IW709 USA Supplemetary Service Manual
Contents
1. 426520 not for any IW Smarttool may be used to extract more service information To download data use the Start Pause button from fault mode or diagnostic mode IW Models IW509 IW609 W709 IWECO Models IWC09 IWM10 IW710 IWL10 W810 E 2 Specifications for ITW Models Size Width Wash Load Capacity Compact 5 560mm IW509 IWC09 5 5kg Medium 6 600mm IW609 IWM10 IW710 6 5 7kg Large 7 650mm IW709 IWL10 IW810 7 5 8kg Water consumption per fill with clothes load Compact Medium Large High 65 litres 82 litres 90 litres Medium high 58 litres 65 litres 76 litres Medium 47 litres 52 litres 61 litres Medium low 33 litres 38 litres 47 litres Low 22 litres 25 litres 32 litres Recirculating Valve 1 5Kohms 20 C Only fitted to IWM10 IW710 IWL10 IW810 Pump Water Valves Stator Rotor RPS all as Phase 5 Smartdrive 80 E 3 INTRODUCTION to IW This Service Supplement contains specifications a size setting and diagnostic mode The first Intuitive Washer W was introduced in Phase 5 Smartdrive in 1999 Three models were released IW509 IW609 and IW709 These products were upgraded in 2000 to include recirculation these products are called Intuitive ECO These products were IWCO9 non recirc IWM10 W710 IWL10 and IW810 PERFORMANCE CHANGES The Eco Active wash with Recirculation Only IWM10 IW710 IWL10 IW810 The Eco Active wash of the Intuitive Eco is a 2 step wash process that combines top loader and f2. caused Other USER WARNINGS which may appear in the LCD are Out of balance Warning Status No hot water Out of Balance No cold water 3 cycles ago No water at progress SPIN Overloaded Too many suds Service information for user warnings is in Section 10 MACHINE STATUS The Machine Status screen displays the status of the lid switch and the out of balance switch It also displays the Size setting of Smartdrive and the water temperature measured by the thermistor The state of the Diverter may be changed in IWECO When the lid is opened the screen display will change from reading Machine Status closed to open Similarly for the out of balance switch test If DIVERTER Off hot water is passed through the water chamber the temperature read Size 650 OOB off out in the screen will change accordingly as measured by the T 22degC Lid closed thermistor On the IWM10 IW710 IWL10 IW810 the DIVERTER option will also appear When changing the diverter from OFF to ON the display will say HEATING for approximately 1 minute This is the length of time the diverter takes to change from the OFF state to the ON state When changing the diverter from ON to OFF the display will say COOLING for approximately 3 minutes A number adjacent to the diverter state gives an indication of the time to go maximum 180 85 FAULT STATUS The Fault Status screen will display the fault code for the current
3. Appendix E IW SMARTDRIVE SERVICING E 1 IW Quick Reference Guide The Intuitive Washer can display the most recent user warning and fault The Intuitive Washer uses the motor to detect the fabric type The Intuitive Washer uses the same motor bowl and wrapper as Phase 5 Smartdrive Two types Intuitive Washer IW without recirculation and Intuitive Eco WECO with recirculation The display clearly identifies this at power up IW ECO Hot water is only used during recirculation This results in greater energy efficiency IW ECO Due to the reduced amount of water used during recirculation extra care must be taken not to use too much detergent This could result in over sudsing IW ECO The time to turn the diverter valve on is 1 minute and 3 minutes to turn it off So there could be a delay before draining starts The button Specials in IW has been renamed LifeCycles in IWECO If LEDs are flashing Restart may be off or Recycle may be on These are not the default states Option Adjustment Mode Hold the Options button down for 4 seconds Diagnostic Mode Hold down the Specials LifeCycles button and press Power Use the Specials LifeCycles button and buttons on the right of the LCD to toggle product status Or use the Options button to turn restart amp recycle ON or OFF Size Setting Mode Hold down the Fabric Care button and press Power Display 426961 not for IVECO Motor Controller
4. OFF This will allow any fault in the system to show up immediately With RESTART ON If a fault occurs in Smartdrive the diagnostic system will detect it However instead of displaying a fault code immediately Smartdrive will retry several times If the fault was only of temporary nature Smartdrive will finish the cycle If there is a continuous fault Smartdrive will retry a number of times This process could take up to 8 minutes depending on the type of fault After this if Smartdrive still cannot restart the fault code is displayed and will beep continuously The status of RESTART is indicated during normal use of Smartdrive as follows If none of the 5 green HOW DIRTY LED s are on RESTART is on If the 5 green HOW DIRTY LED s are flashing RESTART is off NB RESTART is designed as a service aid only and should be left ON in the customer s home To return to normal operation and to reset RESTART to the default setting switch Smartdrive off at the wall If this does not reset the state then RESTART and RECYCLE must be reset in EEPROM To set these states hold down the button adjacent to the LCD for 2 seconds Smartdrive will beep once 86 RECYCLE In the Control Option mode similar to setting the RESTART Push the button beside the word RECYCLE to toggle on and off Recycle At the end of servicing Smartdrive may require an extended test where it can be left to complete a number of wash cycles By turning
5. efault Smartdrive will stop give a short burst of beeps every five seconds and display a message to let you know to redistribute the load more evenly Use this option to conserve water End of Cycle BEEPS The number of beeps at the end of the cycle can be set to zero five default or fifteen Use the DOWN and UP buttons to decrease or increase the number of beeps The LCD will display the number of beeps selected 84 E S DIAGNOSTIC MODE for IW DIAGNOSTIC MODE incorporates tests for the pump diverter valve water valves and also the data display mode To enter DIAGNOSTIC MODE turn the power on at the power point and off at the console Press and hold the SPECIALs LifeCycles button and then the POWER button Smartdrive will give 2 short beeps and the LCD screen will go blank NB Make sure that the buttons are released after the beeps or Smartdrive will take itself out of diagnostic mode STATUS DISPLAY To display the status push the SPECIALS LifeCycles button again This will display the status of the lid switch and the out of balance switch It will display the last fault and last User Warning One of 3 displays will appear in the LCD Use the buttons to the right of the LCD to toggle these display options WARNING STATUS The Warning Status screen will display the last USER WARNING which occurred It states how many cycles ago and the wash state This is a fault that the Customer may have
6. nd a digital valve on the hot Resistance 64 ohms STATOR amp ROTOR The stator amp rotor are the same as Phase 5 Stator resistance is 16 ohms per winding 32 ohms phase to phase RECIRCULATING VALVE Only fitted to IWM10 IW710 IWL10 IW810 The Recirculating valve is situated at the bottom of the bowl beside the pump If the valve requires service remove the hose clips connecting the hoses to the valve and remove the screwed clamp around the inlet hose to the valve The valve now can remove for cleaning or checking This is best achieved by working from underneath Smartdrive The valve relies on element heating to open The picture below shows the connector for the Recirculating valve in the motor controller module The valve can be tested in the DIAGNOSTIC mode within the Machine Status screen NB The valve takes approx 1 minute to activate and approx 3 minutes to cool down and return to it normal position It will make no sound during activation 82 RECIRCULATING VALVE The pump is the same as Phase 5 The pump forms part of the power supply If it not connected Smartdrive will appear to have no power The pump resistance is 33 ohms E 4 OPTION ADJUSTMENT MODE for IW In Option Adjustment Mode the following adjustments may be made The fill level selected by Auto Water Level The type of rinse The temperature of the wash The spin speed for Creasables The recovery routine selected when a load goes ou
7. on RECYCLE Smartdrive will continuously repeat the selected wash cycle until RECYCLE is turned off The status of RECYCLE is indicated during normal use when Smartdrive is first turned on If none of the FABRIC CARE LED s are on recycle is off If all of the FABRIC CARE LED s are flashing recycle is on NB Recycle is designed as a service aid only and should be OFF in the customer s home To return to normal operation and to return recycle to the default setting switch Smartdrive off at the wall If this does not reset the state then RESTART and RECYCLE must be reset in EEPROM To set these states hold down the button adjacent to the LCD for 2 seconds Smartdrive will beep once HOT BOWL FLAG If Smartdrive has been filled with hot water and has not had a cold rinse Smartdrive will not spin up to its full speed of 1000 RPM its maximum speed will be reduced to 700 RPM To remove this flag enter the Control Option mode and push the button beside the words HOT BOWL CLEAR or put Smartdrive through a complete final rinse NB The drain pump test water valve test restart recycle and hot bowl flag can be accessed from any level in the diagnostic mode E 6 SIZE SETTING MODE for IW It is important to set the size of Smartdrive into the Motor Controller s EEPROM whenever a replacement Motor Controller or Display Module is fitted to Smartdrive Failure to do so will result in fault code 9 To set the size turn the power on at the po
8. or Fault Status last fault that has occurred in Smartdrive It will also display how Fault code 130 many cycles ago the fault occurred and at what part of the cycle The 5 cycles ago fault code can be checked in Section 11 to identify the repairs that at progress SPIN may be necessary DRAIN PUMP TEST When in diagnostic mode the FABRIC CARE button turns the drain pump on or off This can be helpful if the bowl is still full of water The pump is run at 50Hz for this test When in the 50Hz mode the pump will not turn on and off every 10 seconds When running this test the state of the diverter valve should be known This is the best method for checking the recirculation system Always check that there is no water pumped to drain when the product is recirculating and vice versa WATER VALVE TEST When in diagnostic mode pressing the HOW DIRTY down button will turn the Cold Water Valve on Pressing the HOW DIRTY up button will turn the Hot Water Valve on The buttons must be held on to keep the valves on RESTART Control Options restart recycle When in diagnostic mode pressing the OPTION button will bring up the Control Option screen hot bowl clear Smartdrive defaults to RESTART ON This is indicated on the screen by the word RESTART highlighted To turn RESTART OFF push the button alongside the word This will remove the highlight from the word RESTART When Smartdrive is being serviced it is more convenient to turn RESTART
9. ront loader washing technologies Wash 1 DETERGENT ACTIVATING WASH Front loader type wash Smartdrive fills the bowl with just enough water at the selected wash temperature so that the clothes are 100 saturated Smartdrive stops filling and the water in the bowl is pumped up through the recirculating hose and back into the bowl onto the clothes with a fan like spray pattern As the water recirculates the bowl stirs pausing every 16 seconds Short top ups may occur as garments absorb water keeping the water level constant This recirculating wash action thoroughly dissolves and activates the detergent The concentrated solution of detergent and water rapidly targets stains and soils at the fibre level boosting soil removal and accelerating the wash process Wash 2 AGITATION WASH Top loader type wash After re circulating the sudsy water through the clothes for 2 to 5 minutes Smartdrive fills with just enough cold water to suspend the clothes in solution Smartdrive then senses the fabric type of the load and begins the agitation wash The are 2 load sensing methods to ensure the right wash action is used for the type and size of wash load LSD Load Sensing Detection is used to continually sense the load and automatically adjust the agitation profiles to suit the wash load If additional garments are added during the wash Smartdrive will adjust accordingly MCP Maximum Capacity Profile is selected immediately when fabric detection
10. selects heavy duty at high water level ELECTRONICS The electronics are similar to Smartdrive Phase 5 Electronic Modules are not inter changeable between models The different modules for the different models can be identified by their colour Phase 2 modules are blue Phase 3 modules are green Phase 4 modules are yellow and the latest Phase 5 and IW modules are grey IMPORTANT Motor Controller part no 426520 should not be used with IW It will appear to function correctly but will give fault code 105 at the start of Agitate Display Module 426961 should not be used on products with recirculation the product will appear to work satisfactorily but the 81 recirculation will not work It is important not to mix the different coloured modules as they are not compatible and Smartdrive will not work It will normally display a fault code and beep if the modules have been mismatched Delay start is 1 to 9 hours IW or 18 hours IWECO in increments of 1 hour WATER TEMPERATURE SENSING The thermistor for sensing the water temperature in Smartdrive is located in the inlet chamber and is available as a separate spare part part number 479164P Hot water is only used at the start of the cycle when Smartdrive is recirculating Some hot water may be used in the first fill if the inlet water temperature is low below 18 C WATER VALVES The water valves are the same as Phase 5 GW Smartdrive A proportional valve is fitted on the cold a
11. t of balance The number of beeps at the end of the cycle Adjust Options Menu auto water temp auto rinse other With Smartdrive powered on push the OPTIONS button and hold down for 4 seconds The Adjust Options Menu will be displayed Push the small button next to the option to be adjusted The display will change to the choices available for that option To set the option push the small button next to it The display screen will highlight the selection before returning to the main screen 83 AUTO WATER Auto Water Level Adjustment The water level that Smartdrive fills to on auto water level may be Auto Water Adj ust adjusted Select AUTO WATER Use the MORE or LESS buttons to decrease or increase the fill level NB If there is not enough water for the load check by pausing Smartdrive and pushing the clothes down to see how much spare water is at the bottom of the bowl Clothes often float and Smartdrive can sensethe water under the clothes cancel OK less 7S more TEMP Wash Water Temperature Adjustment The wash temperatures can be adjusted Select TEMP Use the DOWN or UP buttons to decrease or increase the wash temperature Select OK to save the new temperature settings Each move up or down is approximately 19C Water Temp Adjust cancel AUTO RINSE Rinse Default Options This menu changes the rinse option to which Smartdrive defaults Rinse Defaults Spray and deep is the s
12. tandard rinse default It may be desirable to change the type of rinse selected for a number of reasons If there is problem with impurities in the water supply a better wash may be attained by changing the rinse option to 2 deep rinses To conserve water select a single deep rinse or a shower rinse single spray amp deep double shower Single Short spin followed by 1 deep rinse Double 2 deep rinses Spray amp Deep Spray rinse followed by deep rinse Shower Shower rinse Shower rinse alternately showers the clothes with water and spins them to remove the sudsy water It is not designed to be used with fabric softener as a shower rinse does not use a deep rinse so it cannot dispense fabric softener correctly OTHER OPTIONS Other Defaults Creasable Spin Speed The Creasables fabric care option defaults to a slow spin speed 300rpm However a medium spin speed 700rpm may be selected Select OTHER Select CREASABLE SPIN Select MEDIUM Creasable Spin OOB Beeps OUT OF BALANCE Recovery While Smartdrive is spinning if it senses the wash load is out of balance it stops It retries spinning up to three times If an unbalanced load is detected there are two recovery options Automatic Recovery Option Smartdrive tries to automatically correct the out of balance load It fills with water and agitates to redistribute the load before trying to spin up again OOB on the LCD is highlighted Machine Stops Option d
13. wer point and off at the console Press and hold the FABRIC CARE button then press the POWER button This will give either of the following options in the LCD screen IW509 W609 W709 MACHINE SIZE SETUP size is determined in the conventional 5 7 way with sizes 5 6 amp 7 6 IWC09 IWM10 W710 MACHINE SIZE SETUP IWL10 W810 560 650 size is determined by product width in mm 600 no size The LCD screen has a number of options Pushing the button alongside the appropriate machine size or product width will select and highlight the size Pushing the POWER button will set the size into the module s memory 87
Download Pdf Manuals
Related Search