Home

Instructions

1. In a scenario where an auto negotiation device is linked to a non negotiating device the negotiating device via parallel detection recognizes the speed of that second device then establishes the best operating speed 10Mbs or 100Mbs at half duplex MDI or MDI X The EOF2N utilizes either straight through MDI or crossover MDI X copper cables when connecting to 10Base T or 100Base TX devices the EOF2N determines the characteristics of the connection and automatically configures the device to link up regardless of the copper cable configuration MDI or MDI X Link Pass Through The Link Pass Through feature illustrated below allows the media converter to monitor both the fiber and copper RX receive port for loss of signal In the event of an RX signal loss 1 the media converter will automatically disable the TX transmit signal 2 thus passing through the link loss 3 The far end device is automatically notified of the link loss 4 which prevents the loss of valuable data unknowingly transmitted over an invalid link media converter A media converter B disables the fiber TX link loses the fiber RX link Near End Media Media Far End Device Converter A Converter B_ 7 Device 1 0 original fault on the copper link media converter B disables the copper link Note In the link pass through devices EOF2N both copper and fiber cables must be installed before the LEDs will light Auto Negotiation AutoCross Link
2. PolEvators CamEvator Three 3 Years Warrior Series Q View Three 3 Years SView Series Three 3 Years 6 months if used in auto scan tour operation DeputyDome NiteTrac Igloo Dome PurgeDome Three 8 Years 6 months if used in auto scan tour operation EXO Series Dome and Fixed Camera Systems Three 3 Years 6 months if used in auto scan tour operation EXO Series GeminEye Visible and Thermal Camera Systems One 1 Year During the labor warranty period to repair the Product Purchaser will either return the defective product freight prepaid or deliver it to Manufacturer at Moog Decatur Operations 2525 Park Central Boulevard Decatur Georgia 30035 The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with a RMA Return Materials Authorization number displayed on the outer box or packing slip To obtain a RMA you must contact our Technical Support Team at 800 554 1124 extension 101 Manufacturer will return the repaired product freight prepaid to Purchaser Manufacturer is not obligated to provide Purchaser with a substitute unit during the warranty period or at any time After the applicable warranty period Purchaser must pay all labor and or parts charges The limited warranty stated in these product instructions is subject to all of the following terms and conditions TERMS AND CONDITIONS 1 NOTIFICATION OF CLAIMS WARRANTY
3. Pass Through Far End Fault Media Converter Auto Negotiation AutoCross LPT FEF EOF2N Yes Yes No Yes Product features Automatic link restoration The media converter will automatically re establish the link when connected to switches if the link is lost even with Auto Negotiation and Link Pass through both directions enabled Full Duplex flow control In a full duplex network the maximum cable lengths are determined by the type of cables used for EOF2N cable specifications The 512 Bit Rule does not apply in a full duplex network Note X Full duplex is ON permanently for the fiber port only Half Duplex flow control 512 Bit Rule In a half duplex network the maximum cable lengths are determined by the round trip dely limitations of each Fast Ethernet collision domain A collision domain is the longest path between any two terminal devices e g a terminal switch or router The 512 Bit Rule determines the maximum length of cable permitted by calculating the round trip delay in bit times BT of a particular collision domain If the result is less than or equal to 512 BT the path is good Flow Control The process of adjusting the flow of data from one device to another ensures that the receiving decive can handle all of the incoming data This is particularly important where the sending device is capable of transmitting data much faster than the receiving device can accept it Distance extension The EOF2N media converter
4. the unit Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety When the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachment accessories specified by the manufacturer Use only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lighting storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled of objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Be sure to periodically examine the unit and the supporting structure to make sur
5. 1000 J9UIS9AUOJ JOQI4 JOAO Jeuleul NZ4O3 S N Aquuessy 193x204 lOGdydOrda S N 48350 JUNOIN HOM BLITIOIEd 9 21014 Buyunow IBLZIAdI S JOD JOO 08974964 oF 824 UONISUUOI I08JADAPLAS E SUNJOJSUDI LLNVH IOZdH basco Buipniour Ajquuessy xog uow 00018d4DOHOFds 1511 SLHVd LNAWSDV 1438 uoyduosag J3QUINN HD y Ethernet Over Fiber Converter EOF2N Remove fiber converter from the power box Electrostatic Discharge ESD Always observe the following ESD precautions when installing or handing the EOF2N media converter e Do not remove the converter from its protective packaging until you are ready to install it e Wear an ESD wrist grounding strap before handling any module or component If you do not have a wrist strap maintain grounded connection with the system unit throughout any procedure requiring ESD protection CAUTION Integrated circuits and fiber optic components are extremely susceptible to electrostatic discharge damage Failure to observe this caution could result in damage to these components WARNING If the media converter is an IEEE802 3 2005 Powered Device PD capable of receiving power via the Media Dependent Interface MDI leads the power source connector and cables attached to the barrel power connector must meet the isolation requirement specified in IEEE802 3 2005 Copper and Fiber ports The illustration below shows the front panel of the EOF2N m
6. FOR THE FOREGOING WARRANTIES MANUFACTURER HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY AND OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2 312 3 OF THE UNIFORM COMMERCIAL CODE AND OR IN ANY OTHER COMPARABLE STATE STATUTE MANUFACTURER HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON MANUFACTURER PRODUCTS OR NON MANUFACTURER RECOMMENDED PRODUCTS PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT LIMITATION OF LIABILITY THE LIABILITY OF Manufacturer IF ANY AND PURCHASER S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE IN NO EVENT SHALL MANUFACTURER BE LIABLE TO PURCHASER FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION REPLACEMENT LABOR COSTS REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER Electric al Specifications English Espa ol Francais Deutsch Portuguese Italia no PB24FM SC Input Power 110 VAC 220VAC 1A 5A Power Consumpti
7. Installation and Operation Instructions NA D 06 e Before attempting to connect or operate this product please read these instructions completely PB24FM SC otandard Multi Functional Power Box with EOF2N Ethernet Over Fiber Converter PB24FM SC Rugged cast aluminium power box with 220 115Vac input converting to 24Vac and 96W output power Includes Ethernet over Fiber converter EOF2N Moog Inc sensor and Surveillance Systems O 2013 Moog Inc All Rights Reserved 3650 Woodhead Drive Northbrook IL USA 60062 81 IN5432 111913 1 847 498 0700 Fax 1 847 498 1258 www moogS3 com IMPORTANT SAFEGUARDS 4 NO TO SA CO nm 00 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with damp cloth Do not block any of the ventilation openings Install in accordance with the manufacturers instructions Cable Runs All cable runs must be within permissible distance Mounting This unit must be properly and securely mounted to a supporting structure capable of sustaining the weight of the unit Accordingly 10 11 12 13 14 15 16 a This installation should be made by a qualified service person and should conform to all local codes b Care should be exercised to select suitable hardware to install the unit taking into account both the composition of the mounting surface and the weight of
8. SERVICE If Purchaser believes that the Product is defective in material or workmanship then written notice with an explanation of the claim shall be given promptly by Purchaser to Manufacturer All claims for warranty service must be made within the warranty period If after investigation Manufacturer determines the reported problem was not covered by the warranty Purchaser shall pay Manufacturer for the cost of investigating the problem at its then prevailing per incident billable rate No repair or replacement of any Product or part thereof shall extend the warranty period of the entire Product The specific warranty on the repaired part only shall be in effect for a period of ninety 90 days following the repair or replacement of that part or the remaining period of the Product parts warranty whichever is greater 2 EXCLUSIVE REMEDY ACCEPTANCE Purchaser s exclusive remedy and Manufacturer s sole obligation is to supply or pay for all labor necessary to repair any Product found to be defective within the warranty period and to supply at no extra charge new or rebuilt replacements for defective parts 3 EXCEPTIONS TO LIMITED WARRANTY Manufacturer shall have no liability or obligation to Purchaser with respect to any Product requiring service during the warranty period which is subjected to any of the following abuse improper use negligence accident or acts of God i e hurricanes earthquakes modification failure of the end user to follo
9. aracteristics must meet or exceed IEEE 802 3 M specifications Fiber cable Bite Error Rate 10 9 single mode fiber recommended 9 um Multimode fiber recommended 62 5 125 um Multimode fiber optional 100 140 85 140 50 125 um EOF2N EOF2N 1300 nm multimode Fiber Optic Transmitter Power min 19 0dBm max 14 0 dBm Fiber Optic Receiver Sensitivity min 30 0 dBm max 14 0 dBm The fiber optic transmitters on this device meet Class Laser safety requirements per IEC 825 CDRH standards and comply with 21 CFR1040 10 and 21CFR1040 11 Copper cable Category 3 Minimum requirement for 10 Mb s operation Gauge 24 to 22 AWG Attenuation 11 5 dB 100m Q 5 10 MHz Maximum Cable Distance 100 meters Category 5 Minimum requirement for 100 Mb s operation Gauge 24 to 22 AWG Attenuation 22 0 dB 100m Q 100 MHz Maximum Cable Distance 100 meters e Straight through or crossover twisted pair cable may be used e Shielded STP or unshielded UTP twisted pair cable may be used e Pins 142 and 386 are the two active pairs in an Ethernet network e Use only dedicated wire pairs for the active pins e g blue white amp white blue orange white amp white orange etc e Do not use flat or silver satin wire Straight Through Crossover Cable Twisted Pair 1 Twisted Pair 1 Twisted Pair 2 Twisted Pair 2 lt O O 8 00 203 2 V ES 2 00
10. e that the integrity of the installation is intact Failure to comply with the foregoing could result in the unit separating from the support structure and falling with resultant damages or injury to anyone or anything struck by the falling unit UNPACKING Unpack carefully Electronic components can be damaged if improperly handled or dropped If an item appears to have been damaged in shipment replace it properly in its carton and notify the shipper Be sure to save 1 The shipping carton and packaging material They are the safest material in which to make future shipments of the equipment 2 These Installation and Operating Instructions SERVICE If technical support or service is needed contact us at the following number TECHNICAL SUPPORT AVAILABLE 24 HOURS 1 800 554 1124 SAFETY PRECAUTIONS 7 O CAUTION DO NOTOPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICE ABLE PARTS INSIDE REFER SEVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk to persons Este s mbolo se piensa para alertar al usuario a la presencia del voltaje peligroso no aislado dentro del recinto de los productos q
11. edia converters TX Link Act LED FX Link Act LED Copper Port Power ON LED Connect the fiber cable Full duplex always ON is on the fiber side only therefore the 512 Bit Rule does not apply The cable lengths are constrained by the cable requirement 1 Locate or build IEEE 803 2 M compliant 100Base FX fiber cable with male two stranded TX to RX connectors installed at both ends 2 Connect the fiber cable to the EOF2N media converters as follows e Connect the male TX cable connector to the female TX port e Connect the male RX cable connector to the female RX port 3 Connect the fiber cable to the other device another media converter hub etc as follows e Connect the male TX cable connector to the female RX port e Connect the male RX cable connector to the female TX port Connect the fiber cable to Connect the fiber cable the media converter to other device media a converter hub etc as shown shown pl i Connect the twisted pair copper cable The EOF2N allows either MDI straight through or MDI X crossover cable connections to be configured automatically according to network conditions e f half duplex mode is used refer to the 512 Bit Rule If full duplex mode is used the 512 Bit Rule does not apply The cable lengths are constrained by the cable requirements Locate or build IEEE 803 2 M compliant 10Base T or 100Base TX cables with RJ 45 connectors installed at both ends Connect
12. el n est pas inclus Die Wand die den Energie Kasten anbringf ist m glich aber die Kleinteile sind nicht enthalten A parede que monta a caixa do poder poss vel mas a ferragem n o inclu da La parete che monta la scatola di alimentazione e possibile ma i fissaggi non sono inclusi Wall Mount Gasket 3 8 Bolts Washer The wall mount brac ket must be attached using the gasket as shown El soporte del montaje de la pared se debe unir usando la junta segun lo demostrado La parenth se de b ti de mur doit tre jointe utilisant la garniture comme montr e Der Wandeinfassung Haltewinkel muB mit der Dich tung angebracht werden wie gezeigt worden O suporte da montagem da parede deve ser unido usando a gaxeta como mostrado La staffa del supporto della parete deve essere fissata per mezzo della guarnizione come indicata The powerbox may be pole mounted with the pole support clips sta es la plantilla del montaje para la caja de la energ a C est le calibre de support pour la boite de puissance Dieses ist die Montageschablone f r den Energie Kasten Este o molde da montagem para a caixa do poder Ci e la mascherina del montaggio per la scatola di alimentazione Conduit Fitting This is the assembled unit with the housing and conduit El soporte del montaje de la pared se debe unir usando la junta seg n lo demostrado La parenth se de b ti de mur doit tre jointe utilisant la ga
13. on Amp 120 Watts at 120 VAC Power Output 96 VA at 24 VAC 52 Watts Heater Blower 32 Watts Camera Power An all pole main switch with a contact of atleast 3mm in each pole shall be incorporated in the electrical installation of the building Tools Required 150 Flathead Screwdriver 7 16 Wrench or Socket 9 16 Wrench or Socket Energ a De Entrada 110 Consumo De Energ a de VAC 220VAC 1A 5A 1Amp 120 vatios en 120 VAC de salida de energ a VA 96 en 24 VAC 52 vatios de Heater Blower 32 vatios de energ a de la c mara fotogr fica Todo el interruptor principal del poste con un contacto de porlo menos 3m m en cada poste ser incorporado en la instalaci n el ctrica del edificio Herramienta s Requeridas destomilladorde cabeza llana del 150 7 16 llave de la llave o del z calo 9 16 o z calo Puissance D entr e 110 Puissance D nergie de VAC 220VAC 1A 5A 1Amp 120 watts 120 VCA de rendement de puissance VA 96 24 VCA 52 wattsde Heater Blower 32 watts de puissance d appareil photo Un tout le commutateur principal de poteau avec un contact au moins de 3mm dans chaque poteau sera incorpor dans l installation lectrique du b timent Outils Requis toumevis t te plate de 150 7 16 cl de cl ou de douille 9 16 ou douille Zugefuhrte Energie 110 VAC 220VAC 1A 5A Leistungsa ufna hme lAmp 120 Watt bei 120 VAC Abgabeleistung VA 96 bei 24 VAC 52 Watt Heater Blower 32 Watt Ka mera Energie Ein aller Pfos
14. rniture comme montr e Der Wandeinfassung Haltewinkel muB mit der Dichtung angebracht werden wie gezeigt worden O suporte da montagem da parede deve ser unido usando a gaxeta como mostrado La staffa del supporto della parete deve essere fissata per mezzo della guarnizione come indicata INPUT 120VAC or 240VAC 120Vac Input Input Main O Switch Line D and Neutral N wires should be connected as marked on the board and plugged into the conesponding voltage for the input single phase Los alambres de la l nea I y del hilo neutro n se deben conectarseg n lo marcados en el tablero y tapa dosen el voltaje correspondiente para la monof sico de la entrada Des fils de la ligne I et du neutre n devraient tre reli s comme marqu sur le conseil et branch a la tension correspondante pourle monophas d entr e Linie L und des Neutralen N Leitungen sollten angeschlossen werden wie auf dem Brett gekennzeichnet worden und in die entsprechende Spannung f rdas Eingang einphasige verstopft Osfiosda linha L e do ponto morto N devem serconectadoscomo marcadosna placa e plugged na tens o comespondente para a fase monof sica da entrada I legare della linea I e del neutrale n dovrebbero essere collegati come contrassegnato sul bordo ed inserito la tensione corrispondente perla monofase dell input SAIS ERNIA HEATERS CAMERA Connect EE Housing Power Optional 24Vac 24Vac Power Outp
15. s mbolo do ponto do exclamation pretendido alertar o usu rio presenca de instruc es importantes na literatura que acompanha o dispositivo Questo simbolo del punto del exclamaton inteso per avvertire l utente alla presenza delle istruzioni importanti nella letteratura che accompagna l apparecchio MADEN UE BUY AMERICA COMPLIANT e COUNTRY OF ORIGIN U S A Product Warranty Registration Register Your Products Online www moogS3 com technical support product registration Moog values your patronage We are solely committed to providing you with the highest quality products and superior customer service With 3 Year and 5 Year warranties depending on the product purchased we stand behind every product we sell See full warranty details at www moogS3 com technical support warranty plan Register your products today to receive the following benefits e Simple and Trouble Free RMA process e Product software updates e Special promotions e Eliminate the need to archive purchase documents such as receipts purchase orders etc Limited Warranty for Moog Products Moog Decatur Operations subsequently referred to as Manufacturer warrants these products to be free from defects in material or workmanship as follows PRODUCT CATEGORY PARTS LABOR All Enclosures and Electronics Five 5 Years Accessory Brackets Five 5 Years Controllers Three 3 Years Power Supplies IR Illuminators Three 3 Years Poles
16. s cam segment one 1 10Base T copper Ethernet and or 100Base TX copper Fast Ethernet and one 1 100Base FX fiber Fast Ethernet collision domain In a half duplex Ethernet or Fast Ethernet environment the EOF2N media converters extend network distances by segmenting collision domains so that the 512 Bit Rule applies separately to each collision domain In a full duplex Ethernet or Fast environment the EOF2N media converters extend network distances to the physical cable limitations imposed by the selected twisted pair copper fiber cables Rate conversion The EOF2N media converters allow connection of 10Mb s terminal devices on a 10Base T legacy Ethernet copper network to 100Mb s terminal devices on a 100Base TX Fast Ethernet copper network and or to 1 00Mb s terminal devices on a 100Base FX Fast Ethernet fiber network Far End Fault always ON When a fault occurs on an incoming fiber link 1 the media converter transmits a Far End Fault signal on the outgoing fiber link 2 In addition the Far End Fault signal also activates the Link Pass Through which in turn disables the link on the copper portion of the network 3 and 4 original fault on the fiber link Far End Media Device Converter B Near End Device Media Converter A media converter A ULL di B signal is sent media converter disables the copper link disables the copper link p gt OON Cable Specifications The physical ch
17. tenhauptschalter mit einem Kontakt von 3mm mindestens in jedem Pfosten wird in der elektrischen Installation des Gebaudes enthalten Werkzeuge Erforderten 150 Flachkopfsc hraubenzieher 7 16 Sc hlussel oder Einfa sung 9 16 Schlussel oder Einfa sung Poder De Entrada 110 Consumo De Pot ncia de VAC 220VAC 1A 5A 1Amp 120 watts em 120 VAC de saida de poder VA 96 em 24VAC 52 watts de Heater Blower 32 watts de poderda c mera Todo o intemuptor principal do p lo com um contato ao menos de 3mm em cada p lo ser incorporado na instalac o el trica do edificio As Femra mentas Requerera m chave de fenda flathead do 150 7 16 de chave da chave ou do soquete 9 16 ou soquete Alimentazione in ingresso Di Entrata 110 Assorbimento di corrente Di energia di VAC 220VAC 1A 5A 1Amp 120 watt a 120 VCA di uscita di alimentazione VA 96 a 24 VCA 52 watt di Heater Blower 32 watt di alimentazione della macchina fotografica Tutto l intemuttore principale del palo con un contatto almeno di 3mm in ogni palo sara compreso nell installazione elettrica della costruzione Attrezzi Richiesti cacciavite a testa piatta del 150 7 16 di chiave dallo zoccolo o dalla chiave 9 16 o zoccolo Contents of Box Wall Mounting Attach unit securely with 4 3 8 or 8mm hardware not supplied La pared que monta la caja de la energ a es posible pero el hardware no es incluido Le mur montant la boite de puissance est possible mais le mat ri
18. the RJ 45 connector at one end of the cable to the RJ 45 port on the EOF2N media converter Connect the RJ 45 connector at the other end of the cable to the RJ 45 port on the other device switch workstation etc RJ 45 port RJ 45 port on the media on the other device converter Switch work station etc Status LEDs Use the LEDs to monitor the status of the media converter LED discriptions are as follows TX Link Act LED FX Link Act LED Green ON Link fiber FX Link Act LED Flashing Activity TX Link Act LED Green ON Link Flashing Activity Power LED Power ON LED Green ON Connected to power Front Panel Product features Congestion reduction The EOF2N media converter do not forward collision signals or error packets from one collision domain to another resulting in improvements in baseline network performance In addition the media converter filters packets destined for local devices which reduces network congestion also Auto Negotiation The Auto Negotiation feature is ON permanently for the EOF2N media converters Auto Negotiation allows the media converter to configure itself automatically to achieve the best possible mode of operation over a link It broadcasts speed 10 Mb s or 100 Mb s and duplex capabilities full or half to the other device and negotiates the best mode of operation Auto Negotiation allows quick and easy installation because the optimal link is established automatically
19. ue puede ser un riesgo de choque el ctrico Ce symbole est pr vu pour alerter l utilisateur la presence de la tension dangereuse non isol e dans la cl ture de produits qui peut tre un risque de choc lectrique Dieses Symbol soll den Benutzer zum Vorhandensein der nicht Isolier Gefahrdungsspannung innerhalb der ProdukteinschlieBung alarmieren die eine Gefahr des elektrischen Schlages sein kann Este s mbolo pretendido alertar o usu rio presenca di tens o perigosa non isolada dentro do cerco dos produtos que pode ser um risco de choque el trico Questo simbolo inteso per avvertire l utente alla presenza di tensione pericolosa non isolata all interno della recinzione dei prodotti che pu essere un rischio di scossa elettrica The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Este s mbolo del punto del exclamation se piensa para alertar al usuario a la presencia de instrucciones importantes en la literatura que acompa a la aplicaci n Ce symbole de point d exclamation est pr vu pour alerter l utilisateur la presence des instructions importantes dans la litt rature accompagnant l appareil Dieses Ausruf Punktsymbol soll den Benutzer zum Vorhandensein de wichtigen Anweisungen in der Literatur alarmieren die das Ger t begleitet Este
20. ut To Housing A O witch Internal resettable fuses are supplied for the main 24VAC output lines Do not connect heaters to camera output The 30334 is not designed for 3 phase or 208V systems Los fusibles resta ura bles intemos se proveen para lasl neasde salida principales 24VAC No conecte los calentadorescon la salida de la c mara fotogr fica El 30334 no se dise a para 3 fases o sistemas 208V Des fusibles r glables inte mes sont foumis pour les lignes de la sortie 24VAC principales Ne reliez pas les r c ha uffeurs au rendement d appareil photo Le 30334 n est pasconcu pour 3 phases ou syst mes 208V Inteme r ckstellba re Sicherungen werden f r die Haupt 24VAC Ertragskurven geliefert Schlie en Sie Heizungen nicht an Kameraausgang an Das 30334 ist nicht f r 3 Phase oder Systeme 208V bestimmt Os fusiveis resettable intemos s o fomecidos para aslinhasde sa da 24VAC principais Nao conecte calefatoresa sa da da camera O 30334 n o projetado para 3 fases ou sistemas 208V fusibili resetta ble intemi sono fomiti perle linee di uscita principali 24VAC Non colleghi i riscaldatori all usc ita della macchina fotografica Il 30334 non progettato per 3 fase o sistemi 208V INM OVA OZI ZH 09 05 DVAOvC OCC IVAOZI Buum J9uJJ0JSUDJ RP76PCBPBO1 RP96GK2680 JU MAIA Zu09 0S AS LI TERISI x008 DEJO GE 1D OVAFC ju M uig TEENS z 409 0S AG UMOJg RP7OTRAN11 RPVL2781 RP40HGPB
21. w the directions outlined in the product instructions failure of the end user to follow the maintenance procedures recommended by the International Security Industry Organization written in product instructions or recommended in the service manual for the Product Furthermore Manufacturer shall have no liability where a schedule is specified for regular replacement or maintenance or cleaning of certain parts based on usage and the end user has failed to follow such schedule attempted repair by non qualified personnel operation of the Product outside of the published environmental and electrical parameters or if such Product s original identification trademark serial number markings have been defaced altered or removed Manufacturer excludes from warranty coverage Products sold AS IS and or WITH ALL FAULTS and excludes used Products which have not been sold by Manufacturer to the Purchaser All software and accompanying documentation furnished with or as part of the Product is furnished AS IS i e without any warranty of any kind except where expressly provided otherwise in any documentation or license agreement furnished with the Product ANY COST ASSOCIATED WITH REMOVAL OF DEFECTIVE PRODUCT AND INSTALLATION OF REPLACEMENT PRODUCT IS NOT INCLUDED IN THIS WARRANTY 4 PROOF OF PURCHASE The Purchaser s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility DISCLAIMER OF WARRANTY EXCEPT

Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents