BOOM! AUDIO STAGE II FRONT FAIRING - Harley
Contents
1. The left speaker trim ring has no text Rotate the speaker so the tweeter E is at the top inboard of the upper mounting hole 4 From the inside insert the correct tweeter midrange speaker assembly 2 or 3 through the speaker opening in the inner fairing Secure with three TORX screws F removed earlier Tighten to 9 13 in lbs 1 0 1 4 Nm 5 Repeat steps 2 4 for the opposite speakers 6 Install one speaker enclosure to the inner fairing Secure with three hex socket screws see Figure 1 Item 9 removed earlier Tighten to 48 60 in Ibs 5 4 6 8 Nm 7 Secure the lower portion of the enclosure to the fairing support bracket 5 with three hex head socket screws 6 removed earlier Tighten to 20 24 ft los 27 1 32 5 Nm 8 Secure the enclosure to the upper support bracket with two hex socket screws 8 Tighten to 48 60 in Ibs 5 4 6 8 Nm 9 Repeat steps 6 8 with the remaining enclosure 10 Position the Y harness see Figure 2 Item 5 inside the fairing e Connect the four way connector 313 of the Y harness into the amplifier harness rear speaker output connector 313 e The Y harness legs are labeled RH or LH right side or left side as viewed from the rider position Or match the wire colors of the Y harness to the speaker wire colors Route each leg of the harness to the correct speaker e Plug in the two way connectors at each speaker 11 Mate the speaker and power port connectors Secure2. clutch lever side only CB equipped models Unplug the CB connector 184 4 and CB antenna See the service manual DO NOT remove the module 4 Remove the three screws 6 securing the lower portion of the enclosure to the fairing support bracket 5 5 Remove two screws 8 securing the upper portion of the enclosure to the upper support bracket 7 1 of 4 Please dispose of materials responsibly is07432 Speaker enclosure Fairing harness anchor Speaker connector CB connector Fairing support bracket Upper support bracket Screw hex socket 1 4 20 x 1 2 in 13 mm long 2 Screw hex socket 1 4 20 x 3 4 in 19 mm long 3 10 DO NOT remove these screws 13 11 Original 5 1 4 in 133 mm speaker 12 Screw TORX 10 x 1 2 in 13 mm long 4 13 Speaker wire connectors 14 Speaker grille 15 Screw TORX 10 x 3 8 in 10 mm long 3 16 Alignment pin 17 View in direction of arrow OON DUA OND Screw hex head socket 5 16 18 x 3 4 in 19 mm long 3 Figure 1 Speaker Enclosure Removal Left Side Shown NOTE Do not remove any of the screws 10 securing the speaker enclosure halves together 6 Remove three screws 9 securing the speaker enclosure to the inner fairing Remove the speaker enclosure from the vehicle Save the screws 7 Remove four screws 12 to free the speaker 11 from the enclosure Save the screws 8 Disconnect wires 13 Remove the speaker from the enclo
3. cMOTOR HARLEY DAVIDSON WY J05931 INSTRUCTIONS REV 2014 10 07 BOOM AUDIO STAGE II FRONT FAIRING SPEAKER KIT FLHT FLHX GENERAL Dealer installation is recommended Radio EQ update using the Digital Technician II diagnostic tool is e Recommended before speaker INSTALLATION e Required before audio system OPERATION e Only available through authorized Harley Davidson dealers Kit Number 76000524 Models For model fitment information see the P amp A retail catalog or the Parts and Accessories section of www harley davidson com English only Installation Requirements NOTE DO NOT mix Stage and Stage Il speakers on the same vehicle NOTICE Radio EQ MUST be updated by a Harley Davidson dealer BEFORE operating the audio system Operating the audio system prior to radio EQ update will IMMEDIATELY damage the speakers 00645d NOTES e These speakers MUST be used with an amplifier Prior installation of a Fairing Amplifier kit Part No 76000278 is required The amplifier mounts inside the upper fairing e The speakers in this kit have an impedance of 2 Ohms They are for use ONLY on 2014 and later Harley Dav idson audio systems See the P amp A retail catalog or the Parts and Accessories section of www harley dav idson com English only e Using these speakers on 2006 2013 Harley Davidson audio systems WILL permanently damage these Speakers e Using these speakers on 2005 or earlier Har
4. ley Davidson audio systems WILL permanently damage those sys tems J05931 amp Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled WARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is required for this installation One is available from a Harley Davidson dealer Kit Contents See Figure 2 and Table 1 PREPARATION WARNING To prevent accidental vehicle start up which could cause death or serious injury remove main fuse before pro ceeding 00251b NOTE e WITH security siren With security fob present turn ignition switch ON See the service manual After system is disarmed turn ignition switch OFF IMMEDIATELY remove the main fuse e WITHOUT security siren See the service manual Remove main fuse REMOVAL 1 Remove outer fairing Remove windshield See the service manual 2 See Figure 1 Remove the harness anchor 2 from each speaker enclosure 1 3 Right brake lever side only Unplug the power port connector C132B not shown Left
5. sure Discard the speaker 9 Remove the three screws 15 securing the speaker grille 14 to the inner fairing Remove the speaker grille from the fairing Save the screws Discard the grille 10 Repeat steps 3 9 to remove the remaining speaker enclosure speaker and grille NOTE Never operate vehicle with the speaker enclosures removed These components provide important structural support to the J05931 fairing Operating without these components can result in damage to fairing assembly INSTALLATION 1 Install Fairing Amplifier Kit Part No 76000278 to the inner fairing per the instructions in that kit 2 See Figure 2 On one side attach the speaker jumper wire connectors B inside the speaker enclosure A to the spade terminals on the back of the new woofer 1 Dif ferent size spade contacts prevent improper assembly NOTE Position the woofer over the opening in the speaker enclosure Note the letters A and B stamped on the outer rim C of the speaker e For the left speaker rotate so the letter B is at the bottom For the right speaker rotate so the letter A is at the bottom 2 of 4 3 Fasten the speaker to the enclosure with the four screws D removed earlier Tighten the screws to 14 20 in lbs 1 6 2 3 Nm NOTES The tweeter midrange fairing speaker assemblies are side specific The right speaker trim ring has the text BOOM AUDIO STAGE I to the right of the tweeter housing
6. the harness anchors to the speaker enclosures 12 Left side only CB equipped models Plug in the CB connector 184 and CB antenna See the service manual J05931 WARNING Be sure that steering is smooth and free without interfer ence Interference with steering could result in loss of vehicle control and death or serious injury 00371a e Make sure that wires harnesses or lines do not pull tight when handlebars are turned fully to left or right fork stops 13 Verify that steering is smooth and clear from stop to stop COMPLETION NOTE To prevent possible damage to the audio system verify that the ignition and audio system are OFF before installing the main fuse NOTICE Radio EQ MUST be updated by a Harley Davidson dealer BEFORE operating the audio system Operating the audio system prior to radio EQ update will IMMEDIATELY damage the speakers 00645d 1 See the service manual Install main fuse 2 Have a Harley Davidson dealer update the radio EQ using Digital Technician Il 3 Turn the ignition ON but do not start the motorcycle 4 Refer to the BOOM BOX INFOTAINMENT SYSTEM section of the owner s manual Turn the radio ON Make sure that all speakers are working and front rear fader function is operating correctly If not check speaker wiring Understand that buzzing squeaks and rattles could be heard until outer fairing is installed 5 See the service manual Install the outer fairing and
7. windshield WARNING After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b 6 See the service manual to install the seat IN USE Avoid direct contact with speaker grilles by a pressure washer Damage to speakers can result 3of4 SERVICE PARTS is08446 Figure 2 Service Parts BOOM Audio Stage II Front Fairing Speaker Kit FLHT FLHX Models Table 1 Service Parts Item Description Quantity Part Number Fairing speaker assembly woofer 2 76000525 2 Speaker assembly tweeter midrange right includes Item 4 76000535 3 Speaker assembly tweeter midrange left includes Item 4 76000536 4 e Label speaker installation Not sold separately 5 Wire harness tweeter midrange speaker assembly 69200925 Items mentioned in text but not included in kit A Speaker enclosure 2 B Speaker jumper wire connector 4 C Reference hole at bottom of speaker frame marked A left speaker B right speaker D Original equipment OE screw 0 5 in 13 mm long 8 E Tweeter bridge F OE screw 0 4 in 9 5 mm long 6 J05931 4 of 4
Download Pdf Manuals
Related Search