The original air compressor is driven by the bull gear and
Contents
1. ECTIVE AIR COMPRESSOR REPLACE INSERT NEW GASKET INSTALL Figure 10 14 Flowchart for Replacement of the Original type Air Compressor All information subject to change without notice 10 12 From Bulletin 9 60 02 6SE483 0204 Copyright 2002 DETROIT DIESEL CORPORATION2. SERIES 60 SERVICE MANUAL The original air compressor is driven by the bull gear and water cooled Engine coolant is fed to the compressor through a flexible hose tapped into the engine block water jacket and connected to the front of the compressor Coolant returns from the rear of the compressor through a flexible hose to the engine cylinder head Lubricating oil is supplied to the compressor by a line from the cylinder block oil gallery that connects to the air compressor Lubricating oil returns to the engine crankcase through the air compressor drive assembly NOTE An air compressor oil test card DD5524 is available to test engine mounted air compressors for excessive oil leakage Contact an authorized Detroit Diesel service outlet for details The current adaptorless air compressors have replaced the original air compressors and adaptors on the majority of Series 60 on highway engines This change took effect with unit serial number 6R210293 built November 30 1994 The original compressor and adaptor are available on certain on highway and industrial models due to customer preference An optional 28 cfm twin cylinder air compressor has replaced the former optional 31 cfm four cylinder air compressor starting with model year 1999 The 28 cfm high output air compressor is a naturally aspirated design that requires the intake air to be plumbed from the clean air side of the air filter Both high output air compressors require the engin
3. ar adequate eye protection face shield or safety goggles Install the hose clamps onto the hoses Install the coolant supply and return lines and connect them to the air compressor Install the lubricating oil supply line to the air compressor Install the air lines to and from the compressor Refer to section 2 6 6 and install the air compressor driven fuel pump Refer to section 13 13 4 and fill the cooling system Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer birth defects and other reproductive harm Always start and operate an engine in a well ventilated area If operating an engine in an enclosed area vent the exhaust to the outside Do not modify or tamper with the exhaust system or emission control system Start the engine and check for leaks All information subject to change without notice 6SE483 0204 Copyright 2002 DETROIT DIESEL CORPORATION From Bulletin 9 60 02 10 11a 10 1 AIR COMPRESSOR VEHICLE APPLICATIONS ONLY 10 1 4 Replacement of the Original type Air Compressor Detroit Diesel does not service the original type air compressor Service of the original type air compressors should be referred to an authorized service center of the original equipment manufacturer To replace the original type air compressor perform the following procedure See Figure 10 14 REMOVE AND CLEAN AIR COMPRESSOR INSPECT AIR COMPRESSOR DEF
4. e driven fuel pump to be mounted to the gear case above the air compressor For Series 60 2002 Exhaust Gas Recirculation EGR engine a naturally aspirated single cylinder reciprocating compressor with a rated displacement of 13 cubic feet per minute at 1250 RPM is used The engine provides a continuous supply of oil to the compressor Oil is routed from the oil passage in the gear case to the compressor oil inlet All information subject to change without notice 6SE483 0204 Copyright 2002 DETROIT DIESEL CORPORATION From Bulletin 9 60 02 10 5 10 1 AIR COMPRESSOR VEHICLE APPLICATIONS ONLY Current adaptorless air compressors are similar to the original compressors except that their mounting flanges have been redesigned to permit direct installation of the compressor onto the gear case The drive gear stackup on this compressor has been modified to eliminate the need for a drive adaptor See Figure 10 10 ADAPTOR MOUNTED ADAPTORLESS AIR AIR COMPRESSOR COMPRESSOR DRIVE ADAPTOR 364 mm 237 2 mm 14 33 in 9 34 in ORIGINAL CURRENT AND CURRENT STANDARD 28 CFM Figure 10 10 Original Adaptor Current 28 CFM mounted and Current Adaptorless Air Compressor NOTE If information is required to service an original air compressor refer to section 10 1 8 All information subjec
5. horized service center of the original equipment manufacturer To replace the adaptorless air compressor perform the following procedure See Figure 10 12 REMOVE AND CLEAN AIR COMPRESSOR INSPECT AIR COMPRESSOR DEFECTIVE AIR COMPRESSOR REPLACE INSERT NEW GASKET INSTALL Figure 10 12 Flowchart for Replacement of Adaptorless Air Compressor All information subject to change without notice 6SE483 0204 Copyright 2002 DETROIT DIESEL CORPORATION From Bulletin 9 60 02 10 8 10 1 AIR COMPRESSOR VEHICLE APPLICATIONS ONLY 10 1 2 Cleaning and Removal of Adaptorless Air Compressor Precleaning is not necessary Remove the adaptorless air compressor as follows 1 Disconnect the air lines to and from the compressor Disconnect the fuel pump lines Remove the fuel pump and drive coupling Refer to section 2 6 2 Drain the cooling system Refer to section 13 13 4 Disconnect and drain the coolant supply and return lines at the air compressor Disconnect the lubricating oil supply line from the compressor BC SNe Ste ee coe at Remove the bolts securing the air compressor support bracket to the cylinder block and air compressor 8 Remove the support bracket NOTE Due to the cylinder block and compressor configuration the upper inside air compressor to air compressor drive bolt is difficult to reach with standard tools Compressor Wrench J 35948 will fac
6. ilitate removal and installation of this bolt 9 Remove the five bolts and one nut that secure the air compressor to the gear case 10 For Series 60 2002 EGR Single Cylinder Air Compressor remove the five bolts that secure the air compressor to the gear case 11 Slide the air compressor rearward to disengage the hub from the coupling 10 1 2 1 Inspection of Adaptorless Air Compressor Refer to OEM guidelines to determine if the air compressor needs to be repaired or replaced All information subject to change without notice 10 9 From Bulletin 9 60 02 6SE483 0204 Copyright 2002 DETROIT DIESEL CORPORATION SERIES 60 SERVICE MANUAL 10 1 3 Installation of Adaptorless Air Compressor Install the adaptorless air compressor as follows 1 Clean all gasket material from the mating surfaces of the air compressor and the gear case 2 Align the reference mark on the fuel pump drive coupling to the nine o clock position This will set the air compressor piston at top dead center and will help to ease the process of checking gear lash 3 Using a new gasket and bolts and nut previously removed install the air compressor to its original location on the gear case NOTE The shorter bolt is installed in the two o clock position and the nut is installed in the twelve o clock position 4 For torquing sequence see Figure 10 13 Use compressor wrench J 35948 to torque the upper inside bolt Using the bolt and nut torquing sequence torque fi
7. t to change without notice 10 6 From Bulletin 9 60 02 6SE483 0204 Copyright 2002 DETROIT DIESEL CORPORATION SERIES 60 SERVICE MANUAL 1111110 AWS I LISS CQ piyi 190 0 mm 7 48 in pe 43089 2 Single Cylinder Air Compressor 1 Gear Case Figure 10 10a Series 60 2002 Single Cylinder Air Compressor 13 CFM From Bulletin 9 60 02 10 6a All information subject to change without notice 6SE483 0204 Copyright 2002 DETROIT DIESEL CORPORATION 10 1 AIR COMPRESSOR VEHICLE APPLICATIONS ONLY The current Series 60 adaptorless air compressor is flange mounted to the rear of the gear case located on the left side of the engine See Figure 10 11 HIGH PRESSURE FUEL PUMP AIR COMPRESSOR Figure 10 11 Adaptorless Air Compressor Mounting Current adaptorless air compressors also drive the engine fuel pump which is bolted to the rear end of the compressor The compressor crankshaft is designed to accept a drive coupling placed between the compressor and fuel pump All information subject to change without notice 10 7 From Bulletin 9 60 02 6SE483 0204 Copyright 2002 DETROIT DIESEL CORPORATION SERIES 60 SERVICE MANUAL 10 1 1 Replacement of Adaptorless Air Compressor Detroit Diesel does not service the adaptorless air compressor Service of an adaptorless air compressor should be referred to an aut
8. ve bolts and one nut to 58 73 N m 43 54 lb ft Figure 10 13 Bolt Torque Sequence All information subject to change without notice 6SE483 0204 Copyright 2002 DETROIT DIESEL CORPORATION From Bulletin 9 60 02 10 10 10 1 AIR COMPRESSOR VEHICLE APPLICATIONS ONLY 43096 Figure 10 13a Bolt Torque Sequence Series 60 2002 Single Cylinder Air Compressor 5 For torque sequence for Series 60 2002 EGR Single Cylinder Air Compressor see Figure 10 13a Torque five bolts to 58 73 N m 43 54 lb ft 6 Refer to section 1 21 2 1 step 15 and check the bull gear to air compressor drive gear lash measurement 7 Refer to section 1 21 2 1 step 15 and install the power steering pump drive coupling power steering pump and cover assembly to the gear case cover 8 Install the improved air compressor support bracket to the compressor and cylinder block as follows a Tighten the support bracket to air compressor bolts For 25 mm long bolts use a torque of 41 52 N m 30 38 lb ft For 20 mm long bolts use a torque of 30 38 N m 22 28 lb ft b Torque the support bracket to cylinder block bolts to 58 73 N m 43 54 lb ft All information subject to change without notice 10 11 From Bulletin 9 60 02 6SE483 0204 Copyright 2002 DETROIT DIESEL CORPORATION 10 11 12 13 14 SERIES 60 SERVICE MANUAL To avoid injury from flying parts when working with components under spring tension we
Download Pdf Manuals
Related Search