Home

EX88HV Inst - Micro Alarm

1. opened e lf this input is receiving 12 volts at the time the alarm is armed the unit will by pass this particular zone until it is removed from 12 volts e lf this input is receiving 12 volts before the alarm is armed the unit will not passively arm self arm until the input is removed from 12 volts the doors are closed INSTALLATION NOTE this trigger input can be programmed for a 60 second delay option designed for vehicles with extended dome light delays See programmable jumper pin options 3 5 2A POWER HARNESS WIRING CONFIGURATION CONT e Connect the alarm s violet wire to the 12 volt positive factory OEM pin switch circuit This circuit will show 12 volts only when a vehicle door is open Note it is necessary to confirm that all vehicle doors are included in the circuit PINK POSITIVE ANTI HI JACK TRIGGER WIRE SEE PAGE 7 amp 8 GREY AUXILIARY 1 OUTPUT This auxiliary channel will provide a negative momentary output when the AUX button is pressed GREY WHITE AUXILIARY 2 OUTPUT This auxiliary channel will provide a momentary negative output as long as the unlock button is pressed BROWN WHITE HORN OUTPUT This wire will provide a 500mA negative output e Connect to vehicle s negative horn relay SOME VEHICLES MAY REQUIRE RELAY 2B 6 PIN DOORLOCK HARNESS WIRING CONFIGURATION FIRST RELAY LOCK PURPLE BLACK Normally Open NO GREEN
2. vehicle s headlights The headlight circuit is a very high amperage circuit and will draw more than the 7 5 Amp maximum load the unit s on board relay can provide If flashing headlights are desired an external relay is required Note halogen lights are not designed for flashing applications and may therefore burn out quickly SPECIAL CASE FLASHING LIGHTS HOOK UP SPECIAL CASE FLASHING LIGHTS HOOK UP VEHICLE HAS SEPARATELY FUSED LEFT amp RIGHT SIDE PARKING LIGHTS EX MERCEDES BMW USING 2 RELAYS 5 USING 2 DIODES 4 CONSTANT 12 VOLTS CONSTANT 12 VOLTS FUSE EACH AT 10 AMPS FUSE EACH AT 10 AMPS STRIPE FACING GROUND GROUND THE LIGHT CIRCUIT ORANGE BLACK DOME LIGHT SUPERVISION PROGRAM 3 ORANGE BLACK DOME LIGHT ILLUMINATION OUTPUT RELAY REQUIRED The alarm s orange black wire will provide a BLACK WHITE WIRE 30 second negative output for illuminating the vehicle s dome light when the alarm is OR DEPENDS ON DOME LIGHT CIRCUIT TYPE disarmed A relay is required see diagram This output will reset if the alarm is armed dis 5 oe TPES armed or if the vehicle s ignition is turned on FUSE AT 3 5AMPS WARNING Do not connect the alarm s orange black wire directly to the dome light circuit or TO DOME LIGHT severe damage will occur to the unit 4 ANTI HIJACK FUNCTIONS CONT e Connection anti hi jack mode can be wired to trigger by pressing a mo m
3. will oc cur to the unit Note if more than one siren is desired or if a high current sounding device is to be used ie mechanical siren air horns etc ADDITIONAL RELAY MUST BE ADDED BLUE NEGATIVE HI JACK ENABLE SEE PAGE 8 9 GREEN NEGATIVE TRIGGER DOOR INPUT The door input is an instant trigger zone for vehicles equipped with a pa type pin switch circuit This input will trigger the alarm if it becomes grounded while the alarm is armed ie a door is opened e lf this input is grounded at the time the alarm is armed the unit will by pass this particular zone until it becomes ungrounded e lf this input is grounded before the alarm is armed the unit will not pas sively arm self arm until the input is ungrounded the doors are closed INSTALLATION NOTE this trigger input can be programmed for a 60 second delay option designed for vehicles with extended dome light delays See programmable jumper pin options 3 connect the green wire to the negative factory oem pin switch circuit This circuit will show negative ground only when a vehicle door is open Note it is necessary to confirm that all vehicle doors are included in the circuit VIOLET POSITIVE TRIGGER DOOR INPUT The door input is an instant trigger zone for vehicles equipped with a positive type pin switch circuit e This input will trigger the alarm if it receives 12 volts while the alarm is armed ie a door is
4. ANTI HI JACK PROGRAMABLE THROUGH POSITIVE TRIGGER WIRE AND IGNITION PIN 5 e Pin 7 in and pin 5 out anti hi jack feature can only be accessed when 12 volts is applied to the pink positive trigger wire while ignition is on e Anti hi jack can be disarmed only by pressing the valet override button while ignition is on CONNECTION Anti hi jack mode can be wired to trigger by pressing a positive momentary switch or positive door trigger wire while the ignition is on 3 JUMPER PIN CONFIGURATION SELECTABLE JUMPER OPTIONS PIN PIN IN DEFAULT 1 Last Door Arming Feature PIN REMOVED Disable Last Door Arming 2 Door Lock w last Door Arming Disable Locking w Door 3 Normal Door Trigger Extended Door Trigger 60 Seconds Arming Delay for Dome Light Ignition Auto Lock Disable ignition Auto Lock Ignition hi Jack Disable Ignition Hi Jack Enable Double Pulse Unlock Enable Hi Jack Enable 2 Step Disarm Normal Unlock Disable Hi Jack Disable 2 Step Disarm O N ODO Oo Ff 9 Parking Light Positive Output DEFAULT Disabled 10 Parking Light Negative Output Disabled NOTE 1 YOU MUST POWER DOWN UNIT AFTER CHANGING ANY OF THE JUMPER PIN SETTINGS OR CHANGES WILL NOT BE REGISTERED NOTE 2 Open case lid to modify JP s 1 8 NOTE 3 Jumper pin 3 controls both passive locking amp 60 sec door trigger delay NOTE FOR JP9 AND JP10 You must select either POSITIVE or NEGATIVE for Parking Light Output DO NOT
5. BARRACUDA EX88HV INSTALLATION MANUAL LOCK SILENT MODE Press and release the Lock and Unlock buttons to activate alarm Silent Mode no siren chirp only parking light will flash Press and release Lock button to activate alarm and lock doors UNLOCK SENSOR DEFEAT Press the Lock button within 3 seconds press the Lock and Unlock buttons for 2 seconds to activate Sensor Defeat Press and release Unlock button to deactivate alarm and unlock doors AUX DEACTIVATE os SENSOR DEFEAT Press and release the AUX button to provide a momen i Press Unlock button to tary output deactivate Sensor Defeat PANIC HI JACK ENABLE Press and hold the Panic Press the Panic button for ees DUtton for 2 seconds to Q RS acond a activate HiJack activate panic mode mode with IGN on NOTE Press Unlock to stop panic mode AUX 2 HI JACK DISABLE Press and hold the Unlock Q Press the Unlock button to button for 2 seconds or longer E deactivate Hi Jack mode with to provide an output for as IGN on long as pressed THIS IS ONLY A GUIDE These instructions are a general guideline of possible applications Specifications may change dependent upon vehicle Always review the vehicle s service manual and wiring diagram when performing an installation Manufacturer does not assume any responsibility for damages to property or persons which may occur due to incorrect applications or product failure
6. BLACK Common COM WHITE BLACK Normally Closed NC SECOND RELAY UNLOCK RED BLACK Looped to PURPLE BLACK Normally Open NO BLUE BLACK Common COM BROWN BLACK Normally Closed NC fused at 15 Amps NOTE 1 e Connect GREEN BLACK wire to Vehicle Lock Wire e Connect BLUE BLACK wire to Vehicle Unlock Wire gt WHITE BLACK gt BROWN BLACK NIC 5 N C COM Z COM N O gt N O gt PURPLE BLACK 8 RED BLACK LOOPED gt GREEN BLACK gt BLUE BLACK DIAGRAM Built In Onboard Relay Configuration 6 2B 6 PIN DOORLOCK HARNESS CONTINUED NOTE 2 e Lock Relay PURPLE BLACK wire is used for both doorlock systems NOTE 3 e For door lock configurations please refer to SAMPLE LOCK AND UNLOCK WIRING CONFIGURATIONS page 6 WHITE BLACK p gt 5 eS WHITE BLACK pB acne fe Bisel lees e GREEN BLACK iy N aad On la GREEN BLACK gt _ __ _ p PURPLE BLACK i gt PURPLE BLACK gt 7 BROWN BLACK gt z E BROWN BLACK on i J BLUE BLACK j O BLue ack j p RED BLACK gt CESP RED BLACK F eS resis WHITE BLACK gt GREEN BLACK gt 2 ae PURPLE BLACK gt _WHITE BLACK gt BROWN BLACK a Le _GREEN BLACK Bo l BLUE BLACK gt PURPLE BLACK po o RED BLACK sy 77 gt BROWN BLACK gt A e ett nine O 3 a BLUE BLACK BLUE BLACK j a Ss iets Electric Motor A Main Li
7. HAVE JUMPER PIN IN BOTH 4 ANTI HIJACK FUNCTIONS This unit has four ways to program the anti hi jack feature Anti hi jack programable through the pin 7 PINK POSITIVE ANTI HI JACK TRIGGER WIRE This alarm is equipped with an anti hijack feature This feature is designed to provide vehicle security in the event That the vehicle is commandeered from the user e f programmed the pink anti hijack trigger input wire will activate a 60 second countdown if 12 volts is applied while the vehicle s ignition is on e Once anti hi jack mode is entered the led begins flashing rapidly amp a 60 second countdown begins During this 60 Second countdown the user can disarm the system two different ways 1 Press button unlock for 2 seconds on the remote control with the ignition on kA OCH 2 Press the valet override button with the vehicle s ignition on e lf the anti hi jack mode is not disarmed within the 60 seconds the alarm will trigger Once triggered anti hi jack mode can only be disarmed by performing an emergency override Press the valet override button with the vehicle s ignition on 8 2A POWER HARNESS WIRING CONFIGURATION CONT BROWN SIREN OUTPUT This wire will provide a 12 volt positive output for powering a siren e Connect alarm brown wire to siren s red wire e Connect siren s black wire to ground WARNING do not ground the alarm s brown wire or severe damage
8. Not responsible for typographical errors Specifications are subject to change without notice REPLACEMENT REMOTE PART NUMBER REMOTE EX88HVCARB Warranty void if not installed by authorized dealer Specification and date are subject to change or withdrawal without notice 2011 Micro Alarm Inc EX88HV Inst 20110511 indd 1 HOW TO CODE LEARN A REMOTE CONTROL ENTERING CODE LEARNING MODE 1 Turn the vehicle s ignition to the ON position 2 Press the valet override button 5 times e The siren will emit a long chirp amp the LED and parking lights will light solid to confirm entry into code learning NOTE If at any time 7 seconds elapse without input the alarm will automatically exit code learning mode CODE LEARNING REMOTE CONTROLA S 1 Once in code learning mode PRESS THE LOCK BUTTON OF EACH REMOTE CONTROL THAT YOU WISH TO PROGRAM 2 Amaximum of 4 remote controls can be programmed 3 The siren will chirp amp parking lights will flash to confirm each time a remote has been learned according to the number of the remote programmed 4 Itis advisable to fill all three of the memory slots 2 JUMPER PIN WIRING CONFIGURATION 3 PIN RED SHOCK SENSOR CONNECTOR z oomo pseu VALET SWITCH PUL RM 7 a a a N A a vU ANOaARWN qj oo U ENABLE IGN DISABLE IGN AUTO LOCK AUTO LOCK GN HI JACK IGN HI JACK ENABLE PURPLE BLACK NO DISABLE NE PULSE GREEN BLACK COM LOCK UNLOCK LOCK UNL
9. OCK SARM o 0 NORMAL DOOR EXTENDED DOOR LED RED CONNECTOR 0 0 7 WHITE BLACK NC D ISABLE TWO STEP ENABLE TWO STEP permo se fow RED BLACK NO NOTE 1 PIN IN DEFAULT NOTE 2 OPEN CASE LID To MopiFY s s BLUE BLACK COM BROWN BLACK NC BROWN WHITE WIRE Horn GRAY WHITE WIRE Aux Output 2 GRAY WIRE Aux Output 1 PINK WIRE HI JACK Enable VIOLET WIRE Door Trigger ORANGE WIRE Starter Disable GREEM WIRE Door Trigger BROWN WIRE Siren BLUE WIRE HI JACK ORANGE BLACK WIRE Dome Light YELLOW WIRE Ignition WHITE WIRE Parking Light BLACK WIRE Ground RED WIRE 12 Volts JUMPER PIN IN DEFAULT JUMPER PIN IN PARKING LIGHT NEGATIVE OUTPUT A O 2 Lu 2 on O A I 9 x aa lt ai REMOTE EX88HVCARB JP10 JP9 LIGHT JUMPER PIN JP9 JP10 REPLACEMENT REMOTE PART NOTE SELECT EITHER OR FOR PARKING ELELEE NOR ODN OO 8 EMERGENCY OVERRIDE In the case that the alarm s remote control is lost or broken the user can perform an emergency override to disarm the alarm EMERGENCY OVERRIDE PROCEDURE ONLY WHEN THE ALARM IS ARMED 1 Turn vehicle s ignition on 2 Press the valet override button 3 The led will stop flashing amp the siren will stop sounding 9 DUAL STAGE SHOCK SENSOR SINGLE ADJUSTMENT This alarm system comes equipped with a shock sen
10. entary switch while the ignition is on connect the pink wire to a momentary switch BLUE NEGATIVE HI JACK ENABLE This alarm is equipped with an anti hijack feature This feature is designed to provide vehicle security in the event that the vehicle is commandeered from the user e The blue anti hijack trigger input wire will activate a 60 second count down when ground is applied while the vehicle s ignition is on e Once anti hi jack mode is entered the led begins flashing rapidly amp a 60 second countdown begins During this 60 Second countdown the user can disarm the system two different ways 1 Press button unlock for 2 seconds on the remote control with the ignition on kA OCH 2 Press the valet override button with the vehicle s ignition on e lf the anti hi jack mode is not disarmed within the 60 seconds the alarm will trigger e Once triggered anti hi jack mode can only be disarmed by performing an emergency override e Press the valet override button with the vehicle s ignition on CONNECTION anti hi jack mode can be wired to trigger by pressing a mo mentary switch while the ignition is on connect the blue wire to a negative momentary switch ANTI HI JACK PROGRAMABLE THROUGH REMOTE AND IGNITION e Pin 7 out press button panic unit goes to anti hi jack mode ignition switch on e Press button panic with ignition switch off unit will go to panic mode
11. nd plug it in VALET MODE Valet is a special mode in which all of the alarm s security functions are dis abled converting the alarm into a deluxe keyless entry system Valet mode allows the user to turn off the security portion of the system while retaining all convenience features Panic amp keyless entry as well as the auxiliary channel will continue to work in the valet mode This is for situations in which it is not convenient for the alarm to be armed ie car wash mechanic etc TO ENTER VALET MODE 1 Turn vehicle s ignition on 2 Press and hold the valet override button for 5 seconds 3 The led will light solid amp the siren will emit a series of chirps to confirm entry into valet mode TO EXIT VALET MODE 1 Turn vehicle s ignition on 2 Press and hold the valet override button for 5 seconds 3 The led will turn off amp the siren will emit a series of chirps to confirm exit from valet mode 10 2A POWER HARNESS WIRING CONFIGURATION RED MAIN POWER CONNECTION e Connect to the 12 volt positive battery terminal fused at 15 amps BLACK GROUND e Connect this wire to chassis ground e t is of upmost importance that the location of this connection be as clean as possible Make sure that the Area is rust and grease free Scrape off any paint or debris so that the Isurface is bright clean metal e lf the ground connection is poor the alarm may act in an erratic manner The alarm may arm and di
12. ne 3 Jp Cwit s D aake WIC D a RED BLACK p OW P y DIAGRAM Sample Lock and Unlock Wiring Configurations
13. nt draw if there is a start attempt while the alarm is armed It will be necessary to locate and cut the vehicle s starter motor wire e This wire will show 12 volts positive only when the vehicle s starter motor is actually crank ing if the starter motor is not cranking this wire will usually rest at ground See diagram wee seis ZS KEY SIDE OF 9 STARTER WIRE STARTER MOTOR WIRE 2A POWER HARNESS WIRING CONFIGURATION CONT she en PARKING LIGHT OUTPUT Connect this wire to the vehicle s 12 volt positive parking light circuit This output will provide a flashing 12 volt positive output to energize the vehicle s parking lights The vehicle s parking light wire will show 12 volts positive only when the light switch is turned to the parking light and headlight positions The vehicle s parking light wire can usually be found at the light switch fuse junction block or in the harness which runs to the rear of the vehicle usually found in the driver s side kick panel For vehicle s with separately fused left amp right side parking light circuits use either 2 diodes 6 10 Amps each or 2 external relays can be used to separate the left side parking lights from the right side parking lights See diagram DO NOT connect this wire to the dimmer switch This could cause damage to the vehicle s circuit DO NOT connect the modules flashing light wire directly to flash the
14. sarm correctly but would otherwise behave very strangely making it seem that the unit is defective One possible symptom is a constant low volume sound coming from the siren Note Do not ground the thin black wire attached to the brain module this is the unit s antenna Connecting this to anything would severely affect the unit s range YELLOW PRIMARY IGNITION POWER This input will provide the alarm with a 12 volt positive when the vehicle engine is running or when the ignition is turned on This connection is necessary for many vital functions such as passive active arming valet mode override programming led amp memory reset auto lock etc e Connect to the vehicle s 12 volt positive primary ignition wire e The vehicle s primary ignition wire will show 12 volts when the ignition key is turned to the On amp start positions e This wire will not drop out during starter motor cranking e This wire will not show 12 positive when the vehicle s ignition key is turned off ORANGE ARMED OUTPUT FOR STARTER KILL RELAY This output will provide a negative output only when the alarm is armed This output can be used to supply ground to one side of a starter kill relay s coil The other side of this relay s coil will require a 12 positive volts supplied by the ignition switch only when the ignition is turned on or when the starter motor is cranking In this manner there will only be a curre
15. sor The first stage is a warning zone which if triggered will emit a series of siren chirps The second stage is an instant trigger zone ADJUSTMENT When adjusting this sensor it is recommended to set the adjustment screw at the half rotation first then adjust the sensitivity NOTE If the sensor zone is triggered 5 times while the alarm is armed the sensor zone will be bypassed This zone will reset when disarming the alarm MOUNTING Correct placement is essential for proper operation The sensor should be mounted to a rigid wire harness under the dash using plastic cable ties or directly to the firewall using double sided tape Do not mount with screws and do not place under the hood this unit is designed for interior use only CONNECTION plug it in 11 5 PANIC FUNCTIONS Panic programable through remote only e Ignition on press button panic unit goes to panic mode e Ignition off unit goes to panic mode 6 LED STATUS INDICATOR teo STATUS Flashing Rapidly Alarm Armed Intrusion Confirmation Hi Jack Countdown Valet Mode CONNECTION mount where desired and plug it in 7 VALET OVERRIDE BUTTON Flashing Repidly Ignition On On Solid The valet override button has three functions 1 To allow the user to place the alarm in the valet mode 2 To perform an emergency override in the case that the remote control is lost or broken 3 To program remote control see page 2 CONNECTION mount where desired a

EX88HV Inst - Micro Alarm

Contents

Download Pdf Manuals

Related Search

Related Contents