Service Manual
Contents
1. Letter Description Configuration Code C Commercial Cord H Harmonized Cord R Rockbestos Cord H C CEE 7 7 16 Amp 250 VAC Assembly Only D 330P6W 30 Amp 250 VAC Pin amp Sleeve H I IEC 309 16 Amp 250 VAC Pin amp Sleeve Assembly Only R L6 30P 30 Amp 250 VAC Right Angle Twist Lock S L6 30P 30 Amp 250 VAC Straight Twist Lock U L6 20P 20 Amp 250 VAC Straight Twist Lock Used in Model Designation at the label located on the left end panel If the background color is YELLOW the toasting time is 17 seconds Indicates that the plug comes supplied with a Harmonized Cord If the background color is GRAY the toasting time is 10 sec onds If your toaster has been changed to 17 seconds fol low all instructions information pertaining to Mfg 9210618 to 9210622 Model Specifications Model Number Wg Number Voltage Wattage Amperage Hz Toasting Time vcrasonp 9210600 208 200 240 3326 3700 4500 139 1688 183 60 17secs vcrasong 9210602 208 290 240 3326 3700 4000 139 168 183 60 irsee vcrasons 9210604 208 290 240 3926 3700 4000 139 1683 60 17secs vcrasons 9210612 208 200 240 33 3700 4000 139 168 183 60 Approx 10 secs vcrasomp 92106182. 175 Volts Toaster shuts down TEMP DOWN SCALE PO Fault Message P N 1010776 Rev 03 06 McDonald s roundup RAPID TOASTER VCT 250 MAINTENANCE AWARNING A Turn the unit off disconnect the power source and allow the unit to cool down before performing any ser vice or maintenance on the unit Daily Cleaning NOTE Also refer to TS 019 Card P N 1010732 1 Turn the Rocker Switch power ON OFF to OFF unplug the toaster and allow it to cool down Put on Heat Resistant Gloves and remove the Bun Feeder and Bun Chute Figure 11 Wash them at the sink and allow to air dry Remove the Release Sheet Figure 9 and lay it on a clean flat dry surface Spray McD All Purpose Super Concentrate HCS on a clean dry towel Wipe the towel firmly across the Release Sheet lengthwise over its entire surface Immediately repeat this procedure with a clean dry towel dampened with KAYQUAT Sanitizer HCS solution and allow the Release Sheet to air dry Turn the Release Sheet over and repeat this cleaning procedure on its other side Open the Front Heel Club side Conveyor Cover spray McDO All Purpose Super Concentrate HCS on a clean dry towel and wipe the surface of the Groovy Belt Wrap firmly from side to side and then top to bottom Immediately repeat the procedure with a clean dry towel dampened with KAYQUAT Sanitizer HCS solution Close the Conveyo
3. Parts Identification Axial Fan Ol NM ON 4 gt Z6 e e iS 9 ey e e Auxiliary Heater h Interlock Switch I 9 e Drive Chain EN Q 9 Idler Sprocket Transformer 5 16 Bore qo Drive Sprocket 1 2 Bore o Drive Sprocket 1 2 Bore 7 6 Auxiliary Relay Ove Platen Relay Temperature Control E Position of 3 RPM Motor Position of 9 RPM Motor Drive Motor Assy for 17 Second for 10 Second Toaster _ Toaster Rocker Switch Power On Off 5 5 od o Hi Limit Control a Saab Fan Blade Hardware List The following items are only available in packages of 10 Item Part Description Qty Item Part Description Qty No No A 100P864 Label Caution Hot 1 S 212P111 Spacer 1 B 308P115 Screw 8 32 x 3 8 10 mm 10 T 308P157 Screw 8 32 x 1 4 1 C 310P154 Screw 10 32 x 3 8 4 U 308 120 Screw 8 32 x 5 8 1 D 304P105 Nut 44 40 KEPS 1 V 308P104 Screw 8 32 x 3 8 1 E 406P107 Cable Tie 1 W 308P105 Screw 48 32 x 1 2 1 F 308P143 Nut 48 32 KEPS 3 X 331P103 Shoulder Bolt 5 16 18 x I 1 G 310P103 Screw 10 32 x 1 4 1 Y 040 111 Bushing Shorty 1 2 1 310P140 Washer 10 3 not shown 308P101 Nut 8 32 3 Z 306P105 Screw 26 32 x 1 2 1 J 306P101 Nut Hex 6 32 1 BB 331P106 Lockwasher 5 16 1 K
4. 2n RAPID TOASTER A J Antunes amp Co MODEL VCT 250 McDonald s Manufacturing Numbers 9210600 602 604 609 61 2 618 619 620 622 Place this manual in the Toaster section of your Equipment Manual Manufactured exclusively for McDONALD S BY A J ANTUNES amp CO 180 KEHOE BLVD CAROL STREAM ILLINOIS 60188 U S A PHONE 1 630 784 1000 TOLL FREE 1 877 392 7854 FAX 1 630 784 1650 www ajantunes com TABLE OF CONTENTS Owner Information 22222 2 2 7 e eere etn EU 2 Operating Instructions Warranty Information 2 Toaster Service Technical Assistance 2 Safety Features 2222 Specifications c cccessccessccecessseesssceesssrenssseenssnes 3 Maintenance eene Model 3 Daily Cleaning Toasting Time 3 Monthly Bun Temperature Test Model 3 inae Electrical Cord amp Plug Configurations 3 Measure Conveyor Belt Chains for Stretch 0 2
5. 2 1 0006 1110 4 Replacing Groovy Belt Wraps Weights 4 Install New Release Sheet monthly Important Safety Information 5 Checking Bun Landing Area Temperature 6 Adjusting Measuring and or Replacing Roller Unpacking vise sinc sete 6 Tensioner 15 Assembling the 6 Troubleshooting cesses 16 6 Replacement Parts eene 20 Optional 26 Wiring Diagrams enne m 27 LIMITED WARRANTY The Antunes Food Service Equipment Division of A J Antunes amp Co provides the following limited warranty to the original purchaser of all McDonald s Equipment manufactured and purchased after January 1 2003 All components are warranted against defects in the material and workmanship for a period of two 2 years from date of original installation not to exceed 30 months from date of shipment from our factory If any part becomes defective during the first two 2 years after the original installation date Antunes Food Service will pay negotiated straight time labor costs to an Authorized Service Agent to replace the part plus travel expenses up to 50 mi
6. 208 290 240 3926 3700 4900 13 9 168 183 60 Approx 17 secs vcrasocu 2069 208 290 240 3926 3700 4900 13 9 168 183 60 Approx 17 secs vcrasonm 9210620 208 290 240 3926 37004390 13 9 168 183 60 Approx 17 secs vcrasons 9210622 208 290 240 3926 3700 4900 13 9 168 183 60 Approx 17 secs United States and Canada only P N 1010776 Rev 03 06 3 McDonald s T Foodservice Equipment RAPID TOASTER VCT 250 roundup SPECIFICATIONS continued Dimensions 14 __ 21 1 2 11 3 8 6 mm 546 mm 289 mm mH i F 22 1 8 546 mm 23 1 2 597 mm 15 3 8 891 mm Weights Lbs Kgs Net 95 43 1 Shipping 105 47 6 n 4 P N 1010776 Rev 03 06 McDonald s Antunes Foodservice Equipment roundup RAPID TOASTER VCT 250 IMPORTANT SAFETY INFORMATION Throughout this manual you will find the following safety words and symbols that signify important safety issues with regards to operating or maintaining the equipment WARNING A GENERAL WARNING Indicates informa tion important to the proper operation of the equipment Failure to observe may result in damage to the equipment and or severe bodily injury or death WARNING A ELECTRICAL WARNING Indicates infor mation relating to possible shock hazard Failure to observe may
7. 306P123 Screw 6 32 x 7 8 1 CC 212P118 Flat Washer 5 16 1 L 308P145 Nut Hex Acorn 8 32 1 DD 331P101 Nut Hex 5 16 x 18 1 M 100P900 Label Service 1 EE 300P102 Nut Tinnerman 2 325 104 Washer 1 4 1 FF 306 104 Screw 6 32 x 1 4 8 325 109 Screw 1 4 20 1 2 1 GG 325P163 Setscrew 1 4 28 x 5 16 8 P 308P124 Screw 1 Way 8 32 x 1 2 1 HH 308P183 Screw Hexhead 8 32 x 3 8 1 R 10P1022 Label Heaters 1 308P144 Screw 8 32 x 1 4 6 Head 1 P N 1010776 Rev 03 06 25 2n Antunes Foodservice Equipment RAPID TOASTER VCT 250 roundup OPTIONAL ACCESSORIES There is also a kit for the Bun Buffer Landing Zone available for purchase It consists of the following parts Bun Buffer Landing Zone Accessory The optional Bun Buffer Landing Zone consists of the following parts 1 Bun Buffer Landing Zone Kit P N 7000378 a BBLZ Main Assembly P N 0011741 Front Panel Assembly P N 0021328 1 BBLZ Main Assembly P N 0011741 b 2 Front Panel Assembly P N 0021328 c Bun Chute P N 0503425 d 3 Thumb Screw P N 3080191 Instruction Sheet P N 1010842 Figure 20 Optional Bun Buffer Landing Zone Kit McDonald s Antunes Foodservice Equipment api TOASTER VCT 250 WIRING DIAGRAMS Pictorial Wiring Diagram POWER CORD a 14 GA AWM 105 C gt 14 TFE 200 C ec 16 AWM 105 C NN 5 16 TFE 200 C CONTROL i AWM 10
8. Pull the hinge pin out of the Groovy Belt Wrap and then remove and discard this Groovy Belt Wrap Repeat this process on the Rear Crown side 7 Foodservice Equipment 12 Bun Feeder Rear Crown Conveyor Cover Safety Interlock Ss Switch 1 each side Bun Chute Front Heel Conveyor Cover Figure 11 Replacing Groovy Belt Clean the Conveyor Belt Chains 1 Spray McD All Purpose Super Concentrate HCS on a clean dry towel and wipe the sur face of the Rear Crown Conveyor Belt Chain links firmly from side to side and top to bottom Immediately repeat this procedure with a clean dry towel dampened with KAYQUAT Sanitizer HCS solution and repeat this procedure on the Front Heel Club Conveyor Belt chain 2 Close the Conveyor Cover s plug in the power cord turn on the unit count to seventeen 17 seconds for Mfg 9210600 to 9210604 and 9210618 to 9210622 or ten 10 seconds for Mfg 9210609 to 9210612 Next turn the unit OFF and unplug the power cord NOTE Refer to Figures 2A and 2B in the Operation section of this Manual 3 Open the Conveyor Cover s and repeat Step 1 to clean the other half of both the Front Heel Club and Rear Crown Conveyor Belt Chains P N 1010776 Rev 03 06 McDonald s roundup RAPID TOASTER VCT 250 MAINTENANCE continued Measure Conveyor Belt Chains for Stretch After a period of time the Conveyor Belt Chain links will wear and the
9. Switches not activated by 9 Conveyor covers Buns are not toasting Compression Knobs set incor Set the Bun Thickness Compression Controls to D amp properly rectly 5 for Mfg 9210618 to 9210622 For Mfg 9210600 to 9210612 set the controls to amp 3 See Figures 2A and 2B Toaster temperature not set prop Verify the toaster is set at SP P 560 F 293 C for erly the Platen and SP A 400 F 204 C for the Auxiliary Follow the instructions in the Operation section of this manual Release Sheet is dirty or worn Follow the cleaning and replacement procedure on Groovy Belt Wrap is dirty or worn the current MRC Card TS 019 Bun temperature below 150 F Perform the bun temperature test as described on the 65 6 C current MRC Card TS 019 Replace worn Teflon dampers and or missing springs Contact your Authorized Service Agency for parts and service if necessary Buns cut improperly Contact your bun supplier Crown and or heel Bun Feeder improperly installed Remove and reposition Bun Feeder must be forced into Groovy Belt Wrap not tacky or is Clean or replace Groovy Belt Wrap toaster worn Crown and or heel improperly Buns must be inserted with cut faces facing inward inserted into toaster toward each other heel in front slot and crown in rear slot Groovy Belt Wrap slipping over Clean conveyor belt chain according to the instruc Conveyor Belt Chains tions in the Maintenance sec
10. 392 7854 North America only or 630 784 1000 Assembling the Unit 1 Install the Bun Chute Figure 1 2 Install the Bun Feeder The Bun Feeder clips fit over the tip of the Platen and retain the Release Sheet Figures 1 amp 9 NOTE Check the Release Sheet to make sure it is not caught in the conveyor Additional Release Sheets can be obtained through your Authorized Service Agency Location When placing the toaster into service pay attention to the following guidelines Make sure power to the unit is off and the toaster is at room temperature Do not block or cover any openings on the unit Do not immerse cord or plug in water Keep cord away from heated surfaces Do not allow cord to hang over edge of table or counter Connect the unit to the power supply Refer to the specification plate for the proper voltage CAUTION A All electrical connections must be in accordance with local electrical codes and any other applicable codes CAUTION A Bread may burn Therefore toasters must not be used near or below curtains or other combustible walls and materials Failure to maintain safe operat ing distances may cause discoloration or combustion Bun Chute M Hook Bun Chute over rear Conveyor Cover Rod Bun Feeder Bun Chute WARNING Figure 1 Installing Bun Chute T Foodservice Equipment ELECTR
11. USE will alter nately flash if auxiliary heaters temperature exceeds 420 F 215 C or if auxiliary ther mocouple is disconnected or open Heating circuit will NOT turn off TEMP TEMP DOWN SCALE Figure 6 HI Fault Message T Foodservice Equipment RAPID TOASTER VCT 250 FAULT MESSAGES continued e The temperature controller has an ambient temperature sensor that will shut off all heating circuits if the control compartment ambient temperature becomes excessive 140 F 60 C to 180 F 82 C When this occurs the temperature display will flash Figure 7 To restart the unit ambient must drop to 140 F 60 C and the unit must be turned off then back on If this condition repeats contact your Authorized Service Agency If incoming power drops below 175 Volts the toast er will shut down and the display will read PO Figure 8 To reset the voltage must be over 190 Volts then the unit must be turned off and back on If this condition repeats contact your Authorized Service Agency T Foodservice Equipment roundup CHEC will flash when control compartment ambient temperature is exces sive 140 F 60 C to 180 F 82 C All heaters will shut off TEMP TEMP TEMP SCALE UP DOWN Figure 7 CHEC Fault Message will flash when incoming power drops below Figure 8 10
12. and repeat the measurement P N 1010776 Rev 03 06 McDonald s 7 Figure 12 Measuring Conveyor Chain Rotation Upper Yellow Support Rod Large Link P N 0800121 Small Link P N 0800204 Figure 13 Removing Conveyor Chain Link CAUTION Loose or over tightened conveyor chains can damage the toaster NOTE If you CANNOT stand the coin between the belt and frame you have taken out the wrong sized link or have taken out too many links and damage may occur to the toaster 10 Repeat steps 3 through 7 for the crown rear side of the toaster using a U S Dime coin 11 16 1 8 cm 13 T Foodservice Equipment RAPID TOASTER VCT 250 roundup Replacing Groovy Belt Wraps Upper Yellow Support Rod NOTE Follow Steps 1 3 page 12 if necessary 1 Locate the Hinge Flap on the Groovy Belt Wrap if the Hinge Flap is not visible plug in the power cord and turn the unit on press down on both Conveyor Safety Interlock Switches Figure 11 and wait until the flap is exposed and centered Turn the unit off and unplug the power cord lift flap remove the Hinge Pin and carefully remove the Groovy Belt Wrap from the unit Figure 14 Discard this belt Repeat this process for the rear Crown side PA 2 Instal
13. operating temperature is reached When the toaster approaches the preset tempera ture USE will appear in the Temperature Display and the unit is ready to toast buns The toaster is tested and shipped with the heaters set at a preset recommended temperature If USE does not appear in the window after warm up period see Temperature Adjustments below for recommended tem perature settings and to adjust temperature settings 3 Drop buns into toaster Figure 3 Cut sides of heel and crown must face each other heel club in front crown in back 4 Toasted product will drop into the bun landing area Figure 3 5 Test at least 4 buns before putting toaster into service 6 Turn the Rocker Switch Power On Off to OFF when finished toasting P N 1010776 Rev 03 06 McDonald s HEEL CLUB F A B E 1 9 16 14 3 THICKNESS THICKNESS 09 5 2 5 8 15 9mm 7 16 11 1mm 3 11 16 17 4mm f A C 1 2 12 7mm 4 3 4 19 1mm D 9 16 14 3mm 5 13 16 20 6mm E 5 8 15 9mm 8 7 8 22 2mm 11 6 174 j Figure 2A Bun Thickness Adjustment Controls for Manufacturing Numbers 9210600 to 910604 and 9210618 to 9210622 NOTE Background color of this label is YELLOW co HEEL CLUB A F 1 9 16 14 3mm THICKNESS THICKNESS 3 8 09 5mm 5 8 15 9mm B 2 5 8 15 91 7 16
14. result in damage to the equipment and or severe bodily injury or death A CAUTION Ped WARNING 4 GENERAL CAUTION Indicates informa tion important to the proper operation of the equipment Failure to observe may result in damage to the equipment HOT SURFACE WARNING Indicates infor mation important to the handling of equip ment and parts Failure to observe caution could result in personal injury In addition to the warnings and cautions in this manual use the following guidelines for safe operation of the unit Read all instructions before using equipment For your safety the equipment is furnished with a properly grounded cord connector Do not attempt to defeat the grounded connector Install or locate the equipment only for its intend ed use as described in this manual Do not use corrosive chemicals in this equipment Do not operate this equipment if it has a dam aged cord or plug if it is not working properly or if it has been damaged or dropped This equipment should be serviced by qualified personnel only Contact the nearest Authorized Service Agency for adjustment or repair Do not block or cover any openings on the unit Do not immerse cord or plug in water Keep cord away from heated surfaces Do not allow cord to hang over edge of table or counter P N 1010776 Rev 03 06 McDonald s 5 The following warnings and cautions appear throughou
15. 03359 Bracket Relay 1 81 0503455 Tension Spring Inner 4 67 0503150 Heater Clip 2 82 2100259 Slide Bar 4 68 0021177 Heat Shield Front 1 83 0502199 Spacer 4 69 0021178 Heat Shield Rear 1 84 0500464 Retainer Bearing 1 70 303P127 Hinge Pin Belt Wrap Pk of 10 1 85 0900228 Bun Gauge 1 71 1001023 Label Caution Hot 87 7000203 Thermocouple Retainer Chain Guard Kit 1 Mfg 9210609 amp 612 1 88 0503495 Retainer Tensioner Bracket RH 2 72 0503368 Fascia Bun Stop 89 0503507 Retainer Tensioner Bracket LH 2 Mfg 9210609 amp 612 1 90 060P132 Damper Support Spring Pack of 10 1 73 0900225 Bun Stop Mfg 9210609 amp 612 1 91 0021311 Hinge Bracket Weldment 4 74 7000226 Inner Conveyor Cover 2 92 0503860 Hinge Bracket 1 w hinge bracket for Mfg 9210612 Japan Only 75 7000248 Teflon Damper Kit 93 2110168 Hinge Bun Stop Mfg 9210600 602 1 Includes 4 90 amp 2 Dampers 1 604 618 619 620 and 622 76 0503367 Clamp Damper 2 Note 7000167 Single Bushing amp Retainer Kit 6 77 0503321 Bracket Auxiliary Thermocouple 1 7000224 6 Bushing amp Retainer Kits 1 78 4000170 Fan Blade 1 See Toasting Time Change in the Specifications T Foodservice Equipment 24 section P N 1010776 Rev 03 06 McDonald s roundup RAPID TOASTER VCT 250 REPLACEMENT PARTS continued
16. 11 1mm 3 11 16 17 4mm C 1 2 12 7mm 4 3 4 19 1mm D 9 16 14 3mm 5 13 16 20 6mm E 5 8 15 9mm S7 718 22 2mm F 11 16 17 4mm D Figure 2B Bun Thickness Adjustment Controls for Manufacturing Numbers 9210609 9210612 NOTE Background color of this label is GRAY Heel Club Bun Thickness Adjustment Controls See Figures 2A amp 2B due Rocker Switch Bun Landing Power ON OFF Area Switch Temperature Controls amp Temperature Display Figure 3 Rapid Toaster T Foodservice Equipment RAPID TOASTER VCT 250 Toaster Operation The Rapid Toaster uses a Platen Heater and two Auxiliary Heaters The Platen Heater consists of a heating coil built into the platen to toast the cut side of the bun The two Auxiliary Heaters assist in providing additional heat to the buns The first Auxiliary Heater is located within the Conveyor Belt Chain in the front of the toaster The second Auxiliary Heater is located within the Conveyor Belt Chain at the rear of the unit TEMPERATURE CONTROL NOTE Setpoint Temperature refers to the desired temperature setting Pressing the TEMP UP key will display the current platen temperature provided it is over 420 F 216 C Pressing the TEMP DOWN key will display the current auxiliary heaters temperature when it is over 250 F 121 C Pressing and holding TEMP SCALE key for 3 5 sec onds will switc
17. 2 NOTE Hardware List for items A Z and BB II is on page 24 P N 1010776 Rev 03 06 21 Ap McDonald s A Antunes Foodservice Equipment roundup RAPID TOASTER VCT 250 REPLACEMENT PARTS continued O NOTE Hardware List for items A Z and BB II is on page 24 T Foodservice Equipment McDonald s P N 1010776 Rev 03 06 22 roundup Item Part No 0011266 0800204 0800121 0011264 0800204 0800121 2150117 7000251 7000252 0011242 0011262 0800332 7000207 7000199 7000230 2150118 0700437 Pe ae pur 0700463 7000464 7000465 0700706 15 16 20 7000310 7000296 7000167 21 22 2150181 2150215 2150187 0011299 0501232 0503589 7000364 23 24 25 26 7000240 27 2150112 Description Conveyor Belt Assy Crown A amp B 1 1 2 Pitch Link Small 2 3 4 Pitch Link Large 38 Conveyor Belt Assy Heel A amp B 1 1 2 Pitch Link Small 4 3 4 Pitch Link Large Idler Shaft Conveyor Cover Assy Frnt Heel Club Conveyor Cover Assy Rear Crown Tensioner Assy Front Tensioner Assy Rear Rod Conveyor Cover Sprocket w Setscrew Spacer Kit Pack of 2 Control Cover Incl 48 Drive Shaft Power Cord Plug IEC 309 Mfg No 9210609 Power Cord Plug 5 15P Plug Mfg No 9210600 amp 9210618 Power Cord Plug Twist amp Lock Angle Mfg No
18. 5 C AWM 105 C TERMINAL BLOCK BLK A TRANSFORMER 240VAC 12VAC dldnool HI LIMIT THERMOSTAT P N 1010776 Rev 03 06 27 Ap McDonald s A Antunes Foodservice Equipment RAPID TOASTER VCT 250 Ladder Wiring Diagram POWER SWITCH S S RELAY 2 BASE HEATER AUX HEATER 1 3 4 AUX HEATER 2 AUXILARY S S RELAY 1 EX i CONTROL PLATEN PLATEN T COUPLE PLATEN TEMP CONTROL A 240 VAC J5 1 TRANSFORMER 12 VAC 1 T COUPLE AUXILARY o__C_ e T INTERLOCK SWITCHES roundup 1_ He HI LIMIT THERMOSTAT 28 T Foodservice Equipment P N 1010776 Rev 03 06 McDonald s
19. 9210602 amp 9210620 Power Cord Plug Twist amp Lock Straight Mfg No 9210604 9210612 SBNAS2MANNAANYD amp 9210622 15 Power Cord Plug L6 20P 1 Mfg No 9210619 Only Control Board 1 Ball Bearing Pack of 2 1 Bearing amp Retainer Kit 6 See note below Sprocket Drive w Setscrew 2 Drive Chain For Mfg 9210600 602 1 604 620 and 622 Drive Chain For Mfg 9210609 amp 612 Idler Sprocket amp Bearing Bracket Idler Sprocket Bracket Motor Mounting Drive Motor Kit Incl 78 3 RPM 17 Secs 1 For Mfg 9210600 602 604 618 619 620 and 622 2 2 Drive Motor Kit Incl 78 9 RPM 10 Secs 1 For Mfg 9210609 amp 612 Sprocket Motor w Setscrew 1 28 Tooth 17 Seconds 60Hz Mfg 9210600 602 604 618 619 620 amp 622 Qty Item RAPID TOASTER VCT 250 Part No Description Qty 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 2150129 2150110 4010137 406K006 405K125 4010187 7000183 7000186 0021164 0503496 0503497 1001006 10P1118 10P1026 2100253 7000232 4050214 0021175 7000110 7000111 0021174 7000121 0021183 7000176 2100212 4030332 0400315 0400138 0503405 4030326 0503407 0503590 0700570 0200211 0503425 4030349 4030348 7000165 7000303 7000304 0021182 Sprocket Motor w Setscrew 1 16 Tooth 10 Seconds 60Hz Mfg
20. 9210612 Sprocket Motor w Setscrew 1 20 Tooth 10 Seconds 50Hz Mfg 9210609 Rocker Switch On Off 250 VAC Terminal Block Relay Solid State Transformer Conveyor Belt Wrap Pack of 2 Roller Tensioner Assy Pack of 2 Bun Feeder Tensioner Bracket RH Tensioner Bracket LH Label Control Label Dial Pack of 10 YELLOW Color for Mfg 9210600 602 604 618 619 620 and 622 Label Dial Pack of 10 GRAY Color 1 for Mfg 9210609 amp 612 Knob Control Cover End Thermocouple Assy Platen Weldment End Housing Release Sheet Pack of 3 Release Sheet Pack of 10 Control Housing Slide Rail Kit Includes 2 slide rails for 2 tensioners Conveyor Cam Thermocouple Retainer Kit Lifting Handle High Limit Thermostat Strain Relief Locknut 1 2 Base Outer Heater Bun Landing Base Inner Bracket Motor Wire Set not shown Gasket Base Bun Chute Auxiliary Heater Air 208 VOLT Auxiliary Heater Air 230 VOLT Auxiliary Thermocouple Kit Platen 208 VOLT Platen 230 VOLT Weldment Fan Duct NN a HY NO PH M PO P N 1010776 Rev 03 06 McDonald s 23 T Foodservice Equipment RAPID TOASTER VCT 250 roundup Item Part No Description Qty Item Part No Description Qty 7 63 4000138 Axial Fan 1 79 2100252 Teflon Slip Strip 2 65 4010107 Interlock Switch 2 80 0503448 Damper Support Bracket 2 66 05
21. ICAL SHOCK HAZARD FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS MANUAL COULD RESULT IN SERIOUS INJURY OR DEATH Electrical ground is required on this appliance Do not modify the power supply cord plug If it does not fit the outlet have a proper outlet installed by a qualified electrician Do not use an extension cord with this appliance The toaster should be grounded according to local electrical codes to prevent the possibility of electri cal shock It requires a grounded receptacle with separate electrical lines protected by fuses or cir cuit breaker of the proper rating Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded P N 1010776 Rev 03 06 McDonald s roundup RAPID TOASTER VCT 250 OPERATION Operating Instructions 1 Set the Bun Thickness Adjustment Controls Figure 2A amp 2B as follows For Mfg 9210600 to 9210604 and 9210618 to 9210622 set the Crown control to 5 13 16 20 06 mm For Mfg 9210609 to 9210612 set Crown control to 3 11 16 17 4 mm For Mfg 9210600 to 9210604 and 9210618 to 9210622 set the Heel Club control to D 9 16 14 3 mm For Mfg 9210609 to 9210612 set Heel Club control to B 7 16 11 1 mm 2 Turn the Rocker Switch Power On OFF to ON Figure 3 Allow 30 minutes warm up time before proceeding NOTE The Temperature Display Figure 4 will flash LO until preset
22. T 250 MAINTENANCE continued Install New Release Sheet monthly ACAUTION A Failure to use Release Sheets will result in damage to the unit and loss of warranty coverage 1 Fold a new Release Sheet in half creasing the fold only with your fingers Figure 18 and place it over the Platen Allow the conveyor to draw it into place and verify that it is positioned properly Figure 9 NOTE Use only your fingers to crease the fold DO NOT use any metal wood or plastic devices as they will damage the Release Sheet NOTE Additional Release Sheets can be obtained through your Authorized Service Agency 2 Re install the Bun Feeder and Bun Chute and allow the toaster 30 minutes to warm up Checking Bun Landing Area Temperature IMPORTANT If the toaster is equipped with a Bun Buffer Landing Zone BBLZ you MUST remove the BBLZ BEFORE performing the temperature measurement in Step 1 below This temperature measurement is intended to be taken WITHOUT the BBLZ attached to the toaster 1 Take the temperature of the Bun Landing Area at its center directly in front of the Bun Chute with a Pyrometer Surface Temperature grill Probe The minimum temperature acceptable is 130 F 54 C If it is less contact your Authorized Service Agency or the Technical Service Department of A J Antunes amp Co at 877 392 7854 for the U S amp Canada only or 630 784 1000 2 If a Bun Buffer Landing Zone was removed fro
23. conveyor will stretch This may cause the conveyor to jam as it rotates on the sprock ets This is easily remedied by removing one or more links from each side of the conveyor NOTE This periodic adjustment is not covered under warranty It is a user responsibility 1 Remove the front and rear Conveyor Covers and set the Bun Thickness Compression Controls to 6 amp P 2 Facing the heel club side front locate the approximate center point of the Conveyor Belt Chain 3 Pull the Conveyor Belt Chain away from the edge of the toaster 4 Stand a U S Quarter coin 15 16 2 5 cm horizontally between the chain and the frame Figure 12 NOTE The coin should fit securely between the chain and the frame 5 If the gap is significantly wider than the coin one and a half times as large a small link will have to be removed from the Conveyor Belt Chain 6 Disconnect the Conveyor Belt Chain by squeez ing any two links together and unhooking both ends of one link Figure 13 NOTE Needle nose pliers may be required 7 To shorten a stretched Conveyor Belt Chain remove one 1 2 link from the Conveyor Belt chain 8 Reconnect by hooking both ends of the Conveyor Belt Chain back together and re measure accord ingly NOTE If the chain is too short tight to be reas sembled remove an additional 1 2 link and install a 3 4 link This will shorten the belt 1 4 overall 9 Reassemble the Conveyor Belt Chain
24. e all packing materials when filing a claim Freight damage claims are the responsibility of the purchaser and are not covered under warranty The warranty does not extend to Damages caused in shipment or damage as a result of improper use Installation of electrical service Normal maintenance as outlined in this manual Malfunction resulting from improper maintenance Damage caused by abuse or careless handling Damage from moisture into electrical components Damage from tampering with removal of or changing any preset control or safety device Service Technical Assistance If you experience any problems with the installation or operation of your unit contact your Authorized Service Agency Fill in the information below and have it handy when calling your Authorized Service Agency for assistance The serial number is on the specification plate located on the rear of the unit Purchased From Date of Purchase Model No Serial No Mfg No Refer to the service agency directory packaged with your manual and fill in the information below Authorized Service Agency Name Phone No Address Use only genuine Roundup replacement parts in this unit Use of replacement parts other than those sup plied by the manufacturer will void the warranty Your Authorized Service Agency has been factory trained and has a complete supply of parts for this toaster You ma
25. eel Club side locate the approximate center point of the groovy Belt Pull the conveyor Chain away from the edge of the toaster Stand a U S Quarter 15 16 or 2 5 cm between the frame and the chain If the gap is significantly greater REMOVE links refer to the instructions in the Maintenance section of this manual If you cannot stand a coin in the gap you may have to ADD a link Duplicate this pro cedure for the CROWN side using a U S Dime coin 11 16 or 1 8 cm Adjust the bent Roller Tensioner measured to 13 16 2 1 cm or the height of a U S Nickel coin from the bottom of the roller to the inner cover Note Damaged Roller Tensioners should be replaced Motor Drive Chain is off or dry Have a qualified maintenance person or your Authorized Service Agency reinstall and or lubri cate the chain Motor does not operate Have a qualified maintenance person or your Authorized Service Agency inspect all electrical connections and if necessary replace the motor Groovy Belt wrap stop Underside of Groovy Belt and Clean Belt Wrap and Conveyor Belt Chain as per turning but conveyor Conveyor Chain have excessive current MRC Card TS 019 chain continues to turn caramelizing buildup Flap covering connecting The inner Conveyor Cover has Repair or replace the inner conveyor cover hinge or wavy rib on Belt been damaged bent in at the top Wrap is getting torn or Groovy Belt Wrap ha
26. fg 9210609 to 9210612 set the controls to B amp 3 T Foodservice Equipment RAPID TOASTER VCT 250 roundup MAINTENANCE continued Monthly Bun Temperature Test NOTE The minimum temperature allowed is 150 F 65 6 C If this temperature is not achieved con tact your Authorized Service Agency Tools Required Pyrometer Needle probe attachment four 8 oz coffee cups stacked together plus one lid or four 12 oz coffee cups plus one lid 1 Turn the ON and preheat for 30 minutes 2 Toast 3 regular buns to be used with the 8 oz cup stack or 4 regular buns to be used with the 12 oz cup stack 3 Immediately stuff the buns into the stacked cups and tightly apply the lid Wait 10 minutes 4 Insert the needle probe attachment of the pyrometer through the lid several times Note the maximum temperature Monthly Replace Release Sheet Every Three Months Replace Groovy Belt Wraps Clean and Measure Conveyor Belt Chains Check Roller Tensioners and Check Temperature of Bun Landing Area Remove the Groovy Belt Wraps amp Release Sheet 1 Turn the unit OFF unplug the toaster and allow it to cool down 2 Remove the Bun Feeder Bun Chute and change the Bun Thickness Compression Controls to F amp 6 Figure 2A 2B 3 Remove and discard the black Release Sheet 4 Open the Front Heel Club Conveyor Cover and rotate the Groovy Belt Wrap so its flap is in the middle top to bottom of the conveyor
27. h the temperature display between Fahrenheit F and Celsius C RECOMMENDED TEMPERATURES Recommended temperature setting for the Platen Heater is 560 F 293 C Recommended temperature setting for the Auxiliary Heaters is 400 F 204 C NOTE The toaster is tested and shipped with the heaters set at the above recommended tempera tures PLATEN SETPOINT TEMPERATURE ADJUSTMENT 1 Turn the Rocker Switch Power On Off to ON and wait for the Temperature Display to finish the power up sequence Figure 4 2 Press and hold both TEMP UP and TEMP DOWN keys until the display flashes the platen setpoint temperature then release 3 Press the TEMP UP or the TEMP DOWN key to raise or lower the setpoint temperature The setpoint temperature will adjust 1 every 0 1 seconds 4 Release the key when the desired setpoint is displayed NOTE Maximum adjustable setpoint temperature for the platen is 600 F 315 C T Foodservice Equipment roundup OPERATION continued Heat On LED will blink on off during warm up and when either platen or auxiliary heaters are calling for heat OO TEMP TEMP TEMP UP DOWN SCALE POWER E j TEMP TEMP TEMP UP DOWN SCALE 1 SP P Setpoint Platen is displayed TEMP TEMP TEMP UP DOWN SCALE 3 SP A Setpoint Auxiliary is displayed 2 Current Platen Temperature setting is shown TEMP TEMP TEMP UP DOWN SCALE 4 Current Au
28. he con trol circuits if the unit overheats To reset this hi limit control allow sufficient time 10 15 minutes for the unit to cool down then depress the reset button located on the rear of the unit Figure 5 If the unit requires continuous resetting contact your Authorized Service Agency FAULT MESSAGES Ifthe Platen Thermocouple is disconnected or open the display will flash and the Platen heating circuit will turn off Figure 6 The Platen Thermocouple must be reattached or replaced Ifthe Platen Heater temperature exceeds 620 F 327 C the display will flash and the heating circuit will turn off Figure 6 After the toaster has cooled down the unit must be turned off then back on to restart If this condition repeats contact your Authorized Service Agency If the Auxiliary Heating temperature exceeds 420 F 215 C the display will alternately flash HI and USE Figure 8 The heating circuit will not turn off After the toaster has cooled down the unit must be turned off then back on to restart If this condition repeats contact your Authorized Service Agency P N 1010776 Rev 03 06 McDonald s Hi Limit Reset Protective Screw Cap Figure 5 Hi Limit Reset HI displayed if platen temperature exceeds 620 F 327 C or if platen thermocou ple is disconnected or open Heating circuit will turn off and
29. l the new Groovy Belt Wraps with the Hinge uad Yellow Su Flap hanging down and the wavy lines facing out as shown in Figure 16 Figure 14 Replacing Groovy Belt CAUTION Be sure Groovy Belt Wrap ends are aligned as shown in Figure 16 or damage to the Belt Wrap will occur NOTE The Groovy Belt Wraps must be installed inside the yellow Support Rods The flap which covers the connecting hinge is located on the wavy side of the belt The wavy side should be installed facing the outside of the toaster The flap should be in the down position Figures 14 amp 16 1 CAUTION A Be sure the Groovy Belt Wrap is positioned INSIDE INCORRECT CORRECT the upper and lower yellow Support Rods or damage to the Groovy Belt Wraps will occur Figure 15 Aligning Belt Teeth 3 Close the front and rear Conveyor Covers by lift ing the covers and gently pushing upward and into the toaster until the covers latch onto the yel low Support Rods Belt Rotation Direction of Travel NOTE Make sure both Conveyor Safety Interlock Switches are activated when the covers are installed Figure 11 or the conveyors will not rotate Horizontal Rib Installed to the INSIDE Wavy Rib Installed to the OUTSIDE Figure 16 Correct Groovy Belt Wrap Installation AP 14 P N 1010776 Rev 03 06 McDonald s Antunes Foodservice Equipment roundup RAPID TOASTER VC
30. le Inoperable Control Board Contact your maintenance person or Temperature display flashes HI and Auxiliary Thermocouple is discon Authorized Service Agency LO at cold startup nected or open After preheat time display flashes HI and USE Temperature display flashes HI and Auxiliary circuit overheating due to USE after unit has been preheated auxiliary solid state relay shorted and Belt Wraps may start to smoke closed Display reads CHEC Ambient temperature in control com Turn toaster off and allow control partment too high compartment to cool down to 140 F 60 C and restart toaster Be sure cooling fan is operating and nothing is blocking the flow of cooling air to the bottom of the toaster McDonald s Antunes Foodservice Equipment Pound api TOASTER vcr 250 TROUBLESHOOTING continued Conveyor Belt Chain does Compression Knobs set incor Set the Bun Thickness Compression Controls to not turn or skips sprock D amp 5 for Mfg 9210600 602 604 618 619 ets 620 amp 622 For Mfg 9210609 to 9210612 set the controls to B amp 3 See Figures 2A and 2B Interlock Switches not activating Verify the covers are installed correctly Repair or replace damaged conveyor inner cover Switches are inoperable Contact your mainte nance person or Authorized Service Agency Conveyor Chain is stretched Open Conveyor covers Set compression Knobs to 6 and F Facing the H
31. les 80 km 1 hour each way 100 miles 160 km 2 hours round trip WARRANTY EXCLUSIONS Scheduled Maintenance procedures as outlined in your MRC Card The cost of Installation Consumables such as Grill Covers Release Sheets gaskets Conveyor Belt Equipment that has been damaged due to shipment Purchaser should Wraps O Rings and light bulbs make damage claim directly upon carrier Alteration misuse abuse Overtime or Holiday charges Mileage over 50 miles 80 km 100 miles 160 km round trip or travel time Improper storage or handling over two 2 hours mproper maintenance Freight foreign excise municipal or other sales or use taxes Failure to follow proper Installation instructions including electrical connec Consequential damages such as loss of profit loss of time the cost of repair tion ing or replacing other property which is damaged or any other incidental mproper or unauthorized repairs damage of any kind Antunes Food Service reserves the right to make changes in design or add improvements on any products The right is always reserved to modify Equipment because of factors beyond our control and government regulation Changes to Equipment do not constitute a warranty charge This warranty is exclusive and is in lieu of all other warranties expressed or implied including any implied warranty of merchantability or fitness for a particular pur pose each of which is expressly disclaimed The re
32. m the toaster in Step 1 re attach it after completing Step 1 Adjusting Measuring and or Replacing Roller Tensioner Assemblies NOTE Measure the Roller Tensioners They should be 13 16 2 1 cm or the height of a U S Nickel coin from the bottom of the roller to the inner Conveyor Cover Figure 18 and adjust or replace them accordingly If they have been damaged they should be replaced 1 Remove screws from acorn nuts Figure 19 and remove the old Roller Tensioner assembly P N 1010776 Rev 03 06 McDonald s 2 Replace Roller Tensioner assembly and reas semble 3 Make sure the spacers are placed inside the tensioner arm The spacers are smaller than the holes to allow the tensioner to pivot freely 4 Setthe Bun Thickness Compression Controls to D amp 5 for Mfg 9210600 to 9210604 9210618 to 9210622 For Mfg 9210606 to 9210612 set the controls to B amp 3 Plug in the power cord and turn unit on NOTE Refer to Figures 2A and 2B in the Operation section of this manual 2 n Lay sheet on a fla Du ce surface Fold over so ends meet Press lightly with finger to form crease Figure 17 Folding Release Sheet Teflon Tape Tensioner Assy Screw b VN ZR E V d gt 01 2 Spacer 27 Rear Conveyor Cover Assy Figure 19 Replacing Roller Tensioner Assembl
33. medies described above are exclusive and in no event shall A J Antunes amp Co or any of its Divisions be liable for special consequential or incidental damages for the breach or delay in the performance of this warranty This manual is for the exclusive use of licensees and employees of McDonald s Systems Inc McDonald s Corporation All Rights Reserved P N 1010776 Rev 03 06 1 Ap McDonald s Antunes Foodservice Equipment RAPID TOASTER VCT 250 roundup OWNER INFORMATION General This manual is produced for the Rapid Toaster The Rapid Toaster is designed for contact toasting of buns This design allows the operator to place buns on both sides of the heated Platen at the same time Buns are placed into the Bun Feeder on the top of the toaster and uniform golden brown warm buns are then retrieved at the base of the toaster This manual provides the safety installation and oper ating procedures for the Rapid Toaster We recom mend that this manual be read prior to installing and operating the unit The Rapid Toaster is manufactured from the finest materials available and is assembled to Roundup s strict quality standards This unit has been tested at the factory to ensure dependable trouble free opera tion Warranty Information Please read the full text of the Limited Warranty in this manual If the unit arrives damaged contact the carrier imme diately and file a damage claim with them Sav
34. r Cover and repeat this procedure on the second rear Crown side Groovy Belt Wrap NOTE Do not remove Groovy Belt Wrap from unit 5 Plug in the power cord and turn the unit ON count seventeen 17 seconds for Mfg 9210600 to 9210604 and 9210618 to 9210622 or ten 10 seconds for Mfg 9210609 to 9210612 Then turn the unit OFF and unplug the power cord Repeat Step 4 again on both Groovy Belt Wraps Heat Dampers and the surface of the Inner Conveyor Covers NOTE Make sure both Conveyor Safety Interlock Switches are activated when the covers are installed Figure 11 or conveyors will not rotate 6 Plug the power cord in and turn on the unit fold the Release Sheet in half and place it over the Platen Allow it to be drawn into place and posi tioned properly P N 1010776 Rev 03 06 McDonald s 11 Bun Chute Bun Feeder Clip Bun Feeder Release Sheet Figure 9 Removing Installing Release Sheet Figure 10 Conveyor Cover Installation NOTE Check the release sheet to make sure it is not caught in the conveyor T Turn the unit OFF and re install the Bun Feeder and Bun Chute Wipe the entire exterior surface to the toaster with a clean dry towel dampened with KAYQUAT Sanitizer HCS and allow it to air dry Verify that the Bun Thickness Compression Controls are set to D amp 5 for Mfg 9210600 to 9210604 9210618 to 9210622 For M
35. s been Reinstall Groovy Belt Wrap with flap down wom installed upsidedown Groovy Belt Wraps are Missing or Bent Roller Tensioners Replace or adjust the bent Roller Tensioner tearing in the center A measured to 13 16 2 1 cm or the height of a U S Nickel coin from the bottom of the roller to the inner cover P N 1010776 Rev 03 06 17 McDonald s A Antunes Foodservice Equipment RAPID TOASTER VCT 250 roundup TROUBLESHOOTING continued Groovy Belt Wrap Groovy Belt Wrap is installed Check that Groovy Belt Wrap is not placed over the does not fit is difficult improperly upper or lower Support Rod Be sure the open end to install or is not long of the flap is away from direction and rotation and is enough located toward the outside of the Groovy Belt Wrap Groovy Belt Wrap is damaged Replace Groovy Belt Wrap The only item that Hi Limit Control is tripped open Reset Hi Limit Control according to the instructions in operates is the cool the Maintenance section of this manual ing fan conveyor and heat inoperable Note If Hi Limit trips again contact your Authorized Service Agency for service Platen is hot and Conveyor Cover assemblies not Install Conveyor Cover assemblies Conveyor Belt Chains installed do not move Conveyor Belt Chains installed Install Conveyor Belt Chain to match the diagram incorrectly One or both Conveyor Interlock Install Conveyor Cover assembly correctly see Figure
36. t this manual and should be carefully observed Turn the unit off disconnect the power source and allow unit to cool down before performing any service or maintenance on the unit The procedures in this chapter may include the use of chemical products These chemical products will be highlighted with bold face let ters followed by the abbreviated HCS Hazard Communication Standard See Hazard Communication Standard manual for the appro priated Material Safety Data Sheets MSDS The equipment should be grounded according to local electrical codes to prevent the possibility of electrical shock It requires a grounded recep tacle with separate electrical lines protected by fuses or circuit breaker of the proper rating Bread may burn Therefore toasters must not be used near or below curtains or other combustible walls and materials Failure to maintain safe operating distances may cause discoloration or combustion T Foodservice Equipment RAPID TOASTER VCT 250 roundup INSTALLATION Unpacking 1 Remove unit and all packing materials from shipping carton 2 Open the accessory box It should contain the following Bun Chute Figure 1 Bun Feeder Figure 1 Plastic bag containing the Release Sheets not shown 3 Remove all packing materials and protective coverings from the unit and parts NOTE If any parts are missing or damaged con tact A J Antunes Technical Service IMMEDIATELY at 1 877
37. tion of this manual Defective Drive Chain or loose Contact your maintenance person or sprocket Authorized Service Agency Defective Drive Motor or wrong RPM Drive Motor Defective temperature display control Product is under toasted Temperature set too low Reset platen temperature to or Platen heat is too low Compression Knobs set incorrectly Set the Bun Thickness Compression drop time is too fast Controls to D amp 5 for Mfg 9210600 602 604 618 619 620 amp 622 For Mfg 9210609 to 9210612 set the controls to B amp 3 See Figures 2A and 2B Contact your maintenance person or squeal or whining noise motor replace it P N 1010776 Rev 03 06 19 McDonald s A Antunes Foodservice Equipment RAPID TOASTER VCT 250 roundup REPLACEMENT PARTS 74 93 id Sy wu For Mfg 9210600 an 27 Qe MS 602 604 618 620 and 622 only For Mfg 9210618 620 amp 622 only NOTE Hardware List for items A Z and BB II is on page 24 McDonald s Antunes Foodservice Equipment roundup RAPID TOASTER VCT 250 REPLACEMENT PARTS continued oS LSG 9210600 9210602 9210604 9210609 9210612 26 9210618 9210620 amp 921062
38. tion of this manual McDonald s Antunes Foodservice Equipment roundup 25 TROUBLESHOOTING continued Buns sticking Compression Knobs set incorrectly Set the Bun Thickness Compression Controls to D amp 5 for Mfg 9210600 602 604 618 619 620 amp 622 For Mfg 9210609 to 9210612 set the controls to B amp 3 See Figures 2A and 2B Improper cleaning of the Release Follow the cleaning and or replacement Sheet and or Groovy Belt Wrap instructions on the current MRC Card TS 019 and immediately clean the APSC off with a clean dry towel dampened with sanitizer solutions Roller Tensioner out of position Adjust or replace Roller Tensioner according to the instructions in the Maintenance section of this manual Note Replace damaged Roller Tensioners Product is over toasted or Temperature set too high Reset Platen temperature to 560 F 293 C Platen Heat is to high or Bun adjustment controls set incor Set bun adjustment controls according to the drop time is too slow rectly instructions in the Operations section of this manual Groovy Belt Wraps worn and not Clean or replace Groovy Belt Wrap permitting belt to pull buns across Platen in required time Groovy Belt not tacky Buns sticking on Release Sheet Clean or replace Release Sheet Groovy Belt installed incorrectly Re install Groovy Belt according to the instructions in the Maintenance sec
39. xiliary Temperature setting is shown TEMP TEMP TEMP UP DOWN SCALE 5 LO is displayed until platen temperature rises above 520 F 271 C Platen setpoint temperature must be between 520 F 271 C and 590 F 310 for USE to be displayed use ji TEMP TEMP TEMP UP DOWN SCALE 6 USE is displayed when Platen Setpoint Temperature is reached Figure 4 Temperature Power Up Sequence P N 1010776 Rev 03 06 McDonald s roundup RAPID TOASTER VCT 250 OPERATION continued NOTE If no change is made within 5 seconds the display will revert back to the previous setpoint AUXILIARY HEATER TEMPERATURE ADJUSTMENT 1 Turn the unit ON and wait for temperature display to finish the power up sequence Figure 4 num bers 3 amp 4 2 Press and hold both TEMP UP and TEMP SCALE keys until the display flashes the auxiliary setpoint temperature then release Figure 4 number 3 3 Press the TEMP UP or TEMP DOWN key to raise or lower the setpoint temperature The setpoint temperature will adjust 1 every 0 5 seconds 4 Release the key when the desired setpoint is displayed NOTE Maximum adjustable setpoint temperature for the Auxiliary Heater is 400 F 204 C NOTE If no change is made within 5 seconds the display will revert back to the previous setpoint Safety Features HI LIMIT RESET BUTTON A hi limit control will turn off electrical power to t
40. y T Foodservice Equipment RAPID TOASTER VCT 250 roundup AWARNING To avoid possible personal injury and or damage to the unit inspection test and repair of electrical equipment should be performed by qualified service personnel The unit should be unplugged when servicing except when electrical tests are required Use extreme care during electrical circuit tests Live circuits will be exposed Possible Cause Corrective Action No Display Unit not plugged in Connect toaster to proper recep No light on Power Switch tacle Hi Limit tripped Reset Hi Limit Circuit Breaker tripped Reset Circuit Breaker Power Cord and or plug are dam Contact your maintenance person or aged Authorized Service Agency Inoperable Rocker Switch power On Off Temperature display flashes PO Voltage to the unit is below 190 Turn the Rocker Switch power On volts Off to OFF then ON If the display shows PO again check the power cord and plug receptacle for dam age Reset Circuit Breaker located at store s power panel Contact your maintenance person or Authorized Service Agency Temperature display reads LOW Platen temperature is below 420 F Allow thirty minutes for warm up and 216 C recheck display Contact your maintenance person or Authorized Service Agency Temperature display flashes at Platen Thermocouple is disconnect Re attach or replace Platen cold start ed or open Thermocoup
41. y also contact the factory at 1 877 392 7854 North America only or 630 784 1000 if you have trouble locating your local Authorized Service Agency To locate your nearest International Authorized Service Agency log onto the McDonald s web site www mcdonalds com and follow the on screen direc tions IMPORTANT Keep these instructions for future reference If the unit changes ownership be sure this manual accompanies the equipment T Foodservice Equipment P N 1010776 Rev 03 06 McDonald s roundup RAPID TOASTER VCT 250 SPECIFICATIONS Model Designation Electrical Cord amp Plug Configurations VCT 250XX TYPE OF POWER CORD H HARMONIZED C COMMERCIAL R ROCKBESTOS TYPE OF PLUG C 7 7 D Domestic Pin and Sleeve International Pin and Sleeve R Right Angle Twist Lock S Straight Twist Lock U Straight Twist Lock Toasting Time Change In Early 2003 there was a change in the toasting time and Bun Thickness settings The toasting time was changed from 10 seconds to 17 sec onds and the Bun Thickness settings were changed from B amp 3 to D amp 5 This field Toaster Quality Kit was installed on models VCT 250RD Mfg 9210600 VCT 250RR Mfg 9210602 and VCT 250RS Mfg 9210604 Not all toasters were changed to the 17 second toasting time To determine if your toaster is a 10 or 17 second toaster look
Download Pdf Manuals
Related Search