorization Number RA must accompany all warranty claims Warranted replacement parts will be returned freight collect Word doc Part RY11840 ECU DC 1 MS 5 11 15 5 2010 08 FX SHO Models ONLY INSTALLATION INSTRUCTIONS Remove mounting tab on right side of relay box backing plate Remove ECU electrical box 4 bolts from hull Disconnect Slant Detection Switch Remove electrical system relay box 2 bolts from electrical box Install relay box backing plate onto electrical box backing with one original bolt Push relay box backing plate towards bolt check to make sure it s level and then secure Locate and drill 1 4 hole through electrical box backing Remove electrical box backing plate from hull and set plate aside Remove relay box backing plate from electrical box Word doc Part RY11840 ECU DC 1 MS 5 11 15 6 Replace relay box backing plate onto relay box using only 5 original bolts NOTE Apply blue Loctite to threads Do not over tighten bolts Do not use i al Replace relay box onto electrical box backing plate using one original bolt At opposite side use supplied M6 bolt washer and spacer to secure relay box to electrical box NOTE Apply blue Loctite to threads Do not over tighten bolts Place supplied spacer between S relay box and electrical box securing relay box to electrical Word doc Part RY11840 ECU DC 1 MS 5 11 15
8. rchaser They are warranted to be free of defects in materials and workmanship under normal use and service Customer modified components will be void of warranty This warranty is limited to defects in the primary components only Finish and or wear marks in or on primary components are not covered under this warranty RIVA Racing s liability is expressly limited to the repair or replacement of the components contained within or associated with this kit RIVA Racing agrees to repair or at RIVA s option replace any defective unit without charge if product is returned to RIVA Racing freight prepaid within the warranty period Any equipment returned which in RIVA s opinion has been subjected to misuse abuse overheating or accident shall not be covered by this warranty RIVA Racing shall have no liability for special incidental or consequential damages or injury to persons or property from any cause arising from the sale installation or use of this product No other warranty express or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose applies Various states do not allow for the limitation of incidental or consequential damages and therefore the above exclusion or limitation may not apply to you Warranty does not include the expenses related to freight or transportation of parts or compensation for any inconvenience or loss of use while being repaired A copy of the original inv
9. ter belongs to everyone Please ride responsibly and respect the environment Technical Support For answers to questions regarding installation or trouble shooting RIVA Performance Products contact RIVA Technical Support directly at 954 247 0705 or by e mail at tech _support rivamotorsports com Limited Warranty RIVA Vi PEC Pro Series ECU s carry a 1 year limited warranty to the original purchaser They are warranted to be free of defects in materials and workmanship under normal use and service Customer modified components will be void of warranty This warranty is limited to defects in the primary components only Finish and or wear marks in or on primary components are not covered under this warranty RIVA Racing s liability is expressly limited to the repair or replacement of the components contained within or associated with this kit RIVA Racing agrees to repair or at RIVA s option replace any defective unit without charge if product is returned to RIVA Racing freight prepaid within the warranty period Any equipment returned which in RIVA s opinion has been subjected to misuse abuse overheating or accident shall not be covered by this warranty RIVA Racing shall have no liability for special incidental or consequential damages or injury to persons or property from any cause arising from the sale installation or use of this product No other warranty express or implied including but not limited to the implied warranties o
10. ue this page Word doc Part RY11840 ECU DC 1 MS 5 11 15 2015 amp Newer Models Disconnect wire leads from start relay Note Document position of wire leads Remove bolts 4 securing electrical panel to bulkhead Lift up electrical panel and set on bulkhead Remove bolts 2 securing start relay to electrical panel Remove lower right bolt on fuse panel Remove Bolts M Install top hole of start relay bracket in lower right bolt position of fuse panel Secure with original bolt Do not tighten bolt yet Position start relay bracket straight up down Using a B size drill bit slide drill bit through relay bracket straight down and mark the hole location in the electrical panel see illustration below Rotate relay bracket out of the way amp complete drilling the hole Rotate relay bracket in position amp secure with supplied M6 bolt spacer washers 2 and nylon lock nut Tighten both relay bracket bolts Old Relay Location Reinstall electrical panel to bulkhead Reinstall wire leads to starter relay All Year Models Continue from this point Install supplied billet ECU mounting bracket into electrical box using supplied hardware 4 M6 bolts NOTE Apply blue Loctite to bolts Do not over tighten Word doc Part RY11840 ECU DC 1 MS 5 11 15 At lower right side of electrical box cut and remove zip tie securing wiring harness to electrical box Follow harness and
Download Pdf Manuals
Related Search