AII 13050 - Automatic Day And Night Mirror.recover.fm
Contents
1. CLIP supplied 4 DRIVER S A PILLAR TRIM QON0533AH 5 of 15 www collegehillshonda com 14 Pull away the door opening seal from around the dashboard 2 RETAINING TABS 3 CLIPS SL N pRIVER S DASHBOARD 2HOOKS SIDE COVER DOOR OPENING SEAL Q083001AH Pull away 15 Remove the driver s dashboard side cover three clips two retaining tabs and two hooks 16 Remove the driver s dashboard lower cover nine clips and unplug the vehicle connectors if equipped VEHICLE CONNECTORS if equipped DRIVER S DASHBOARD LOWER COVER 9 CLIPS QB62424AJ 6 of 15 All 47335 1211 Installing the Automatic Day Night Mirror 17 Install the automatic day night mirror With FCW LDW Camera Replace the spring as needed Slide the automatic day night mirror stay onto the mirror mount then turn the mirror stay counterclockwise as shown VEHICLE SPRING Replace MIRROR MOUNT SPRING Turn the mirror stay counterclockwise NEEDLE NOSE PLIERS MIRROR MOUNT DAY NIGHT MIRROR STAY AUTOMATIC DAY NIGHT MIRROR CAMERA COVER QB70501BK 2012 American Honda Motor Co Inc All Rights Reserved www collegehillshonda com Without FCW LDW Camera Tighten the TORX screw T20 TORX WRENCH Torque 1 6 2 0 N m 0 16 0 20 kgf m 1 2 1 5 Ibf ft H P MOUNT AUTOMATIC DAY NIGHT MIRROR L Q083099CH Routing the Automatic Day Night2. 8 9 All 47335 1211 Remove the driver s sunvisor oN FRONT DRIVER S SUNVISOR QO90603AK Pull away the driver s door opening seal Pull the clip DRIVER S A PILLAR DRIVER S A PILLAR TRIM CLIP _ if equipped DOOR OPENING SEAL Pull away 2 CLIPS Q082301AK Pull out the driver s A pillar trim to release the clips 2012 American Honda Motor Co Inc All Rights Reserved www collegehillshonda com 10 Putashop towel in the opening between the driver s A pillar trim and the dashboard to prevent dropping the A pillar clips Take care not to damage the driver s A pillar trim DRIVER S A PILLAR TRIM DRIVER S A PILLAR SHOP TOWEL Q092001AK 11 Remove the driver s A pillar trim from the upper clip unplug the vehicle connector if equipped Carefully remove the shop towel and any clips that fell from the driver s A pillar trim NOTE The upper clip will stay in the body VEHICLE CONNECTOR UPPER CLIP if equipped DRIVER S A PILLAR TRIM Q082308AK 2012 American Honda Motor Co Inc All Rights Reserved All 47335 1211 12 Remove the remaining upper clip from the drivers A pillar Push two tabs Discard Q082303AK 13 Install the new clip supplied to the driver s A pillar trim NOTE When reinstalling the A pillar trim refer to the Service Manual for the correct overlap procedure
3. DAY NIGHT MIRROR HARNESS a esiosAl 33 Insert the automatic day night mirror harness between the dashboard and the driver s A pillar DASHBOARD AUTOMATIC DAY NIGHT MIRROR DRIVER S A PILLAR Q083109BH 2012 American Honda Motor Co Inc All Rights Reserved All 47335 1211 34 Align the green tape on the automatic day night mirror harness with the vehicle clip and secure the automatic day night mirror harness to the vehicle harness with one wire tie A WIRE TIE A AUTOMATIC DAY NIGHT MIRROR HARNESS VEHICLE HARNESS VEHICLE CLIP Q083110CH If the vehicle is equipped with FCW LDW camera continue with step 35 otherwise go to step 37 35 Remove the camera cover eight retaining tabs CAMERA COVER 8 RETAINING TABS QB62207AK 11 of 15 www collegehillshonda com 36 Route the automatic day night mirror harness under the headliner as shown Be careful not to crease the headliner Go to step 38 VEHICLE HARNESS ka S AUTOMATIC DAY NIGHT MIRROR HARNESS QB62208AK Without FCW LDW Camera 37 Route the automatic day night mirror harness under the headliner as shown Be careful not to crease the headliner HEADLINER S lt S A w AUTOMATIC DAY NIGHT MIRROR HARNESS Q083111CH 38 Plug the automatic day night mirror harness 7 pin connector to the automatic day night mirror AUTOMATIC DAY NIGHT 7 PIN CONNECTOR AUTOMATIC
4. Mirror Harness 18 Using isopropyl alcohol on a shop towel thoroughly clean the fuse case where the fuse label will attach AUTOMATIC DAY NIGHT MIRROR HARNESS 2A FUSE LABEL FUSE CASE Clean with isopropyl alcohol Q091801AH 19 Attach the 2A fuse label to the fuse case on the automatic day night mirror harness 2012 American Honda Motor Co Inc All Rights Reserved 20 Plug the automatic day night mirror harness 6 pin connector into the fuse box 6 pin connector If another accessory harness is already plugged into the fuse box unplug it and plug in the automatic day night mirror harness DRIVER S SIDE FUSE BOX AUTOMATIC DAY NIGHT MIRROR HARNESS 6 PIN w TA g ETA lt 1 m Yel FUSE BOX 6 PIN CONNECTOR Q083102AH 7 of 15 All 47335 1211 www collegehillshonda com With Another Accessory Harness Remove the dummy connector from the automatic day night harness and plug the other accessory harness 6 pin connector into the automatic day night mirror harness 6 pin connector AUTOMATIC DAY NIGHT MIRROR HARNESS 6 PIN FUSE BOX 6 PIN CONNECTOR OTHER ACCESSORY HARNESS 6 PIN CONNECTOR CONNECTOR Discard DRIVER S SIDE FUSE BOX FUSE BOX 6 PIN CONNECTOR QB70502AK 8 of 15 21 Route the automatic day night mirror harness to the driver s dashboard lower cover opening as sh
5. 082401CK Remove the drivers and passenger s sunvisor holders Gr PASSENGER S SUNVISOR HOLDER DRIVER S Rotate SUNVISOR HOLDER Rotate Q082404BK 2012 American Honda Motor Co Inc All Rights Reserved 4 All 47335 1211 Remove the rearview mirror With FCW LDW Camera Remove the rearview mirror from the mirror mount by rotating the stay 90 clockwise MIRROR Rotate 90 MOUNT clockwise MIRROR MOUNT STAY REARVIEW MIRROR Discard 721412AE Without FCW LDW Camera e Remove the cover two retaining tabs e While holding down the hook as shown remove the rearview mirror from the mirror mount COVER Discard MIRROR MOUNT Q083101AH 3 of 15 www collegehillshonda com Wrap the end of a flat tip screwdriver with tape Locate the slot in the bracket cover and insert a flat tip screwdriver into the slot Push the hook with the flat tip screwdriver FLAT TIP SCREWDRIVER BRACKET COVER DRIVER S SUNVISOR FRONT Make sure the hook slides into the bracket cover Push the hook While pushing in on the hook rotate the sunvisor backward qogo602BK about 45 6 While pushing in on the hook rotate the driver s sunvisor backward about 45 Make sure the hook slides into the bracket cover NOTE If the hook did not stay pushed in return the driver s sunvisor to its original position and repeat steps 5 and 6 4 of 15 7
6. DAY NIGHT MIRROR Q083112BH 12 of 15 All 47335 1211 2012 American Honda Motor Co Inc All Rights Reserved 39 2012 American Honda Motor Co Inc All Rights Reserved www collegehillshonda com Align the green tape on the automatic day night mirror harness with the headliner as shown Route the automatic day night mirror harness through the groove in the harness cover Secure the harness cover to the automatic day night mirror stay Slide the harness cover inside the headliner 4 Door AUTOMATIC DAY NIGHT MIRROR HARNESS GREEN TAPE HARNESS COVER AUTOMATIC DAY NIGHT 7X0 MIRROR Ry HARNESS 77 AUTOMATIC DAY NIGHT MIRROR STAY HARNESS COVER AUTOMATIC DAY NIGHT MIRROR eat All 47335 1211 2 Door AUTOMATIC DAY NIGHT MIRROR HARNESS HEADLINER HARNESS COVER DAY NIGHT MIRROR AUTOMATIC DAY NIGHT MIRROR STAY HARNESS COVER AUTOMATIC DAY NIGHT MIRROR Q091902BH 13 of 15 40 41 14 of 15 www collegehillshonda com Using isopropyl alcohol on a shop towel thoroughly clean the vehicle panel where the EPT sealer will attach NOTE Do not crease the headliner for the following procedure VEHICLE PANEL AUTOMATIC DAY NIGHT EPT SEALER HEADLINER SS VEHICLE PANEL Clean with isopropyl alcohol EPT SEALER AUTOMATIC DAY NIGHT MIRROR HARNESS WITH FCW LDW CAMERA Do not s
7. T MIRROR HARNESS AUTOMATIC DAY NIGHT MIRROR 2A FUSE AUTOMATIC DAY NIGHT MIRROR SUBHARNESS a With E CON switch QB62209AK 2 of 15 INSTALLATION Customer Information The information in this installation instruction is intended for use only by skilled technicians who have the proper tools equipment and training to correctly and safely add equipment to your vehicle These procedures should not be attempted by do it yourselfers All 47335 1211 1 Disconnect the negative cable from the battery If the vehicle is equipped with map light continue with step 2 otherwise go to step 3 2 Remove the left and right lenses from the map light console four retaining tabs for each lens Remove the two bolts With Moonroof Remove the map light console Then unplug three vehicle connectors and remove the switch four retaining tabs 3 VEHICLE CONNECTORS 4 RETAINING TABS RIGHT MAP Se LIGHT LENS MAP LIGHT CONSOLE 2 BOLTS 4 RETAINING TABS LEFT MAP 4RETAINING SWITCH LIGHT LENS TABS QA21705AH 2012 American Honda Motor Co Inc All Rights Reserved www collegehillshonda com Without Moonroof and With Hands Free Link Remove the map light console unplug two vehicle connectors 2 VEHICLE CONNECTORS FRONT T 4 RETAINING TABS RIGHT MAP LIGHT LENS MAP LIGHT CONSOLE 2 BOLTS 4 RETAINING LEFT MAP ABS LIGHT LENS Q
8. e wire tie B secure the automatic day night mirror subharness 6 pin connector to the vehicle harness as shown Wire tie A VEHICLE secured in HARNESS Step 26 AUTOMATIC DAY NIGHT MIRROR SUBHARNESS 6 PIN CONNECTOR QB62205BK 9 of 15 www collegehillshonda com 28 Using one wire tie B secure the automatic day night mirror harness 5 pin connector to the automatic day night mirror subharness as shown Go to step 32 AUTOMATIC DAY NIGHT MIRROR SUBHARNESS AUTOMATIC DAY NIGHT MIRROR HARNESS 5 PIN CONNECTOR WIRE TIE B QB62206AK Without E CON Switch 29 Unplug the vehicle 5 pin connector from the VSA switch and plug it into the automatic day night mirror harness 5 pin connector VSA SWITCH VEHICLE 5 PIN CONNECTOR AUTOMATIC DAY NIGHT Q083107AH 10 of 15 All 47335 1211 30 Plug the automatic day night mirror harness 5 pin connector to the VSA switch VSA SWITCH AUTOMATIC DAY NIGHT MIRROR HARNESS 5 PIN CONNECTOR Q091901BH 31 Using one wire tie A secure the automatic day night mirror harness to the vehicle harness as shown VEHICLE AUTOMATIC DAY NIGHT MIRROR HARNESS WIRE TIEA VEHICLE HARNESS AUTOMATIC DAY NIGHT MIRROR HARNESS QB91101AK 2012 American Honda Motor Co Inc All Rights Reserved www collegehillshonda com 32 Route the automatic day night mirror harness toward the outside of the vehicle as shown AUTOMATIC
9. ecure the vehicle harness VEHICLE PANEL Clean with isopropyl alcohol ay di e EPT SEALER ee MIRROR HARNESS Secure the automatic day night mirror harness to the vehicle panel with one EPT sealer as shown Be careful not to crease the headliner 42 Using three wire ties A secure the automatic day night mirror harness to the vehicle harness as shown 3 WIRE TIES A VEHICLE HARNESS AUTOMATIC DAY NIGHT MIRROR HARNESS Q083115BH 43 Check that all wire harnesses are routed properly and all connectors are plugged in 44 Check the overlap between the headliner and the driver s A pillar trim Refer to the service manual If necessary adjust the overlap 45 Reinstall all removed parts 46 Reconnect the negative cable to the battery 47 Press and hold the radio power button for two seconds to restore the radio and navi if equipped system functions 48 Reset the clock 49 If the IMA battery level gauge is at zero start the engine and hold the rpm between 3500 and 4000 no load in P or N position until the Charge Assist meter indicates the IMA system has stopped charging the battery NOTE e Check the operation of the automatic day night mirror according to the Operating Instructions supplied e Adjust the zone and calibrate as required 50 Put the Operating Instructions in the glove box All 47335 1211 2012 American Honda Motor Co Inc All Rights Reserved www college
10. hillshonda com FUNCTION CHECK 1 Turn the ignition switch to ON II but do not start the engine AUTOMATIC DAY NIGHT MIRROR SWITCH Turn on AUTOMATIC DAY NIGHT MIRROR TNE 2 Turn the switch on Check that the LED lights 2012 American Honda Motor Co Inc All Rights Reserved 3 All 47335 1211 Cover the front sensor on the automatic day night mirror with your hand and use a flashlight to light the rear sensor on the automatic day night mirror Check to make sure the mirror surface becomes dim AUTOMATIC DAY NIGHT MIRROR SURFACE FRONT SENSOR FLASHLIGHT Cover REAR SENSOR 030407AB Step on the brake pedal and move the select lever to the R position Repeat step 3 and check to make sure the mirror surface does not become dim e Make sure that the parking brake is locked securely e If the automatic day night mirror does not function properly check the fuse and all connectors 15 of 15
11. own WIRE TIE A AUTOMATICDAY NIGHT VEHICLE MIRROR HARNESS HARNESS Q083104AH 22 Using one wire tie A secure the automatic day night mirror harness to the vehicle harness If the vehicle is equipped with E CON switch continue with step 23 otherwise go to step 29 23 Plug the automatic day night mirror subharness 5 pin connector into the automatic day night mirror harness 5 pin connector AUTOMATIC DAY NIGHT MIRROR SUBHARNESS 5 PIN CONNECTOR AUTOMATIC DAY NIGHT MIRROR HARNESS 5 PIN CONNECTOR QB62201AK All 47335 1211 2012 American Honda Motor Co Inc All Rights Reserved www collegehillshonda com 24 Unplug the vehicle 6 pin connector from the E CON switch and plug it into the automatic day night mirror subharness 6 pin connector E CON SWITCH VEHICLE 6 PIN CONNECTOR AUTOMATIC DAY NIGHT MIRROR SUBHARNESS 6 PIN CONNECTOR QB62202AK 25 Plug the automatic day night mirror subharness 6 pin connector to the E CON switch E CON SWITCH AUTOMATIC DAY NIGHT MIRROR SUBHARNESS 6 PIN CONNECTOR QB62203AK 2012 American Honda Motor Co Inc All Rights Reserved All 47335 1211 26 Using one wire tie A secure the automatic day night mirror harness to the vehicle harness as shown VEHICLE HARNESS AUTOMATIC DAY NIGHT MIRROR HARNESS WIRE TIEA VEHICLE HARNESS AUTOMATIC DAY NIGHT MIRROR HARNESS QB62204AK 27 Using on
12. www collegehillshonda com HONDA Accessory Application Publications No All 13050 INSTALLATION AUTOMATIC DAY NIGHT 2013 CIVIC issue Dain INSTRUCTIONS MIRROR 2 AND 4 DOOR novae NOV 2012 PARTS LIST Subharness Kit With E CON Switch Attachment Kit P N 08V03 TRO 1A0 P N 08V03 TRO 100 Automatic day night mirror subharness Automatic day night mirror harness gt AS 2 Wire ties B O Harness cover g Automatic Day Night Mirror Kit With FCW LDW CAMERA P N 08V03 TA0 100A Automatic day night mirror Se JZ X gt 6 Wire ties A SS Spring sip Operating Instructions Automatic Day Night Mirror Kit Without FCW LDW EPT sealer CAMERA P N 08V03 TRO 100A Automatic day night mirror Fuse label Operating Instructions 2012 American Honda Motor Co Inc All Rights Reserved All 47335 1211 08V03 TRO 1010 90 1 of 15 www collegehillshonda com TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat tip screwdriver Ratchet 10 mm Socket Isopropyl alcohol Needle nose pliers Shop towel Diagonal cutters T20 TORX wrench Flashlight Tape The following tool is available through the Honda Tool and Equipment Program On the iN click on Service gt Service Bay gt Tool and Equipment Program then enter the number under Search Or call 888 424 6857 e Plastic Trim Tool T N SILTRIMTL10 Illustration of the Automatic Day Night Mirror on the Vehicle AUTOMATIC DAY NIGH
Download Pdf Manuals
Related Search