Assembly and User Manual
Contents
1. DK P821 ND DK 478 1831 ND DK 478 1831 ND DK 478 1831 ND DK 478 1831 ND DK 478 1831 ND DK 1N4148T 73CT ND DK LM1881N ND DK CF1 4680K5 RCT ND DK CF1 410K5 RCT ND DK CF1 4100K5 RCT ND DK CF1 4470K5 RCT ND MR 531 PT10MH 250K DK CF1 4100K5 RCT ND DK CF1 44 7K5 RCT ND DK CF1 44 7K5 RCT ND DK CF1 447K5 RCT ND DK 2N3906GOS ND DK 2N3904GOS ND Suggested Part Number DK A24807 ND DK A24807 ND DK AE9989 ND DK EG1957 ND See notes on Page 10 9 30 2008 Fuse holder Primary circuit 10 Power cord Primary circuit 10 DK Q114 ND Power switch Primary circuit 10 USB RS232 board RS232 level shifter 15 SF BOB 00198 RS232 to TTL board RS232 level shifter 15 NKC KIT 0004 AVR Notes The ATMEGA168 20 AVR must be programmed in order for the Clock mode to work and is only available with a small Clock parts kit from Dutchtronix www dutchtronix com In case of future software upgrades that are made available on the Dutchtronix website more information on programming the AVR can be found on Page 15 The firmware for the AVR incorporates long term time correction using mains frequency which is a feature not available on the original Dutchtronix scope clocks so all the firmware for the original clocks are incompatible Transformer Notes The PCB was designed to operate off a wide variety of common power transformers similar to the Hammond 270X The requirements for the secondaries are as follows 1 32. It utilizes the same sweep generator used for the oscilloscope in addition to another sweep generator for the vertical deflection to create a raster scanning pattern on the screen The circuitry is quite simple so the picture is visible but not fantastic These are all the features available with a fully populated PCB but the board could be partially built for fewer features such as a standalone scope clock The PCB was designed to run solely off a transformer for isolation purposes to provide some additional safety More importantly the PCB contains high voltage circuitry where the largest potential difference is at around 1000 volts so extra care should be taken when building handling and operating the board All the details on assembly and parts are included in this manual This manual is written under the assumption that the reader has some experience with soldering and mounting components CRT Clock TV Scope Page 3 9 30 2008 PARTS LIST The PCB and a small Clock parts kit are only supplied components of the CRT Clock TV Scope kit All the other parts will have to be obtained at the discretion of the builder The parts list is separated in five sections essentials clock scope TV and miscellaneous The essentials are the parts required for the PCB to do anything useful that is a basic XYZ scope display The Clock Oscilloscope and TV parts may be added to extend the capability of the PCB to include that feature Due to the integrat
3. keep in mind while mounting and soldering components in place e Ensure that the diodes are installed in the correct direction indicated on the PCB 1N4004 and 1N4007 diodes have a gray white band that indicates the cathode end of the diode so check that the band matches the white band on the diode outline on the PCB This also applies to other diodes e Take great care to ensure that all the electrolytic capacitors especially the high voltage ones are installed in the correct polarity Ceramic capacitors may be installed in either direction e Whether the builder prefers to use IC sockets or soldering the IC in place ensure that the notch or recessed area on the IC package matches the notch in the outline of the IC on the PCB IC sockets are strongly recommended for the AVR microcontroller so it is easily removable for future software upgrades The PCB does not offer on board programming e When installing the battery the positive terminal is inserted in the hole nearest D10 and the negative terminal in the hole nearest Q6 Bend the unused tabs on the battery to prevent any risk of shorting e Jumper pins may be replaced with a rotary mode selector switch if preferred Details are in the User Manual under Mode Selection at Page 16 Transformer Wiring Once the PCB is completed the next step is to wire the transformer to the PCB and the CRT The high voltage winding of the transformer feeds into the 240A and 240B solder pads and the center
4. 30 2008 R19 R20 R23 R28 and T6 create a roughly variable current source that will charge up one of C2 to C7 for a linear sawtooth output The 556 timer discharges the capacitor so a new cycle can begin The range of capacitances C2 to C7 sets the frequency range from fast to slow C2 is the smallest value that pushes the 556 at the maximum possible operating frequency of about 500KHz Larger capacitors may be used beyond the value of C7 for a very slow horizontal frequency that may be desired if a long persistence CRT was used There are certainly better and faster circuits but the timer is a classic circuit The other half of the 556 is unused in Oscilloscope mode but used in TV mode The signal is simply fed into the vertical amplifier while the horizontal amplifier is connected to the output of the 556 sweep generator R28 HSYNC serves as a Fine Frequency control to change the frequency within a small range TV The TV mode is really a simple video monitor that is a step above an oscilloscope Another sweep generator running at around 60Hz feeds the vertical amplifier When the horizontal sweep is set at the maximum frequency range using C2 a raster scanning pattern is achieved R24 R29 R25 R27 and T7 are equivalent in function to R19 R20 R23 R28 and T6 respectively to create a variable current source C8 was selected so the operating frequency was around 60Hz The feedback resistor R26 allows the other half of the 556 to operat
5. 478 1831 ND DK P5174 ND DK ECA 1CM100B ND DK P5137 ND DK 478 1831 ND DK 1N4148T 73CT ND DK LM556CNFS ND 9 30 2008 R19 R20 R21 R23 R28 T6 10K 1 4W 100K 1 4W 470K 1 4W 100K 1 4W 250K 2N3906 1 pole 6 position switch resistor resistor resistor resistor HSYNC potentiometer PNP transistor DK CF1 410K5 RCT ND DK CF1 4100K5 RCT ND DK CF1 4470K5 RCT ND DK CF1 4100K5 RCT ND MR 531 PT10MH 250K DK 2N3906GOS ND See Oscilloscope Mode Setup and Usage on Page 14 all parts under Oscilloscope except for those with an are required for this feature TV Part Value C8 0 22uF C10 0 luF Cll 0 luF C12 0 luF C13 0 luF C14 0 luF D1 1N4148 IC3 LM1881 R22 680K 1 4W R24 10K 1 4W R25 100K 1 4W R26 470K 1 4W R27 250K R29 100K 1 4W R30 4 7K 1 4W R31 4 7K 1 4W R32 47K 1 4W T7 2N3906 T8 2N3904 Miscellaneous Part DIP 8 socket DIP 8 socket DIP 14 socket 4pole 3pos rotary switch Slow blow fuse CRT Clock TV Scope Description radial electrolytic ceramic disc ceramic disc ceramic disc ceramic disc ceramic disc signal diode sync separator resistor resistor resistor resistor VSYNC potentiometer resistor resistor resistor resistor PNP transistor NPN transistor Notes For TL082 For LM1881 For 556 Primary circuit Primary circuit Page 7 Package 8 4 1 5 5 5 5 5 DIP 8 TO 92 TO 92 Page 10 10 10 10 Suggested Part Number
6. 50VCT to 550VCT at 0 04A 2 6V at0 6A 3 5V at 0 6A The secondary current ratings listed above are minimum values for proper operation Transformers with higher current capabilities on any one of the three secondaries will work as long as the voltage is close to the required specifications The primary winding may be chosen to suit the AC mains supply of choice for instance 120V AC for the USA The 350VCT secondary is sufficient for the PCB to operate most 2 and 3 CRTs but likely too low for any 5 CRTs A S550VCT secondary is a bit high for 2 CRTs but works nicely for 3 and some 5 CRTs CRT Notes Below is a non exhaustive list of CRTs that have been tested on the PCB Some CRTs require an extra connection from the B on the PCB to the anode cap which is detailed in the assembly instructions on Page 12 Most American CRTs use a straightforward numbering system in which the first digit is the screen size and the number after P is the phosphor type To list a few common phosphors P1 is the generic green phosphor P4 is white and P7 is long persistence typically used for radar The long persistence phosphor can create interesting afterglow effects that may be desirable Refer to Appendix A on Page 26 for more information on phosphor types Most of the round electrostatic oscilloscope CRTs are difficult to find but are often found new old stock NOS from various tube suppliers or ebay The PCB is not designed for magnetically
7. CPU IC7 AD7302 DAC IC8 PCF8563 RT clock calendar IC6 socket For ATMEGA168 20 IC7 socket For AD7302 IC8 socket For PCF8563 Q6 32 768MHz clock crystal Q7 20MHz crystal R37 10K 1 4W resistor R38 10K 1 4W resistor R39 10K 1 4W resistor R40 4 7K 1 4W resistor R41 1K 1 4W resistor R42 10K 1 4W resistor R43 1K 1 4W resistor R44 330Q 1 4W resistor R45 10K 1 4W resistor S1 tactile switch T1 2N3904 NPN transistor Oscilloscope Part Value Description C2 0 001uF ceramic disc C3 0 01uF ceramic disc C4 0 1uF ceramic disc C5 luF radial electrolytic C6 10uF radial electrolytic C7 47uF radial electrolytic C9 0 1uF ceramic disc D2 1N4148 signal diode IC2 556 dual timer CRT Clock TV Scope Page 6 Pann DIP 28 DIP 20 DIP 8 See Page 8 DIP 28 DIP 20 DIP 8 TO 92 Package o0 00 wo Li AAA DIP 14 MR 140 50N2 220J RC MR 140 50N2 220J RC DK 478 183 1 ND DK ECA 1CM100B ND DK 497 2495 1 ND DK 497 2495 1 ND DK 1N4148T 73CT ND DK 1N4148T 73CT ND MR 556 ATMEGA168 20PU DK AD7302BNZ ND DK PCF8563PN MR 571 3902619 MR 571 3902616 MR 649 DILB8P 223TLF DK XC967 ND DK CTX062 ND DK CF1 410K5 RCT ND DK CF1 410K5 RCT ND DK CF1 410K5 RCT ND DK CF1 44 7K5 RCT ND DK CF1 41K5 RCT ND DK CF1 410K5 RCT ND DK CF1 41K5 RCT ND DK CF1 43305 RCT ND DK CF1 410K5 RCT ND MR 688 SKHHBW DK 2N3904GOS ND Suggested Part Number DK P4060A ND DK P4300A ND DK
8. CRT Clock TV Scope Assembly and User Manual Jon B Stanley Electronixandmore com CRT Clock TV Scope Page 1 9 30 2008 TABLE OF CONTENTS INTRODUCTION ciscatandacaneinteutabcass E s ntialS asinen a ETA A AT Oscilloscope T E AE EEOAE A AT A N stein sisie s Miscellaneous wiiercsascresnscrtcd tence cera tendeetvexetees AVR INOUGS eenn ieiet ER toes Transformer Notes ceseceesseceeeeeeeseeeeenees CRENOES 0 eenen ereta i E E Populating the PCB essessesessserssereesseerse Transformer WIrINg c ccceeeseceeeeeeeeeeneees CRT Socket and Wiring eeeeseeeeeessereseeee Final Assembly Steps Powering Up for the First Time 0 Oscilloscope Mode Setup and Usage Programming the AVR Microcontroller for Mode Selection viarte neaceedecarasondovenpanarmoreoemnreans Signal Input Limitations and Workarounds Frequency Range Switch Wiring TV Mode and No Oscilloscope Mode THEORY OF OPERATION Power Supply cigs eect sees Deflection Amplifiers XYZ Scope CIOCR cnt cics ten date T V NETE EE E O E E E AEO ES TROUBLESHOOTING seeeeeeeererereererreren APPENDIX A STANDARD REGISTERED P
9. G VOLTAGES CAUTION Operating voltages on the PCB are potentially lethal Take great care when making voltage measurements of any kind with power applied to the PCB Always turn off the power before handling the PCB or turning it upside down for voltage measurements Due to the wide range of power transformers that is compatible with the PCB the high voltage measurements may vary so lists of voltages are provided for three different transformer secondaries of 350VCT 450VCT and 550VCT that feeds into 240A CT and 240B The voltages below are rough approximations and the actual measured voltages may vary but should be reasonably close and follow the pattern of voltages For instance K will always read a voltage that is more negative than Al Use a DC meter capable of measuring up to 800VDC and connect the ground probe to GND on the PCB near the lower right Take great care when measuring voltages Use a well insulated probe and do not make voltage measurements with both hands Use only one hand to hold the probe and the other hand should be away from anything conductive If anything has to be powered off put down the probe and use that same hand to turn off the power Always power off the PCB and let it sit for a few minutes before handling Expected Voltages Solder Pad 350VCT 450VCT SSOVCT Gl 490 630 770 K 470 610 740 Al 350 470 570 A2 120 150 180 HV 245 315 385 CRT Clock TV Scope Page 28 9 30 2008 APPENDIX D SC
10. HEMATIC dii SERIAL PCOADCo PCIADCI 2 PCXADC2 PC ADCs PCs ADC4 SDA PCSADCS SCL PBEXTALITOSC1 PDO FXD PB7XTAL TOSC2 PD1 TXD PD INTO PDXINT 1 vce PD4XCKTO ACC PDs T1 AREF PDs6 AINo PD7 AIN1 GND PBO ICP AGND PB1 OC1A PB2 SS OC1B PBxMOSVOC2 E PB4 MISO PBS SCK CRT Clock TV Scope Page 29 9 30 2008 CRT Clock TV Scope VERTLINE HORZLINE 9 30 2008
11. HOSPHORS APPENDIX B CRT BASING DIAGRAMS eee APPENDIX C PCB OPERATING VOLTAGES iieeiseseeen APPENDIX D SCHEMATIC ssseeseesssesssssssessrsserssersserssees CRT Clock TV Scope Page 2 9 30 2008 ooo uuna BA WD INTRODUCTION The CRT Clock TV Scope is the result of efforts to develop a reasonably simple circuit that incorporates a few common and fun uses of an electrostatic CRT The PCB was mainly designed to drive a 2 inch to 3 inch oscilloscope CRT but some 5 inch CRTs will work Short descriptions of the available features are as follows e The XYZ Scope mode allows direct access to the deflection amplifiers for DC coupled XYZ inputs Applications include stereo audio monitoring Lissajous figures or another external scope clock e The Clock mode consists of the minimal hardware version of the Dutchtronix Scope Clock firmware V3 0 it provides all the CRT on screen features but lacks the LED and RS232 level converter e The Oscilloscope mode uses a simple sweep generator with a range up to a few hundred kilohertz The oscilloscope is good for simple waveform monitoring and experiments Basic triggering is an included feature of the oscilloscope e The TV mode will display a basic picture on the CRT screen with a composite video input This mode is not a full television receiver that decodes over the air VHF or digital signals
12. SOOKHz because the 556 timer sweep circuit tops out at this speed Higher frequencies will appear as a thick line A 1Meg attenuation potentiometer is recommended to attenuate the input signal to a suitable range for the op amp and behaves very much like the SIZE potentiometer A schematic for the input attenuator is shown below Input Signal 1Meg To Jumper Pad GND The op amp circuit is currently set up with a variable gain range from 1 to 11 with reasonably good response on its high impedance non inverting input but the input is limited to 5V or clipping and possible circuit damage will result An attenuation potentiometer provides the advantage of a variable voltage divider to reduce input signals with voltages above 5V to a level suitable for the input of the op amp including a range of gains below 1 The ground side of the potentiometer connects to the GND solder pad at the lower right of the PCB near transistor T6 If one wishes to simplify the size controls on the PCB for easier adjustment in Oscilloscope mode at the cost of picture quality for Clock mode then attenuation potentiometers may be used as the new size controls and a 10K to 100K resistor may be used in place of the XSIZE and YSIZE trimmer resistors R14 and R16 respectively on the PCB to give the op amp a fixed but sufficient gain The resistor is soldered in place of the two mount holes nearest the edge of the PCB As an example the section of the PCB where YSIZE is
13. ck the 6A and 6B connections on the PCB from the transformer Use an AC meter with probes on 6A and 6B to check for voltage Expected voltage should be around 6 to 8 volts AC e 78L05 IC4 may be damaged e Check that C20 and C21 are installed in the correct polarity If not replace the capacitor The 78L05 may also be damaged as a result of this so replacement is strongly recommended 5V reads as 0 on the DC meter e Check the 6A and 6B connections on the PCB from the transformer Use an AC meter with probes on 6A and 6B to check for voltage Expected voltage should be around 6 to 8 volts AC e 79L05 IC5 may be damaged e Check that C19 and C22 are installed in the correct polarity If not replace the capacitor The 79L05 may also be damaged as a result of this so replacement is strongly recommended The CRT image jitters or swims e The CRT is too close to the power transformer Some transformers have poor magnetic shielding while others such as the Hammond 270X has fairly good shielding e The best location for the transformer is behind the CRT base to prevent interference CRT Clock TV Scope Page 25 9 30 2008 APPENDIX A STANDARD REGISTERED PHOSPHORS E L A EMISSION COLOR i PHOSPHOR PERSISTENCE FLUORESCENCE PHOSPHORESCENCE Yellowish green Yellowish green Medium Used in cathode ray oscillograph and radar Yellowish green Yellowish green Medium Used in cathode ray oscillographs Yellowish oran
14. dding a jumper Then proceed to add the shunts on the jumpers for this mode using Mode Selection on Page 16 for instructions If a rotary mode selection switch was used then rotate the switch to TV mode The composite video input is fed into the PCB through the VIN solder pad Use the GND solder pad to connect to the ground shield of the video connector The PCB was not designed for a PCB mounted RCA jack so a loose video connector or cable will have to be used Composite video may be obtained from a video camera a DVD player a VCR that is either playing a tape or tuned to a TV station or the new DTV converter boxes Feed a composite video signal into VIN then apply power to the PCB A raster scanning pattern should appear on the screen as the CRT warms up Depending on the deflection settings the picture may be blown up Adjust XSIZE and YSIZE until the raster is roughly the shape of a square and adjust XPOS and YPOS until the raster reasonably fits in the CRT screen area The raster may show evidence of flickering Adjust VSYNC vertical sync until the flickering stops See if overshooting the VSYNC will cause the raster to flicker differently Too much adjustment in one direction may cause the vertical to collapse and stop oscillation so adjust it back where a raster is present with no flickering which is where the vertical is stable If no picture is visible then adjust HSYNC horizontal sync until a picture appears Chances are the pict
15. deflected CRTs CRT Clock TV Scope Page 8 9 30 2008 2AP1 3AP1 3BP1 3JP1 3JP7 3RP1 SBP1 SUP1 902A 913 CRT Clock TV Scope Size 2 round 3 round 3 round 3 round 3 round 3 round 5 round 5 round 2 round 1 round Works Color Yes Green No Green Yes Green Yes Green Yes Blue yellow afterglow Yes Green Yes Green Yes Green No Green No Green Page 9 Notes Bright and sharp Requires extensive modification to PCB Bright Bright anode cap connects to B Long persistence phosphor version of 3JP1 Bright Dim picture won t work for TV mode Dim picture won t work for TV mode Requires extensive modification to PCB Requires extensive modification to PCB 9 30 2008 ASSEMBLY Populating the PCB Once all the parts are gathered the first step in assembly is to populate the PCB with all the parts listed under Essentials and other categories if more features are desired All the components under Miscellaneous with the exception of IC sockets are not used on the PCB so ignore them It is easier to mount a few smaller components at a time while soldering them in place The idea is to have smaller components mounted first so when the board is upside down the surface of the table or workbench will keep the components pressed against the board Gradually advance from smaller to larger components until the board is fully populated with all the necessary components A few things to
16. e as their respective horizontal deflection counterparts in the horizontal deflection circuit and R13 sets the positioning for the vertical CRT Clock TV Scope Page 20 9 30 2008 IC1 is a TLO82 dual op amp used in a non inverting amplifier circuit because of the benefit of high impedances input for XYZ Scope and Oscilloscope modes R10 and R14 sets up the gain of the horizontal amplifier and the gain is determined by 1 R14 R10 R12 and R16 does the same respective function but for the vertical amplifier The variable gain controls the output amplitude and thereby the deflection range Clock IC6 is the ATMEGA168 microcontroller running the Dutchtronix Scope Clock code IC7 is an AD7302 digital to analog converter DAC that converts parallel digital outputs from IC6 to analog voltage levels for rapidly drawing a picture in XY mode IC9 is a Real Time Clock and Calendar RTC chip that stores all the time keeping and calendar information The microcontroller communicates to the RTC through serial communications T1 R40 and R41 create an inverting amplifier for the intensity signal from the microcontroller to drive the Z axis of the Scope R43 and R44 is a voltage divider that provides a voltage reference that determines a suitable output voltage range produced by the AD7302 that works well with the XYZ Scope D9 and D10 allow either the 5V or the battery to maintain power to the RTC so time and date settings are not lost when power is r
17. e in astable mode The LM1881 is a nice little sync separator chip that outputs vertical sync pulses on pin 3 and horizontal composite sync pulses on pin 1 The vertical sync is hardwired to the 60Hz sweep portion of the 556 via coupling capacitor C12 for triggering The horizontal sync connects to the same sweep generator used in Oscilloscope mode but the trigger selector TSEL connects HSYNC to TRIG signals for TV mode R27 and R28 are fine frequency controls labeled VSYNC and HSYNC respectively The controls are used to both calibrate and fine tune the sweep frequency to the sync signals C13 C14 R30 R31 R32 and T8 create a simple video inverter that worked best for the particular Z axis circuit in the XYZ Scope This is an area for future improvement CRT Clock TV Scope Page 22 9 30 2008 TROUBLESHOOTING This page is intended to be used as a guide with some possible solutions for potential problems that may be encountered during power up or afterwards Also reading the Theory of Operation starting on Page 20 will provide better understanding of component functions and aid in isolating and repairing problems CRT filament does not light Incorrect or bad filament connection Use a meter to check if 5VAC is present on the filament pins If so then CRT filament may be open Power off and double check by disconnecting filament pins and using an ohmmeter to check continuity Fuse in primary circuit is blown Try a higher rated fuse a
18. e line size If desired attenuation potentiometers may be added to the inputs to allow a wider range of input voltages that are not limited by the 5V supply of the op amp Refer to Signal Input Limitations and Workarounds on Page 18 for more information The final few steps depend on what features were added to the PCB and are described next CRT Clock TV Scope Page 13 9 30 2008 Clock Mode Setup and Usage If the Clock feature was added then power off and proceed to add the jumper shunts for this mode using Mode Selection on Page 16 for instructions If a rotary mode selection switch was used then rotate the switch to Clock mode Apply power again A clock face should appear on the screen after the CRT warms up If the picture appears backwards then power off and flip the wires leading to X1 and X2 then power on Similarly if the picture appears upside down then power off and flip the wires leading to Y1 and Y2 then power on Adjust XPOS and YPOS until the clock display appears roughly centered on the screen then adjust XSIZE and YSIZE until the clock fits the CRT face with about 0 25 inches of border from the edge of the CRT face Adjust ASTIG until the whole picture appears relatively sharp everywhere FOCUS and INTEN may need minor readjustment until the picture looks clean Depending on the CRT there may be some small visible blurs or retrace lines which is normal due to the simplicity of the deflection circuitry and the internal ca
19. emoved from the PCB R37 R38 R39 and R42 serve as pull up resistors to ensure a clean logic 1 C23 C24 C27 and C28 are all bypass capacitors placed close to the AVR and RTC to filter out noise that may cause erratic operation C25 and C26 are used to regulate the crystal frequency accuracy for the AVR Q6 and Q7 are crystals for the RTC and AVR respectively The hardware is nothing compared to the software used on the AVR to deal with input settings graphics and time keeping Refer to www dutchtronix com for more information Oscilloscope A basic oscilloscope is just one step above a XY Scope Rather than two inputs for both axes one axis is fed with a sawtooth signal that indefinitely moves the beam continuously left to right or backwards over time then repeats This allows the screen to display an input signal with respect to time IC2 is a 556 dual timer two 555 timers in one with only one half used in Oscilloscope Mode The timer is set up to run in astable free running mode due to the feedback resistor R21 and triggering is achieved by C9 When the amplitude of the signal coming off the vertical amplifier YAMP in the schematic is not at a certain level capacitor C9 keeps the timer from restarting so the sweep starts every time the signal reaches the same specific level that allows the timer to start a new sawtooth cycle The triggering level and slope are not adjustable to maintain simplicity CRT Clock TV Scope Page 21 9
20. ful not to touch those terminals when the PCB is powered In the next few steps the PCB will be powered up for the first time If any unexpected problems arise in the next few steps then power off and refer to Troubleshooting starting on Page 23 Now for the moment of truth apply power to the transformer The CRT filament should slowly come to a dim yellow orange glow After about 15 seconds to a minute depending on CRT age and wear a dot should appear somewhere on the CRT screen The dot will usually be out of focus so adjust the INTEN trimmer slightly clockwise until the dot is slightly dimmer Then adjust the FOCUS trimmer until the dot is sharper and smallest Depending on the transformer used the dot sharpness may vary from 0 5mm to 3mm Finally adjust the ASTIG trimmer until the dot is as round as possible Minor readjustments may be necessary later The next check to perform is to adjust the XPOS and YPOS pots and the dot should move horizontally and vertically respectively The CRT itself may need to be rotated until the dot movements match the descriptions This checks that the deflection amplifiers are correctly operating without a signal input Now apply a sinusoidal signal within 5V at a frequency around 100Hz to 5KHz on the center pin of XSEL JP2 The dot should turn into a horizontal line Likewise apply the same signal to the center pin of YSEL JP1 and the dot should turn into a vertical line XSIZE and YSIZE will adjust th
21. ge Yellowish orange Medium White White Medium to Used in monochrome medium short television picture tubes Blue Biue Medium short Photograph recording White White Short Obsolete Originally used in television receivers White Yellowish green Blue medium short Used for radar Yellowish green long Obsolete replaced by P 7 Obsolete Dark trace Outside source of light is very long used for observation Persistence fram seconds to several months Blue Blue Medium short Photographic recording Orange Orange Lon Used for radar Reddish orange Reddish orange Medium Purplish blue Yellowish orange Blue medium short Used for military displays Orange medium where repetition rate is 2 to 4 seconds after excitation is removed Green Green Visible short Television pick up of Ultra violet photographs by Flying very short Spot Scanning Very shart Television pick up of photographs by Flying Spot Scanning Blue short Used for military displays Yellow long Medium to Low frame rate television Medium short Long Radar indicators Medium to High visibility displays medium short Reddish orange Reddish orange Medium Tricolor Medium short Used for color television phosphor screen White White Medium short Low temperature white Sepia Interchangeable with P 4 Green Grean Short Used in Flying Spot Scanner tubes Orange Orange Medium Used for military displays where repetit
22. he correct place Use a DC meter with the ground probe connected to GND to check voltages on the TLO82 IC1 There should be 5 on pin 8 and 5 on pin 4 Beam moves backwards on X and or Y axis clock face is backwards and or upside down Flip the wires leading to X1 and X2 if horizontal is backwards Y1 and Y2 if vertical is backwards Be sure to power off the PCB before reversing these connections Signal does not appear stationary free running in Oscilloscope mode Adjust HSYNC to change the fine frequency so the signal appears clearly on the screen Triggering is not working due to incorrect setup of TSEL Triggering is not present due to weak signal Turn up YSIZE to improve triggering Note that trigger circuitry is basic so not all signals will trigger the sweep nicely A line cuts through the signal in Oscilloscope mode with Frequency Range at highest setting This is normal due to lack of retrace blanking The retrace is visible at higher frequencies How to install panel mount potentiometers Use extension wires from the trimmer pins to the potentiometer Be careful with the ASTIG FOCUS and INTEN potentiometers because they carry high voltages Make sure the metal casing of the potentiometers are not in any way connected to the terminals for insulation In TV mode only a horizontal line appears YSEL JP1 is incorrectly set up The right pin should connect to the center pin either through a shunt wire jumper or th
23. ion of circuits for multiple functions the TV feature requires all the parts under Oscilloscope except for those denoted with an asterisk The miscellaneous parts are not required for the PCB but rather for external wiring or other functions detailed under Notes and at the Page number All the parts come with a suggested part number for Digikey DK Mouser MR STF Electronics STF SparkFun SF NKC Electronics NKC or other sources A small parts kit is available from Dutchtronix www dutchtronix com that will cover all the parts listed under Clock and jumpers JP1 4 for 17 50 Many components often come in different packages and dimensions The information listed under Package describes the case or dimensions of the component that will fit on the PCB Other dimensions may work but likely will not fit as neatly on the PCB Several components have numbers under Package that describes the physical dimensions as follows e For the battery ceramic disc capacitors and crystals the number refers to the spacing between the leads e For electrolytic capacitors the first digit before the dash is the spacing between the leads and the last digit after the dash is the tubular body diameter For example a 3 5 5 package means 3 5mm spacing between leads of a capacitor with a 5mm body diameter Essentials Part Value Description Package Suggested Part Number CRT See CRT Notes on Page 8 Cl 0 001luF 2kV ceramic disc 5 DK 478 4289 1 ND C15 10
24. ion rate is 10 seconds to 2 minutes after excitation is removed Orange Orange Very long Used for radar display Reddish orange Reddish orange Medium Color Television Monitor Service Yellow green Yellow green Long Used for radar display Two color Medium Used as indicator in phosphor screen aircraft instruments Bluish purple Bluish purple Yellow White Yellow white to blue white White Orange Orange Yellow green Yellow green Green Green Medium short Used in cathode ray oscillographs Purple blue Yellow green Long Used for radar display Orange Orange Very long Used for radar display Bluish green Yellow green Very long Used for oscillography radar and visual information storage No data available not registered as yet with EIA CRT Clock TV Scope Page 26 9 30 2008 APPENDIX B CRT BASING DIAGRAMS BASING DIAGRAMS 03 Dla Ga 2 7 Gal TOR o 9 Cars 1092 KZE i DOJ rae INC 3JP1 3JP7 3KP1 3KP4 3KP7 3KP11 IRPI IRPI A 3RP4 post cs vo Dua 2 ucror Ga aa 2 Dua G3 po nov uy Gi AN NC A H H 3WP1 3WP2 3WP11 5ABP1 5ABP4 SABP7 5ABP11 5ADP1 ae OB BS gjon aoe 3 3 Vig2 KO OM 104 12nc RO WN x OREO H H NC H 5CP1 A 5CP7 A 5CP11 A 5CP12 SFP7 A 5FP14 5FP14 A 5FP15 A 5UP1 5UP7 5UP11 5FP4 A 7BP7 A 12DP7 A CRT Clock TV Scope Page 27 9 30 2008 APPENDIX C PCB OPERATIN
25. ire CRT Clock TV Scope Page 16 9 30 2008 Jumper Settings for Mode Selection XYZ Scope Clock Oscilloscope If the builder prefers to use a switch for convenient selection of modes then a 4 pole 4 position rotary switch is recommended for easy selection of all four modes However these switches are difficult to find but 4 pole 3 position types are fairly common Below is a schematic diagram of how a 4 pole 4 position switch can be wired to the PCB in theory If less features are desired and a switch with fewer positions are used then simply ignore wiring to features that are not used 4 POLE 4 POSITION SWITCH WIRING FOR MODE SELECTION XYZ Scope Clock Oscilloscope TY Signal Input Limitations and Workarounds For XYZ Scope mode the input signals for X and Y may not exceed 5V due to the op amp being limited by the power supply Moreover the Z axis responds to positive signals from around 0 7 to 2 volts by shutting off the beam briefly For slightly better Z axis operation and protection of transistor T9 a base resistor in the kilo ohms range such as 10K is recommended Likewise the INPUT signal for Oscilloscope mode may not exceed 5V When fed into the deflection amplifiers signals with amplitudes greater than 5V will appear on the CRT screen with clipping Refrain from feeding higher input voltages or circuit damage may result CRT Clock TV Scope Page 17 9 30 2008 In Oscilloscope Mode the signal should not be greater than
26. is possible to make the CRT work by connecting the anode cap to the HV solder pad Do not attempt to solder a wire to the anode cap as that may damage the CRT Be creative with a paper clip to create a connector for the anode cap Other CRTs may require much higher voltages on the anode cap and cannot be used with the PCB Most electrostatic CRTs do not have an anode cap so the HV solder pad is left unused Anode Cap Final Assembly Steps Carefully check over the PCB to make sure all components are soldered in place and excess leads are clipped off Ensure that there are no loose solder blobs or bridges that could cause a short Do not attach the shunts to the jumpers so the PCB is in XYZ Scope mode and do not connect any of the XYZ inputs to a signal source If a rotary mode selector switch is used as detailed in the User Manual under Mode Selection on Page 16 then set it to XYZ Scope mode Rotate the INTEN trimmer potentiometer fully counter clockwise for full brightness The ASTIG and FOCUS trimmers should be centered Leave all the jumpers disconnected so the PCB is in XYZ Scope mode The XPOS and YPOS trimmers should be centered XSIZE and YSIZE should be turned fully counter clockwise for minimal amplifier gain If only Oscilloscope mode or Oscilloscope and TV modes are used then refer to Frequency Range Switch Wiring on Page 19 for adding a 1 pole 6 position rotary switch If TV mode is desired but not Oscilloscope mode then refe
27. isting of many American CRT pinouts and data If the CRT of choice is not listed there then the next best bet is to search through online tube datasheet websites The diagrams reflect the pins of the CRT base Similarly CRT socket pins are numbered clockwise when viewed from the bottom solder end The PCB has 9 solder pads for CRT connections but for most of the CRTs listed under CRT Notes on Page 8 only 8 of the pads are needed The older American CRT pinouts shown in Appendix B have a different convention for labeling the pins and are listed under American CRT Pin below A summary of the solder pads on the PCB and connections are listed below PCB pad Description American CRT Pin K Cathode K Al Anode 1 G3 A2 Anode 2 G2 G4 CL ultor Gl Grid Gl X1 Horizontal Deflection 1 DJ1 X2 Horizontal Deflection 2 DJ2 HV Anode 3 if present G3 CL post ultor anode cap Y1 Vertical Deflection 1 DJ3 Y2 Vertical Deflection 2 DJ4 CRT Clock TV Scope Page 11 9 30 2008 Sockets for older CRTs are difficult to find but makes assembly easier An alternative is to use individual wires with appropriate pin connectors at the ends Pin connectors from hard disk drive connectors on PC power supplies work great with most CRT pins The pins labeled as H are the filament heater pins and connect directly to the transformer as described in Transformer Wiring on Page 10 If the CRT comes with an anode cap such as the 3JP1 shown in the picture below then it
28. located is shown below Frequency Range Switch Wiring For Oscilloscope Mode it is assumed that the builder will want to use panel mount potentiometers and switches for easy and convenient use The horizontal sweep generator has 6 capacitors from 0 001uF to 47uF to change the range of sweep speeds These capacitors are connected to solder pads 1 to 6 on the lower right of the PCB The common terminal that leads to the sweep generator is at solder pad 7 The following illustration shows how to wire a l pole 6 position rotary switch to these pads to provide a range selector switch for the horizontal sweep CRT Clock TV Scope Page 18 9 30 2008 Sweep Frequency Range Switch Wiring FASTER SLOWER If the builder prefers a simpler alternative small pins may be mounted to each solder pad and a short wire with a clip from pad 7 may be used to select a range TV Mode and No Oscilloscope Mode If TV mode was built into the board then Oscilloscope mode comes with TV mode as a free bonus but fixed at a high frequency range due to the lack of C3 to C7 If the builder includes C3 to C7 then the full Oscilloscope mode is included The horizontal sweep used in Oscilloscope mode is also used in TV mode but remains fixed at a high frequency range to synchronize to the horizontal sync pulses from the input composite video Rather than a frequency range switch that is not needed for TV mode if Oscilloscope mode will never be used a short piece of wire ma
29. luding the Breakout Board for FT232RL USB to Serial at Sparkfun Electronics www sparkfun com or the RS232 to TTL 3V 5 5V Converter Kit at NKC Electronics www nkcelectronics com Mode Selection Jumpers JP1 to JP4 are used for selecting a mode but a switch may be preferred for quick and convenient selection of modes see Page 17 for more details If the builder only intends to hardwire a single feature on the PCB then wires may be used in place of the jumper pins Below is a close up picture of the jumper area at the center of the PCB The center pin of XSEL JP2 and YSEL JP1 leads to the inputs of the deflection amplifiers Likewise the center pin of ZSEL JP3 leads to the Z axis circuitry The left pins on JP1 through JP3 are output signals from the scope clock The right pins of JP1 and JP2 are from the 556 sweep generators and the right pin of JP3 is video output all of which are used in both Oscilloscope and TV modes TSEL JP4 stands for Trigger Select because half of the 556 timer is used in both Oscilloscope and TV mode The right pin of TSEL JP4 is the horizontal sync for TV mode and the left pin of TSEL is the output of the vertical amplifier for triggering the sweep to the input signal in Oscilloscope mode Please refer to the following diagram for a summary of the jumper settings The black rectangles are either shunts or jumper wires The blue lines refer to external signals that are fed into these pins using a probe or a w
30. nd make sure it is slow blow If 5V is not present on the filament pins then check if 5VAC winding of transformer has voltage If not winding is open and transformer should be replaced CRT filament lights but nothing appears on the screen Rotate the INTEN trimmer completely counter clockwise for full brightness Set the mode to XYZ Scope and try to locate a dot by adjusting XPOS and YPOS If Oscilloscope mode is available then use it because a horizontal sweep would help locate the beam easier Check Appendix C for a list of expected voltage measurements CRT may be either too large requires a higher accelerating voltage on the anode cap that cannot be provided by the PCB or weak due to heavy use in the past Consider obtaining another CRT Dot line or picture appears on screen but very dim Rotate the INTEN trimmer completely counter clockwise for full brightness If the CRT remains dim then the tube is either too large requires a higher accelerating voltage on the anode cap that cannot be provided by the PCB or weak due to heavy use in the past Consider obtaining another CRT Power transformer may not be suitable for the CRT size 350VCT is sufficient for many 2 and 3 CRTs but most likely not for 5 CRTs 550VCT is a bit high for 2 or smaller CRTs but sufficient for 3 and some 5 CRTs Dot appears but does not move when XPOS or YPOS trimmers are adjusted Check that the ZTX458 transistors T2 T3 T4 T5 are i
31. nstalled properly If accidentally reversed they are most likely ruined so replacement is recommended Check R1 R9 R5 R4 R8 and R18 to make sure they are soldered in the correct place Use a DC meter with ground probe connected to GND and the other probe on the center pin of the XPOS or YPOS trimmer Be very careful when handling the board due to high voltages Always power off before handling the board Meter should read a voltage between 5 and 5 If not check that the trimmer is soldered in place correctly or replacement is recommended CRT Clock TV Scope Page 23 9 30 2008 Dot appears and is movable but does not do anything with a signal input TLO82 op amp IC1 may be installed backwards Check that the notch on the chip matches the IC outline notch on the PCB TLO82 IC1 may be damaged Use a DC meter with the ground probe connected to GND to check voltages on the TLO82 IC1 There should be 5 on pin 8 and 5 on pin 4 Check the XSIZE and YSIZE trimmers to ensure they are soldered in place Also check R10 and R12 to make sure they are soldered in place correctly Dot appears moveable but constrained in an area of the screen Only a quarter of the clock appears on the screen with a pie shape Position and Gain pots set incorrectly Turn down XSIZE and YSIZE by rotating completely counterclockwise then recenter the image via XPOS and YPOS then resize Check R1 R9 R5 R4 R8 and R18 to make sure they are soldered in t
32. or resistor resistor resistor resistor YPOS potentiometer XSIZE potentiometer XPOS potentiometer YSIZE potentiometer resistor resistor ASTIG potentiometer resistor INTEN potentiometer FOCUS potentiometer CRT Socket See Notes on Page 11 Hammond See Transformer Notes on Page 8 Description lithium cell ceramic disc ceramic disc Page 5 DO 41 DIP 8 TO 92 TO 92 TO 92 TO 92 TO 92 TO 92 TO 92 Package DK 1N4004 TPMSCT ND DK 296 1780 5 ND DK MC78L0S5SACPGOS ND DK MC79LOSACPGOS ND MR 538 22 28 4203 MR 151 8000 DK ZTX458 ND DK ZTX458 ND DK ZTX458 ND DK ZTX458 ND DK ZTX458 ND DK CF1 42 2K5 RCT ND DK CF1 456K5 RCT ND DK CF1 456K5 RCT ND DK CF1 44 7K5 RCT ND DK CF1 44 7K5 RCT ND DK CF1 456K5 RCT ND DK CF1 456K5 RCT ND DK CF1 44 7K5 RCT ND DK CF1 42 2K5 RCT ND DK CF1 410K5 RCT ND DK CF1 4470K5 RCT ND DK CF1 410K5 RCT ND MR 531 PT10MH 10K MR 531 PT10MH 100K MR 531 PT10MH 10K MR 531 PT10MH 100K DK CF1 41M5 RCT ND DK CF1 44 7K5 RCT ND MR 531 PT1OMH 1M DK CF1 447K5 RCT ND MR 531 PT1OMH 1M MR 531 PT1OMH 1M STF 270X Suggested Part Number MR 614 CR1225FV LF DK 478 1831 ND DK 478 1831 ND 9 30 2008 C25 22pF ceramic disc C26 22pF ceramic disc C27 0 1uF ceramic disc C28 10uF radial electrolytic D9 BAT42 schottky diode D10 BAT42 schottky diode D12 1N4148 signal diode D13 1N4148 signal diode IC6 ATMEGA168 20 preprogrammed
33. pacitances of the CRT Moreover the CRT is sensitive to its orientation due to the Earth s magnetic field so XPOS and YPOS readjustment may be necessary when moving the clock to a different location Once the CRT adjustments are complete and picture quality is good the clock operates exactly like the original Scope Clock available on www dutchtronix com The pushbutton switch S1 at the front of the PCB is used to change the clock settings Refer to the Dutchtronix website for operating instructions However note that this PCB lacks a LED and a RS232 level shifter The AVR still can be programmed with the aid of an external RS232 level shifter board Refer to Programming the AVR on Page 15 for further details Do not try to add a LED to the circuit because it causes fluctuations in the low voltage supply and interferes with the picture Oscilloscope Mode Setup and Usage If the Oscilloscope feature was added then power off If not done so follow instructions under Frequency Range Switch Wiring on Page 19 Then proceed to add the shunts on the jumpers for this mode using Mode Selection on Page 16 for instructions If a rotary mode selection switch was used then rotate the switch to Oscilloscope mode Apply power A line or a dot should appear on the screen as the CRT warms up Adjust XSIZE to vary the width of the sweep horizontal line Due to basic triggering and lack of retrace blanking XSIZE should be adjusted so the beginning of the sweep i
34. plifiers which do not have a heavy current demand so the filter capacitors do not have to be as large as those on the 5V supply for steady SVDC Potentiometers R33 R35 and R36 provide an adjustable range of appropriate voltages to the CRT elements C17 and C18 are wired in series to make an equivalent capacitor rated at luF 900V to handle the highest negative potential of 770V without a problem R11 serves as an equalizing and bleeder resistor for C17 R35 and R36 serves a similar purpose for C18 Deflection Amplifiers XYZ Scope T4 T5 R2 R3 R5 R8 and R9 form a transistor difference amplifier for the horizontal with a gain that is governed by the size of R9 The two transistors share emitter currents through R9 so one transistor is affected when the other draws more emitter current As a result the collector voltages on both transistors change at the same amount but in different directions resulting in uniform deflection of the beam A mechanical analogy of the collector voltage behavior is to visualize a seesaw as collector voltage 1 goes up collector voltage 2 must go down at the same distance so there is a push pull effect on the beam by the deflection plates R15 sets the bias voltage on T5 to change the offset of the collector voltages and thereby control centering A smaller value for R9 increases the gain and a larger value decreases the gain Likewise T2 T3 R7 R6 R4 R18 and R1 for the vertical serve the same purpos
35. r to TV Mode with No Oscilloscope Mode on Page 19 for adding a jumper on solder pad 6 and 7 Stand off posts or feet at the corners of the PCB are recommended to keep the PCB bottom off the surface of the table or workbench CRT Clock TV Scope Page 12 9 30 2008 USER MANUAL Powering Up for the First Time At this point the PCB should be populated with all the components under Essentials plus additional features and wired to the transformer and CRT Carefully check that the transformer has been correctly wired to the PCB and CRT Make sure the primary circuit including the power cord are adequately insulated and not in contact with the secondary circuit including the PCB and transformer This is essential for isolation and safety The PCB carries potentially lethal voltages with the largest potential difference at around 1000 volts Try to refrain from using both hands when making adjustments or measurements on the PCB and use only one hand at all times when possible If for any reason the PCB has to be powered off the high voltage capacitors will still hold dangerous charges Do not attempt to manually discharge any of the capacitors with a screwdriver or a jumper of some sort as that may damage the circuit Anytime the term power off appears remove power and wait a few minutes for the capacitor charges to bleed off before handling the PCB Moreover the metal terminals on ASTIG FOCUS and INTEN have 200 to 400 volts across them so be very care
36. rough the mode selection switch Vertical oscillator is not running due to VSYNC being way off Readjust VSYNC Check that vertical deflection amplifier is functional by feeding a signal no larger than 5 into the center pin of YSEL JP1 If not TL082 IC1 may need to be replaced Check that the vertical ZTX458 transistors T2 T3 are installed properly If accidentally reversed they are most likely ruined so replacement is recommended Check that 0 22uF C8 is properly installed CRT Clock TV Scope Page 24 9 30 2008 In TV mode no picture appears e No composite video is present on VIN Make sure the ground shield of the video cable is connected to GND e INTEN may be set too high so readjust for a lower brightness setting e Check R34 R17 T9 and C1 to make sure they are soldered in place correctly If T9 was inserted backwards it is most likely ruined and replacement is recommended e Check C13 C14 R30 R31 R32 and T8 to make sure they are soldered in place correctly In TV mode a picture appears but with horizontal streaking or overlay e Readjust HSYNC e If there is some streaking and it changes with the video then that is normal due to the simplicity of the Z axis circuit In TV mode the picture appears totally black and white with no gray in between e Adjust INTEN to gain some gray area but most of this picture quality is normal due to the simplicity of the Z axis circuit 5V reads as 0 on the DC meter e Che
37. s off screen for a cleaner sweep trace Adjust XPOS if necessary to center the horizontal line Adjust YPOS to center the line vertically Apply a signal that is no larger than 5V at a low frequency ranging from 100Hz to 10KHz to the middle pin of YSEL JP1 or to the input of the rotary selector switch if that is used Use the Frequency Range selector switch to change resolution to see the signal better Adjust YSIZE to vary the amplitude of the signal on the screen and this will also improve triggering Adjust HSYNC until the trace is clear and stable Refer to Page 18 under Signal Input Limitations and Workarounds for more information on suitable signals to feed into the oscilloscope CRT Clock TV Scope Page 14 9 30 2008 TV Mode Setup and Usage First power off the PCB If the TV feature minus the Oscilloscope feature is desired then skip this paragraph If the TV feature and the Oscilloscope feature were desired then if not done so follow instructions under Frequency Range Switch Wiring on Page 19 to add a switch Then proceed to add the shunts on the jumpers for this mode using Mode Selection on Page 16 for instructions If a rotary mode selection switch was used then rotate the switch to TV mode Finally proceed to set the Frequency Range switch to the highest frequency setting If the TV feature minus the Oscilloscope feature is desired instead then if not done so follow instructions under TV Mode with No Oscilloscope on Page 19 for a
38. tap into the CT solder pad The 6A and 6B solder pads are for the low voltage winding of the transformer preferably the 6V 0 6A winding The 5V 0 6A winding is recommended for operating the CRT filament Although most CRT filaments operate off 6V 0 6A running it at 5V runs the filament slightly cooler for longer life However if preferred the 5V 0 6A winding may be fed into 6A and 6B and the CRT filament may run off the 6V 0 6A winding instead On the following page Page 11 is a wiring diagram of the transformer connections to the PCB The transformer used in this diagram is a Hammond 270X but any other transformer with similar specifications as described on Page 8 should work fine Note that the primary circuit has a 0 5A slow blow fuse for the Hammond 270X but more powerful transformers may require CRT Clock TV Scope Page 10 9 30 2008 larger fuses Although the fuse may be eliminated entirely without problems because transformer failure is highly unusual please use a fuse for additional safety in case of unforeseen failure The PCB only deals with the secondary windings of the transformer so the switch power cord and fuse holder for the primary circuit of the transformer are additional components that are listed under the Miscellaneous category on Page 7 TRANSFORMER WIRING 120 4C Hammond 270 TO CRT Se FILAMENT PAR Sw 480VCT 04A 0 54 FUSE slow blow CRT Socket and Wiring Please refer to Appendix B on Page 27 for a l
39. uF 450V radial electrolytic 5 13 DK P13671 ND C16 luF 450V radial electrolytic 3 5 8 DK P5340 ND C17 2 2uF 450V radial electrolytic 5 10 5 DK P5341 ND C18 2 2uF 450V radial electrolytic 5 10 5 DK P5341 ND C19 100uF radial electrolytic 2 5 DK P5137 ND C20 470uF radial electrolytic 3 5 8 DK P5141 ND C21 1000uF radial electrolytic 5 10 5 DK P5142 ND C22 470uF radial electrolytic 3 5 8 DK P5141 ND D3 1N4007 1000V 1A diode DO 41 DK 1N4007 TPMSCT ND D4 1N4007 1000V 1A diode DO 41 DK 1N4007 TPMSCT ND D5 1N4007 1000V 1A diode DO 41 DK 1N4007 TPMSCT ND D6 1N4007 1000V 1A diode DO 41 DK 1N4007 TPMSCT ND D7 1N4004 400V 1A diode DO 41 DK 1N4004 TPMSCT ND CRT Clock TV Scope Page 4 9 30 2008 D8 1N4004 IC1 TL082 IC4 78L05 IC5 79L05 JP1 4 T2 ZTX458 T3 ZTX458 T4 ZTX458 T5 ZTX458 T9 ZTX458 R1 2 2K 1 4W R2 56K 1 4W R3 56K 1 4W R4 4 7K 1 4W R5 4 7K 1 4W R6 56K 1 4W R7 56K 1 4W R8 4 7K 1 4W R9 2 2K 1 4W R10 10K 1 4W R11 470K 1 4W R12 10K 1 4W R13 10K R14 100K R15 10K R16 100K R17 1Meg 1 4W R18 4 7K 1 4W R33 1Meg R34 47K 1 4W R35 1Meg R36 1Meg SOCKET TRAFO 270X Clock Part Value BATTERY 3 volt C23 0 1uF C24 0 1uF CRT Clock TV Scope 400V 1A diode dual op amp 5V 100mA regulator 5V 100mA regulator 0 1 header 20 pos Shunts for jumpers 400V 0 5A NPN 400V 0 5A NPN 400V 0 5A NPN 400V 0 5A NPN 400V 0 5A NPN resistor resistor resistor resistor resistor resistor resistor resist
40. ure will appear more than once or with an overlay so continue to adjust HSYNC until the picture reappears as a single frame Readjust XSIZE YSIZE XPOS and YPOS if necessary to center and resize the picture Adjust INTEN for best picture appearance and FOCUS to improve sharpness if necessary Do not expect a picture quality that is comparable to a cheap handheld TV let alone high definition On the other hand congratulations on making an incredibly simple TV video monitor from scratch Some streaking and blurring of the picture is normal due to simplicity and poor response in the Z axis circuit Programming the AVR Microcontroller for Clock Mode If the Clock mode is used then a preprogrammed ATMEGA 168 20 is available from www dutchtronix com If the microcontroller needs to be upgraded to the latest clock software from Dutchtronix then the PCB comes with a connector at the lower left shown in the following CRT Clock TV Scope Page 15 9 30 2008 picture that provides all the necessary connections 5 GND TX RX for an external level shifter board The TX and RX pins on the PCB are TTL levels and incompatible with RS232 signals An external level shifter is required because RS232 ports typically output 3 to 15V whereas the AVR supports 0 to 5V The level shifter takes care of the difference in voltage magnitudes polarity and ranges Prefabricated level shifter boards are available to convert RS232 or USB signals to TTL levels inc
41. y be used as a jumper between solder pad 6 and 7 as illustrated in the following picture CRT Clock TV Scope Page 19 9 30 2008 THEORY OF OPERATION The schematic is included in Appendix D Power Supply Diodes D3 and D5 performs full wave rectification on the high voltage secondary of the transformer feeding into 240A CT 240B Capacitor C15 filters out the ripples so the HV line has fairly steady 245 to 385VDC that is essential for the deflection amplifiers D4 D6 C16 C17 and C18 creates a voltage doubler circuit off the 240B CT secondary to create about 490 to 770VDC for the negative supply The cathode is set very negative so the deflection amplifiers only have to handle a few hundred volts with respect to ground The Z axis circuitry uses a coupling capacitor C1 to provide the appropriate bias on the grid to shut off the beam for a short moment when the voltage on the collector of T9 changes Most of the time the Z axis will receive fast changing signals so the circuit serves its function without resorting to a more expensive DC coupled design D7 creates positive half wave DC that is filtered heavily by C21 then IC4 regulates the voltage to 5 at 100mA maximum and the output is filtered again with C20 for a relatively steady 5VDC supply Similarly D8 creates negative half wave DC that is filtered by C22 regulated to 5V at 100mA max by ICS and the output filtered again by C19 The 5V is only used by the deflection am
Download Pdf Manuals
Related Search