Home

LM2700-2226 10348 & up Owners Manual

Contents

1. amal SI ES ole O 1 K SE m Small screw for Cutting height gauge groomer adjustment Always use the cutting height gauge and adjust it so that right and left sides become parallel The bearings may be damaged if it is not used Set the groomer height more than 5mm from the ground If it is used by less than it the groomer axis bearing and gear etc may be damaged 7 6 Loosen the fixing bolts on the right and left sides of the reel cover and adjust the angle of the reel cover When you use the optional grass catcher set the reel cover housing in the most closed position 7 7 It is easily maintainable to turn the 2 and 3 mower unit turn to outside of the main body 1 Lower the mower unit and remove the Retaining pin and then pull out the Lock pin d 2 Turn the mower unit to outside of the main body Adjustment of the reel cover Fixing bolt Reel cover Turning the 2 and 3 mower units 35 3 After turning install the lock pin over the hole to retain the mower in the maintenance position 4 Raise the mower unit
2. B Total Length 300cm 3 Total width 320cm 228cm when travelling 2970m 228cm when travelling a Total height 220cm Roof 204cm Roof bar 150cm Steering wheel Wheelbase 155cm Total weight 1 750kg 1 730kg 2 Two wheel drive 0 22km h o Four wheel drive 0 14km h Front wheel 26 5 x 14 00 12 8 Rear wheel 20 x 12 00 10 Model KubotaV2203 M Vertical type water cooled four cycle diesel Number of cylinders 4 Displacement 2 197L 2 197cm Rating output 33 5kW 45 3PS 2 600rpm euiBu3 Rotation Speed 975 2 800rpm without load 1 Fuel consumption at 2 500 rpm 250g kW h 185g PS h Battery 105D31R recommended EXIDE 27 60 Mowing height 8 45mm 2 Mowing width 277cm 254cm Reel cylinder 9 blade 66cm x 5 reel diameter 16 3cm 9 blade 56cm x 5 reel diameter 16 3cm 1 Maximum engine rpm is set up 2 600 rpm before shipment 2 For 10 mm or less mowing height the optional bed knife is required Handling instructions 1 Inspection before use A Please be sure to check the following matter before putting the A Caution engine into operation 1 1 Cleaning of the radiator and oil cooler Be sure to clean when the dust has adhered to the radiator oil cooler and dustproof net When you operate it in the dusty place please try to clean a little early Oil cooler Radiator Dus
3. lt Operation panel gt 2 Inside the hood on the left side that can be seen from the rear e A ED Valain OOO D I e a E CH xi 1 Et eg 3 oco fs P Er LOAGA N ud G3 hc K4205001840 DU K4205001580 K4205001530 D Attach on the left and right Front right of the frame Rear right of the frame K4205001580 Z uU E x E EEZ a ey ON KE Sch LS EN user AN SA cl od IT STOP aby Ke K4205001600 CSS Bl Y Attach two labels to BY each mower K4209000980 PY YN K4205001540 Low sulfur or ultra low sulfur diesel fuel only 14 _15 Warning label and operation label description Attach the warning labels and operation labels in the locations that are close to dangerous parts and in which the labels can be easily seen If a label is damaged or peels off attach a new label to the machine D e Ad 13 os TM A Ader A fa SLOW g Read the Operator s manual rere Leave the machine after s
4. 5 Return the mower unit to the original state in the reverse procedure after the maintenance Replace all the bearings oil seals for mower unit every year The hydraulics motor housing with the hydraulic motor is filled up with the lubricating grease PYRONOC No CCO Check and supply grease every 200 hours d d Both the reel cutter and bed knife are the cutting tools AA Danger ds When you handle with them be careful of injury 8 Cautions for maintenance 8 3 Maintenance schedule Use the required tools suitable for the purpose of the maintenance Before Every Every Every Every Every 6 Caution 8 1 Cautions for maintenance Maintenange use 50hrs 100hrs 200hrs 500hrs months Inspection of engine oil O e Read this manual carefully and have full knowledge of the Change of engine oil SIE O maintenance procedure operation Stay the machine on a flat clean and dried place Replacement of oil filter Cina O Never lubricate or maintenance when the machine is in motion Cleaning of radiator and oil O Keep hands feet away from drive moving parts cooler For the maintenance of drive moving parts be sure to exercise 9 P m Inspection of coolant O caution lest hands and feet should be caught up a i diea Disengage all the drives
5. Do not carry out in two person operation 7 4 Lapping 1 Inspect whether the newspaper can cleanly cut across the full length of reel 2 Set the bypass valve lever of the hydraulic motor into the Rotation position on the lapping mower unit Set bypass valve lever of the hydraulic motor into Stop position on the mower unit which does not carry out lapping 3 Lower all the mowing unit to the ground then stop the engine Open the hood and reel reverse rotation switch to ON Refer to 3 16 5 Sit on the seat engage the parking brake start the engine and then adjust rotation of engine to low speed Set the reel rotation switch into the ON position and carry out the lapping rotation of the reel blade Refer to 3 15 7 Adjust reel rotation adjusting valve to the desired speed Refer to 3 21 Apply lapping compound with brush to the part where a newspaper was cut Never apply lapping compound to the part where was not cut well Use lapping compound which is a mixture of oil and emery 150 200 at rate of 1 3 to 4 9 Rotate the reel cutter for a while if there is no longer contact sound stop the rotation and then stop the engine 10 Check full length of the reel cutter whether there are the parts that cut off the newspaper well and the parts that don t cut the newspaper Repeat the above steps and at the same time make a slight adjustment on the reel unit there is a un
6. Water temperature gauge When the water temperature gauge rises to near H during the operation it is in the overheating state Stop the engine and carry out the maintenance and repair after making the engine no load and operating for 5 minutes in idling If the water temperature raise above 115 C the warning alarm discontinuous sounds will sound 4 1 Instruments of operation panel x Ki gt x100RPIM gt 10 TACHOMETER 30 GE e Da Hour meter WATER TEMP 26 4 4 Fuel gauge It indicates current fuel level If the fuel gauge approaches E Empty supply fuel diesel immediately The capacity of the fuel tank is approximately 51 Liters A Dan er Don t oversupply the fuel It may cause the fire if the fuel overflow 9 from the fuel tank Use diesel oil only Be sure not to use gasoline e 4 5 Charge lamp The lamp turns on when the ignition switch is in the ON position After the engine starts and the light will turn off if it charges normal When the lamp is turned on during 1 operation stop the engine immediately and Charge Glow RE inspect do maintenance and repair Q 4 eu O Charge lamp 4 6 Thermostat lamp Glow lamp Refer to 3 3 Starting and stopping the engine Thermostat
7. every 10hrs is injected into the skin be sure to have medical treatment by Inspection of grease in the O doctor within 2 to 3 hours hydraulic motor housing Contact condition of the Oo blades on reel cutter Remove adhesion of cutting O grass etc 36 lt Specifications for periodic maintenance gt Engine oil capacity MAX 9 7 LMIN 7 L Higher than the API service classification CD class Including 1 L in reserve tank Coolant capacity Tire pressure standard tire Total capacity 12 L Front tire 150 kPa 1 5kgf cm Rear tire 140 kPa 1 4kgf cm Fuel tank capacity Approximately 51 L Diesel JIS2 type Oil tank capacity Approximately 44 L Use the Shell Tellus 46 equivalent Wear parts lists for the engine hydraulic system For engine Oil filter element PF16414 3243 0 Air filter element PFR1401 4227 0 Fan belt PF17112 9701 0 Fuel filter cartridge PF15221 4317 0 Battery K3600000180 equipped on Mchine originally K3600000250 for replacement LM2700 0535Z0 Throttle wire For hydraulics system Oil pressure filter cartridge K3410000030 Air filter element K3413000040 37 9 Adjustment of the other functions 9 1 Adjustment of the neutral position of piston pump D 1 Jack up the machine and put on a stable stand and float the front and rear wheels 2 Raise the seat upwards 3 Start the engine and run at high speed and
8. 20 Bypass valve It is located on the hydraulic motor of each mower unit The hydraulic motor will become free if the shift lever is shifted to the stop position Rotate position CE Stop position C 3 21 Reel rotation adjusting valve For mower units 1 4 and 25 Bypass valve For mower units 1 4 and 25 It is the valve that adjusts the rotation speed of the reel cutter Loosen the locknut and turn in the knob the rotation speed will become slow Knob Locknut 25 Mower lock lever latch AL el Ve D Hang the mower lock lever when you transfer the machine or store the machine With the mower unit 4 and 5 are raised 3 23 Groomer clutch lever option It is the operating lever that makes the groomer ON or OFF When you do not operate the groomer be sure to shift it to OFF position Mower lock lever 4 Measuring instrument a Tachometer amp hour meter b Water temperature gauge c Fuel level gauge d Pilot lamp Charge lamp Glow lamp Oil pressure lamp Engine oil pressure lamp 4 2 Tachometer amp hour meter Indicate the engine speed and total operating hour Carry out the periodic inspection and maintenance and repair based on the operating hour 4 3
9. belt while the engine is running could result in injury Caution Hot surface Do not touch It can cause burns gt e K4205001530 BIM K4205001540 gt Pinch You can get pinched K4205001580 p x Fuel filler port No 2 diesel fuel only Low sulfur or ultra low sulfur diesel fuel only K4209001000 1 Number Plate model serial No Xkvoeisna co c70 Head Office Toyokawa Aichi Pref 442 8530 Japan 1 26 Miyuki cho year of MADE IN JAPAN manufacture 2 Specification Plate BARONESS Specifications LIT Model Rating output Total weight CE T vorisua CO LTD Features of LM2700 Compared with the conventional machine the work at a quick speed can also be cut finely Moreover since the travelling speed is also quick and the turning radius is small efficient work can be performed Comfortable work can be performed by the introduction of the large displacement engine The introduction of the new oil hydraulics travelling system and the large sized disc brake etc is raising the safety The optimal sheet position is obtained according to the driver s body The maintenance of the bottom mower can be performed easily 16 Specifications Model LM2700 Mower unit type 26in 22in Drive system Four wheel drive
10. do so f noted in the manuals use a counterbalance or wheel balance Never neglect the warnings for hidden hollows or obstacles Watch out for other traffic when crossing or near a road Stop the rotation of the reel cutter when operating on surfaces other than grass When using attachments never direct the discharge at bystanders Never allow anyone near the mower while it is operating Do not operate the mower with damaged guards or with guards not installed properly Do not remove the interlock device and be sure to use it when it is adjusted properly Do not change the engine governor setting or operate the engine at high engine speeds Otherwise an accident resulting in injury or death or a malfunction can occur Before leaving the operator s position Move the mower to a level surface Disconnect the power take off PTO and lower the attachments Place the gearshift into neutral and set the parking brake Reduce the engine speed Stop the engine and remove the key Note After operating with a heavy load let the engine idle for 5 minutes before turning the engine off W Disengage the drive to each attachment except when mowing E Stop the engine disengage the drive to each attachment and remove the key under the following conditions Before refueling Before removing the grass catcher Before adjusting the cutting height except when the adjustment can be made from the operator s seat Bef
11. line and make turns where the grade of the slope is low Remove the battery and pull out the key when long trem storage Remove the battery and pull out the key when not using the machine and keep in storage for a long time Failure to follow this precaution can cause fatal accident 7 After operating the machine and storage E Add oil and refuel when the engine is cold Do not add oil or refuel when the engine is operating or if the engine is hot Failure to follow this precaution can cause the fuel to ignite and cause a fire E Do not open the radiator cap when the radiator is hot When the radiator has overheated do not open the radiator cap Failure to follow this precaution can cause scalding water to shoot out and cause burns Bl Cover the machine with a sheet after it has sufficiently cooled down If covering the machine with a sheet cover it after the muffler and engine have sufficiently cooled down Failure to follow this precaution can cause a fire E Install and remove the battery by following the correct procedure To install the battery connect the positive battery cable first To remove the battery disconnect the negative battery cable first Failure to follow this precaution can cause a short circuit which can cause burns and a fire E Perform inspection and maintenance on a flat and stable place Set lower the mower unit and perform inspection and maintenance on a flat and stable place on whic
12. model number and serial number Safety This machine meets CEN standard EN 836 1997 by affixing the specified label for ride on lawn mowers at the time of production Improper use or maintenance can result in injury or death To prevent an accident be sure to follow the safety precautions described below and always pay attention to the warning symbols The warning symbols are displayed as CAUTION WARNING or DANGER and all symbols describe important safety precautions Failure to thoroughly follow these safety precautions can cause an accident resulting in injury or death Safety management The following instructions are taken from CEN standard EN 836 1997 ISO standard 5395 1990 and ANSI B71 4 2004 Intended uses Use the mower for the purpose it is intended for that is cutting grass on lawns Any other use could be dangerous or damage the equipment 1 Training Read the Operator s manual and other training material carefully Be familiar with the controls and safety indications and learn how to stop the mower in an emergency If the operator cannot understand the manual it is the owner s responsibility to thoroughly explain the contents of this Operator s manual Never allow children to operate or service the mower Never allow adults that are unfamiliar with the instructions to operate or service the mower Follow the age limit specified by your country or local government Never operate the machine while pe
13. operate each control and release c Mi red SES HSH QO pressure Replacement of air filter O Use correct appropriate parts in good condition element Repair or replace worn or damaged parts immediately Inspection of fan belt O Do not modify any mechanical equipments parts Use Baroness Inspection of battery O genuine parts required for maintenance for safety electrolyte n Clean up grass and debris oil grease or fuel spillage Replacement of fuel filter O Q Make sure to disconnect the negative battery cable before maintaining the electric circuit Inspection of tires O G f When you maintain with the machine raised carry out the safe E Y d support securely Inspection of fuel O t 1 Please dispose in accordance with the local law about disposal Inspection of hydraulic oil O e Ir amp of waste oil and unnecessary replacement parts Replacement of hydraulic oil Gees O 8 2 Prevention of the damage caused by high p H Initial pressure oil Replacement of oil filter Oa O When high pressure oil is injected to the skin get seriously S Inspection of brake O naen 8 Oil leakage of each part O n Eliminate the pressure before removing the high pressure line Q EN hose and coupling Masi of Se e Check all the joint fastenings before operating the machine amageon wen pst L Grease up main unit and O tbartiaty W Use the paper or cardboard for the test of oil leak If hydraulic oil mower Refer to 7 1
14. pedal 1 place D 4 lift arm 2 places D Pump idle lever 1 place 4 mower joint fitting 1 place Pump neutral lever 1 place 5 lift arm 2 places Lift arm parts Es 5 mower joint fitting 1 place 1 lift arm 2 places Refer to the following page for the grease up points of each part 29 Grease up positions LN 5 REELM mes ness uwen Se cA EI ELNONERS Mower unit 2 Mower unit 4 D Mower unit 1 Mower unit 5 6 5 Replacement of fuses 1 Fuse box Fusible link Fuse box The spare fuse and the replacement tool d are attached in the fuse box d P Replace with the fuses of the lala TN requirement rated capacity 9 9 The fuses are mini fuse for automobiles LL l P 2 Fusible link CC The fuse rated capacity of the fusible link is 50A S f Y T
15. the throttle lever is lowering to the bottom LOW the engine speed becomes low Throttle lever 24 3 18 Mower unit raise lower lever It is the shifter lever that raises or lowers the mower unit If the shifter lever is moved to the UP position the mower unit will go up and if it is moved to the DOWN position the mower unit will descend At the time of the mowing move the shift lever to the DOWN position If it is shifted to the neutral position the cylinder is fixed and it cannot respond to the undulation Caution Caution UM 3 19 Differential lock switch It is located in the right side on the steering column It is the switch that operates the differential lock of the both front wheels If the switch is moved to the upper or lower position the front wheel will be in the differential lock state If the switch is released the switch will return to the neutral position and the differential lock will be canceled be damaged Neutral position DOWN tma Operalion Mower unit raise lower lever Inspect the area where the machine will be used Differential lock ON Canceled OFF N Differential lock ON ir uer Differential lock switch Never perform the differential lock operation when it s not required There is a possibility that the hydraulic equipment may 3
16. the truck When the machine is loading onto a truck it move forward when the machine is unloading it move backward Failure to follow this precaution can cause you to loose your balance and cause an accident such as causing the machine to fall or overturn Securely fasten the machine to the truck with a rope When loading the machine onto a truck and moving it set the parking brake and fasten the machine to the truck with a rope that has sufficient strength Failure to follow this precaution can cause the machine to fall from the deck of the truck and cause an accident 5 When moving and taking the machine on or off a field m d L E Do not operate the machine on public roads This machine is not authorized as a special motorized vehicle Do not operate it on public roads Failure to follow this precaution is subject to punishment for violating the traffic laws Check your surroundings for safety and slowly accelerate Start the engine after checking your surroundings for safety Accelerate slowly do not start quickly Failure to follow this precaution can cause a personal injury Take precaution with the shoulder of the road when moving On roads with ditches or on roads where both sides are inclined take sufficient precaution with the shoulder of the road Failure to follow the precaution can cause the machine to fall Do not start stop or turn suddenly or operate at excessive speeds Start and stop slo
17. to avoid humidity Inspect all bolts nuts and screws tightened If loose or missing tighten or repair them Repair or replace damaged parts and paint peelings Store the machine in the place where is dry and prevent exposure to rain Remove the battery and ignition key from the mower If you keep the battery installed in the machine disconnect the ground battery cable negative side When storing the machine lower the cutting units In case to store the machine with raising the outermost 4 amp 5 mowers be sure to latch them 38 11 Scrap the Machine When you scrap the machine obeying the domestic law and regulation For example waste oil rubber goods anti freeze battery wire etc EC Declaration of Conformity We Manufacture s Name Kyoeisha Co Ltd Manufacture s Address 1 26 Miyuki cho Toyokawa Aichi pref 442 8530 Japan declare that Product Ride on Lawnmower Make BARONESS Type LM2700 Starting Serial No 10348 compiler of the technical file Name Kyoeisha U K Ltd Address Unit 5 Hatch Industrial Park Grewell Road Basingstke Hampshire RG24 7NG the United Kingdom in accordance with the following Directives 2006 42 EC The Machinery Directive and its amending directives has been designed and manufactured using the following specifications I8012100 1 2003 ISO12100 2 2003 EN836 1997 1305395 1990 References of other Community Directives applied 2000 14 EC 2
18. which is deadly poison and causes severe burns Never smoke near the battery and keep sparks and flames away Eb from it gd ea 4 Sd Gas When removing the battery remove the negative cable first and positive cable last Install the battery assemble the positive cable first and negative cable last When you connect the battery cables connect the positive and negative side correctly When you mistake the battery and the electrical equipment may be damaged The red color cable is the positive side If a dry cloth is used to clean the battery the static electricity may occur and there is danger of fire or explosion Disconnect the rubber catch in right and left and pull up the engine hood upwards until the wire stretches to the limit When you close the engine hood lower it slowly 6 7 Opening and closing the engine hood Rubber catch Lo Die When you close the engine hood be careful not to pinch your Caution Mid d S St d Raise the tilt steering column to the upper position first and then move the seat to the rear end position Pull up the lever behind the seat to release the lock and then raise the seat and open the undercover To close the undercover lower it slowly 6 8 Opening and closing the seat undercover Do not open the engine hood at the windy place z When you close th
19. 004 108 EC Place Japan Signature Ga Daher Date November 4 2010 Name Masahisa Nakazawa Position Quality Dept Manager Manufacturer s Declaration of Conformity for Product Identification Product Make Type Version s Starting Serial No Measured Sound Power Level Guaranteed Sound Power Level Manufacturer Name Address Technical Documentation Keeper s Name Keeper s Address Conformity Assessment Procedure Involved Notified Body Name Address Technical Construction File Date Technical Construction File No Test Laboratory Certificate Report No Means of conformity Ride on lawnmower BARONESS LM2700 Not Applicable 10348 LwA 99 84 dB LwA 103 dB Kyoeisha Co Ltd 1 26 Miyuki cho Toyokawa Aichi pref Japan Kyoeisha Co Ltd 1 26 Miyuki cho Toyokawa Aichi pref Japan Internal Control of Production with Assessment of Technical Documentation and Periodical Checking Annex VI of 2000 14 EC 2005 88 EC SNCH 11 Route de Sandweiler 5230 Sandweiler Luxembourg May 7 2009 TG2700 01 TUV Rheinland Luxemburg GmbH 2a Kalchesbruck L 1852 Luxembourg SNCH 2000 14 2005 88 1355 01 T02700 01 The product is in conformity with the Directive relating to the noise emission in the environment by equipment for use outdoors 2000 14 EC 2005 88 EOC in accordance with Article 12 of the Directive References of other Community Directives applied Signa
20. 10 C 2096 Up to 15 C 30 Up to 20 C 35 Up to 25 C 40 The radiator coolant capacity of this machine is about 12L including the reserve tank Put the engine on the level surface and check the level of the oil by the dipstick It will be the proper quantity if the oil level is between the upper and lower limit when the dipstick is fully inserted If the oil level is low add the engine oil and if the oil is dirty exchange the oil Perform the oil level inspection when the engine is suspended and after 10 to 20 minutes or more past Please keep in mind that it becomes engine failure and cause of accident if the engine oil added too much Perform refilling of the engine oil from the oil filler It takes some time for the added engine oil to fall in oil pan Inspect the oil level again in 10 to 20 minutes after adding the engine oil Never mix different kind of engine oil Use the engine oil higher than the API service classification CD class and SAE viscosity suited to the application environment temperature The engine oil capacity is approximately 9 7L 1 3 Inspection and refilling of engine oil LO oh Upper limit M limit 18 1 4 Inspection of the hydraulic oil Level the engine and always check whether the hydraulic oil is contained to the center of the oil level gauge When refilling the hydraulic oil use the Shell Tellus 46 or e
21. 4kgf cm 1 8 Supply of Fuel Aen Stay the machine on the level Fuel guage approaches E Empty supply fuel diesel immediately Over supply of the fuel is possible to cause the overflow of fuel from the fuel cap when operating the machine on the slope Use the low sulfur or ultra low sulfur diesel fuel JIS No 2 diesel Capacity of Fuel tank is about 512 19 Be sure to keep the following precaution because the fuel is highly flammable Put any naked flame and cigarette off Keep fire away when suppling the fuel Before suppling the fuel stop the engine and cool it down enough To prevent a fire keep the machine clean and free of dust grease and oil Clean up any spilled fuel Don t oversupply the fuel It may cause the fire if the fuel overflow from the fuel tank Use diesel oil only Be sure not to use gasoline Don t supply gasoline 2 Fastening of each portion Many parts are fastening by bolts Bolts and nuts may be loosened some time after initial operation Be sure to tighten them by the specified torque Appropriate tightening torque kgf cm Nominal Normal bolt Heat treated bolt diameter Hardness classification 4 8 Hardness classification 10 9 M6 7 9 14 18 71 38 91 77 142 76 183 55 M8 14 19 28 38 142 76 193 74 285 52 387 49 M10 29 38 58 76 295 71 387 49 591 43 774 97 M12 52 67 104 134
22. 530 24 683 20 1 060 49 1 366 40 M14 70 94 140 188 713 79 958 52 1 427 58 1 917 04 M16 88 112 210 260 897 34 1 142 06 2 141 37 2 651 22 M18 116 144 280 340 1 182 85 1 468 37 2 855 16 3 466 98 M20 147 183 370 450 1 498 96 1 866 05 3 772 89 4 588 65 3 Operation method of each part Check whether the operation state of each part is good and the brake disc tires steering and mower do not have abnormalities in particular before operating the engine In any cases operate the engine by the speed that can carry out the urgency stop Locate and remove all debris in the operating area before using equipment About the mechanical operation 3 1 Before starting engine 3 2 Inspect the area where the equipment will be used Inspect whether there are no damages and the cover guard are securely fastened in place Never operate the engine without proper ventilation Starting and stopping the engine P A Starting procedure 3 3 1 Sit on the seat and adjust seat arrangement for safety 2 Hold brake pedal down pull parking brake lever up until it engages 3 Make the reel rotary switch into the OFF position Pull the throttle lever a little to the upward 5 When the ignition key is turned to the GLOW position the thermostat lamp glow lamp will turn on Be 6 Fully turn the ignition key to rightward promptly w
23. 8mm Set the bed knife angle as the basis of 5 degrees and change it depending on the situation 2 Adjust the height of the rear roller 1 As shown in the figure apply the screw a and b on the cutting height gauge to the bed knife and adjust the rear roller Decide the position of the rear roller on the basis of the bed knife angle 2 Loosen the cutting height adjusting nut first and then adjust the rear roller according to the cutting height gauge 3 At this time to avoid incorrect adjustment do not touch the Front Roller on cutting height gauge surface 4 Tighten the cutting height adjusting nut securely after completing the setting 3 Adjust the height of the front roller 1 Loosen the cutting height adjusting nut for the front roller first and lower the front roller down to the cutting height gauge 2 Tighten the cutting height adjusting nut securely after completing the setting 4 Repeat steps 2 2 3 4 and 3 1 2 on opposite end Complete adjustment to one end before adjusting opposite end d Front roller Cutting height gauge Reel cutter Cutting height adjusting nut Rear roller Front roller Cutting height adjusting nut Cutting height gauge 33 7 3 Adjusting the blades Proper reel to bedknife adjustment is c
24. Front 5 reel cire einig AS Fairway mower M2700 MOWER Operator s manual Ver 1 0 LM2700 22 26 SN10348 and onwards RARONESC engine before using the machine Original Instructions Required reading Read this manual and the owner s manual for the URED UNS Uh NR car cet c sae dace a cealvaeat ce data due taneadatocat ii a Ea 3 1 3 Inspection and refilling of engine oil 18 Te Wr UNI EE 4 1 4 Inspection oF the hydraulleoll 18 1 5 Cleaning of the air deaner trar ttetnrrtnernrtnnnnnennr nnen 18 EE deu EE 4 l 1 6 Inspection of the engine and its surroundings ssessss 19 3 Pr cautions during Opere EE 5 1 7 4 Mairitenanee Ee cutus rado Reuter tat He pk Eds utor mns 6 1 8 ning To use the Baroness mower sote 6 2 Fastening of each portion 19 3 Operation method of each part 20 Warnings Tor Safely EE 6 3 4 caen About the mechanical Dee 20 Be sure to observe for safe operation 7 3 2 GiWaming Before starting engine 20 3 3 Starting and stopping the engine essssees 20 3 4 About the safety device entente 20 3 5 Cautions on fuel bhandlinmg 21 g Inspection and maintenance before and after 3 6 A Caution Cautions when leaving the machine ssssssss 21 operating Ne El E 8 3 7 A caution Parking Drake ccsecccsssesssssesssssesessecscssse
25. NM a A 5A Timer B 5A Glow lamp Tachometer fuel gauge water temperature gauge charge C 5A lamp oil pressure engine oil pressure lamp Water temperature warning alarm Hydraulic oil warning alarm D 15A Relay box 1 E 15A Relay box 2 differential lock F G 5A Timer H 5A Alternator l 5A Fuel pump cooling fan valve safety relay stop solenoid J 5A Relay starter K 5A Spare fuse L 5A M 15A N 15A O Fuse replacement tool 30 6 6 Inspection of battery LL The machine exported from Japan mounts the battery of refillable type FX105D31R Inspect and maintenance the battery periodically Check the electrolyte level between UPPER LEVEL maximum level line and LOWER LEVEL minimum level line When the electrolyte level is falling below to half between UPPER LEVEL and LOWER LEVEL add the refining water to UPPER LEVEL immediately The replacement battery EXIDE 27 60 Baroness recommends to use is maintenance free It may cause injury and accident to refill water in force Be sure not to maintenance it Refer to the Battery s instruction manual UPPER LEVEL LOWER LEVEL Do not drink electrolyte and avoid contact with skin eyes or A Danger T Y clothing Wear protective glasses and protective clothes Charging battery battery generate explosive hydrogen gas as battery electrolyte contains sulfuric acid
26. achine Failure to follow this precaution can cause a personal injury when the operating machine is lowered Before operating remove obstacles in the field such as rocks etc Failure to follow this precaution can cause an accident or injury or the machine to malfunction Do not start stop or turn suddenly or operate at excessive speeds Start and stop slowly When turning sufficiently reduce your speed Failure to follow this precaution can cause the machine to overturn or fall causing damage to the machine Operate or work on a slope with extreme care The balance of the machine worsens on slopes and bumps Be sure to decrease your speed sufficiently and operate and work slowly Failure to follow this precaution can cause the machine to overturn or fall causing damage to the machine Be sure to turn the engine off when inspecting the mower When a malfunction of the reel cutter occurs such as jamming the grass or rocks be sure to turn the engine off to inspect and make adjustments failure to follow this precaution can cause you to get caught up in the machine Keep away from children Keep away from children and do not operate the machine near them Failure to follow this precaution can cause a personal injury Inspect and perform maintenance immediately if unusual vibration occurs If unusual vibration occurs stop the engine immediately then inspect the cause and repair it if necessary Failure to follow th
27. aintenance ee cee eceeeee sees seeeeeeteseeeeneeeees 36 8 2 A Prevention of the damage caused by high pressure oil 36 8 3 Maintenance schedule nenne 36 For engineer ertet o UR rd la a teda ase nu 37 For hydraulics system sssssssssseeeeeeennen m enemies 37 9 Adjustment of the other functions ssssssee me 37 9 1 Adjustment of the neutral position of piston pump 37 9 2 Traction when the machine is unable to travel 37 10 Long term ET E 38 11 Scrap the Machine 38 California Proposition 65 WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Introduction Thank you for purchasing the Baroness LM2700 front 5 reel fairway mower This operators manual describes the correct methods for handling adjusting and checking the machine for those who do the mowing operation of a golf course Be sure to read this manual and make sure that you understand its contents thoroughly before using the machine Our machines have been tested and inspected thoroughly before shipment from the factory However whether the machine can display its original performance depends on the handling method as well as daily checks adjustments and lubrication before and after operation Keep the machine well maintained to expect safe operation and excellent perfo
28. an cause you to get caught up in the machine or a personal injury Let overheated parts sufficiently cool down before inspection and maintenance Let the parts that overheat such as the muffler and engine to sufficiently cool down before checking or performing maintenance Failure to follow this precaution can cause burns Inspect the rotation speed of engine at the dealer of Baroness to make sure the safety and accuracy of engine Please consult with the dealer of Baroness when the large scale repair or maintenance get necessary Be sure to use the genuine parts and accessory in order to use the machine in safe and with best performance Pay attention that it is possible not to warrant the products when using part and accessory of third party Don t use the machine when modify it without previous notice to Baroness Sound Pressure Level This machine was confirmed to have a continuous weightened sound pressure level of 84 dB A at a position of operators as the result of measuring identical machines based on the procedure specified in directive EC standard 2006 42 EC and its amendments Sound Power Level This machine was confirmed to have a sound power level of 98 dBA Ipw as the result of measuring identical machines based on the procedure specified in directive EC standard 2000 14 EC 2 B Vibration Level Hand arm vibration This machine was confirmed to have a maximum vibration level on hands and arms of 3 81m s as t
29. ation and by the sloping ground e Caution be sure to choose the four wheel drive Operate the machine in consideration of the state of the roads and the ground such as the slant and the undulation To prevent the damage of hydraulic equipments be sure to stop the machine and flip a switch dep Be SLOW 3 15j Reel rotation switch Mowing It is swing type switch with ON and OFF for the reel rotation To mow press switch to ON position and Switch to OFF position to disable mowers When operator leaves the seat engine will stop Reel rotation switch When the mower unit is in the UP position the reels do not Caution Werer P Inspect the area where the machine will be used ag 4 d 3 16 It is swing type switch that exchange the rotation direction of the reel To rotate the reels inverse backlapping press the switch to the on position Engine does not stop even though the operator leaves the seat Reel reverse rotation switch rotate Reel forward reverse rotation switch J c Reverse Forward on d TS When not operating the reel rotation switch the reels do not Never switch on and off while the reel rotating otherwise hydraulic equipment may be damaged 3 17 Throttle lever If the throttle lever is pulling up to the top HIGH the engine speed becomes high and if
30. cified maximum air pressure Failure to follow this precaution can cause the tires to explode and cause an injury Take sufficient precaution with exhaust gas Do not start the engine in an enclosed area Start the engine outdoors with sufficient air circulation If you have to start the engine indoors make sure there is sufficient ventilation Failure to follow this precaution can cause you to be poisoned by the exhaust gas which can result in death Be sure to check the parking brake lever Check that the brake operation is not faulty and that the parking brake lever is not remarkably loose nor does it have remarkable play Failure to follow this precaution can cause an accident Remove debris from the muffler and engine Check that there is no grass debris or fuel around the muffler and engine or on the brakes every day before operating the machine Failure to follow this precaution can cause a fire Turn the engine off while inspection and maintenance Be sure to turn the engine off while inspection servicing repairing or cleaning the machine Failure to follow this precaution can cause you to be pinned under the machine or a personal injury Let overheated parts sufficiently cool down before inspection and maintenance Let the parts that overheat such as the muffler and engine to sufficiently cool down before inspection and maintenance Failure to follow this precaution can cause burns E Perform inspect and maint
31. d the working Caution condition The machine detects the position of the reel unit and decides ON or OFF the reel rotation Keep in mind that the reel rotation may not stop if the mower unit is not fully raised by operating the mower unit raise lower lever N wo EN Wu o 6 Maintenance of the main unit 6 1 Change of engine oil L Refer to the engine s instruction manual for handling of the engine 1 Change the oil after the first 50 hours operation and change it for every 100 d hours operation from the next 2 Remove drain plug on the oil pan If it ES carries out while the engine is warm the NEE H H a oil can be drained completely z 7 NZ Drain plug Drain plug Use the engine oil that has SAE viscosity higher than the API A Caution service classification CD class S The engine oil is high temperature immediately after the operation Change it after waiting for a while so that you may not aliti be burned when removing the drain plug pes en 6 2 Change of hydraulic oil 1 Change the hydraulic oil after the first 100 hour operation and change it in the shorter period between the one year and 500 hours operation from the next 2 Always replace the hydraulic filter when changing oil 3 Remove the drain plug on the bottom of EC the hydraulic oi
32. e engine is operating or if the engine is hot Failure to follow this precaution can cause the fuel to ignite and cause a fire B Fire is strictly prohibited when refueling Do not smoke or use open flames when refueling failure to follow this precaution can cause the fuel to ignite and cause a fire E Take precaution with fuel leaks Be sure to check the fuel pipe and see if it is damaged and fuel leaks failure to follow this precaution can cause fuel to ignite and cause a fire Bl Close the fuel cap and clean up any spilt fuel After refueling be sure to securely close the fuel cap and thoroughly clean up any spilt fuel Failure to follow this precaution can cause a fire Bi Fire is strictly prohibited when checking the battery Fire is strictly prohibited when checking or charging the battery Failure to follow this precaution can cause the battery to ignite and explode which can cause burns Bl Do not let electrolyte get on your skin Do not let electrolyte get on your skin or on your clothes If it gets on your skin or clothes immediately wash the affected area with water Failure to follow this precaution can cause burns or damage to your clothes E Install and remove the battery by following the correct procedure To install the battery connect the positive battery cable first To remove the battery disconnect the negative battery cable first Failure to follow this precaution can cause a short ci
33. e if the operator leaves the seat without engaging the parking brake 3 5 Cautions on fuel handling Danger Itis highly flammable Do not smoke when handling fuel Never fill the fuel tank indoors and while engine is running or the engine is hot In order to prevent the fire always keep the engine clean and be sure to remove deposition of grass grease and oil Clean spilled fuel immediately 3 6 Cautions when leaving the machine Opec Stop the machine in level place and engage the parking brake sn Caution 2 Make the reel rotary switch into the STOP position and lower the mower unit to the ground 3 Stop the engine 4 Remove the ignition key 5 When effectiveness of the brake is not good park the machine using wheel stoppers Caution onrak on heshapes J 3 7 Parking brake P A The parking brake is on the center housing left side Hold the brake pedal down and pull the parking brake lever up for engaging the parking brake Press the brake pedal down again for releasing the parking brake 3 8 Forward Backward pedal Two pedals system is adopted To move forward press the inside pedal down To move backward press the outside pedal down If the pedal is returned the machine will stop automatically Parking brake lever Si e E Brake pedal Brake pedal Be sure to run after releasing the parki
34. e undercover be careful not to pinch your Caution E y fe 3 6 9 Adjustment of brake Carry out the clearance adjustment if the clearance between the brake disk and brake pad becomes large and effectiveness of the brake disc worsens Loosen the lock nut and tighten the adjusting nut the clearance will become small If adjusted to the proper clearance tighten the lock nut securely The fine adjustment can be performed with the wire Be sure to adjust so that effectiveness of the brake disc on either side becomes the same Brake disk Wire Lock nut Adjusting nut lt will generate heat if the clearance is too small and it becomes Danger the cause of the fire If effectiveness of the brake disc on either side is different it may lead to an unexpected accident 6 10 Air bleeding from fuel Since this machine has equipped the automatic air bleeder the air bleeding operation is unnecessary Always use the air bleeding valve with the fully open position If it is used in the closed position it will become the cause of the engine stop 1 SC Ts Pp Q PH 3 g ges 7 Maintenance of the mower 7 1 Greasing Carry out the greasing up periodically to each part grease fitting The parts greasing up every 10 hours is using the needle bearing Be careful of the lubrication interval Ca
35. en lending the machine to others Thoroughly explain the operating procedures and instruct them to read the Operator s manual before use Failure to follow this precaution can cause an accident resulting in severe injury or death or damage to the machine 2 Before operating the machine E Do not carry passengers The riding capacity of this machine is one person Do not carry passengers Failure to follow this precaution can cause an unexpected accident E When starting the engine be sure to be seated in the operator s seat and check your surroundings for safety When starting the engine be sure to be seated in the operator s seat check the position of the seat and check your surroundings for safety failure to follow this precaution can cause an unexpected accident E Do not drive or operate the machine or work at night Do not drive or operate the machine or work at night or in poor visible condition Failure to follow this precaution can cause an unexpected accident Bi Warm the engine up when it is cold When the engine is cold be sure to warm it up Failure to follow this precaution may not allow the machine to sufficiently demonstrate its performance capability AA C au t i on ail E Take precaution with a hot muffler exhaust pipe Do not touch the muffler exhaust pipe while operating the machine or just after the engine is turned off since it will be hot failure to follow this precaution can cause burn
36. enance on a flat and stable place Perform inspect and maintenance on a flat and stable place with no traffic risk using tire chocks on which the machine will not overturn or move Failure to follow this precaution can cause the machine to overturn and cause an unexpected accident Be sure to install the covers Be sure to install any covers that were removed while inspection and maintenance Failure to follow this precaution can cause you to get caught up in the machine or a personal injury Correctly use the proper tools for the job Properly manage and correctly use the proper tools necessary for inspection and maintenance Failure to follow this precaution can cause an accident due to improper maintenance 4 When transporting the machine Bl Do not operate quick start and stop on a running board Take sufficient precaution when operating on slopes or running boards Failure to follow this precaution can cause an accident such as fall or overturn Use a running board with sufficient strength length and width When loading or unloading the machine onto a truck be sure to turn the engine of the truck off on a flat surface that is safe from traffic set the parking brake to avoid moving and chock the wheels The running board should be non skid and bear sufficient strength length and width Failure to follow these precautions can cause an accident such as fall or overturn Bl When the machine is loading unloading on
37. etting the parking brake turning the engine off and removing the engine key Flying objects Excluding the operator keep a safe distance away from the machine Cutting hands or feet Do not put near moving parts Overturning Do not operate the machine on a slop of 15 degrees or more due to danger of overturning When going down a slope fasten the seat belt and operate the machine at slow speeds 2 H gj Read the Operator s manual e Engine starting up procedure 1 LL please read the Operator s manual D Take a seat e Le 2 N 3 8 o 2 Tum the key to the Glow position and x LA RECH 2 Q ff wait until the thermostat lamp goes out Gg Tum to the START position 95 1 2 o8 3 Be Step on the brake pedal and release 4T ZS A C9 the parking braking UP e Engine stop procedure K4205001840 Turn off the knife rotation switch and raise the mower 2 Apply parking brake system 3 Tum the key to the STOP position and remove it Cutting hands or feet If you do not stop rotating the mower and the engine is not turned off there is a risk that you may get injured AMAA O STOP K4205001600 4 eck High pressure oil symbol Read the Operators manual 46 K4209000980 Cutting of Hand Placing your hand near the fan and the
38. h the machine will not overturn or move Failure to follow this precaution can cause the machine to overturn and cause an unexpected accident Bl Remove debris from the muffler and engine Check that there is no grass debris or fuel around the muffler and engine and on the brakes every day before operating the machine failure to follow this precaution can cause the fuel to ignite and cause a fire E Be sure to inspect the electrical components and wires Inspect if the electrical cables are touching other parts if the cover is disconnected or if the connector is loose every day before operating the machine Failure to follow this precaution can cause a fire Bi Take precaution with high pressure hydraulic oil Always check if the fittings and hoses are loose or damaged When disconnecting the joints and hoses release the pressure in the hydraulic circuit Failure to follow this precaution can cause the high pressure hydraulic oil to break through your skin and cause an injury al Ai a QU me 29 gitt Caution Caution Bi Turn the engine off while inspecting and maintenance Be sure to turn the engine off while checking servicing repairing or cleaning the machine Failure to follow this precaution can cause you to be pinned under the machine or a personal injury Be sure to install the covers Be sure to install any covers that were removed during inspection and maintenance Failure to follow this precaution c
39. handle 3 Check and adjust with the scale 4 50 130kgf Angle setting of the armrest can be performed by turning the knob 5 The height of the seat can adjust to the three steps by lifting the whole seat d Reel forward reverse rotation switch DOWN i 1 Y Operation c Reel rotary switch 22 When it is set to UP the position of mower unit 4 amp 5 can be changed Press switch to the Travelling position 4 amp 5 mower units raise to top Press switch to the Operating position 4 amp 5 mower units raise up to middle Select Travelling 3 13 Travelling Mowing changeover switch Ch Travalling e p Mowing C N Travelling Mowing changeover switch Select Mowing Is AR EN L 5 It is the switch that chooses two wheeldrive front wheel travelling or four wheel drive travelling If it moves to the 2WD position it will become the two wheeldrive and if it moves to the 4WD position it will become the four wheel drive 3 14 2WD 4WD changeover switch 2WD 4WD changeover switch jd When you move under the oper
40. he result of measuring identical machines based on the procedure specified in ISO5349 Whole Body This machine was confirmed to have a maximum vibration level on whole body of 0 99m s as the result of measuring identical machines based on the procedure specified in ISO2631 13 Names of various sections EEEE H Throttle lever Tilt lever Hood C Mower unit raise lower lever 74 Een panel Brake pedal o Fuel filler hole Forward pedal FAIRWAY 5 BED ess SE pou See I L Light c CNN Parking brake lever d I eu Er A 7 J E A E dp 5 o d ug dd d PE qt Eras p T SS f oN ii f A p 27 d a 2 Number plate l Uke PE H Mower unit 2 M nil gt 2 Specification plate L J Mower unit 4 CZE M Mower unit 1 JOP of Mower unit 3 Mower unit 5 Warning label and operation label attachment locations
41. hen the thermostat lamp glow lamp turns off the starter will operate and the engine will start Release it as soon as engine starts Y Thermostat lamp Glow lamp i 7 7 7 Ensure that the charge lamp and the Charge ne SE engine oil pressure lamp turns off O 4 Py 0 O When they do not turn off stop the engine and perform the inspection and repair Do not step on the shift pedal Safety device prevents the engine from starting Do not touch the V Belt the Pulley etc during the engine rotation Operation of the starter is a maximum of 15 seconds When the engine still does not start to prevent battery wastage restart should be made 30 to 60 seconds after Stopping procedure 1 Hold the brake pedal down pull the parking brake lever up until it engages 2 Make the reel rotary switch into the OFF position 3 Return the throttle lever to the LOW position 4 The engine will stop when the ignition key turns to STOP position 3 4 About the safety device This machine is equipped with the Safety device to starting stopping of the engine as interlock system Safety device on this machine prevents the engine from starting unless a Sit on the seat b Parking brake is engaged c The reel rotation switch is STOP position d The shift pedal is in Neutral position Do not step on the shift pedal The interlock system will stop the engin
42. iform clearance along full length of the cutting edges 11 Finally apply lapping compound to full length on the edge of each blabe of the reel cutter and carry out final lapping 12 When finished carefully and thoroughly clean off the remaining lapping compound 13 Return the reel rotation adjusting valve to the original position Both the reel cylinder and bed knife are the cutting tools When e A Danger you handle with them be careful of injury When you try cutting the newspaper be careful not to pinch your fingertip which turns the reel cutter Before doing this work be sure to apply the parking brake firmly Do not carry out in two person operation When you wash the abrasive be careful not to pour water to the Electrical equipment and the switches If they become wet it may cause unexpected accident A Caution J _34 7 5 Adjustment of the groomer option 1 Set the small adjusting screw for groomer adjustment on the cutting height gauge to the specified height Refer to 7 2 Loosen the rod receiver nut and lower the whole groomer unit to the bottom of the long hole 3 Tighten the rod receiver nut and adjust the height of the groomer with the adjusting nut for the groomer When you do not use the groomer raise the whole groomer unit to the top of the long hole Rod receiver Groomer adjusting nut T
43. is precaution can cause an accident or injury or the machine to malfunction Keep bystanders away from grass discharge area Grass dust sand and rocks will fly out In addition be sure to install the reel cover Failure to follow this precaution can cause a personal injury Do not look aside Do not operate or travel with no hands Failure to follow this precaution can cause a personal injury or material damage When leave from the machine stay machine at level place and stop engine Stay the machine at flat and stable place then turn the engine off set the parking brake chock the wheel lower the mower unit and remove key from ignition switch Failure to follow this precaution can cause the machine to move spontaneously and cause an accident Do not carry passengers The riding capacity of this machine is one person Do not carry passengers Failure to follow this precaution can cause an unexpected accident Precautions for operating on slopes When operating on a slope the ground will not be even and there may be bumps and rocks which can cause the machine to incline suddenly Therefore never operate the machine on a slope of 15 degrees or more or in areas in which there is danger of it overturning or slipping Remove holes rocks or tree roots and other illegally thrown objects and check that these items do not exist before operating the machine on a slope When operating the machine on a slope work along the contour
44. l tank and drain the hydraulic oil Hydraulic fluid tank Filter Drain plug 4 Drain and replace the hydraulic oil if you notice the presence of water or foam in the oil emulsifying or contamination lack of transparency 5 Use the Shell Tellus 46 or equivalent products for the hydraulic oil The capacity of the hydraulic oil tank is approximately 44Liters The hydraulic oil is high temperature immediately after the operation Change it after waiting for a while so that you may not be burned when removing the drain plug Zeg Do not overfill aibi 3 ll ti f oil leak 6 3 Inspection of oil lea ST All of fittings for hydraulic hose pump cylinder etc may loose after 50 hours operation The fittings should be securely fastened The level sensor is attached to the hydraulic fluid tank If the amount of hydraulic oil decreases about 2Liters the warning alarm discontinuous sounds will sound 6 4 Greasing each part Carry out the greasing up to the following grease nipples every 50 hours Rear wheel parts 1 mower joint fitting 1 place Kingpin 2 places OT 2 lift arm 1 place Pivot 1 place 42 2 rotation fitting 1 place Pedal parts 43 2 mower joint fitting 1 place 3 Brake pedal 1 place 3 lift arm 1 place Brake fitting 1 place 3 rotation fitting 1 place Forward pedal 1 place 3 mower joint fitting 1 place 6 Backward
45. lamp Glow lamp Y Charge Glow ue 55 0 4 d se C The lamp turns on when the ignition switch is in the ONT position After the engine starts the light will be turned off if the oil begins to circulate and it becomes the normal pressure When the lamp is turned on during operation stop the engine immediately and carry out the maintenance and repair 4 7 Oil pressure lamp Engine oil pressure lamp Engine oil pressure lamp A Y Charge Glow Engine oil V V pressure 4 ry t 57e 9 Mowing operation Ple ZA d Pull up the throttle lever and set engine speed to MAX 2 600rpm Refer to 3 17 Set the 2WD 4WD changeover switch to the 4WD position Refer to 3 14 Set the Travelling Mowing changeover switch to the Mowing position Refer to 3 13 Set the reel reverse rotation switch to the ON position Refer to 3 16 Release the Mower lock lever Refer to 3 22 Move the mower unit raise lower lever to the DOWN position and ensure lower the mower unit to the ground Refer to 3 18 7 Move reel rotation switch to the ON position and rotate the reel Refer to 3 15 8 Hold the Forward pedal down and begin the operation Respond to the raising or lowering of the mower unit the reel will rotate or stop automatically Be sure to operate by the speed that suite
46. mbol Fuel Overturn fall No 2 Diesel fuel only Warning symbol a Grease Caution exhaust gas Warning symbol n Caution symbol Danger symbol Flying objects Gerges zR Danger symbol Cutting of hand or foot ke pe AK Be sure to observe for safe operation The precautions that are described here are the important contents concerning safety Be sure to follow these safety precautions Failure to follow these precautions can cause injury or death or accidents or damage to the machine The information described in this manual may vary from the actual machine purchased 1 General precautions UI E Do not operate the machine under the following conditions f you cannot concentrate while operating the machine due to fatigue or illness or if you are under the influence of medication After drinking alcohol e If pregnant If less than 18 years old or untrained person Failure to observe these precautions can cause an unexpected accident Wear suitable clothes when operating the machine Do not wear a towel around your head or waist or a scarf around your neck Wear safety glasses a helmet and slip X resistant shoes Use protective gear suitable for the working conditions and do not wear loose fitting clothes Failure to observe this precaution may cause you to get caught in the machine or to slip and fall 7 94 aD POLS An aam E Wh
47. nd do not smoke while refueling Refuel before mowing Do not remove the fuel tank cap when the engine is running or when the engine is hot f fuel is spilled do not start the engine Move the machine away from the area where the fuel was spilled and avoid creating any source of ignition until the spilled fuel has completely dissipated Close the fuel tank and fuel container cap securely Replace muffler when it is broken Repair any sensors that are malfunctioning before operating the mower Check that the seat switch and safety switch and the safety guards and covers are installed correctly and that they function properly Repair these parts if there is a malfunction before operating the mower 3 Precautions during operation Do not start the engine in a closed space since there is a danger of carbon monoxide poisoning Operate the mower during the day or in an area with sufficient lighting Before starting the engine disengage all equipment place the gearshift into neutral and set the parking brake Sit on the seat and start the engine Remember that there is no such thing as a safe slope Operating on grassy slopes requires particular care To avoid overturning Do not stop or start suddenly on any slope Reduce speed when travelling and making sharp turns on slopes Always stay alert for bumps hollows and other hidden obstacles Never mow across the surface of the slope unless the mower is designed to
48. ng brake Otherwise the brake disc and the hydraulic equipment are damaged Forward pedal Backward pedal Warning The travelling in the public road is not permitted by law 3 9 Speed limiter lever 3 11 Tilt steering It is a shift lever which restricts the forward pedal step in amount The step in amount decreases if it turns to the SLOW side Steering e Pull lever up to release steering column Tilt column up or down to position e i SLOW FAST desired Push lever back to lock steering Zu column in place der En Release Je RN Ms N Lock Speed limiter lever Tilt lever Be sure to make set to SLOW position when travelling by two wheel drive If make set to FAST position it becomes too fast when the pedal is fully pressed in Never adjust steering while machine is moving To prevent serious accidents ensure tilt steering lever is 3 10 Adjustment of seat e fastened during operation D The seat can be adjusted forward and backward by the seat lever 1 Angle adjustment of the reclining backrest can be performed by the lever 2 Hardness of the seat suspension can be 3 12 Switches levers on the operation panel a Travelling Mowing changeover switch e Throttle lever b 2WD 4WD changeover switch f Mower unit raise lower lever adjusted by turning the
49. ngine cool down enough when storaging the machine in the shutted place Lower the mowing unit when storaging the machine In case to store the machine with raising the outermost 4 and 5 mowers be sure to latch them To use the Baroness mower safely The following precautions should always be followed to operate the Baroness mower safely Warnings for Safety Warning symbols have been attached to this machine to ensure that you can operate it safely The warning symbols indicate items which are particularly important for your safety It is important to always follow the warnings and operate the machine with safety Warning symbols AA Danger e e e This symbol indicates that serious injury or death will occur if the warning is ignored in g e e e This symbol indicates that serious injury or death could E occur if the warning is ignored Caution lees This symbol indicates that an injury or damage to property may occur if the caution is ignored Refer to the operator s manual cee Symbol j Caution symbol utting of finger alitis Hot surface progre Danger symbol catching S i Caution symbol of hand or foot C SC Entanglement Danger symbol Danger flammables _ ib IER mme Sete safty clothes Pinch Caution symbol Z Pinch Warning symbol High pressure oil tc Caution symbol po V belt rotating parts Warning sy
50. o pinch your fingers etc while making adjustments to the mower For mowers equipped with multiple reel cutters take care as rotating one reel cutter can cause other reel cutters to rotate Before servicing or adjusting the mower stop the mower stop the cutting units set the parking brake turn the engine off and remove the key for gasoline engines disconnect the spark plug lead Be sure to check that each part has completely stopped operating before servicing or adjusting the mower When necessary use a jack to securely support the mower Take care when removing equipment the spring or oil pressure that have applied to it could be suddenly free When servicing the mower disconnect the battery lead To disconnect the battery disconnect the negative battery cable first then the positive battery cable To connect the battery connect the positive battery cable first When checking the reel cutters wear gloves or wrap the reel cutters in thick cloth to avoid injury Keep hands and feet away from moving parts If possible avoid making any adjustments while the engine is running Charge the battery in a well ventilated area away from sparks and flames Unplug the battery charger before connecting or disconnecting it to the battery Also wear protective clothing and use insulated tools Be sure to empty the fuel tank and keep apart from the fire origin when storaging the machine indoors where using spark or naked flame Check the e
51. ople especially children or pets are nearby Keep in mind that the owner operator or mechanic is responsible for preventing accidents and accidents can be abolished with the cooperation of all Never carry passengers other than the operator All operators and mechanics should receive proper training The owner is responsible for training the operators and the following must be thoroughly understood The basic safety precautions for operating ride on mowers It gets difficult to control the mower by applying the brake when it begins to slide on a slope The main reasons it is impossible to control the mower on a slope are Insufficient tire grip Driving too fast Inadequate braking Using a model inadequate for the job Lack of awareness of the ground conditions bumpy icy muddy 2 Preparation Use clothing and equipment that are suitable for the job Wear a helmet safety glasses and ear protectors Long hair loose clothing or jewelry can get tangled in moving parts Do not operate the mower when barefoot or wearing sandals Thoroughly check that the area where the mower is to be used is free of objects that can be thrown by the mower such as rocks toys and wire before starting Do not operate the mower under the influence of alcohol or drugs Warning Fuel is highly flammable Take the following precautions Store fuel in containers specifically designed for this purpose Refuel outdoors only a
52. ore removing blockages Before checking cleaning or servicing the mower After striking a foreign object or an abnormal vibration occurs on the mower W When turning the engine off close the throttle and close the fuel valve if your model is equipped with one W Keep hands and feet away from the cutting units W Before backing up look down and behind you to check that the path is clear and you can back up safely Have someone guide you if it is difficult to check the area behind you B Reduce speed when turning or crossing roads or sidewalks and proceed by taking extreme caution with your surroundings Also be sure to stop the rotation of the reel cutter W Take care when loading or unloading the mower onto a trailer or truck W Use care when approaching blind corners shrubs trees or other objects that may obscure your vision 4 Maintenance and storage Park the machine on the flat ground Never let indisciplined person fit out the machine Check that all nuts bolts and screws are properly tightened to ensure that the mower is always working under safe conditions To prevent a fire keep the engine muffler and battery areas free of excessive grease grass leaves and dust Check the grass catcher frequently for preventing wear or damage Keep all parts of the mower in good working condition and all fasteners and hydraulic fittings tightened If the fuel tank needs to be cleaned clean it outdoors Take care not t
53. put the 2WD 4WD changeover switch into 2WD 4 When the front wheel rotates in the forward direction loosen the locknut and turn in the direction that reduces the length of the neutral adjustment rod When rotating in the backward direction turn in the direction that extends the length of the neutral adjustment rod Find the position at which the front wheel stops and tighten the locknut Traction when the machine is fl unable to travel Ve P 1 When the engine is running stop the engine 2 Apply the parking braking and attach a wheel stopper 3 Set the 2WD 4WD changeover switch into 2WD 4 Raise the seat upward 5 Turn 90 degrees of the unloading valve beside the hydraulic pump Neutral Locknut 9 2 Unloading valve When you tow drive carefully at a low speed When you put the engine into operation next time be sure to start after returning the unloading valve 10 Long term storage e Fe m 07 tO LL Please refer to the Engine Battery operation manuals for details Clean up dirt grass and oil spot etc Inspect and replace the engine oil and air filter element Refill oil and apply lubricating greasing to each lubrication part Empty the fuel tank and keep the mower away from ignition sources when storing the mower indoors where sparks and open flames are used Set the air pressure in the tires slightly higher than normal place the machine on a board
54. quivalent type Never mix different kind of the hydraulic oil The tank capacity is approximately 44L 1 5 Cleaning of the air cleaner Perform the inspection with the vacuum pressure indicator If the element of the air cleaner becomes dirty the red ring is visible in the vacuum pressure indicator Remove and clean the air cleaner If the element of the air cleaner is dirty it will become the cause of the engine malfunction When it s dirty clean it by carefully tapping the element or blowing air from inside so that the element may not be damaged Attach the element after clean up and push the reset button Exchange the element of the air cleaner every 200 hours KT Air cleaner Vacuum pressure indicator Reset button 1 6 Inspection of the engine and its surroundings RE necessary Please refer to Operating and instruction manual for engine for handling of the engine 1 The parts of the fuel system should check whether there is neither the crack nor the leak and replace it with new one if 2 When the grass the leaf etc have jammed to the inside of the muffler and exhaust pipe or the surroundings blow out by air iibi 1 7 Inspection of the tires Inspect the tire pressure crack damage and unusual wear Tire pressure Front wheel 150kPa 1 5kgf cm Rear wheel 140kPa 1
55. rcuit which can cause burns and a fire Warning v addi mt of Le Od Ve lt amp E Do not allow the electrolyte to go below the LOWER level mark Check the electrolyte between the UPPER and LOWER level marks and that it is not below the LOWER level marks This comment is just for the battery equipped originally In case the replacement battery is maintenance free you do not need to check the level of electrolyte Failure to follow this precaution can cause the pole connector in the container to be exposed from the electrolyte if it is below the LOWER level mark which can cause sparks when starting the engine and the gas in the container to ignite causing an explosion E Take precaution with high pressure oil Always check if the hydraulic fittings and hoses are loose or damaged When disconnecting the fittings and hoses release the pressure in the hydraulic circuit Failure to follow this precaution can cause the high pressure oil to break through your skin and cause an injury A Caution VM VOD sei Be sure to check the electrical parts and wires Check if the electrical wires are touching other parts if the covering is damaged or if the connector is loose every day before operating the machine Failure to follow this precaution can cause a short cut and a fire Do not fill the tires with air over the specified maximum air pressure When filling the tires with air do not fill the tires over the spe
56. ritical When you adjust reel to bedknife stop the engine and remove Caution the ignition key 1 Set Bypass valve on hydraulic motor to Stop position then reel cylinder will free rotate Refer to 3 20 2 Inspect the reel blade and bedknife to ensure properly engaged When the reel blade is properly adjusted to the bedknife the reel cylinder will spin freely and you should be able to cut two sheets of newspaper along the full length of the reel blade If the cutter adjustment nut is loosened contact between the reel and bedknife become hard and contact will become weak if it is tightened Cutter adjustment nut Pipe with the cutter adjustment screw 3 If no newspaper cutting due to wear or damage is evident the cutting edges should be corrected by the lapping process 4 If the reel cutter is worn out and the diameter becomes small the tension of the spring will become weak Loosen the pipe with the cutter adjustment screw and adjust the tension of the spring Both the reel cylinder and bed knife are the cutting tools When Danger you handle with them be careful of injury When you try cutting the newspaper be careful not to pinch your fingertip which turns the reel cutter Before doing this work be sure to apply the parking brake firmly
57. rmance for an extended period of time Note Gradual changes may be made to the machine When making enquiries about the machine be sure to specify both the model type and serial number The information described in this manual may change without prior notice A Caution e e e About operation The warning labels that are attached to the machine and used in this manual contain information to maintain safety Please read the operating procedures and safety precautions carefully and only operate the machine after you have understood them completely The warning labels and their descriptions should be preserved in their entirety If they are lost or damaged please replace them immediately with new ones Do not under any circumstances remove the warning labels that are attached to the machine Introduction Read this manual carefully to thoroughly understand the proper operating and maintenance methods of your mower and to avoid causing injury to yourself and to others The operator is responsible for operating this machine properly and safely Never perform maintenance and repair which are not explained in this manual If a maintenance and repair is required an engineer who has technical knowledge and understood the service manual enough should do the work For questions concerning maintenance or genuine parts please contact your local Baroness dealer When making inquiries about your mower please specify the mower s
58. rry out about 1g 1 to 2 times with manual type small grease gun grease up for each part with the grease Excelite EP No 2 respectively A every 10 hours B Eevery 50 hours rz GE A every 10 hours B Eevery 50 hours T BI A every 10 hours B Eevery 50 hours 1l 32 7 2 Cutting height adjustment 1 Set the supplied cutting height gauge bar To avoid personal injury and damage by the cutting edges wear groves and handle the reel and bedknife with extreme care 1 Small adjusting screw for the cutting height setting 2 Small adjusting screw for the bed knife angle adjustment 3 Small adjusting screw for the Groomer adjustment 1 Set the a screw to desired cutting height 2 Set the included angle of the bed knife with the screw of b by referring to the following table Example When the angle of the bed knife is 5 degrees and 15mm of cutting height use 12mm A Bed knife angle 0 Value of B 7 Cutting height of A 0 6mm 6 Cutting height of A 1 8mm 5 Cutting height of A 3 0mm 4 Cutting height of A 4 2mm 3 Cutting height of A 5 4mm 2 Cutting height of A 6 6mm 1 Cutting height of A 7
59. s Bl Do not modify the machine Do not modify the machine Failure to follow this precaution can cause an accident or injury or the machine to malfunction E Inspection and maintenance Be sure to perform checks and maintenance before and after operating the machine Failure to follow this precaution can cause an accident or injury or the machine to malfunction Bl Performing the periodic checks and maintenance Perform the periodic checks and maintenance every year and maintain each part Be sure to change the power steering hose every two years and to check the electrical wires every year failure to follow this precaution can cause an accident or the machine to malfunction due to improper maintenance VE NS E Caution of reel mower Do not insert hand foot or other things to the rotating part where dangerous during operation or maintenance Remove obstacles such as rocks before using machine they cause the damage of reel cutter and bed knife and fry apart to invite an accident In case the obstacles get caught in the reel cutter switch the engine off and remove it after stopping the driving unit completely Protective cover and belt cover prevent the risk of operator when they damaged replace them and settled in the proper position 3 Inspection and maintenance before and after operating the machine L Danger ol amp E Add oil and refuel when the engine is cold Do not add oil or refuel when th
60. sesssesesseesestetessseeeesseeeen 21 3 8 iWaming Forward Backward pedal sss 21 3 9 A Caution Speed limiter lever ssssseese es 22 3 10 Adjustment of seat 22 3 11 A Caution Tilt steering eee cssssssecececsesesesesesessseecsesesescsesesseeceeeceesesesens 22 Ti A Caution After operating the machine and storage 11 3 12 Switches levers on the operation Done 22 Names GEIER 13 3 13 Travelling Mowing changeover switch 23 3 14 uti CS ann ms Warning label and operation label attachment locations 14 ie inn changeover swich x _ 3 15 Reel rotation switch Mowing ss ssssssssnsssnsssrnsssrnssrnnnsrnene 23 Warning label and operation label descrption 15 3 16 Reel reverse rotation Switch 24 Features of LM2700 E 16 3 17 Throttle lever 24 ee 16 3 18 Mower unit raise lower lever En 24 TEE 3 19 Differential lock switoli tertia nad rra evi ced dines 24 STEE SO Ss eege eege een 25 1 Inspection DefOle ES Nan i Tf 3 21 Reel rotation adjusting valve 25 1 1 A Caution Cleaning of the radiator and oil cooler 17 3 22 Mower lock lever l tgh sssmtinimemmnnmeienenentees 25 1 2 A Caution Inspection of the radiator and coolant level 17 3 23 Groomer clutch lever option 29 4 Measuring Instrument 44 4 2 Tachometer amp hour meter 4 3 Water temperat
61. tproof net Es ENN L C7 a If it does not clean it will become overheating of the engine and Caution the cause of the seizure Moreover it also becomes cause of the damage of the hydraulic equipment 1 2 Inspection of the radiator and coolant level Perform the inspection when the engine is cold The radiator cap is the pressure type If the radiator cap is removed when the engine is high temperature the steam blows off and it may cause burns After the water temperature and the pressure falls apply a thick cloth etc to the cap Then turn to the left gradually llli Deen and loosen and remove Check that the coolant level of the reserve Cap Reserve tank tank is between FULL and LOW When the coolant is below the line of LOW add the coolant from the cap part of the reserve tank to the line of FULL When there is no coolant in the reserve tank supply it also from the cap part of the radiator to the top Do not open the radiator cap in normal inspection When the coolant level decreases supply clean water only Please drain the cooling water before winter or mix the long life coolant Perform the drainage by the drain plug in the left side of the machine Drain plug Standard long life coolant LLC consistency and the freezing point Freezing point LLC consistency volume Up to
62. ture Masahisa Nakazawa Manager Quality Dept Kyoeisha Co Ltd Date 2006 42 EC 2004 108 EC November 4 2010 E Age 92d4S 00 101 Z49 NN 00 CN 1 uedef 0 S9 Zrt JeJg Iuorv Z9 68 50 xe4 emeyoho ouo pin AIN 9z L 990 PESH O6 L v8 EGO 18L ess OUT OO VHSIAOAM
63. ure gauge ssssse meme 4 4 Fuel gauge eine Mines Mili HER IEEE DR IEEE Fa Hadas 4 5 erar 4 6 Thermostat lamp Glow Lamp 4 7 Oil pressure lamp Engine oil pressure Jamp 5 Mowing Operation eene nnne 6 Maintenance of the main unt 6 1 Change of engine oil rct deett et tee cea 6 2 Caution Change of hydraulic ol 6 3 Inspection of oll leak iore a is 6 4 Grease up positions Greasing each part EE 6 5 Replacement of USOS eet dedans SER ERR eC Rode etre 6 6 Inspection of battery 6 7 Caution Opening and closing the engine bood 6 8 Caution Opening and closing the seat undercover 6 9 CCE Adjustment of brake 6 10 Air bleeding from fuel iie eie atento e e RR E RE ATP YR eens es 7 Main 7 1 tenance of the moWer eene eher nene n nnne daas 7 2 ig Cutting height adjustment 7 3 FES coron Adjusting the blades sseseeeeee 7 4 DESEN A caution Lapping 7 5 Caution Adjustment of the groomer option 7 6 Adjustment of the reel cover 7 7 Turning the 2 and 3 mower units Instruments of operation panel 8 Cautions for maintenance 36 8 1 Caution L Caution Cautions for m
64. wly When turning sufficiently reduce your speed Also sufficiently reduce your speed when operating on slopes bumpy roads or curves Failure to follow this precaution can cause the machine to overturn or fall causing damage to the machine Bl Use a running board to cross ditches When entering a field crossing ditches or traveling over a soft area be sure to use a running board Use non skid running board bearing sufficient strength length and width failure to follow this precaution can cause the machine to have an accident by slipping or overturning A Caution P gt B Set the parking brake while warming the engine up Failure to follow this precaution can cause the machine to move spontaneously and cause an accident 10 Bi When operating at high speeds do not operate the brake pedal suddenly failure to follow this precaution can cause the machine to overturn or fall 6 When operating the machine CES AA EC ES A ub A pocs ED D E Do not substitute weight for people or cargo Do not load people or cargo as a substitute for weight Failure to follow this precaution can cause an injury ws z Wear protective gear Be sure to wear safety glasses a helmet and slip resistant shoes failure to follow this precaution can cause an injury Do not go or place your feet under the operating machine Do not go or place your feet under the operating m

Download Pdf Manuals

Related Search

Related Contents

Philips LCD monitor with SmartControl Lite, Audio 191V2AB  1 le championnat de france 2014 - media  User Manual - LabCon-L - Laboratory Automatisation Modules  Icy Dock MB981U3-1SA-1  La Crosse Technology WT-2165 User's Manual  Sony DR-BT101IK User's Manual  sujet ep1 cap patissier juin 2010 metropole        

Copyright © All rights reserved. Failed to retrieve file