Fluke 10 User Manual
Contents
1. is displayed Touch probes to the diode Figure 5A A forward voltage drop of about 0 6 V typical for a silicon diode causes the meter to beep once Reverse probes Figure 5B If the diode is good OL is displayed If the diode is shorted Figure 5C the beeper sounds continuously in at least one direction If the diode is open OL is displayed in both directions Testing Diodes acz05f eps Figure 5 Testing Diodes 13 10 Users Manual Maintenance Warning To avoid electrical shock or damage to the meter do not get water inside the case and remove the test leads and any input signals before opening the case Wipe the case with a damp cloth and detergent Do not use abrasives or solvents Replacing the Battery A Warning Replace the battery as soon as the low battery indicator E appears to avoid false readings that can lead to shock and injury To replace the battery 1 Turn the meter OFF and remove the test leads from the meter 2 Remove the four screws from the back of the meter and lift off the front 3 Remove the battery and replace it with a 9 V battery NEDA 1604 or IEC 6F22 14 Specifications Specifications This meter complies with Part 15 of FCC Rules Operation is subject to the following conditions 1 This meter may not cause harmful interference 2 This meter must accept any interference2. 3x 10 V Hz Maximum 2 4 to 3 0 V dc 2 400 V dc 0 95 mA typical 18
3. FLLIKE 10 Multimeter Users Manual 1991 2001 Fluke Corporation All rights reserved Printed in USA All product names are trademarks of their respective companies FLUKE 10 MULTIMETER an n nmv SL BE LJ Wa acz06f eps 10 Users Manual Contents Page Read First Safety Information ssssseeeeeeenenn 2 Contacting Fluke for Service Accessories or 3 Standby Mode an ettet ert o 4 Operating lt aa nnne nennen 5 cnn 6 KS ya Aa AAA A RE ada ad a O 6 Using the Autorange and Manual Range Modes 111111 7 Measuring Voltage iere toI EG Re R a Ea Saar 8 Testing Continuity And Measuring Resistance 10 Turning the Beeper Off 10 Testing Diode S si th ote aee AA PAZ A LE 12 Maintenance we m 14 Replacing the Battery 14 SpecifICatiOns xc desti O W za a epa per O REKIN 15 10 Users Manual Read First Safety Information Warnings and Cautions To ensure that the meter is used safely and to avoid damage to the meter e Use the meter only as described in this manual or the protection provided by the meter mi
4. and Manual Range Modes Using the Autorange and Manual Range Modes The range for each function determines the highest value the meter can measure If the range is too low the meter displays OL overload and beeps If the range is too high the display shows fewer digits of resolution The meter has an autorange and manual range mode In autorange the meter selects the range automatically The meter defaults to autorange when you turn it on In manual range you lock the meter in a range To manually select a range 1 Press RANGE to lock the meter in the present range is displayed 2 Press O RANGE to step through the ranges NOTE The 4000 mV range which can only be entered in manual range is convenient when using accessories 3 return to autorange press RANGE for 2 seconds until is no longer displayed or change the measurement function 10 Users Manual Measuring Voltage 1 2 Insert the test leads in the jacks To select a voltage function put the slide switch in the middle position Figure 3 Press the SELECT button to toggle between dc and ac Touch the probes to the test points and read the display The meter beeps when OL overload is displayed Measuring Voltage Volts DC 11 Volts AC FLUKE 10 MULTIMETER Figure 3 Measuring Voltage acz03f eps 10 Users Manual Testing Continuity An
5. d Measuring Resistance 1 Insert the test leads in the jacks and turn off power to the circuit under test External voltage across the components causes invalid readings 2 Putthe slide switch in the continuity ohms position Figure 4 The meter selects the continuity diode or ohms function Press SELECT to toggle between the continuity diode 11 gt and ohms Q functions 3 Touch the probes to the test points In ohms read the resistance on the display In continuity test the beeper sounds continuously if continuity exists resistance 25 Q Opens and shorts longer than 250 us are detected Turning the Beeper Off To disable beeper functions press and hold down for 2 seconds while turning the meter on 10 Turning the Beeper Off Resistance Continuity Test FLUKE 10 MULTIMETER FLUKE 10 MULTIMETER 4 0501 000 d acz04f eps Figure 4 Continuity Test and Resistance Measurement 11 10 Users Manual Testing Diodes 1 2 12 Insert the test leads in the jacks Put the slide switch in the continuity ohms position The meter selects either the continuity diode ll gt or ohms function If ohms is selected press SELECT to toggle to the continuity diode function To toggle the beeper on or off in continuity diode test press 9 RANGE When the beeper is enabled
6. ght be impaired e Verify the meter s operation by measuring a known voltage e Do not use the meter if the meter or test leads look damaged or if you sus pect that the meter is not operating properly If in doubt have the meter serviced e Replace the battery as soon as the low battery indicator E appears to avoid false readings that can lead to shock and injury e Turn off power to the circuit under test before cutting unsoldering or breaking the circuit Small amounts of current can be dangerous e not apply more than 600 V rms between a terminal and earth ground e Use caution when working above 60 V dc or 30 V ac rms Such voltages pose a shock hazard e Keep your fingers behind the finger guards on the probes when using the probes e Disconnect the live test lead before disconnecting the common test lead Contacting Fluke for Service Accessories or Parts This meter should be serviced only by a qualified service technician To order the 10 Series Service Manual PN 900824 accessories parts or to get other information contact Fluke at one the phone numbers listed below 1 888 993 5853 in USA and Canada 31 402 678 200 in Europe 81 3 3434 0181 Japan 65 738 5655 Singapore 1 425 446 5500 in other countries Visit Fluke s web site at www fluke com Address correspondence to Fluke at Fluke Corporation Fluke Europe B V PO Box 9090 PO Box 1186 Everett Washington 98206 9090 5602 BD Einhoven USA The Nethe
7. received including interference that may cause undesired operation Accuracy is specified for a period of one year after calibration at 18 C to 28 C 64 F to 82 F with relative humidity to 90 AC conversions are ac coupled average responding and calibrated to the rms value of a sine wave input Accuracy Specifications are given as 96 of reading number of least significant digits 15 10 Users Manual Maximum Voltage Between any Terminal and Earth Ground Display Operating Temperature Storage Temperature Temperature Coefficient Relative Humidity Battery Type Battery Life Shock Vibration Size Hx W x L Weight Safety EMI Regulations 16 600 V rms 3 3 4 digits 4000 counts updates 4 sec 10 C to 50 C 30 C to 60 C indefinitely to 40 C for 100 hrs 0 1 x specified accuracy C 18 C or gt 28 0 96 to 90 Yo 10 C to 35 C 0 Yo to 70 Yo 35 C to 50 C 9V NEDA 1604 or IEC 6F22 Alkaline 650 hrs continuous Carbon zinc 450 hrs continuous 1 meter shock Vibration per MIL T 28800D for a Class 3 Instrument 1 35 x 2 75 x 5 55 inches 3 46 x 7 05 x 14 23 cm 10 oz 286 g Complies with Protection Class II requirement of UL1244 ANSI ISA S82 CSA C22 2 No 231 and VDE 0411 and IEC 1010 overvoltage CAT III CAT III instruments are designed to protect against transients in fixed equipment installations at the distribution le
8. rlands 10 Users Manual Replace Battery Digital Reading z RI xp D DL Ui iv Measurement Manual Range L Lj inca 7 Units m gt Continuit Enabled Diode Test Note Before using peel off plastic lens protector starting at any corner acz01f eps Figure 1 Display Standby Mode In Standby mode the display goes blank to preserve battery life The meter beeps and enters Standby if it is LEFT ON BUT IS INACTIVE for more than 45 minutes Press any button to resume operation Operating Features Operating Features Toggle Between Volts DC and AC or Continuity and Ohms Ranging Operations 3 Position Slide Switch Volts DC AC ann Position D Common Return Jack Continuity Diode Test and Ohms Input Jack Figure 2 Operating Features acz02f eps 10 Users Manual Using Accessories When using accessories put the slide switch in the volts position For ease of reading manually select the 4000 mV range In the 4000 mV range 1 mV corresponds to 1 unit being measured by the accessory Symbols A Important Information see manual Diode AC Alternating Current Earth Ground E DC Direct Current Double Insulation VDE Verband Deutscher Electroniker UD Underwriters Laboratories Inc Battery Low Battery on Display B O try Continuity Beeper Using the Autorange
9. vel Complies with FCC Part 15 Class B and VDE 0871B Specifications Function Range Resolution Accuracy 50 to 400 Hz Ve 4000 mV 1mV 2 9 Yo 3 4 000 V 0 001 V 2 9 3 40 00 V 0 01 V 2 9 Yo 3 400 0 V 0 1V 2 9 3 600 V 1V 2 9 Yo 3 V 4000 mV 1mv 1 5 96 2 4 000 V 0 001 V 1 5 2 40 00 V 0 01 V 1 5 96 1 400 0 V 0 1 V 1 5 96 1 600 V 1V 1 5 96 1 Q 400 0 Q 0 10 1 5 Yo 2 4 000 kQ 0 001 kQ 1 5 96 1 40 00 kQ 0 01 kQ 1 5 96 1 400 0 kQ 0 1 KQ 1 5 96 1 4 000 MQ 0 001 MO 1 5 96 1 40 00 MO 0 01 MQ 1 9 Yo 3 n 2 000 V 0 001 V 1 5 96 2 The 4000 mV range can only be entered in manual range mode Use the 4000 mV range with accessories The beeper is guaranteed to come on at 25Q and turn off at 22500 The meter detects opens or shorts of 250 us or longer 17 10 Users Manual Input Common Mode Overload Impedance Rejection Ration Normal Mode Function Protection Nominal 1 kQ Unbalance Rejection V 600 V dc gt 10 MQ lt 100 pF 100 dB dc gt 50 dB 50 Hz or 60 Hz 50 or 60 Hz 50 or 60 Hz V 600 V rms gt 5 MQ lt 100 pF gt 60 dB dc 60 Hz NA ac coupled Q Open Circuit Full Scale Voltage Short Circuit Test Voltage Current To40MO 40 600 V rms lt 1 5 V dc 450 mV dc lt 1 5 lt 500 pA 600 V rms
Download Pdf Manuals
Related Search