rev 200SG KIT-AA rev 200SG KIT-AA
Contents
1. bike e The orange wire is the remote turn on lead and tells the amp to turn on whenever it sees 1 2v 5 amp min Unplug the factory center wire on the cigarette lighter e Plug the orange lead from the amplifier directly onto the lighter using the female connector e Plug the factory lighter wire to the male take off connector which is part of the amps orange turn on lead IMPORTANT If you do not attach the orange wire from the amp to the center wire at the cigarette lighter the amplifier will not turn on If the factory fuse for your cigarette lighter is blown and your cigarette lighter does not work your amplifier will not turn on ROUTING THE POWER HARNESS f For 98 06 bikes the power harness will pass under the inner fairing where the throttle and idle cables pass through on the brake side of the bike The harness is designed to be routed between the frame backbone and gas tank on the brake side of the bike and come out just behind the gas tank You MAY need to undo the back bolt of the gas tank and pivot the tank up to allow the harness to pass through at the back of the gas tank Be sure to re install this bolt and torque to factory specs For 2007 2013 bikes the balance of the main wire harness will pass under the inner fairing where the main wire harness passes through on the brake side of the bike Loosen the tank console and run wires up and over the gas tank but under the tank console There2. bike everything will work fine Please remember that car radios are designed to work in an envi ronment with little or no exhaust or wind noise Many car radios have features such as equalizers loudness contours surround effects etc all designed for a quiet environment and all of which will hurt your ability to hear your motorcycle system at speed if left on Please take a minute and turn as much of these features off With a car radio in your bike the only adjustments you should be able to access for best performance are volume bass treble balance and fader 4 If you re using an external device to supply music through the radios AUX port we have an article on our website that can help make your peripheral audio device sound as good as it can The article is at http www hogtunes com techzone_files Level_matching pdf TECHNICAL SPECIFICATIONS Hogtunes REV 200 AA Amplifier RMS Power at 2 Ohms 6 5 100 watts x 2 Freq Response ceceeeeeeeeerees 30hz 25khz Fuse GLAM suaviasien sencienvncie 15 amp Hogtunes 352F AA Front Speakers Power Handling ossessi 100 RMS 150 Peak Frequency Response 55hz 25Khz DE MSUIVIIVG eresse 92 db 1watt 1meter Nominal Impedance 0 2 0 Ohms COOMFGGIORS aissos sigen EXTREME WARRANTY INFORMATION y Please Record Your Amplifier s Serial Here Hogtunes speakers are warranted for a period of 20 years The REV 2
3. easy way to add rear speakers to your bike if you ve added a King Tour Pak Hogtunes rear speaker pods come with a wire harness set up for quick detach tour paks that will plug right into the expansion port on the amp IMPORTANT Since the RADIO power will be used to power the rear speakers you must use rear speakers specific to your year of bike Use expansion port to send radio s built in power to a second set of speakers rears on Non Ultra Models HOGTUNES m m m m m m m n 7 Optional HF 1 Tweeter Pod SYSTEM UPGRADE 2 A This system has the incredible power of 2 REV 200 AA Amplifiers to your bike The first amp will run the 5 25 fairing speakers and HF 1 Tweeter Pod if present The second amplifier is used to power a set of 692 2 Lids FL 7W fairing lower woofers or rear tour pak speakers For all Standard Classic Ultra Street Glide models the purchase of Hogtunes 2CHSP adaptor kit is required The metal plate in that kit is used to bolt the second amplifier into your fairing between the brake side speaker and radio Use supplied blue plug to send signal from expansion port of first amp to input of second amp HOGTUNES OGTUNES Optional HF 1 Tweeter Pod SYSTEM UPGRADE 3 f This system adds a Hogtunes 4 channel amp where 2 of its channels would power the front speakers and tweeter pod if present and the other 2 channels would power rear speakers or fairing lower woo
4. products will play much louder than the Original Equipment which can be a distraction to the rider and or passenger Please use caution when adjusting or playing your stereo at high volume especially in traffic You are a valued customer so please Ride Alert Arrive Alive www hogtunes com
5. 00 AA Amplifier is warranted for 3 years from original purchase date Proof of purchase is required for all warranty claims The warranty applies to the original retail customer and is not transferable Please contact Hogtunes for all warranty claims Products found to be defective during the warranty period will be repaired or replaced with a product deemed to be equivalent at Hogtunes sole discretion Hogtunes complete warranty policy is available on our website at www hogtunes com warranty html What Is Not Covered 1 Any expense related to the removal or re installation of Hogtunes products 2 Repairs to these products performed by anyone other than Hogtunes 3 Subsequent damage to any other components A Any product purchased from a non authorized Hogtunes dealer 5 Damage to Hogtunes products due to an accident or collision 6 Hogtunes Amplifiers with broken or removed warranty void stickers 7 Damage due to water from custom installations 8 Damage from incorrect installation improper use abuse or modifications 9 Damage to inbound product due to improper packing Harley Davidson Electra Glide Road Glide Street Glide Ultra Classic Tri Glide CVO Screamin Eagle and Tour Pak are Trademarks and or Registered Trademarks of Harley Davidson Inc Milwaukee Wisconsin USA and if Used or Implied are for Reference Only There is No Affiliation Between Harley Davidson Inc and Hogtunes Inc 11 Hogtunes
6. Audio Solutions For The Great American Cruiser REV 20056 KIT AA High Performance Front Speaker and Amplifier Kit FOR USE ON 1998 2013 BATWING MODEL BIKES WITH FACTORY RADIOS INSTALLATION MANUAL Thank you for choosing the Hogtunes REV 200SG KitAA for 1998 2013 Batwing Model Bikes Since positive word of mouth is the best way to grow our business we want your new system to work as well as it was designed to If you have any questions or concerns we are here to help The REV 200 AA Amplifier is a Class D design We chose this design because it yields plenty of power is easy on the bikes charging system and produces little heat It should be understood that ALL Class D amplifiers may cause a reduction in FM reception Nothing is affected when playing CD MP3 Satellite radio or any other music device FM reception will differ and depend on the condition and type of antenna that you are using and although every effort has been made to minimize any loss we strongly advise against the use of in fairing or hidden antennas with Class D amplifiers for best FM reception To help protect your bike s electrical system and battery the amp has a built in feature where it will turn itself off if it sees less than 10 5 volts whether the bike is running or not If you re listening to your stereo while not riding this feature can help protect your battery so the bike can still start If you re riding and the amp shuts off this coul
7. aker side speaker Optional HF 1 Tweeter Pod WIRING THE AMPLIFIER A Step 1 Step 2 Locate the main power harness and plug it into the matching connector on the amplifier Locate the 8 pin harness and plug it into Audio Input on the side of the amp e On the audio input harness locate the yellow black pair of wires with the male connectors e Unplug the factory speaker wires on the clutch side of the bike and plug the yellow black wires in to those They will only go in one way e Also on the audio input harness locate the green black pair of wires with the male connectors Unplug the factory speaker wires on the brake side of the bike and plug the green black wires in to those NOTE The blue 4 pin plug with black wires on the input harness is an expansion port which is used to send music to a second amp or is used to send radio power to run other speakers on the bike You can see how the expansion port can be used in the system upgrade section of this manual Step 3 Step 4 e On the opposite side of the amp are 3 75mm wires ending with a A pin black connector This plug sends amplified power to your speakers Locate 4 pin black plug wire harness with brown black and blue black wires and plug it into the amplified output plug e The blue black wires will plug directly to the speaker on the brake side of the bike The brown black wires will plug directly to the speaker on the clutch side of the
8. d be showing a potential issue with your charging system If this feature is activated and the amp shuts off it will turn the amp back on again if the voltage exceeds the 10 5 volt threshold A video version of this manual is available at www hogtunes com If you still need assistance please consider a professional installation by your motorcycle dealer Hogtunes Contact Information Email tech hogtunes com Tel 705 719 6361 2 GETTING STARTED Step 1 Remove the seat and both wires and from the battery Step 2 Remove the outer fairing headlamp assembly and set it aside Refer to a service manual if you need help with this NOTE A towel on the front fender can help prevent scratches or dings from dropped tools or fasteners etc Expletives will also be kept to a minimum Step 3 Take the 2 wires off each front speaker by gently pulling one at a time Undo the screws that attach each speaker grill assembly to the inner fairing and remove Pull the stock speaker out of each grill assembly Step 4 Clip the Hogtunes speaker into each grill assembly Position your new speaker grill assembly onto the inner fairing and re attach each one using the OE screws Although a hand driven tool is suggested for this the screws need to be tight enough so the speaker grill assembly will not rattle during riding and potentially cause a false warranty claim Diagram 1 2 Standard Street Glide EG Class
9. fers The original 2 channel amp would power 692 2 lids or lower speakers You can literally build the system the way you want based on the body work you have on your bike This can be done at any time all bolt in all plug and play Hogtunes 2CHSP mounting plate is required to bolt the REV 200 AA into your fairing Use supplied blue plug to send signal from expansion port of first amp to input of HOCUS second amp Saddle bag lid 6 x9 speakers or 7 fairing lower glove box woofers ADJUSTING YOUR SYSTEM PLEASE READ A In order to make your new system perform as good as it was designed please take a minute to understand and follow these tips 1 Set your Automatic Volume Control AVC to 3 bars After extensive on road testing we found that this AVC position works and sounds best Your new amplifier has been specifically set up for this radio setting 2 Your Hogtunes system is designed specifically for a motorcycle at speed Exhaust noise and wind noise have been taken into careful consideration in how your system performs How your new system sounds in a driveway or garage is radically different from how it will sound at highway speeds Although your system was set up with a factory radio with its bass and treble controls in the middle position if you feel the need to make adjustments please do so carefully at your normal cruising speed 3 If you have an aftermarket car radio on your
10. ic Ultra Classic Shown mounted No CB XM Module Present on top of CB Module The amplifier gets mounted to the top of the factory radio using the supplied hook and loop adhesive and must sit so you can read the badge on top of the amplifier as in diagram 1 1 The amplifier needs to mount as far back on the radio as possible so the fairing can go back on The minimum distance from the back of the radio to the most forward edge of the amplifier is 5 8 15mm On pre 2006 model bikes it is a tight fit but will go 2006 2013 Advanced Audio radios have a bump on top of the radio that runs from front to back down the center of the radio Cut the adhesive in half and apply each piece on either side of this bump The amp will then mount flush Most adhesives work best at room temperature or higher NOTE 2006 2013 Ultras have the CB module on top of the radio The amp will adhere on top of the CB module so it is half on half off this module as shown in Diagram 1 2 The supplied adhesive is plenty strong for this The amp can adhere on top of the CB and one other module without issue 3 AMPLIFIER WIRING DIAGRAM f Clutch side factory Brake side factory speaker wire plugs into speaker wire plugs into yellow black on amp green black on amp Orange wire goes I OGTUNES to center pin on cigarette lighter Power and ground DIRECT to battery Brown Black Blue Black wire plugs wire plugs into clutch into Brake side spe
11. is a provision on the front of the tank console for wires to pass Secure the amplifiers harness to the bikes factory harness using zip ties When correctly installed the power and ground wires are the right length to connect onto the battery e Attach the red wire to the positive battery terminal and the black wire to the negative battery terminal The factory battery wires are also re installed at this point Turn the ignition of the bike to the on position and play the stereo at low volume to verify the amplifier is working fine IMPORTANT With all wires secured turn the front wheel to each extreme side making sure that any wires cannot bind or impede the steering of the motorcycle Failure to do so can cause an accident resulting in serious injury or death On the brake side of the amplifier is the amp level switch The switch has 3 positions labeled 3 O and 3 e If the expansion port has been used to power additional speakers use the switch to set the balance between the amplified fairing speakers and additional speaker powered by the radios built in power e If you have a dual amp system you can use the switches on each amp to balance the level of sound to each set of speakers as a means to tailor the sound to your liking In a multi amplifier system this gives you AWESOME flexibility Diagrams of bigger systems are shown on pages 7 8 and 9 of this manual SYSTEM UPGRADE 1 This system is an
Download Pdf Manuals
Related Search