Home

PDF

1. 41000C 1000 Ib 37 3 4 78 1 8 8 7 8 x 7 1 8 21 x21 33 5 8 x 33 5 8 ENS PREPARATION Assembly refer to Figure 1 Tools required 1 2 box end wrench 19mm wrench 3 8 hex socket amp torque wrench 1 2 3 Three major parts should be included in the package a Hydraulic unit Assembly b Saddle Assembly c 2 pieces of base half with hardware Attach either one of the two base halves to the base of the hydraulic unit then secure using allen head bolts and washers provided Apply the same procedure to the other base half Use torque wrench to tighten to 30 Ib ft Do not overtighten Place the socket of the saddle assembly onto the ram piston Tighten set screw on the socket Before Use 1 3 Verify that the product and application are compatible if in doubt call Omega Technical Service 888 332 6419 2 Before using this product read the operator s manual completely and familiarize yourself thoroughly with the product its components and recognize the hazards associated with its use Press the release valve pedal ensure that saddle is fully lowered Remove shipping screw and replace with provided vent screw shipping screw is located above the oil filler screw Remove the oil filler screw Ensure oil level is just below the rim of oil filler hole Reinstall the oil filler screw For air option model 41001C pour a teaspoon of good quality air tool lubricant into the air supply inlet of th
2. An off center transmission could cause the jack to tip or flip over Lower saddle Be sure all tools and personnel are clear before lowering load Slowly engage release valve pedal Maintain control of the rate of speed at which the load lowers at all times Slowly gently apply downward pressure to the release valve pedal A Never use this jack as a workstation MAINTENANCE Important Use only good grade hydraulic jack oil Avoid mixing different types of fluid and NEVER use brake fluid turbine oil transmission fluid motor oil or glycerin Improper fluid can cause premature failure of the jack and the potential for sudden and immediate loss of load Mobil DTE 13M or equivalent recommended Adding oil 1 With saddle fully lowered set jack in its upright level position Remove oil filler screw 2 Fill until oil is level with the oil filler screw hole reinstall oil filler screw Changing oil For best performance and longest life replace the complete fluid supply at least once per year 1 With saddle fully lowered remove oil filler screw 2 Lay the jack on its side and drain the fluid into a suitable container Note Dispose of hydraulic fluid in accordance with local regulations 3 Set jack in its level position Fill until oil is level with the oil filler screw hole reinstall oil filler screw Lubrication 1 Aperiodic coating of light lubricating oil to pivot points axles and hinges will help to prevent rust and assure
3. 8 00120 000 Copper Washer 41001C only 26 G390 41000 000 Nylon Strap Assy N 1 17 G390 30000 000 Lift Pedal 2 7 0 23 24 25 Repair Kit Contents 32 Backup Washer Jo Psa fors o aa foras o JCC E ps6 orig 37 Backup Washer Jo Paz sea as sea Laa Backup Washer Ja 45 Backup Washer o G36018 111 410000 ne G3600S 130 41001C 58 49 P ONE YEAR LIMITED WARRANTY For a period of one 1 year from date of purchase SFA Companies will repair or replace at its option without charge any of its products which fails due to a defect in material or workmanship under normal usage This limited warranty is a consumer s exclusive remedy Performance of any obligation under this warranty may be obtained by returning the warranted product freight prepaid to SFA Companies Warranty Service Department 10939 N Pomona Ave Kansas City MO 64153 Except where such limitations and exclusions are specifically prohibited by applicable law 1 THE CONSUMER S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE 2 SFA Companies SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER 3 ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO ONE YEAR OTHERWISE THE REPAIR REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS T
4. HE EXCLUSIVE REMEDY OF THE CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED 4 ANY MODIFICATION ALTERATION ABUSE UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND IS NOT COVERED BY THIS WARRANTY Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state SFA Companies e 10939 N Pomona Ave Kansas City MO 64153 ESA 888 332 6419 Noe sales omegalift com
5. Operating Instructions Manual OMEGA NS Hydraulic Transmission Jack Telescopic Model Capacity 41000C 1000 Ib 41001C air option 2 y Model 41001C e U S Patent No 5 341 723 a o A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death e Leer comprender y seguir las instrucci nes antes To avoid crushing and related injuries de utilizar el aparato m7 4 NEVER work on under or around a e El manual de instrucci nes y la informaci n de load supported only by a hydraulic seguridad deben estar comunicado en lengua del jack Immediately transfer the load to operador antes del uso an appropriate work station e No seguir estas indicaci nes puede causar da os personales o materiales SFA Companies http www omegalift com Read this manual and follow all the Safety Rules and Operating Instructions before using this product Printed in China 41000C M2 10 10 SAFETY AND GENERAL INFORMATION Save these instructions For your safety read understand and follow the information provided with and on this jack before using The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use The owner and operator shall be aware that use and repair of this product m
6. ay require special skills and knowledge Instructions and safety information shall be conveyed in the operator s native language before use of this jack is authorized If any doubt exists as to the safe and proper use of this jack remove from service immediately Inspect before each use Do not use if broken bent cracked or damaged parts are noted Any jack that appears damaged in any way or operates abnormally shall be removed from service immediately If the jack has been or suspected to have been subjected to a shock load a load dropped suddenly unexpectedly upon it immediately discontinue use until jack has been checked by a factory authorized service center contact distributor or manufacturer for list of authorized service centers It is recommended that an annual inspection be done by qualified personnel Labels and Operator s Manuals are available from manufacturer PRODUCT DESCRIPTION Hydraulic Transmission Jack is designed to be used as an aid in the removal and installation of automotive and light truck transmissions transfer cases and transaxles This telescopic style transmission jack is for use under an overhead lift or in a garage pit On air option model 41001C ensure that your air source can dedicate 7 8 CFM 110 175 psi to each jack operated A NEVER use for any purpose other than those uses outlined above SPECIFICATIONS Min Max Extended Jack Size Capacity Height Height 99de Base saddle Area L x W
7. e lift control valve Connect to air supply and operate for 3 seconds to evenly distribute lubricant Note This unit is equipped with the popular 1 4 NPT air coupler When installing a different air coupler of your choice ensure that thread tape or compound is used when servicing connections To ensure dependable trouble free operation an inline air dryer and oiler is recommended Ensure that jack rolls freely Raise and lower the unloaded jack throughout the lifting range before putting into service to ensure the pump operates smoothly Replace worn or damaged parts and assemblies with Omega authorized replacement parts only Saddle Plate Saddle Socket o os A Bracket Tilt Adjustment Knobs Shipping Screw replace w Vent Screw Hydraulic Unit before initial use Position Handle _____ Oil Filler Screw Air Pump Pedal Lift Pedal Ni NS Air Supply Inlet Air Motor Caster Release Valve Pedal Base Half For air option model 41001C only i 8 Figure 1 Typical Transmission Jack Components 41001C shown 3 Read understand and follow all printed material provided with and on this product before use Do not exceed rated capacity e Use only on hard level surfaces Adequately support the vehicle before starting repairs If loaded jack must be moved make certain that load is secured by appropriate means is stable is in th
8. e lowest possible position is moved over a smooth hard level surface and that the lifting platform is level e Use of this product is limited to removal installation and transportation of automotive and light truck transmissions transfer cases and transaxles e Use only adapters accessories provided by the manufacturer of this transmission jack e Use only adapters accessories whose rated capacity is greater than the rated capacity of this jack e Ensure the center of gravity is center loaded on the saddle e Never use this device as a work repair station Transfer the load immediately to a suitable work station e No alteration shall be made to this product e Failure to heed these markings may result in personal injury and or property damage To avoid crushing and related injuries e Never work on under or around a load supported only by hydraulic jack e Be alert and sober when using this product Do not operate under the influence of drugs or alcohol OPERATION Follow the instruction for removal and installation of transmission transfer case or transaxle according to the vehicle manufacturer s service manual Raise saddle assembly Pump foot pedal or press air pump pedal Model 41001C until saddle reaches desired position Secure load with provided chains Note DO NOT OPERATE BY AIR AND BY HAND PUMPING AT THE SAME TIME Ensure center gravity of load is centered on the saddle and load is stable before moving jack
9. that casters and pump assemblies move freely 2 For air option models 41001C When used on a daily basis air pump model should be internally lubricated before each use Use only good quality air tool lubricant If no inline oiler is used pour a teaspoon of air tool oil into the inlet of the air supply inlet Simply operate the jack using the air feature in order to fully distribute the oil Cleaning Periodically check the pump piston and ram for signs of rust or corrosion Clean as needed and wipe with an oily cloth Note Never use sandpaper or abrasive material on these surfaces Storage When not in use store the jack with saddle fully lowered eee ar Symptom ptom PossibleCauses Causes CorrectiveAction Action Jack will not lift load e Release valve not tightly closed e Ensure release valve tightly closed e Load is too heavy e Consider higher capacity jack Jack will lift but not maintain e Release valve not tightly closed Ensure release valve tightly closed pressure e Hydraulic unit malfunction e Discontinue use Contact Omega Tech Service Jack will not lower after unloading Reservoir overfilled Ensure load is removed then drain fluid to proper level e Linkage binding e Clean and lubricate moving parts Poor lift performance e Fluid level low Ensure proper fluid level e Hydraulic unit malfunction e Discontinue use Contact Omega Tech Service Jack will not lift to full extension e Fluid level low e Ens
10. ure proper fluid level REPLACEMENT PARTS page 6 amp 7 Not all components of the jack are replacement items but are illustrated as a convenient reference of location and position in the assembly sequence When ordering parts please give the Model number and parts description Call or write for current pricing SFA Companies 10939 N Pomona Ave Kansas City MO 64153 U S A E Mail sales omegalift com Tel 888 332 6419 Fax 816 891 6599 Website http www omegalift com Replacement Parts Illustration for Models 41000C and 41001C E eee a A 41000C Replacement CA Parts j 41001C Replacement Parts Replacement Parts List for Models 41000C amp 41001C i Tilt Screw Assy N G360 40000 000 Saddle Head Assembly 2 5104 10040 000 Bolt A070 90038 K02 Screw Assembly G360 90009 K01 Vent Screw Assembly G390 20000 000 Handle Assembly G251 00007 000 Handle Grip 13 5206 00010 000 Nylon Nut Release Valve Pedal 2pc 14 G390 10005 000 for 41001C 15 5405 07027 000 Pin 2pc for 41001C al Retaining Pin 2pc for 6 5405 02018 000 41001C 5405 02028 000 Retaining Pin Coupler Male 1 4NPT G831 00002 000 41001C only oO 1 BE G360 10003 000 Air Hose 41001C only 2 G360 10002 000 Spring 41001C only Hose Connector Elbow G360 16000 000 41001C only G360 17000 000 Air Motor 41001C only 530

PDF

Contents

Download Pdf Manuals

Related Search

Related Contents