Installation & Operation Manual
Contents
1. Terminal Block o DUAL VOLT TOGGLE SWITCH ITCB DV HV ITCB DV HV TWIN ELECTRICAL HOOK UP Models CAUTION Improper electrical installation will damage electronic components Damage caused by incor rect electrical connections is not covered by warranty An electrician must provide electrical service Determine the available on site electrical service Steps 3 amp 9 apply to DV models only Select the desired unit voltage based on the available on site elec trical service Using a voltmeter check the voltage and color coding of each conductor at the electrical source Remove the front panel to gain access to the terminal block Feed the power cord through the strain relief and connect it to the terminal block Connect the power cord to the terminal block as shown Before proceeding verify the voltage at the field wiring terminal block Set voltage switch to the appropriate position and replace the access panel 0 If plumbing is to be hooked up later be sure the brewer is disconnected from the power source If plumb ing has been hooked up the brewer is ready for Initial Set Up 6 36748 3 041714 pm CE Requirements This appliance must be installed in locations where it can be overseen by trained personnel For proper operation this appliance must be installed where the temperature is between 5 C to 35 C Appliance shall not be tilted more than 102. 2 3 User 4 Electrical Requirements TB TGB DY 5 Electrical Requirements ITGB DV HV ATWIN 6 Plumbing Requirements Optional 7 Operating 8 MC 9 T 10 10 Cleaning Tank 11 Sanitizing Optional SUWBBIGHOI oie rie EE dp emer tries 12 Programming etus ase p oae 15 je E RT __ 120V Infusion Tea Brewer 220 Volt Brewer ME UM MEM E CE UE Dual Dilution Ini c CE Low Profile Machine Dual Voltage Dual Voltage High Volume Dual Voltage Brewer for Canada 230 Volt Brewer MOBB 200 Volt Brewer p e WHERE 2 Brew Stations 3 36748 3 100114 USER NOTICES Carefully read and follow all notices in this manual and on the equipment All labels on the equipment should be kept in good condition Replace any unreadable or damaged labels As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food
3. Models with factory installed sweetener 8 Press and hold the left hidden switch until the display reads SanitizeSweetnr Press YES Next screen will ask CONTAINER READY 9 Press YES Allow solution to flow from dilution nozzle for a few seconds 10 Press any brew switch to stop Display will read SOAKING and count down from 15 minutes Display will now read SOAP PURGE 11 Remove the special sanitizing fittings or empty cut 1 fittings from the 1 disconnects QCD s and re connect the QCD fittings to the appropriate container You will now begin the process of bringing syrup back through the system a Place empty tea dispenser under unit b Place empty brew basket into funnel rails 12 Press START Next screen will ask CONTAINER READY 13 Press YES Continue with brew cycle until syrup is flowing freely from the dilution nozzle 14 Press any brew switch to stop Display will read SANITAION COMPLETE and return to home screen Models with field installed sweetener kit 8 The next steps are to initiate a brew cycle and draw sanitizer through the system a Place empty tea dispenser under unit b Place empty brew basket into funnel rails c Push appropriate brew button for Sweet Tea brew cycle will initiate d Continue with brew cycle until the sanitizing solution is flowing from the dilution nozzle e Push the Enable Brew on off button to stop the brew cycle and then push aga
4. for safe operation An electrician must provide electrical service as specified in conformance with all local and national codes This appliance must not be cleaned by water jet This appliance is not intended for use by persons including children with reduced physical sensory or mental Capabilities or lack of experience and knowledge unless they have been given instructions concerning use of this appliance by a person responsible for its safety Children should be supervised to ensure they do not play with the appliance f the power cord is ever damaged it must be replaced by the manufacturer or authorized service personnel with a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard Machine must not be immersed for cleaning PLUMBING REQUIREMENTS These brewers must be connected to a cold water system with operating pressure between 20 and 90 psi 138 and 620 kPa from a 1 2 or larger supply line A shut off valve should be installed in the line before the brewer Install a regulator in the line when pressure is greater than 90 psi 620 kPa to reduce it to 50 psi 345 kPa The water inlet fitting is 75 11 5 NH HOSE THREAD For convenience an elbow adaptor is provided to convert to a 1 4 flare fitting 3 8 flare on Twins Bunn O Matic does not recommend the use of a reverse osmosis deionized water supply to this equipment REQUIRED 1 25 gpm 4 73 Ipm flow ra
5. amp HV ON OFF ON OFF BREW 1 BREW ITCB TWIN HV a ENABLE ENABLE Y ON OFF ON OFF BREW BREW SERIES Brewer Control a Right Programming hidden switch just to the right of the display This is used to access the program ming mode and is also used to scroll forward through the function list b Left Programming hidden switch just to the left of the display This is used to scroll backwards through the function list c Brew A B C Digital Brewer Control Twins Only Used to select options that appear on the display during programming 13 36748 3 111010 PROGRAMMING THE BREWER The programming of the brewer is divided into two levels There is one function in Level 1 All other functions are accessed in Level 2 The following function screens are in order of appearance Each screen will have instructions on how to access and the procedures to program the various functions of the brewer IMPORTANT PROGRAMMING NOTES READ CAREFULLY To exit the programming mode at any time press and release the ON OFF pad located on the front switch panel The display will return to the MAIN SCREEN If none of the five programming switches are pressed within one minute during the setup of the brewer the programming of the function screen that is being set will be exited and the display will return to the MAIN SCREEN Always remember to place a container and funnel under the sprayhead when operating
6. Pour O Matic BUNN BUNN with the stylized red line BUNNlink Bunn OMatic Bunn O Matic BUNNserve BUNNSERVE with the stylized wrench design Cool Froth DBC Dr Brew stylized Dr design Dual Easy Pour EasyClear EasyGard FlavorGard Gourmet Ice Gourmet Juice High Intensity iMIX Infusion Series Intellisteam My Caf Phase Brew PowerLogic Quality Beverage Equipment Worldwide Respect Earth Respect Earth with the stylized leaf and coffee cherry design Safety Fresh savemycoffee com Scale Pro Silver Series Single Smart Funnel Smart Hopper SmartWAVE Soft Heat SplashGard The Mark of Quality in Beverage Equipment Worldwide ThermoFresh Titan trifecta TRIFECTA sylized logo Velocity Brew Air Brew Beverage Bar Creator Beverage Profit Calculator Brew better not bitter Build A Drink BUNNSource Coffee At Its Best Cyclonic Heating System Daypart Digital Brewer Control Element Milk Texturing Fusion Nothing Brews Like a BUNN Picture Prompted Cleaning Pouring Profits Signature Series Sure Tamp Tea At Its Best The Horizontal Red Line Ultra are either trademarks or registered trademarks of Bunn O Matic Corporation The commercial trifecta brewer housing configura tion is a trademark of Bunn O Matic Corporation 2 36748 3 031314 INTRODUCTION ITB This equipment will brew tea into an awaiting dispenser or reservoir The ITB uses recipe settings to brew tea It has an LCD for digital readout and programming The user
7. the brewer during the set up of CALIBRATE FLOW and testing the brew and dilution valves in SERVICE TOOLS TEST OUTPUTS MAIN SCREEN This screen will be shown when the brewer is ready for use The screen displays the water temperature in the tank When the water in the tank reaches the correct set temperature the display will change from HEATING to READY TO BREW Dese Brewer Contro UNLOCK tk PROGRAMMING LOCKOUT SWITCH ITCB located on the memory module board prior to ITCB HV S N ICB0007479 located on the main control board S N 1CB0007479 and after ITB located on the main control board LOCK PROGRAMMING LOCKOUT SWITCH This switch can be set to prevent access to the programming settings of the brewer Once all the cor rect brew Settings are programmed the operator can set the switch to the position to prohibit anyone from changing the settings With the switch in the ON position the programming menus can still be accessed to view the current settings However no changes will be saved ITB ONLY NOTE ITB Switches A B amp C are not used 14 36748 3 111010 ITB PROGRAMMING FUNCTIONS FLOW CHART PROGRAMMING FUNCTIONS LEVEL Desa Brewer PROGRAMMING FUNCTIONS LEVEL 2 Digitar Brewer Controt Digital Brewer Controt Digitar Brewer Control Digitar Brewer Control Brewer Brewer Control Brewer
8. 4 Slide the funnel into the funnel rails The brewer will read the coffee name and size ground through the chip in the funnel handle NOTE The brewer will automatically match the brew batch size to the grinder batch size GRINDER BREWER Small Half Batch Medium Full Batch Large Full Batch f BREW is pressed with a large grinder batch the display will read INCORRECT GRIND BATCH SIZE WRONG and then PRESS BREW BREW ANYWAY 5 Place an empty server under the funnel 6 The ON OFF must be ON 7 Momentarily press and release the assigned BREW switch There may be certain situations in which the brew cycle will not begin when BREW is pressed a SWITCH NOT ON ON OFF must be ON b BREW TEMPERATURE TOO LOW wait until heated or cancel BREW LOCKOUT option CHECK FUNNEL remove funnel empty previously brewed grounds and replace with fresh d INCORRECT GRIND Indicates a large batch was ground using the grinder Check batch size and grind weight 8 If none of the above messages are displayed the display will read NOW BREWING and show the time remain ing in the brew cycle 9 Following the brew will be a countdown of drip time DRIPPING which shows the time remaining until the coffee no longer drips from the funnel tip 10 Carefully remove the brew funnel and discard the grounds and filter only after visible dripping stops CLEANING CAUTION CLEAN AND SANITIZE YOUR ICED TEA BREWER DAILY 1 Remove and thoroughly cle
9. CANTER IF CRACKED SCRATCHED 00824 0002 WHEN EMPTY USED ON HIGH FLAME FUNNEL CONTENTS on EXPOSED ELECTRIC ARE HOT ELEMENTS READ THE ENTIRE OPERATING BEFORE USING THIS PRODUCT FAILURE TO COMPLY RISKS INJURY 00658 0000 To reduce the risk of electric shock do not remove or open cover No user serviceable parts inside Authorized service personnel only Disconnect power before servicing 37881 0000 REMOVE FUNNEL SLOWLY 03408 0000 REH 03409 0000 Fill water tank before turning on thermostat or connecting appliance to power source Use only on a properly protected circuit capable of the rated load Electrically ground the chassis Follow national local electrical codes Do not use near combustibles FAILURE TO COMPLY RISKS EQUIPMENT DAMAGE FIRE OR SHOCK HAZARD READ THE ENTIRE OPERATING MANUAL BEFORE BUYING OR USING THIS PRODUCT THIS APPLIANCE IS HEATED WHENEVER CONNECTED TO A POWER SOURCE 00831 0000F 3 98 1998 BUNN O MATIC CORPORATION 00831 0000 ITB 4 and aligned with Make sure Funnel is rotated an el is rotate ake sure uis the RIGHT side to avoid Tea Dispenser on the LEFT aligned with Tea 015 qudm and water spills potential burns and Water spills O avoid tial bu TIL poten __ 41995 0000 ITB DD 4 36748 3 112912 ELECTRICAL REQUIRE
10. Des Brewer Control Digitar Brewer Control Digitar Brewer Digitar Bewer Control eee ee Brewer Conor Desa Brewer Contror Brewer Control Digital Brewer Control Digital Brewer Control Digital Brewer Digital Brewer Control 15 36748 3 111010 Deiat Brewer Control ITCB PROGRAMMING FUNCTIONS FLOW CHART PROGRAMMING FUNCTIONS LEVEL Brewer Controt PROGRAMMING FUNCTIONS LEVEL 2 Digitar Brewer Control Digital Brewer Contror Digital Brewer Control Digitar Bewer Contror Brewer Control Brewer Control Brewer Contro Digitar Brewer Controt Digitar Brewer Conor Digitar Bewer Control Brewer ee Brewer Control Digital Brewer Controt Brewer Control Digital Brewer Control Digital Brewer Control Brewer Controt Dena Brewer Brewer Control Digital Control 16 36748 3 111010 ITCB DV HV PROGRAMMING FUNCTIONS FLOW CHART PROGRAMMING FUNCTIONS LEVEL aes Desa Brewer Control PROGRAMMING FUNCTIONS LEVEL 2 Brewer Control Digital Brewer Control Brewer Control Brew er Control Brewer Conor Desa Brewer Brewer Control Brewer Control Digital Brewer Control Digitar Brewer Control Br
11. ITBATCB ITCB DV HV ITCB TWIN HV Infusion Series INSTALLATION amp OPERATING GUIDE BUNN O MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD ILLINOIS 62708 3227 PHONE 217 529 6601 FAX 217 529 6644 www bunn com To ensure you have the latest revision of the Operating Manual or to view the Illustrated Parts Catalog Programming Manual or Service Manual please visit the Bunn O Matic website at www bunn com This is absolutely FREE and the quickest way to obtain the latest catalog and manual updates For Technical Service contact Bunn O Matic Corporation at 1 800 286 6070 0 5 36748 0003E 10 14 2010 Bunn O Matic Corporation BUNN 0 MATIC COMMERCIAL PRODUCT WARRANTY Bunn O Matic Corp BUNN warrants equipment manufactured by it as follows 1 Airpots thermal carafes decanters GPR servers iced tea coffee dispensers MCR MCP MCA single cup brewers ther mal servers and ThermoFresh servers mechanical and digital 1 year parts and 1 year labor 2 All other equipment 2 years parts and 1 year labor plus added warranties as specified below 8 Electronic circuit and or control boards parts and labor for 3 years b Compressors on refrigeration equipment 5 years parts and 1 year labor c Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis parts and labor for 4 years or 40 000 pounds of coffee whichever comes first These warranty
12. MENTS ITB amp ITCB DV Refer to Data Plate on the Brewer and local national electrical codes to determine circuit requirements Optional Field Wiring ratings are located on the machine near the dataplate WARNING The brewer must be disconnected from the power source until specified WARNING The power cord must be UL Listed Flexible Cord Type SO SJO SJTO HSJO or SJOW Rated 90 C and the attachment plug cap must be UL Listed in order to avoid a hazard The Power Supply Cord must be at least 3 feet long and maximum 6 feet long measured from Strain Relief to end of the Attachment Plug Cap ITB 120V models require 2 wire grounded service rated 120 volts AC 15 amp single phase 60Hz POWER CORD POWER CORD ITCB DV ONLY DUAL VOLT TOGGLE SWITCH 220 240V 2 WIRE GROUND ELECTRICAL HOOK UP Models CAUTION Improper electrical installation will damage electronic components Damage caused by incor rect electrical connections is not covered by warranty Anelectrician must provide electrical service Determine the available on site electrical service Steps 3 amp 9 apply to DV models only Select the desired unit voltage based on the available on site elec trical service Using a voltmeter check the voltage and color coding of each conductor at the electrical source Remove the back panel to gain access to the terminal block Feed the power cord through the strain reli
13. an the entire brew funnel The funnel tip and screen must be free from any tea particles or residue Reassemble the funnel 2 Remove and thoroughly rinse the sprayhead The holes must be open and clear of any mineral deposits Wipe the sprayhead panel clean with a damp cloth NOTE Any buildup on the sprayhead may restrict water flow and impact your brewing For consistently great tea and coffee clean sprayhead weekly with sprayhead cleaning tool 38227 0000 Upon visual inspection it may appear that light passes through all holes in the sprayhead but a thin film of residue can pass light and still impede water flow a Remove sprayhead from brewer b Use the pointed end of sprayhead cleaning tool to remove any mineral deposits from the sprayhead holes c Insert the long end of sprayhead cleaning tool into the sprayhead fitting and rotate several times to remove any mineral deposits from the fitting 3 The use of a damp cloth rinsed in any mild nonabrasive liquid detergent is recommended for cleaning all surfaces on Bunn O Matic equipment Do NOT clean this equipment with a water jet device CAUTION DO NOT KEEP BREWED ICED TEA OVERNIGHT THE SERVER MUST BE CLEANED DAILY TANK DRAIN 1 Remove back access cover front cover on HV 2 Close the white shutoff clamp on the long hose between tank and inlet solenoid 3 Disconnect the hose clamp and hose from inlet solenoid or check valve 4 Place the end of the drain hose in a container
14. and Drug Administration FDA this equipment must be installed with adequate backflow prevention to comply with federal state and local codes For models installed outside the U S A you must comply with the applicable Plumb ing Sanitation Code for your area 00656 0001 DO NOT OVERLOAD CIRCUIT ALWAYS ELECTRICALLY GROUND THE CHASSIS DO NOT DEFORM PLUG OR CORD FOLLOW NATIONAL AND LOCAL ELECTRICAL CODES KEEP COMBUSTIBLES AWAY FAILURE TO COMPLY RISKS EQUIPMENT DAMAGE FIRE OR SHOCK HAZARD READ THE ENTIRE OPERATING MANUAL BEFORE USING THIS PRODUCT 00986 0000 10 07 1994 Bunn O Matic Corporation 00986 0000 ITCB For 120 208V or 120 240 volt operation replace Power Supply Cord only with Bunn O Matic part number 01699 0000 34072 0000 ITCB Incorrect programming could result in accidental dispens ing of HOT LIQUID Trained personnel are to follow instructions provided for software programming Use of additional graphic layer requires disabling of appropriate switches Read all instructions for additional graphic layer prior to installing and programming TENTS 39175 0000 Risk of Fire Use a UL listed grounding type attachment plug rated 125 250 Vac 30 A 1 phase 4 conductor Plug to be selected and installed only by qualified service personnel 38125 0000 04 05 2005 Bunn O Matic Corporation 38125 0000 TWIN DISCARD DE
15. ef and connect it to the terminal block s Connect the power cord to the terminal block as shown Before proceeding verify the voltage at the field wiring terminal block Set voltage switch to the appropriate position and replace the access panel 0 If plumbing is to be hooked up later be sure the brewer is disconnected from the power source If plumb ing has been hooked up the brewer is ready for Initial Set Up CON O02 Soro 5 36748 3 041714 ELECTRICAL REQUIREMENTS ITCB DV HV amp TWIN Refer to Data Plate on the Brewer and local national electrical codes to determine circuit requirements Optional Field Wiring ratings are located on the machine near the dataplate WARNING The brewer must be disconnected from the power source until specified WARNING The power cord must be UL Listed Flexible Cord Type SO SJO SJTO HSJO or SJOW Rated 90 C and the attachment plug cap must be UL Listed in orderto avoid a hazard The Power Supply Cord must be at least 3 feet long and maximum 6 feet long measured from Strain Relief to end of the Attachment Plug Cap ITCB HV TWIN requires 3 wire grounded service rated 120 208 240 volts AC 30 amp single phase 60Hz ITCB DV HV 120V models require 2 wire grounded service rated 120 volts AC 15 amp single phase 60Hz or 3 wire grounded service rated 120 208 240 volts AC 20 amp single phase 60Hz ITCB DV HV amp TWIN ITCB DV HV ONLY POWER CORD POWER CORD
16. ewer Control Brewer Control Deme Brewer Control Desa Brewer Contror Brewer Brewer Control Digital Brewer Control Digitar Brewer Control Digitar Brewer Control Desa Brewer Controt Digital Brewer Contror Digital Brewer Controt 17 36748 3 111010 ITCB HV TWIN PROGRAMMING FUNCTIONS FLOW CHART PROGRAMMING FUNCTIONS LEVEL Desa Brewer Control PROGRAMMING FUNCTIONS LEVEL 2 Brewer Controt Brewer Control Brewer Brewer Control Deme Brewer Conor Digital Brewer Control Digitar Brewer Brewer Contror Digitat Brewer Control Digital Brewer Control Deme Brewer Control Digital Brewer Contro ee ee 3 Brewer Control Digital Brewer Control Dena Brewer Brewer Control Digital Brewer Control Brewer Brewer Digital Brewer Control Brewer Control Digital Brewer Control Brewer Control Brewer Control Desa Brewer Contro Brewer Control 18 36748 3 111010
17. in to cancel the brew cycle f Allow sanitizer to remain in lines for fifteen 15 minutes 9 Remove the special sanitizing fittings or empty cut fittings from the 1 disconnects QCD s and re connect the QCD fittings to the appropriate container You will now begin the process of bringing syrup back through the system a Place empty tea dispenser under unit b Place empty brew basket into funnel rails c Push appropriate brew button for Sweet Tea brew cycle will initiate d Continue with brew cycle until syrup is flowing freely from the dilution nozzle You may need to repeat steps a through d until syrup is dispensing from the dilution nozzle 12 36748 3 111010 PROGRAMMING Using the menu driven display on the front of the brewer the operator has the ability to alter or modify various brewing parameters such as brew temperatures brew volumes dilution volumes pulse brew etc This allows for the precise brewing of various flavors of tea and coffee Programming of the brewer is achieved by entering a certain function Then by the use of hidden programming switches and the brew function switches the operator can customize the brewing process to their specifications PROGRAMMING SWITCHES To access the programming mode and to scroll through the different function screens hidden programming switches are used There are five of these switches that will be used for the setup of the brewer ITB ITCB DV
18. is able to select regular or quick brew for tea programming Other features include Pre Infusion and Pulse Brew quick and standard brew Energy Savings mode BUNNLink compatible Freshness Timer Sanitation Alert and brew counters Available in low profile dual dilution and sweetener models ITCB DV ITCB DV HV This equipment will brew either tea or coffee into an awaiting dispenser or reservoir It can be easily configured for 120V or 120 208V 120 240V Refer to data plate for specific ratings The brewer may have an auxiliary hot water faucet that can be mounted on the front left or right side ITCB HV TWIN This equipment will brew either tea or coffee into an awaiting dispenser or reservoir in either the left or right side brewing station The brewer may have an auxiliary hot water faucet that can be mounted on the front left or right side This equipment is only for indoor use on a sturdy counter or shelf The Infusion Series combines BrewWISE CDBC and Tea Brewers into one ITCB is able to brew both tea and coffee with recipe settings It has an LCD for digital readout and programming along with the Smart Funnel options for coffee The user is able to select regular or quick brew for tea programming Other features include Pre Infusion Pulse Brew quick and standard brew and BrewWISE Energy Savings mode BUNNLink compat ible Smart Reader compatible Freshness Timer Sanitation Alert and sweetener with low product detection CONTENTS
19. lter Approximately three to five ounces is recommended for three gallons of beverage Level the bed of tea leaves by gently shaking Slide the funnel into the funnel rails until it stops On dual dilution models rotate the funnel handle left or right to align the funnel discharge over the reservoir The ON OFF must be ON Select which batch size to brew Momentarily press and release the assigned BREW switch There may be certain situations in which the brew cycle will not begin when BREW is pressed a SWITCH NOT ON ON OFF must be ON b BREW TEMPERATURE LOW wait until heated or cancel BREW LOCKOUT option CHECK FUNNEL remove funnel empty previously brewed leaves and replace with fresh tea leaves d DISABLED select different brew switch or batch size If none of the above messages are displayed the display will read NOW BREWING and show the time re maining in the brew cycle Following the brew will be a countdown of drip time DRIPPING which shows the time remaining until the tea no longer drips from the funnel tip 10 Carefully remove the brew funnel and discard the tea leaves and filter only after visible dripping stops COFFEE BREWING ITCB HV ONLY WITHOUT A SMART FUNNEL AND G9 2T DBC GRINDER 8 9 Begin each brew cycle with a clean empty brew funnel Insert a BUNN filter into the funnel Pour the fresh coffee into the filter and level the bed of grounds by gently shaking Slide the f
20. ng range for sweetener is 25 60psi 35psi recommended 7 36748 3 062111 OPERATING CONTROLS ITCB DV amp HV F Brewer Control A ENABLE BREW ON OFF SWITCH Pressing the ENABLE BREW ON OFF switch pad will alternately turn the brewer on and off Pressing this pad during the brew cycle will interrupt the brew cycle stopping the flow of water Pressing this pad during programming of the brewer will exit the setup and return to the main screen B PROGRAMMING left This hidden pad can be used to scroll backwards through the function list while in programming mode C BREW A B C and FUNCTION When the ENABLE BREW is ON and the brewer is on the main screen not in programming mode momen tarily pressing and releasing this pad will begin a brew cycle These are also used to program the brewer when in the programming mode D PROGRAMMING right Pressing and holding this pad allows entry into the programming menus Pressing and releasing the pad steps through each function screen while in the programming mode E BATCH SELECTOR PADS Pressing the pad corresponding to the Half or Full batch selects the amount of product to be brewed Pressing a different pad after a brew cycle has been initiated does not change the brew batch in progress Light indicates the selected batch to brew Also used in programming to adjust settings on both batch sizes F FUNCTION SCREEN This is the display which shows the various functio
21. ns of the brewer and allows the programming to be ac complished G FUNNEL SENSING COIL ITCB ONLY This is used to receive information from the Smart Funnel handle recipe cards and ad cards H FUNCTION SCREEN SWITCHES Digital This is used to select options NO that appear on the display during programming Brewer This is used to select options DONE that appear on the display during programming Control This is used to select options YES that appear on the display during programming 8 36748 3 111010 INITIAL SET UP Insert an empty funnel into the funnel rails Place an empty server under the funnel Connect the brewer to the power source Make sure the ON OFF switch is ON LED will be lit Water will flow into the tank and stop when the tank is filled to its capacity Display will show PLEASE WAIT TANK FILLING until tank is filled with water Wait approximately twenty minutes for the water in the tank to heat to the proper temperature Display will show READY TO BREW WATER TEMP 205 when tank is at operating temperature Some water will drip from the funnel during this time this is due to expansion and should not occur thereafter MODELS w FAUCET Place a small container beneath the faucet and open the faucet handle Release it when you hear the tank refilling Water volumes and flow settings have been preset at the factory Refer to the Programming Manual should the volume need to be increased or dec
22. odifications to this warranty or to make additional warranties that are binding on BUNN Accordingly statements by such individuals whether oral or written do not constitute warranties and should not be relied upon If BUNN determines in its sole discretion that the equipment does not conform to the warranty BUNN at its exclusive op tion while the equipment is under warranty shall either 1 provide at no charge replacement parts and or labor during the applicable parts and labor warranty periods specified above to repair the defective components provided that this repair is done by a BUNN Authorized Service Representative or 2 shall replace the equipment or refund the purchase price for the equipment THE BUYER S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT WHETHER DERIVED FROM WARRANTY OR OTHERWISE SHALL BE LIMITED AT BUNN S SOLE OPTION AS SPECIFIED HEREIN TO REPAIR REPLACEMENT OR REFUND In no event shall BUNN be liable for any other damage or loss including but not limited to lost profits lost sales loss of use of equipment claims of Buyer s customers cost of capital cost of down time cost of substitute equipment facilities or services or any other special incidental or consequential damages 392 A Partner You Can Count On Air Infusion AutoPOD AXIOM BrewLOGIC BrewMETER Brew Better Not Bitter Brew WISE BrewWIZARD BUNN Espress BUNN Family Gourmet BUNN Gourmet BUNN
23. periods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period This warranty does not apply to any equipment component or part that was not manufactured by BUNN or that in BUNN s judgment has been affected by misuse neglect alteration improper installation or operation improper maintenance or repair non periodic cleaning and descaling equipment failures related to poor water quality damage or casualty In addition the warranty does not apply to replacement of items subject to normal use including but not limited to user replaceable parts such as seals and gaskets This warranty is conditioned on the Buyer 1 giving BUNN prompt notice of any claim to be made under this warranty by telephone at 217 529 6601 or by writing to Post Office Box 3227 Springfield Illinois 62708 3227 2 if requested by BUNN shipping the defective equipment prepaid to an authorized BUNN service location and 3 receiving prior authorization from BUNN that the defective equipment is under warranty THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY WRITTEN OR ORAL EX PRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE The agents dealers or employees of BUNN are not authorized to make m
24. reased The brewer is now ready for use in accordance with the instructions for Tea Brewing and Coffee Brewing Brew water temperature is factory set at 205 F 96 1 C Areas of high altitude will require lowering this tempera ture to prevent boiling This chart should be used as a guide when readjusting the brew water temperature Altitude Boiling point of water Feet Recommended water temperature C VIEWING ASSIGNED RECIPES Make sure the ON OFF switch is OFF LED will not be lit Press and hold BREW A The display will show the name of the recipe assigned to Brew A along with SWITCH NOT ON This is to indicate that a brew cannot be initiated while the ON OFF switch is OFF Repeat for BREW B and BREW C Twins only Repeat steps 1 3 for other side Make sure the ENABLE BREW ON OFF switch is OFF To view the asset number of the machine press and hold the left hidden button until the display reads ANXXXXXX ASSET NUMBER Release the left hidden button After a 5 second delay the display will read This is the serial number of the machine 36748 3 111010 8 9 TEA BREWING Begin each brew cycle with a clean empty brew funnel and server Be sure the server lid doesn t interfere with the flow of dilution water Insert a BUNN filter into the funnel Pour the packet of loose fresh tea leaves into the fi
25. te from water supply line NOTE Bunn O Matic recommends 3 8 copper tubing for all installations from the 1 2 water supply line A tight coil of tubing in the water line will facilitate moving the brewer to clean the counter top Bunn O Matic does not recommend the use of a saddle valve to install the brewer The size and shape of the hole made in the supply line by this type of device may restrict water flow As directed the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration FDA this equipment must be installed with adequate backflow pre vention to comply with federal state and local codes For models installed outside the U S A you must comply with the applicable Plumbing Sanitation Code for your area Plumbing Hook Up 1 Remove the shipping cap from the fitting on the rear of the brewer 2 STANDARD MODELS Securely attach adaptor elbow assembly to the 75 11 5 NH HOSE THREAD fit ting at the rear of the brewer TWIN MODELS Securely attach the tube assembly supplied in parts box to water supply line Securely attach the elbow assemblie to the 75 11 5 NH HOSE THREAD fittings at the rear of the brewer Connect the tube assembly to the elbows 3 Flush the water line and Securely attach it to the adaptor elbow 4 on the water supply OPTIONAL SWEETENER Connect sweetener line to fitting on back of brewer labeled SWEETENER NOTE Operati
26. that has a minimum capacity of 2 0 gallons 7 5 L ITB ITCB 3 5Gal 13 25L for HV single or 6 0Gal 22 7L for HV Twin 5 Release the white clamp to drain water from the tank 6 When tank is empty replace the hose onto solenoid or flow control and tighten the black clamp NOTE Do not tighten white clamp 7 Replace the access cover 8 On HV units use care so you do not pinch the dilution hoses when replacing cover 11 36748 3 092712 SANITIZING OPTIONAL SWEETENER All Models Remove all the quick disconnects QCD from all the containers Fill a suitable pail or bucket with a warm soapy tap water solution 140 3 Submerge all disconnects gas and liquid in the soapy solution and then clean them using a nylon bristle brush Do not use a wire brush Rinse with clean water Using a plastic pail prepare approximately five 5 gallons of Kay 5 or equivalent sanitizing solution with at least 100 ppm of available chlorine in 120 F water Rinse the 1 disconnects QCD s in the sanitizing solution Special sanitizing fittings must be attached to each 1 disconnect QCD s If these fittings are not available the fittings from empty 1 bags can be cut from the bags and used These fittings open the disconnect so the sanitizing solution can be drawn through the disconnect opening T Place all the B I B disconnects QCD s into the pail of sanitizing solution N
27. unnel into the funnel rails until it stops Place an empty server under the funnel The ON OFF must be ON Select the FULL batch size Momentarily press and release the assigned BREW switch There may be certain situations in which the brew cycle will not begin when BREW is pressed a SWITCH NOT ON ON OFF must be ON b BREW TEMPERATURE TOO LOW wait until heated or cancel BREW LOCKOUT option c CHECK FUNNEL remove funnel empty previously brewed grounds and replace with fresh d DISABLED select different brew switch or batch size COFFEE FUNNEL appears when brew volume is greater than 86 0 oz 2 54 and pulse brew is disabled Check to make sure the correct funnel is in place and then press BREW again If none of the above messages are displayed the display will read NOW BREWING and show the time remain ing in the brew cycle Following the brew will be a countdown of drip time DRIPPING which shows the time remaining until the coffee no longer drips from the funnel tip 10 Carefully remove the brew funnel and discard the grounds and filter only after visible dripping stops WITH A SMART FUNNEL AND G9 2T DBC or MHG GRINDER ITCB HV ONLY 1 2 di Select the small batch size on the grinder Insert a BUNN filter into the funnel Grind the selected amount of fresh coffee into the Smart Funnel using the G9 2T DBC or MHG with Smart Funnel operation and level the grounds by gently shaking 10 36748 3 111010
Download Pdf Manuals
Related Search