iq display module series 2 (iqdm series 2) - Club Car Side-by
Contents
1. the plug with the IQDM jack and connect the plug to the jack Figure 2 3 or 4 Page 4 IQDM Series 2 Handset Service Tool Owner s Manual Plugging the Handset into the Vehicle Figure 2 Vehicle Connection IQ System IQ Plus and Figure 3 Vehicle Connection Under Dash Precedent DS Vehicles with Data Port on F amp R Switch Vehicles and 2007 and later IQ Plus Vehicles as Shown Here Note Seat shown in illustration may not match all models ADM Figure 4 Connector Under Seat In Extended Position DS Vehicles without Data Port on F amp R Switch IQDM Series 2 Handset Service Tool Owner s Manual Page 5 Introductory Display INTRODUCTORY DISPLAY Immediately after the handset is connected to the vehicle it begins loading the vehicle speed controller infor mation Figure 5 After a few seconds the screen displays the following menu items Figure 5 e Monitor e Faults e Functions e Information Programmer Setup In the event that the handset does not display any information or the screen is difficult to read refer to the IQDM Series 2 troubleshooting procedures See IQ Display Module Series 2 IQDM Series 2 Program ming in the appropriate maintenance and service manual Monitor Faults Functions Information Programmer Setup Figure 5 Introductory Display Figure 6 Main Menu Display Page 6 IQDM Series 2 Handset Service Tool Owner s Manual Menu Nav2. IQ DISPLAY MODULE SERIES 2 IQDM SERIES 2 OWNER S MANUAL The IQDM Series 2 is a handheld programming and diagnostic tool for use with Club Car IQ Sys tem vehicles This owner s manual includes all information required to operate the IQDM Series 2 with Club Car IQ System and IQ Plus vehicles but does not contain detailed informa tion for troubleshooting the vehicle Refer to the vehicle maintenance and service manual and supplement for detailed vehicle troubleshooting and service procedures For vehicle operation information refer to the vehicle owner s manual supplied with the vehicle If you do not have a vehicle owner s manual or a vehicle maintenance and service manual and supplement they may be obtained from your Club Car dealer or distrib utor Manual No 102249203 For use with Kit No 102248803 Edition Code 0603C1006B O AE i I Notice NOTICE This manual contains proprietary information that is protected by copyright All rights are reserved No part of this manual may be photocopied reproduced or translated to another language without the written consent of Club Car Inc Club Car is not liable for errors in this manual or for incidental or consequential damages that result from the use of the material in this manual The information contained in this document is subject to change without notice Club Car reserves the right to make design changes to servi
3. age 7 Menu Navigation The following menus are accessible on the IQDM Series 2 handset Monitor The monitor menu displays values for certain parameters to facilitate speed controller troubleshooting See IQ Display Module Series 2 IQDM Series 2 Diagnostics in the appropriate maintenance and service manual Faults The faults menu displays all faults recorded by the speed controller since the history was last cleared Each fault is listed only once even if the fault has occurred multiple times See IQ Display Module Series 2 IQDM Series 2 Diagnostics in the appropriate maintenance and service manual Functions The functions menu allows the user to transfer all current settings from the speed controller to the handset and from the handset to the speed controller See IQ Display Module Series 2 IQDM Series 2 Program ming in the appropriate maintenance and service manual Information The information menu displays the model number serial number manufacturer date and software version of the speed controller See IQ System Display Module Series 2 IQDM Series 2 Diagnostics in the appro priate maintenance and service manual Programmer Setup The programmer setup menu allows the user to set the LCD contrast display the fault history of the program mer as well as various other information pertaining to the handset such as model number serial number OEM information etc Page 8 IQDM Series 2 Handset Service Tool Owner s Manu
4. al Programmer Setup PROGRAMMER SETUP The programmer setup menu selection allows the user to set the LCD display contrast records the fault his tory of the handset and displays information pertaining to the handset PROGRAM This menu allows the user to adjust the contrast on the display screen After selecting the LCD Contrast menu use the change value buttons to adjust the contrast for the best readability FAULTS This menu selection displays faults that have been detected within the handset This fau ts menu does not pertain to any faults detected in the speed controller The following faults can be detected within the handset CODE NUMBER TEXT DISPLAYED 14 Communication error with controller 15 Error in handset 16 Handset does not support this function 17 Serial port overrun error 18 Security lockout on program menu Fault History This menu displays any faults that have been detected within the handset itself Clear Fault History The clear fault history function will erase the history of faults that are stored in the handset Information This menu selection displays information pertaining to the handset The information provided in this menu selection includes model number serial number the date the handset was manufactured the handset soft ware version etc IQDM Series 2 Handset Service Tool Owner s Manual Page 9
5. aveling as a passenger in the vehicle Failure to heed this warning could result in severe personal injury or death This owner s manual should be read completely before attempting to operate the IQDM Series 2 Failure to follow the instructions in this manual could result in property damage severe personal injury or death Only trained technicians should repair or service the vehicle Anyone doing even simple repairs or service should have knowledge and experience in electrical and mechanical repair Follow the procedures exactly as stated in this manual and heed all DANGER WARNING and CAUTION statements in this manual as well as those affixed to the vehicle Improper use of the vehicle or failure to properly maintain it could result in decreased vehicle performance or severe personal injury Any modification or change to the vehicle that affects the stability or handling of the vehicle or increases maximum vehicle speed beyond factory specifications could result in severe personal injury or death Check the vehicle owner s manual for proper location of all vehicle warning decals and make sure they are in place and are easy to read Wear safety glasses or approved eye protection when servicing the vehicle Wear a full face shield and rubber gloves when working on or near batteries Turn key switch to the OFF position and remove key place Forward Reverse switch in the NEUTRAL position and chock the wheels prior to servicing the vehi
6. ce tools and vehicles without obligation to make these changes on units previously sold This manual effective December 1 2003 Copyright 2003 2006 Club Car Inc TABLE OF CONTENTS Safety Details ria Logos vie ih ame hau nein hund ale ta da apa lea 3 Parts Included inKit s 0sn nennen nennen ee een en 4 Supplying Power To The IQDM ooococcccccoo nennen nennen nennen 4 Programmer Set ir ine ee date er Balin a u ee Pes ac 9 Page 2 IQDM Series 2 Handset Service Tool Owner s Manual Safety Details SAFETY DETAILS A DANGER Battery Explosive gases Do not smoke Keep sparks and flames away from the vehicle and service area Ventilate when charging or using in an enclosed space Wear a full face shield and rubber gloves when working on or near batteries Use extreme caution when using tools wires or metal objects near batteries A short circuit and or spark could cause an explosion Battery Poison Contains acid Causes severe burns Avoid contact with skin eyes or clothing Antidotes External Flush with water Call a physician immediately Internal Drink large quantities of milk or water Follow with milk of magnesia or vegetable oil Call a physician immediately Eyes Flush with water for 15 minutes Call a physician immediately A WARNING The vehicle operator should not monitor the handset while the vehicle is in motion A technician can monitor the handset while tr
7. cle Do not wear loose clothing or jewelry such as rings watches chains etc when servicing vehicle Moving parts Do not attempt to service the vehicle while it is running Use insulated tools when working near batteries or electrical connections Use extreme caution to avoid shorting of components or wiring If wires are removed or replaced make sure wiring and wire harness are properly routed and secured Failure to properly route and secure wiring could result in vehicle malfunction property damage or personal injury IQDM Series 2 Handset Service Tool Owner s Manual Page 3 Parts Included in Kit CAUTION Do not expose the handset to direct bright sunlight for long periods of time Failure to heed this caution could result in damage or failure of the IQDM Series 2 PARTS INCLUDED IN KIT The IQDM Series 2 kit should include the items shown Figure 1 Q SYSTEM IQDM SERIES 2 HANDSET IQDM SERIES 2 CABLE CABLE ADAPTER IQ PLUS DECAL 102241803 102241502 102251501 102249101 Figure 1 IQDM Series 2 Parts SUPPLYING POWER TO THE IQDM When connected to a vehicle the IQDM Series 2 handset is powered entirely by the vehicle batteries through the speed controller PLUGGING THE HANDSET INTO THE VEHICLE 1 Connect one end of the cable to the jack located on the bottom of the handset 2 Connect the cable adaptor to the IQDM Series 2 cable 3 Remove the dust cap from the IQDM jack 4 Align the keyed portion of
8. igation MENU NAVIGATION The NAVIGATION BUTTON is the four arrow button located on the left side of the handset Figure 7 This button is used to navigate through and select menus Pressing the up or down arrows allows the user to scroll through the menu items When the box beside the desired menu is blinking pressing the right arrow selects that menu item Pressing the left arrow allows the user to go back one screen The CHANGE VALUE BUTTON is the button located on the right side of the handset Figure 7 This button allows the user to change values by pressing or The three yellow buttons labeled 1 2 and 3 are BOOKMARK BUTTONS Figure 7 These buttons allow the user to bookmark up to three specific screens for rapid return to those screens To bookmark a specific dis play screen have the desired screen displayed and simply press and hold a bookmark button until the state ment bookmark set is displayed When it is necessary to go back to the bookmarked screen rapidly press and release the appropriate bookmark button See following NOTE NOTE When going to a bookmarked display screen be sure to rapidly press and release the button If the button is pressed and held for too long the bookmark will be overridden with the current screen E DISPLAY SCREEN NAVIGATION BUTTON CHANGE VALUE BUTTON BOOKMARK BUTTONS Figure 7 Handset Controls IQDM Series 2 Handset Service Tool Owner s Manual P
Download Pdf Manuals
Related Search