POND FOUNT POND FOUNTAIN PUMP
Contents
1. King Pumps Myers Pentair Pump Group POND FOUNTAIN PUMP Pump Installation and Service Manual 23833A564 1 3 WARNING IMPORTANT SAFETY INSTRUCTIONS READ CAREFULLY BEFORE INSTALLATION FAILURE TO FOLLOW THESE INSTRUCTIONS AND COMPLY WITH ALL CODES MAY CAUSE SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE Before installing or servicing your pump BE CERTAIN THE ELECTRIC POWER SOURCE IS TURNED OFF AND DISCON NECTED Never enter the water or allow anyone to enter the water either swimming wading or in a boat with the pump power on this MAY RESULT IN SEVERE ELECTRICAL SHOCK All installation and electrical wiring must adhere to state and local codes Check with appropriate community agencies or contact your local electrical and pump inspectors for help A licensed electrician should preform installation NO SWIMMING AND OR WARNING SIGNS SHOULD BE POSTED PER STATE AND LOCAL CODES Please affix included warning label to junction box or power receptacle on shore Do not connect the control box and pump toa power supply until the control box and pump are properly grounded CAUTION FAILURE TO GROUNDTHIS UNIT PROPERLY WITH GROUND FAULT PROTECTION MAY RESULT IN SEVERE ELECTRICAL SHOCK This pump is provided with a ground fault circuit protector This must be installed with the unit See installation instructions WARNING Reduce risk of electric shock during operation of this pump requires the provi2. appropriate cap to the top of the float This only needs to be hand tight no wrench is necessary Locate the two anchor rings attached to the clamps Attach a nylon cord or rope not provided to each ring The anchor ropes can be used to position the pond pump in the middle of the pond or they can be used to anchor the pump to the pond floor with weights In either case it is necessary to secure the pond pump so that it does not float around or spin If you plan to secure the pond pump with two anchor ropes secured to the pond bank then one rope or cord can be walked around to the other side of the pond and the pump and float can be pulled to the center of the pond using the second rope or cord to guide the float Both ropes should be staked and secured to hold the pump in place be sure the rope or cord is tight and does not let the pond pump float or twist If you plan on using two weights to anchor the pump in place be sure that they are placed 10 15 feet apart to insure that the float does not twist If no power is near the pond then the power lines should be trenched to the pond Check with local and state codes to insure that you are using proper procedures We recommend conduit but there are direct burial cables where codes permit CHECK WITH LOCAL UTILITY COMPANIES TO LOCATE EXISTING LINES BEFORE DIGGING OR INSTALLING A MOUNTING STAKE TO PREVENT PERSONAL INJURY AND OR DAMAGING EXISTING LINES 7 A stake or pole not p
3. ULAR PURPOSE AFTER THE TERMINATION OF THE WAR RANTY PERIOD SET FORTH HEREIN Some states do not permit some or all of the above warranty limitations and therefore such limitations may not apply to you No warranties or representations at any time made by any representatives of MYERS shall vary or expand the provision hereof LIABILITY LIMITATION INNO EVENT SHALL MYERS BE LIABLE OR RESPONSIBLE FOR CONSEQUENTIAL INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR RELATED IN ANY MANNER TO ANY MYERS PRODUCT OR PARTS THEREOF PERSONAL INJURY AND OR PROPERTY DAMAGE MAY RESULT FROM IMPROPER INSTALLATION MYERS DISCLAIMS ALL LIABILITY INCLUDING LIABILITY UNDER THIS WAR RANTY FOR IMPROPER INSTALLATION MYERS RECOMMENDS FOLLOWING THE INSTRUCTIONS IN THE INSTALLATION MANUAL WHEN IN DOUBT CONSULT A PROFESSIONAL Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from state to state In the absence of suitable proof of the purchase date the effective date of this warranty will be based upon the date of manufacture Direct all Notices etc To Service Department MYERS 1101 Myers Parkway Ashland Ohio 44805 F E Myers 1101 Myers Parkway Ashland Ohio 44805 1969 419 289 1144 Fax 419 289 6658 www femyers com 5 23833A564
4. ecking the ground the power can be turned on Check the operation of the GFI by pushing the test button The unit should stop Pushing the reset button can reset it If the unit does not stop by pushing the test button have this checked out by a qualified licensed electrician 23833A564 TYPICAL INSTALLATION Signs should be posted NO SWIMMING f 6nd paad DYM pone p p no oono Penaiddy SP02 e20 d punoa SPUN Spul 9 5 Aung q p inb i aq A u pio mod amp 10yS UO SSS Q PAPeRe aq UD 23833A564 TROUBLESHOOTING GUIDE 1 Circuit breaker tripped reset 2 GFI ground fault interrupter protector tripped reset Problem Unit won t pump 1 Electrical storms will trip GFI reset 2 Short in system Disconnect power and check cord See instructions if unable to find short contact an electrician unitspins 1 Check anchor ropes to insure it is secure Unit won t spray 1 Unit plugged disconnect power flush screen and nozzle with hose After it is unplugged check the depth of the pond The unit may be in too shallow of section move to a deeper section Pond must be 5 feet deep WARRANTY MYERS will repair or replace for the original user any portion of your new MYERS product which proves defective due to defective materials or workmanship of MYERS Contact the nearest authorized MYERS dealer for warranty service MYERS shall possess the sole right to determine whethe
5. ied licensed electrician 13 Do not pump gasoline chemicals corrosives flammable liquids or any substance other than water they could ignite explode or damage the pump causing injury and voiding the warranty 14 Do not run this pump with the discharge completely blocked This will create super heated water which could cause injury damage the seal melt the plastic pipe fittings and shorten the life of the motor This super heated water could cause severe burns This pump is capable of building pressures in excess of 100 PSI 15 Do not pump water above 120 degrees Fahrenheit 16 The junction box should be mounted in an area that will not flood or be submerged with water After installation and service always make sure to secure the junction box lid with the screws provided 17 Modifying or altering this product may result in severe injury or death INSTALLATION INSTRUCTIONS 1 This pond pump should only be installed in ponds where no swimming wading or boating is allowed WHEN FISHING THE PUMP SHOULD BE TURNED OFF Appropriate signs should be posted per local and state codes The pump should be installed in ponds that are at least 5 feet deep to prevent clogging of the inlet screen After removing the pump screen and float assembly from the box ensure that the unit is undamaged and the hose clamp is tight around the bottom of the float Choose the spray pattern that you like and screw the
6. r to repair or replace defective equipment parts or components THIS WARRANTY DOES NOT COVER DAMAGE DUE TO LIGHTNING OR OTHER CONDITIONS BEYOND THE CONTROL OF MYERS PUMPS 12 months from date of purchase or 18 months from date of manufacture Receipt and product date code required for warranty claim LABOR ETC COSTS MYERS shall INNO EVENT be responsible or liable for the cost of field labor or other charges incurred by any customer in removing and or reaffixing any MYERS product part or component thereof THIS WARRANTY WILL NOT APPLY a to defects or malfunctions resulting from failure to properly install operate or maintain the unit in accordance with printed instructions provided b to failures resulting from abuse accident or negligence c to normal maintenance services d to units which are not installed in accordance with applicable local codes ordinances and good trade practices e if the unit is moved from its original installa tion location f if unit is used for purposes other than for what it was designed and manufactured g to products that have been modified PRODUCT IMPROVEMENTS MYERS reserves the right to change or improve its products or any component without obligation to provide such a change or improve ment for units sold and or shipped prior to such change or improvement WARRANTY EXCLUSIONS MYERS SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MER CHANTABILITY AND FITNESS FOR A PARTIC
7. rovided can be driven in the ground near the pond preferably on high ground to mount an outdoor weatherproof receptacle not provided Make sure the ground fault circuit interrupter is protected from the weather DO NOT USE AN EXTEN SION CORD This should be mounted high enough so that it will not flood If there is a building near by it can be mounted on the side of the building DO NOT INSTALL THE UNIT WITHOUT AN APPROVED GROUND FAULT CIRCUIT INTERRUPTER GFI Some local codes may require conduiting from the bank to the receptacle The ground fault circuit plug can be removed and conduit not provided may be installed over the cord Make sure the plug is installed the same way it was removed The green wire to G ground the white to N neutral and the black to L load A trench 3 to 6 deep can be dug from the bank to the receptacle to bury the conduit This step may also be required if muskrats are nearby Before connecting the pump to the receptacle check the installed pump to insure there is no leakage to ground This can be done by using an ohm meter and setting the scale to its highest setting Attach one lead of the ohm meter to the pump power cord ground round prong and one of the flat prongs It should read infinite or at least 2 mega ohms Repeat with the other prong If in doubt on the proper procedure contact a qualified licensed electrician 10 After installing the pump connecting up the power and ch
8. sion of acceptable grounding by connect ing a copper conductor at least the size of the circuit conductors supplying the pump to the ground screw provided within the wiring compartment of the power supply and to all metal junction boxes The voltage frequency and phase of the power supply must match the voltage frequency and phase of the pump motor This pump is provided with a 100 foot power cord and GFI protection do not attempt any underwater splices or replacement of the cord this will negate the safety listings void all warranties and could result in an unsafe and hazardous installation 23833A564 2 8 Donot work on the pump with the power on 9 Never install this pump with frayed or brittle power cord and always protect the cord from sharp objects hot surfaces oils and chemicals Avoid kinking the cord 10 Never service this pump with wet hands or while standing in or near water Use tools with insulated handles 11 To prevent damage to the cord use approved appropriate cord connectors to run the cords through the control box This pump motor is equipped with automatic resetting thermal protectors The motor may restart unexpectantly causing the leads to energize or pump to turn 12 Check for nicks in the wire by using an ohm meter to check for resistance to ground This can be done after installation but before the power is connected If in doubt on the proper procedure check with a qualif
Download Pdf Manuals
Related Search