PERIODIC MAINTENANCE
Contents
1. and the shim is 170 1 70 mm select 195 1 95 mm of the shim which 170 1 70 mm of the shim add up the excess clearance 0 25 mm when adjust with the standard 0 15 as the intake standard clearance 0 1 0 2 mm AA CAUTION Valve clearance should be checked when the engine is cold LS D Q a d S E me at_ i If you don t rotate the crankshaft about 10 times before measuring the valve clearance there is no meaning of valve clearance 2 5 PERIODIC MAINTENANCE Rotate the magneto rotor to set the rear cylinder s piston at TDC Top Dead Center of the compression stroke Rotate the rotor 285 counter clockwise from the F line and until the R line on the rotor is aligned with the center of hole on the crankcase Inspect the rear cylinder s valve clearance with the same manner of the front cylinder SPARK PLUG NOTE Clean Initial 1 000 km and Every 4 000 km Replace Every 8 000 km Disconnect the spark plug caps Remove the spark plugs TYPE SPARK PLUG SPECIFICATION Hot type CR7E Standard type CR8E Cold type CR9E Remove the carbon deposite with wire or pin and adjust the spark plug gap to 0 7 0 8 mm measuring with a thickness gauge Spark plug gap 0 7 0 8 mm Thickness gauge 09900 20806 Check to see the worn or burnt condition of the elec trodes If it is extremly worn or burnt replace the plug And also replace the2. plug if it has a broken insulator damaged thread etc install the spark plug and then tighten it to specified torque II Spatk plug 20 25 N m 2 0 2 5 kg m 0 7 0 8 mm EXHAUSE PIPE NUTS AND MUFFLER MOUNTING BOLTS NOTE Tighten Initial 1 000 km and Every 4 000 km Tighten the exhaust pipe nuts and muffler mount ing bolts to the specified torque 8 Exhaust pipe nut 18 28 N m 1 8 2 8 kg m Muffler mounting bolt 20 30 N m 2 0 3 0 kg m AIR CLEANER NOTE Clean Every 3 000 km Replace Every 12 000 km Remove the air cleaner case cover PERIODIC MAINTENANCE 2 6 HYQSUNG 2 7 PERIODIC MAINTENANCE With the three of air cleaner cap mounting bolts removed remove the air cleaner cap 1 Remove the air cleaner element Clean the air cleaner element for the following When the air cleaner element clean with the air gun necessarily blow at the inside by compressed air Carefully examine the air cleaner element for tears during Cleaning Replace it with a new one if it is torn Assemble the element completely or damage severely the engine Be careful not to allow water to go inside the air clea ner element AA CAUTION More frequent servicing may be performed on mo torcycles that are used under severe conditions also clean the air cleaner element when replacing the oil to prevent damage of the engine CARBURETOR N
3. tank Refer to page 4 1 Remove the cylinder head cover and Remove the magneto cover plug and the timing inspection plug PERIODIC MAINTENANCE 2 4 Rotate the magneto rotor to set the front cylinder s piston at TDC Top Dead Center of the compression stroke Rotate the rotor until F line on the rotor is aligned with the center of hole on the crankcase To inspect the front cylinder s valve clearance insert the thickness gauge to the clearance between the camshaft and the tappet Valve clearance when cold Thickness gauge 09900 20806 if the clearance is out of specification first remove the cam chain tensioner camshaft housing camshaft To install the tappet shim at original position record the shim NO and clearance with A B C D mark on the cylinder head as the illustration Select the tappet that agree with tappet clearance vertical line and shim NO horizontal line as refer to the tappet shim selection chart Refer to page 7 25 26 Adjust valve timing install the camshaft housing and the tensioner After the crankshaft rotate about 10 times measure the valve clearance If the clearance be not agree adjust the standard clea rance as the same manner above in case that valve adjustment which there is no the tappet shim selection chart please follow instructions of example in the below For example the intake clearance is 0 4
4. the Lower line mark L in the engine oil level gauge Never fill the engine oil above the Up per line mark F Engine oil level being most suitable about 1mm under the Upper line mark F of the engine oil lens In case of the engine oil pouring in excessively the engine output being made insufficient Be careful not to pouring in the engine oil exces sively 4 CAUTION Necessarily confirm and clean the oil strainer when replace the Engine oil specially when first replacement 4 CAUTION More frequent servicing may be performed on mo torcycles that are used under severe conditions PERIODIC MAINTENANCE 2 10 2 11 PERIODIC MAINTENANCE ENGINE OIL FILTER NOTE Replace Initial 1 000 km and Every 4 000 km Drain the engine oil as described in the engine oil replacement procedure Remove the oil filter cap Remove the oil filter Install the new O ring Install the new oil filter Install the new O ring and spring to the oil filter cap Install the oil filter cap NOTE Before installing the oil filter cap apply engine oil lightly to the new O ring 3 OIL FILTER INSTALLATION AA CAUTION When install the oil filter necessarily HYOSUNG character and 16510H05240 parts NO install to ward the outside otherwise can damage the engine WARNING Engine oil and exhaust pipes can be hot enough to burn you Wait until the oil drain plug and exhaus
5. 20 pitch length Loosen or tighten both chain adjusters until the chain has 20 30 mm of slack in the middle between the engine and rear sprockets The marks 3 on both chain adjusters must be at the same position on the scale to ensure that the front and rear wheels are correctly aligned Drive chain slack 20 30mm Place the motorcycle on jack or block for accurate adjustment After adjusting the drive chain tighten the axle nut to the specified torque Tighten both chain adjusters securely DI Rear axle nut 90 140 N m 9 0 14 0 kg m Recheck the drive chain slack after tightening the axle nut 123 192021 Yo oxo ot FeO ato aye ako Yo ofo glo efo YL p T i 1 H i 5 EE t sz J Wash the drive chain with kerosine If the drive chain tends to rust quickly the intervals must be shortened After washing and drying the chain oil it with a engine oil CAUTION s The standard drive chain is a RK 520DS Hyo sung recommends that this standard drive chain should be used for the replacement BRAKE SYSTEM NOTE BRAKE Inspect Initial 1 000 km and Every 4 000 km BRAKE HOSE amp BRAKE FLUID Inspect Initial 1 000 km and Every 4 000 km Replace the brake hoses Every 4 years Replace the brake fluid Every 2 years BRAKE FLUID LEVEL CHECK Keep the motorcycle upright and place the handle bars straight Check the brake fluid level by observing
6. CONTENTS PERIODIC MAINTENANCE SCHEDULE nnn 2 4 PERIODIC MAINTENANCE CHART oeeeeeeeeeeeeeeeeeeeeereeeee 9 14 LUBRICATION el EE 9 2 MAINTENANCE PROCEDURES et 23 WAIVE CLEARANCE Anan ENEE E 23 SPARK PLUC E 25 EXHAUST PIPE NUTS AND MUFFLER MOUNTING POTS 2 6 ARCOLAN R ooe E E E eee 26 EREECHEN eege 2 8 PUG HOSE ee 2 8 CL UTON EE 9 9 ENGINE e iss or nE E 9 9 ENGINE OIL BIRT cree TE EE 2 11 DRIVE ag EI EE 9 12 BRAKE SVS zeegt 9 14 STEERING eege 9 18 SESCH 9 18 REAR SUSPENSION seeps eee re eee 9 18 e E 2 19 CHASSIS BOLTS AND NUTS eeeeeeeeeereecereeerrr 2 19 COMPRESSION PRESSURE eeeeeeeeeerererrrrrr 2 20 OIL PRESSURE E 2 21 PERIODIC MAINTENANCE 2 1 PERIODIC MAINTENANCE PERIODIC MAINTENANCE SCHEDULE The chart below lists the recommended intervals for all the required periodic service work necessary to keep the motorcycle operating at peak performance and economy AA CAUTION More frequent servicing should be performed on motorcycles that are used under severe conditions PERIODIC MAINTENANCE CHART ENGINE Air Aircleanerelement element Clean every 3 000 km Replace every 12 000 km de DEE pipe nuts and Tigh Im 1 mg Fuel hose Replace every 4 years Coen 1 bois emp CHASSIS Drivechain chain Clean and lubricate every 1 000km A 12 EE rem mm Brake hose Replace every 4 years inspect Im o oo Brake fluid Replace every 2 years Chassis bolts and nuts Tighten Tighten AA CAUTION Using poor q
7. NT Place the motorcycle on a level surface and keep the handlebars straight Remove the master cylinder reservoir cap and diaphragm Suck up the old brake fluid as much as possible Fill the reservoir with new brake fluid Specification and Classification DOT 3 or DOT 4 Connect a clear hose 1 to the air bleeder valve and insert the other end of the hose into a receptacle Loosen the air bleeder valve and pump the brake lever until the old brake fluid is completely out of the brake system Close the air bleeder valve and disconnect the clear hose Fill the reservoir with new brake fluid to the upper line BT Front brake caliper air bleeder valve 6 9 N m 0 6 0 9 kg m AIR BLEEDING OF THE BRAKE FLUID CIRCUIT Air trapped in the brake fluid circuit acts like a cushion to absorb a large proportion of the pressure developed by the master cylinder and thus interferes with the full brak ing performance of the brake caliper The presence of air is indicated by sponginess of the brake lever and also by lack of braking force Considering the danger to which such trapped air exposes the machine and rider it is essential that after remounting the brake and restoring the brake system to the normal condition the brake fluid circuit be purged of air in the following man ner Fill the master cylider reservoir to top of the inspec tion window Replace the reservoir cap to prevent dirt from ent
8. OTE Inspect Initial 1 000 km and Every 4 000 km IDLE SPEED 4 CAUTION Make this inspection when the engine is hot Connect an engine tachometer to the high tension cord Start up the engine and set its speed at anywhere 1 450 and 1 550 rpm by turning throttle stop screw Q Engine idle speed 1 450 1 550 rom Engine tachometer 09900 26006 THROTTLE CABLE PLAY There should be 0 5 1 0 mm play on the throttle cable To adjust the throttle cable play Tug on the throttle cable to check the amount of play Loosen the lock nut and turn the adjuster in or out until the specified play is obtained Secure the lock nuts while holding the adjuster in place Throttle cable play 0 5 1 0 mm FUEL HOSE NOTE Inspect Initial 1 000 km and Every 4 000 km Replace every 4 years Remove the left frame cover Refer to page 6 3 Inspect the fuel hoses for damage and fuel leakage If any defects are found the fuel hoses must be replaced PERIODIC MAINTENANCE 2 8 2 9 PERIODIC MAINTENANCE CLUTCH NOTE Inspect Initial 1 000 km and Every 4 000 km Clutch play should be 4 mm as measured at the clutch lever holder before the clutch begins to disengage If the play in the clutch is incorrect adjust it in the following way Loosen the lock nut and screw the adjuster on the clutch lever holder all the way in Loosen clutch cable adjuster lock nut Turn the clutch cable adjuster i
9. ering it Attach a hose to the air bleeder valve and insert the free end of the hose into a receptacle Bleed air from the brake system Squeeze and release the brake lever several times in rapid succession and sqeeze the lever fully without releasing it Loosen the bleeder valve by turning it a quarter of a turn so that the brake fluid runs into the receptacle this will remove the tension of the brake lever causing it to touch the handlebar grip Then close the air bleeder valve pump and squeeze the brake lever and open the valve Repeat this process until the fluid flowing into the receptacle no longer contains air bubbles PERIODIC MAINTENANCE 2 16 Upper limit line 2 17 PERIODIC MAINTENANCE NOTE While bleeding the brake system replenish the brake fluid in the reservoir as necessary Make sure that there is always some fluid visible in the reservoir Close the air bleeder valve and disconnect the hose Fill the reservoir with brake fluid to the upper line IT Front brake caliper air bleeder valve 6 9 N m 0 6 0 9 kg m AA CAUTION Handle brake fluid with care the fluid reacts chemically with paint plastics rubber materials etc REAR BRAKE PEDAL HEIGHT Loosen the lock nut Adjust the brake pedal height by turning the adjuster Rear brake pedal 310 mm height A When one person ridding at the ground REAR BRAKE ADJUSTING Adjust the free travel B to 20 30 mm by turni
10. is bolts and nuts are tightened to their specified torque Refer to page 7 12 Tire wear indicator COMPRESSION PRESSURE The compression of a cylinder is a good indicator of its internal condition The decision to overhaul the cylinder is often based on the results of a compression test Periodic maintenance records kept at your dealership should include compres sion reading for each maintenance service Compression pressure Standard 14 16 kg cm at 600 rpm Low compression pressure can indicate any of the fol lowing conditions Excessively worn cylinder wall Worn down piston or piston rings Piston rings stuck in grooves Poor seating of valves Ruptured or otherwise defective cylinder head gasket COMPRESSION TEST PROCEDURE NOTE Before testing the engine for compression pres sure make sure that the cylinder head bolts are tightened to the specified torque values and valves are properly adjusted Have the engine warmed up by idling before testing a Be sure that the battery used is in fully charged condition Remove the parts concerned and test the compression pressure in the following manner Loosen the oil cooler mounting bolts from the frame Remove all the spark plug Fit the compression gauge in one of the plug holes while taking care that the connection is tight Keep the throttle grip in full open position Crank the engine a few seconds with the s
11. n or out to acquire the specified play Tighten lock nut while holding the adjuster in position The clutch cable should be lubricated with a light weight oil whenever it is adjusted Clutch cable play 4 mm Gei GEARSHIFT LEVER HEIGHT ADJUSTMENT Loosen the lock nut With the link rod turned adjust the gearshift lever height ENGINE OIL NOTE Replace Initial 1 000 km and Every 4 000 km Necessary amount of engine oil Oil change 1 450 ml Filter change 1 500 ml Overhaul engine 1 800 m Engine oil type SAE 10W40 API SF or SG Oil should be changed while the engine is warm Oil fil ter replacement at the above intervals should be together with the engine oil change Keep the motorcycle upright Place an oil pan below the engine and drain the oil by removing the filter cap and drain plug Tighten the drain plug to the specified torque and pour fresh oil through the oil filter Use an API classi fication of SF or SG oil with SAE 10W40 viscosity IT Oil drain plug 18 20 N m 1 8 2 0 kg m Start up the engine and allow it to run for several minutes at idling speed Turn off the engine and wait about three minutes then check the oil level through the inspection win dow If the level is below mark F add oil to F level If the level is above mark F drain oil to F level AA CAUTION Never operate the motorcycle if the engine oil level is below
12. ng the adjusting nut Rear brake pedal free travel 20 30 mm REAR BRAKE SHOE WEAR This motorcycle is equipped with brake lining wear limit indicator on the rear brake To check brake lining wear perform the following steps Make sure that the rear brake is properly adjusted Depress the rear brake pedal Make sure that the extension line 3 from the index mark is within the range 4 embossed on the brake panel If the extension line goes beyond the range the brake shoe assembly should be replaced with a new set of shoes Refer to page 6 39 Upper limit line wf o St BRAKE LAMP SWITCH Adjust the rear brake lamp switch so that the brake lamp will come on just before pressure is felt when the brake pedal is depressed STEERING NOTE Inspect Initial 1 000 km and Every 4 000 km Steering should be adjusted properly for smooth turning of handlebars and safe running Overtight steering pre vents smooth turning of the handlebars and too loose steering will cause poor stability Check that there is no play in th steering stem while grasping the lower fork tubes by supporting the machine so that the front wheel is off the ground with the wheel straight ahead and pull forward If play is found perform steering bearing adjustment as described in page 6 30 of this manual FRONT FORK NOTE Inspect Every 4 000 km Inspect the front forks for oil leakage scoring or scratch es on the oute
13. r surface of the inner tubes Replace any defective parts if necessary REAR SUSPENSION NOTE Inspect Every 4 000 km Inspect the rear shock absorber for oil leakage and mounting rubbers including engine mounting for wear and damage Replace any defective parts if neces sary Refer to page 6 43 PERIODIC MAINTENANCE 2 18 2 19 PERIODIC MAINTENANCE TIRE NOTE Inspect Initial 1 000 km and Every 4 000 km TIRE TREAD CONDITION Operating the motorcycle with excessively worn tires will decrease riding stability and can lead to loss of control Inspect stortage of tire thread s depth by the tire wear indicator Replace the front and rear tires at once when appear the tire wear indicator TIRE PRESSURE lf the tire pressure is too high or too low steering will be adversely affected and tire wear increased Therefore maintain the correct tire pressure for good roadability or shorter tire life will result Cold inflation tire pressure is as follows COLD INFLATION SOLD RIDING DUAL RIDING TIRE PRESSURE KPa SC 1721 75 25 172 1 75 25 1962 00 29 221 2 25 32 AA CAUTION The standard tire on Agra 250 is 110 90 16 59S for front and 150 80 15M C 70S for rear The use of tires other than those specified may cause instability It is highly recommended to use a HYOSUNG Genuine Tire CHASSIS BOLTS AND NUTS NOTE Tighten Initial 1 000 km and Every 4 000 km Check that all chass
14. t pipes are cool enough to touch with bare hands before drain ing oil INSERTION DIRECTION 16510H05240 LUSTER MATERIAL OUTSIDE Add new engine oil and check the oil level as described in the engine oil replacement procedure AA CAUTION Use HYOSUNG MOTORCYCLE GENUINE OIL FIL TER only since the other make s genuine filters and after market parts may differ filtering perfor mance and durability which could cause engine damage or oil leaks Hyosung motors genuine oil filter is also not usable for the motocycles DRIVE CHAIN NOTE Clean and Lubricate Every 1 000 km Visually check the drive chain for the possible defects listed below Support the motorcycle by the jack or block turn the rear wheel slowly by hand with the trans mission shifted to Neutral Loose pins Excessive wear Damaged rollers Improper chain adjustment Dry or rusted links Kinked or binding links If any defects are found the drive chain must be replaced NOTE When replacing the drive chain replace the drive chain and sprocket as a set Loose the axle nut Tense the drive chain fully by turning both chain adjusters PERIODIC MAINTENANCE 2 12 2 13 PERIODIC MAINTENANCE Count out 21 pins 20 pitches on the chain and mea sure the distance between the two points If the dis tance exceeds the service limit the chain must be replaced Service limit 319 4 mm Drive chain
15. tarter and record the maximum gauge reading as the compres sion of that cylinder Compression gauge 09915 64510 PERIODIC MAINTENANCE 2 20 2 21 PERIODIC MAINTENANCE OIL PRESSURE Check the oil pressure periodically This will give a good indication of the condition of the moving parts Standard Oil pressure 1 3 0 2 kg a at 60 C 4 000 rpm If the oil pressure is lower or higher than the specification the following causes may be considered LOW OIL PRESSURE Oil leakage from the oil passage Damaged O ring Defective oil pump Combination of above items HIGH OIL PRESSURE Engine oil viscosity is too high Clogged oil passage Combination of the above items OIL PRESSURE TEST PROCEDURE Check the oil pressure in the following manner Remove the oil check plug and install the adapter of oil pressure gauge at the removed position Connect an engine tachometer Warm up the engine as follows Summer 10 min at 2 000 rpm Winter 20 min at 2 000 rpm After warming up increase the engine speed to 4 000 rpm with the engine tachometer and read the oil pressure gauge Oil pressure gauge 09915 74510 Engine tachometer 09900 26006
16. the lower limit line LOWER on the front brake fluid reservoir When the level is below the lower limit line LOWER replenish with brake fluid that meets the following specification Specification and Classification DOT 3 or DOT 4 AA CAUTION The brake system of this motorcycle is filled with a glycol based brake fluid Do not use or mix dif ferent types of fluid such as silicone based or petroleum based Do not use any brake fluid taken from old used or unsealed containers Never re use brake fluid left over from the last servicing or stored for a long period CAUTION Brake fluid if it leaks will interfere with safe run ning and immediately discolor painted surfaces Check the brake hoses and hose joints for cracks and oil leakage before riding PERIODIC MAINTENANCE 2 14 AEN A e An N O OXO O N A NG KENI EGA NANA BINAN ARAN TN oyo oo 010 0f6 Of0 9 2 15 PERIODIC MAINTENANCE BRAKE PAD WEAR The extend of brake pad wear can be checked by observing the grooved limit on the pad When the wear exceeds the grooved limit replace the pads with new ones AA CAUTION Replace the brake pad as a set otherwise braking performance will be adversely affected FRONT BRAKE PAD REPLACEMENT Remove the brake caliper Remove tne brake pads To reassmble reverse the above sequence 8 Brake caliper mounting bolt 18 28 N m 1 8 2 8 kg m FRONT BRAKE FLUID REPLACEME
17. uality replacement parts can cause your motorcycle to wear more quickly and shorten its useful life Use only genuine Hyoung replacement parts or their equivalent PERIODIC MAINTENANCE 2 2 LUBRICATION POINT Proper lubrication is important for smooth operation and long life of each working part of the motorcycle Major lubrication points are indicated below 1 Clutch lever holder 2 Drive chain 3 Side stand pivot and spring hook 4 Brake lever holder 5 Brake pedal pivot fe Motor oil Il Grease NOTE Before lubricating each part clean off any rusty spots and wipe off any grease oil dirt or grime Lubricate exposed parts which are subject to rust with either motor oil or grease whenever the motorcycle has been operated under wet or rainy condition 2 3 PERIODIC MAINTENANCE MAINTENANCE PROCEDURE This section describes the service procedure for each section of the periodic maintenance VALVE CLEARANCE NOTE Inspect Initial 1 000 km and Every 4 000 km AA CAUTION The clearance specification is for COLD state The valve clearance specification is different for intake and exhause valves Valve clearance adjustment must be checked and adjusted 1 at the time of periodic inspection 2 when the valve mechanism is serviced and 3 when the camshaft is disturbed by removing it for servicing Remove the spark plug Refer to page 2 5 Remove the right air cleaner box Remove the fuel
Download Pdf Manuals
Related Search