SensAlarm Plus Remote Kit manual
Contents
1. SENSA am PLUS Remote Sensor Kits Installation Manual Document No 360 0127 01 Revision C A EA E ES AS aE SA DET SILLS IVE Sensidyne LP 1000 112 Circle N Suite 100 St Petersburg Florida 33716 USA 800 451 9444 1 727 530 3602 1 727 539 0550 fax web www sensidyne com e mail info sensidyne com SensAlarm Plus Remote Sensor Kit WARNINGS PAGE WARNINGS READ AND UNDERSTAND ALL WARNINGS BEFORE USE Read and understand ALL warnings before using this product Failure to read understand and comply with ALL warnings could result in property damage severe personal injury or death Installation must be done in accordance with all local electrical codes Follow standard grounding procedures when wiring the Remote Sensor Kit All warnings and installation instructions should be read and understood as contained in the SensAlarm Plus Universal Gas Monitoring System User Manual P N 360 0126 01 Sensor Interface Assembly must be mounted such that condensation and dust does not collect on the Sensor Read and understand ALL applicable federal state and local environmental health and safety laws and regulations including OSHA Ensure complete compliance with ALL applicable laws and regulations before and during use of this product The user installer must understand the Hazardous Area Protection Concepts and Area Classifications applicable to their operation UNDER NO CIRCUMSTANCES should this produc2. v UKAS QUALITY MANAGEMENT 061
3. SenAlarm Plus Models SensAlarm Plus Remote Sensor Kit P N 821 0301 01 contains the following items Note References in brackets refer to letter number references in Figure 1 RENO aske Sensidyne P N DESCRIPTION 550 4003 01 Aluminum Condulet Nipple 34 NPT Qty 1 522 0002 02 Cover Condulet Qty 1 Shown Assembled A 522 0002 03 Gasket Neoprene Qty 1 Shown Assembled AS tiets 522 0002 04 Junction Condulet with two 90 84 NPT openings A 4 A 61 7017291 Watertight Cable Entry Cable Strain Relief Qty 2 Not shown 205 0081 01 Splice 2 pos Qty 4 380 0021 01 Bracket Weld Assembly Black Anodized Qty 1 Cable Specification 18AWG x 4 Conductor Shielded uH ft lt 0 2 pf ft lt 60 Max length 100ft 30m Cable to be Customer Supplied Belden 27326AS or equivalent Installation Refer to Figure 1 and install the Remote Sensor Kit as follows 1 Fasten the Bracket A 7 to the desired location Sensor Interface Assembly must be mounted such that condensation and dust does not collect on the Sensor Thread the wires from the Sensor Interface Assembly A 8 through the Bracket A 7 and Nipple A 2 tighten to secure Note If you are using tools to tighten the Sensor Interface Assembly make certain you use them ONLY on the Aluminum hex nut which came attached to the top of the Sensor Interface Assembly 2 Thread the wires from the Sensor Interface As
4. sembly A 8 into the lower opening of the Junction Condulet A 3 Tighten the the Junction Condulet A 3 to the Nipple A 2 Note If you are using tools to tighten the Sensor Interface Assembly make certain you use them ONLY on the Aluminum hex nut which came attached to the top of the Sensor Interface Assembly 3 Thread the customer supplied remote cable A 5 through the Watertight Strain Relief A 6 and tighten to secure remote cable 4 Wire the remote cable to the interface using 4 of the Splices provided Wire accordingly R Red B Black O Orange Y Yellow Install the Condulet Gasket and Cover 5 Route and secure the customer supplied remote cable A 5 to the SensAlarm Plus Location A 1 7 Thread the wires through the Watertight Strain Relief A 4 and tighten to secure remote cable 8 Wire the remote cable to the SensAlarm A 1 Wire accordingly R Red B Black O Orange Y Yellow Connect the shield wire to the TB2 Pin 5 Barrier PCA in the SensAlarm Plus Sensidyne Document No 360 0127 01 Rev C 5 SensAlarm Plus Remote Sensor Kit Floor Mount A 8 Ceiling Mount Invert Mounting Bracket A 7 Figure 1 Remote Sensor Rit Installation Sensidyne Document No 360 0127 01 Rev C JE IVES Y TEE Sensidyne LP 1000 112 Circle N Suite 100 St Petersburg Florida 33716 USA 800 451 9444 1 727 530 3602 1 727 539 0550 fax web www sensidyne com e mail info sensidyne com
5. t be used except by qualified trained technically competent personnel and not until the warnings User Manual labels and other literature accompanying this product have been read and understood Failure to read and understand the User Manual may result in preventable severe personal injury or death DO NOT remove cover or alter any label or tag on this product its accessories or related products DO NOT operate this product should it malfunction or require repair Operation of a malfunctioning product or a product requiring repair may result in serious personal injury or death DO NOT attempt to repair or modify instrument except as specified in the Operation amp Service Manual If repair is needed contact the Sensidyne Service Dept to arrange for a Returned Material Authorization RMA See Section in the SensAlarm Plus Universal Gas User Manual P N 360 0126 01 for details The SensAlarm Plus Universal Gas Monitoring System is an ambient air monitoring device Restricting the access of ambient air to the sensor may result in less than optimal monitoring performance Sensidyne Document No 360 0127 01 Rev C 3 SensAlarm Plus Remote Sensor Kit NOTES 1 The sensor may be oriented from horizontal down to vertical The surface of the sensor must be protected from moisture condensation and dust 4 Sensidyne Document No 360 0127 01 Rev C SensAlarm Plus Remote Sensor Kit 821 0301 01 Remote Sensor Kit for use with
Download Pdf Manuals
Related Search