Sun StorEdge Expansion Cabinet Installation and Service Manual
Contents
1. Key switch Standby OS FIGURE 2 1 Location of Key Switch on Bottom Front Panel Front trim panel 2 1 2 Open the rear door of the expansion cabinet FIGURE 2 2 DD ____N Z DD DD DT LD CD FIGURE 2 2 Opening the Rear Door of the Expansion Cabinet 3 Loosen the four screws on the front and rear trim panels and remove the panels Set the panels aside 2 2 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 2 Connecting the AC Power Cord Caution The expansion cabinet is designed to work with single phase power systems that have a grounded neutral conductor To reduce the risk of electric shock do not connect the expansion cabinet into any other type of power system Open the rear door FIGURE 2 2 Verify that each AC power sequencer circuit breaker is in the Off position and the Local Remote switch is in the Local position FIGURE 2 3 Fan fail Fan fail cable out cable in Power Off ao iy 3 20 o o E SEP 80 Grounding S 58 5 screw E a o eS i 3 5 y wv 5 a E 5 E S 7 Img O O 26 E 3 Ol 6 ES lt zaoOozuwue 2 Local Remote switch Power On AC power sequencer circuit breaker FIGURE 2 3 Power Sequencer Control Panel Chapter 2 Cabl2. A 2 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 A 4 Electrical Specifications TABLE A 3 Cabinet Power Sequencer Electrical Specifications Parameter Value s AC voltage rating AC voltage range 200 to 240 VAC 180 to 264 VAC Frequency range 47 to 63 Hz Current at 240 VAC 24A Power consumption maximum 5 4 kW A 5 Environmental Requirements TABLE A 4 Operating Environment Parameter Value Temperature Operating 5 C to 35 C 41 F to 95 F Non operating 40 C to 66 C 40 F to 150 8 F Humidity Operating 20 to 80 RH noncondensing Non operating Altitude Operating Non operating Ventilation 27 C 80 6 F maximum wet bulb 5 to 95 RH noncondensing 0 to 9 843 feet 0 to 3 km 0 to 39 370 feet 0 to 12 km Well ventilated or air conditioned Appendix A Product Specifications A 3 A 6 Operating Environment A 4 Avoid temperature extremes and keep the work area clean Maintain the operating conditions described in TABLE A 4 The expansion cabinet should be in a computer room environment Computer room installation provides secure access to computers and stored information and provides control over environmental factors such as temperature humidity and airborne dust Computer room installation can also help protect equipment from fire flood or other danger originating in the building Sun StorEdge Expansion Cabinet Installation an
3. Wartezustand Stand by Position Der Ein Wartezustand Schalter steht auf Wartezustand nderungen an Sun Ger ten Nehmen Sie keine mechanischen oder elektrischen nderungen an den Ger ten vor Sun Microsystems bernimmt bei einem Sun Produkt das ge ndert wurde keine Verantwortung f r die Einhaltung beh rdlicher Vorschriften Aufstellung von Sun Ger ten Achtung Um den zuverl ssigen Betrieb Ihres Sun Ger ts zu gew hrleisten und es vor berhitzung zu sch tzen d rfen die ffnungen im Ger t nicht blockiert oder verdeckt werden Sun Produkte sollten niemals in der N he von Heizk rpern oder Heizluftklappen aufgestellt werden Einhaltung der SELV Richtlinien Die Sicherung der I O Verbindungen entspricht den Anforderungen der SELV Spezifikation Anschlu des Netzkabels Achtung Sun Produkte sind f r den Betrieb an Einphasen Stromnetzen mit geerdetem Nulleiter vorgesehen Um die Stromschlaggefahr zu reduzieren schlie en Sie Sun Produkte nicht an andere Stromquellen an Ihr Betriebsleiter oder ein qualifizierter Elektriker kann Ihnen die Daten zur Stromversorgung in Ihrem Geb ude geben Achtung Nicht alle Netzkabel haben die gleichen Nennwerte Herk mmliche im Haushalt verwendete Verl ngerungskabel besitzen keinen berlastungsschutz und sind daher f r Computersysteme nicht geeignet Netzkabel f r geerdete Netzsteckdosen geliefert Um die Gefahr eines Stromschlags
4. on page 3 4 2 Disconnect the key switch adapter cable from the mating power supply connector at the rear of the power sequencer FIGURE 5 4 FIGURE 5 4 Power Sequencer 3 Remove the AC power cord from the power sequencer See Section 5 3 AC Input Cable Assembly on page 5 4 4 Remove the screws that secure the sequencer to the chassis 5 Slide out the power sequencer to access the power cables 6 Disconnect all other power cables from the sequencer 7 Remove the power sequencer 5 6 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 To replace the power sequencer Place the power sequencer on the floor Connect all cables on the back of the power sequencer Slide the power sequencer into the expansion cabinet FIGURE 5 4 Tighten the screws that secure the sequencer to the chassis Connect the AC power cord See Section 5 3 AC Input Cable Assembly on page 5 4 Power on the expansion cabinet See Chapter 3 Chapter 5 Cabinet Subassemblies 5 7 5 8 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 APPENDIX A Product Specifications A 1 Physical Characteristics The physical characteristics of the expansion cabinet are as follows m Internal dimensions conform to EIA RS 310C standard RETMA for 19 inch 482 mm racks Universal mounting holes are used with 10 32UNF tapped holes in all locations The nominal rack
5. 805 7687 806 0274 Accessing Sun Documentation Online The docs sun com web site enables you to access Sun technical documentation on the Web You can browse the docs sun com archive or search for a specific book title or subject at http docs sun com Ordering Sun Documentation Fatbrain com an Internet professional bookstore stocks select product documentation from Sun Microsystems Inc For a list of documents and how to order them visit the Sun Documentation Center on Fatbrain com at http www fatbrain com documentation sun xiii Sun Welcomes Your Comments Sun is interested in improving its documentation and welcomes your comments and suggestions You can email your comments to Sun at docfeedback sun com Please include the part number 805 3067 14 of your document in the subject line of your email xiv Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 CHAPTER 1 Installing the Expansion Cabinet This chapter describes how to unpack and install the expansion cabinet 1 1 Features The expansion cabinet contains the following m Two power sequencer assemblies m Four floor mounting brackets m Two stabilizer legs m Associated mounting hardware The floor mounting brackets enable you to bolt the expansion cabinet to the floor If you will not be installing the floor mounting brackets you should install the stabilizer legs The stabilizer legs are
6. Tilt the door and insert the bottom hinge pin with outside hole of the bottom left mounting bracket b Reach inside of the door and push down on the lever attached to the spring of the top hinge pin This will cause the hinge pin to retract into the door c Align the top hinge pin with the outside hole of the top left mounting bracket d Release the lever The hinge pin will extend into the mounting bracket 4 4 Removing a Device These instructions are meant to be used in conjunction with those that shipped with the device you are installing Read both procedures before beginning the installation Note If you are told to remove the side panels in the instructions that came with your device also perform the steps in Section 4 5 Side Panel Removal and Replacement on page 4 7 For cabinets equipped with a front screen door open the front screen door If you want to remove the door a Reach inside of the door and push down on the lever attached to the spring of the top hinge pin This will cause the hinge pin to retract into the door Chapter 4 Installing and Removing Devices 4 5 4 6 b Tilt the door out from the top mounting bracket c Remove the door and set it aside Remove the trim strips beside the device FIGURE 4 1 Use a 2 Phillips screwdriver and loosen the captive screws that fasten the trim strips to the rack Remove the trim strips and save for future use If the exp
7. 2000 CHAPTER 3 Powering On and Off Use the information provided in this chapter to power on and off the expansion cabinet Caution To avoid damage to internal circuits do not connect or disconnect any cable while the system is powered on 3 1 Powering On the Expansion Cabinet 1 Verify that the key switch located at the bottom front of the expansion cabinet is in the Standby position FIGURE 3 1 Key switch Standby er Ox FIGURE 3 1 Location of Key Switch on Bottom Front Panel 3 1 2 Turn the AC power sequencer circuit breakers at the bottom front and bottom rear 4 5 of the cabinet to Off FIGURE 3 2 Power Off ao u gt Q 20 o o z eCe E 20 Grounding o 53 59 screw y 5 ao o y JR 5 E z D E SO o o o 5 Ol 6 E lt zaoozuwuer 2 Local Remote switch Power On AC power sequencer circuit breaker FIGURE 3 2 AC Power Sequencer Control Panel Verify that the cabinet AC power cord is connected to an AC outlet Caution Do not disconnect the AC power cord from the outlet when you work on or in the cabinet This connection provides a ground path that prevents damage from electrostatic discharge Caution Never move the system or expansion cabinets when system power is on Excessive movement can cause catastrophic disk drive failure Always power the s
8. Your local recycling authority can supply specific information 1 2 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 1 3 Moving and Placing the Cabinet Leave enough space to situate the expansion cabinet near the system cabinet The ground strap between the expansion cabinet and the system cabinet is 2 meters long The procedure for connecting the ground strap is covered in detail in Section 2 3 Connecting the Ground Strap on page 2 6 Refer to the specifications in Appendix A Product Specifications when you are determining where to place the expansion cabinet Caution Never lift the expansion cabinet by the cosmetic panel surfaces or pull by the rear door Use three or more people to move the expansion cabinet safely Two people must restrain the front of the expansion cabinet to control the movement One person should be behind the expansion cabinet To prevent the expansion cabinet from tipping as you move it push or pull only on the middle section of the expansion cabinet For mobility allow 3 inches 76 mm clearance on both sides of the expansion cabinet Chapter 1 Installing the Expansion Cabinet 1 3 1 4 1 4 Adjusting the Leveling Pads Skip to Section 1 6 Installing the Floor Brackets on page 1 7 if you are installing the floor mounting brackets Leveling pads screws are located at each corner of the base of the expansion cabinet FIGURE 1 1 Cautio
9. cabinet 1 Loosen the securing screw on the right stabilizer leg FIGURE 1 2 Left A d Right stabilizer leg Securing screw A T FIGURE 1 2 Stabilizer Legs Chapter 1 Installing the Expansion Cabinet 1 5 2 Slide the right stabilizer leg over the three mounting screws at the bottom of the expansion cabinet FIGURE 1 3 Mounting screws FIGURE 1 3 Installing the Right Stabilizer Leg 3 Tighten the securing screw This prevents the stabilizer leg from falling off the mounting screws when it is extended 4 Fully extend the right stabilizer leg 5 Repeat Step 1 through Step 4 for the left stabilizer leg 6 Use the leveling wrench and adjust the feet on both stabilizer legs so that they touch the ground FIGURE 1 4 FIGURE 1 4 Adjusting The Leveling Pads on the Stabilizer Leg 1 6 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 7 Slide both stabilizer legs under the expansion cabinet 8 Secure the leveling wrench inside the expansion cabinet 9 Close the door Installing the Floor Brackets Skip this section if you have installed the stabilizer legs The four floor brackets are used in place of the stabilizer legs when you want to attach the expansion cabinet to the floor Caution Do not bolt the floor mounting brackets to the deck plating of a raised computer floor Note If you are installing the floor brackets over previousl
10. extended to prevent the expansion cabinet from tipping over when devices are installed removed or serviced 1 2 Unpacking the Cabinet If the expansion cabinet is already unpacked proceed to the Section 1 3 Moving and Placing the Cabinet on page 1 3 Inspect all shipping containers for evidence of physical damage If a shipping carton is damaged request that the carrier s agent be present when the carton is opened Keep all of the contents and packing material for the agent s inspection Caution Use three or more people to unpack and set up the expansion cabinet The shipping weight of the unit varies depending on the number of devices that are shipped with the unit A typical expansion cabinet can weigh from 500 to 1100 pounds 226 kg to 499 kg Unpack the expansion cabinet Refer to the unpacking instructions printed on the shipping carton Note The stabilizer legs floor mounting brackets and associated hardware are packed in the side saddles of the packing material that encase the expansion cabinet Verify that the components you received match the shipping list Reassemble the packing materials and save them for future use To prepare the expansion cabinet for shipment or storage follow in reverse order the unpacking instructions attached to or printed on the panels of each shipping container If you cannot store the shipping materials recycle or dispose of the materials properly
11. otro tipo de sistema de alimentaci n el ctrica P ngase en contacto con el responsable de mantenimiento o con un electricista cualificado si no est seguro del sistema de alimentaci n el ctrica del que se dispone en su edificio Precauci n No todos los cables de alimentaci n AN el ctrica tienen la misma capacidad Los cables de tipo dom stico no est n provistos de protecciones contra sobrecargas y por tanto no son apropiados para su uso con computadores No utilice alargadores de tipo dom stico para conectar sus productos Sun cable de alimentaci n con toma de tierra Para reducir el riesgo de descargas el ctricas con ctelo siempre a un enchufe con toma de tierra Precauci n Con el producto Sun se proporciona un La siguiente advertencia se aplica solamente a equipos con un interruptor de encendido que tenga una posici n En espera producto funciona exclusivamente como un dispositivo de puesta en espera El enchufe de la fuente de alimentaci n est dise ado para ser el elemento primario de desconexi n del equipo El equipo debe instalarse cerca del enchufe de forma que este ltimo pueda ser f cil y r pidamente accesible No conecte el cable de alimentaci n cuando se ha retirado la fuente de alimentaci n del chasis del sistema A Precauci n El interruptor de encendido de este Caution Attention Achtung Precauci n Caution The equipment relies on the protection d
12. peut tre reproduite sous aucune forme par quelque moyen que ce soit sans Vautorisation pr alable et crite de Sun et de ses bailleurs de licence s il y en a Le logiciel d tenu par des tiers et qui comprend la technologie relative aux polices de caracteres est prot g par un copyright et licenci par des fournisseurs de Sun Des parties de ce produit pourront tre d riv es des syst mes Berkeley BSD licenci s par Universit de Californie UNIX est une marque d pos e aux Etats Unis et dans d autres pays et licenci e exclusivement par X Open Company Ltd La notice suivante est applicable Netscape Communicator M Copyright 1995 Netscape Communications Corporation Tous droits r serv s Sun Sun Microsystems the Sun logo AnswerBook2 docs sun com StorEdge et Solaris sont des marques de fabrique ou des marques d pos es ou marques de service de Sun Microsystems Inc aux Etats Unis et dans d autres pays Toutes les marques SPARC sont utilis es sous licence et sont des marques de fabrique ou des marques d pos es de SPARC International Inc aux Etats Unis et dans d autres pays Les produits portant les marques SPARC sont bas s sur une architecture d velopp e par Sun Microsystems Inc L interface d utilisation graphique OPEN LOOK et Sun a t d velopp e par Sun Microsystems Inc pour ses utilisateurs et licenci s Sun reconna t les efforts de pionniers de Xerox pour la recherche et le d veloppement du concept
13. short circuit that could cause fire electric shock or damage to your equipment Symbols The following symbols may appear in this book Caution There is risk of personal injury and equipment damage Follow the instructions Caution Hot surface Avoid contact Surfaces are hot and may cause personal injury if touched Caution Hazardous voltages are present To reduce the risk of electric shock and danger to personal health follow the instructions On Applies AC power to the system Depending on the type of power switch your device has one of the following symbols may be used Off Removes AC power from the system Standby The On Standby switch is in the standby position Modifications to Equipment Do not make mechanical or electrical modifications to the equipment Sun Microsystems is not responsible for regulatory compliance of a modified Sun product Placement of a Sun Product Caution Do not block or cover the openings of your Sun product Never place a Sun product near a radiator or heat register Failure to follow these guidelines can cause overheating and affect the reliability of your Sun product SELV Compliance Safety status of I O connections comply to SELV requirements Power Cord Connection Caution Sun products are designed to work with single phase power systems having a grounded neutral conductor To reduce the risk of elect
14. the Standby position FIGURE 3 1 At the bottom of the expansion cabinet remove the trim panels and turn the AC power sequencer circuit breakers to Off FIGURE 3 2 If you are servicing components other than disk or tape drives such as the power sequencer disconnect the cabinet power cords from the grounded outlets Caution When you service disk or tape drives do not disconnect the power cords from the power sequencer in the cabinet or the cabinet s power cord from the outlet These connections provide the ground paths necessary to prevent any damage caused by electrostatic discharge to the drives installed in the cabinet Caution You must disconnect the power cables to both power sequencers if you want to stop all AC power input to the expansion cabinet 3 4 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 CHAPTER 4 Installing and Removing Devices This chapter explains how to install and remove devices in the expansion cabinet Caution Storage device systems in the rack must be loaded from the bottom to the top to keep the rack center of gravity as low as possible When servicing the rack remove only one storage device system from the rack at a time If possible remove systems from top to bottom to prevent raising the center of gravity of the rack Use extra caution when moving the rack onto ramps 4 1 Rackmount Placement Rackmount placement informati
15. the U S and other countries Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems Inc The OPEN LOOK and Sun Graphical User Interface was developed by Sun Microsystems Inc for its users and licensees Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry Sun holds a non exclusive license from Xerox to the Xerox Graphical User Interface which license also covers Sun s licensees who implement OPEN LOOK GUIs and otherwise comply with Sun s written license agreements RESTRICTED RIGHTS Use duplication or disclosure by the U S Government is subject to restrictions of FAR 52 227 14 g 2 6 87 and FAR 52 227 19 6 87 or DFAR 252 227 7015 b 6 95 and DFAR 227 7202 3 a DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS REPRESENTATIONS AND WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT ARE DISCLAIMED EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID Copyright 2000 Sun Microsystems Inc 901 San Antonio Road Palo Alto CA 94303 4900 Etats Unis Tous droits r serv s Ce produit ou document est prot g par un copyright et distribu avec des licences qui en restreignent l utilisation la copie la distribution et la d compilation Aucune partie de ce produit ou document ne
16. the device to the power sequencer s An expansion cabinet that is ordered without any devices installed has the power cables routed as shown in FIGURE 4 2 L9 L11 L8 L10 L7 L6 L5 L4 L3 L2 L1 AN N N R9 N R11 N R8 R6 R8 amp R10 R4 R9811 o R10 h R7 siete Oog pog bOol Front sequencer R6 q 563 k R5 R1 amp R2 R7 R3 R5 N R4 P L6 L8 amp L10 L4 L98L11 NI R3 H R2 Rear Log Log Bodo foo sequencer Log pog pog pog R1 Rear view u L18L2 L7 L3 L5 FIGURE 4 2 Power Cable Routing Caution Power cable routing can vary depending on how the expansion cabinet is configured in the factory for instance the power cabling in a StorEdge A3500 1x8 expansion cabinet is different than that in a expansion cabinet configured with StorEdge A5000 disk arrays Refer to the documentation that shipped with your device 4 4 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 9 10 11 Install the trim strips FIGURE 4 1 Use a 2 Phillips screwdriver to tighten the captive screws If necessary retract the stabilizer legs under the cabinet If necessary close the front screen door If you formerly removed the door a
17. zu reduzieren schlie en Sie das Kabel nur an eine fachgerecht verlegte geerdete Steckdose an Achtung Ihr Sun Ger t wird mit einem dreiadrigen iv Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 Die folgende Warnung gilt nur f r Ger te mit Wartezustand Netzschalter schaltet nur auf Wartezustand Stand By Modus Um die Stromzufuhr zum Ger t vollst ndig zu unterbrechen m ssen Sie das Netzkabel von der Steckdose abziehen Schlie en Sie den Stecker des Netzkabels an eine in der N he befindliche frei zug ngliche geerdete Netzsteckdose an Schlie en Sie das Netzkabel nicht an wenn das Netzteil aus der Systemeinheit entfernt wurde Achtung Der Ein Aus Schalter dieses Ger ts Conformit aux normes de s curit Ce texte traite des mesures de s curit qu il convient de prendre pour l installation d un produit Sun Microsystems Mesures de s curit Pour votre protection veuillez prendre les pr cautions suivantes pendant l installation du mat riel e Suivre tous les avertissements et toutes les instructions inscrites sur le mat riel e V rifier que la tension et la fr quence de la source d alimentation lectrique correspondent la tension et la fr quence indiqu es sur l tiquette de classification de l appareil e Ne jamais introduire d objets quels qu ils soient dans une des ouvertures de l appareil Vous pourriez vous trouver en pr sence de haut
18. Cabling the Expansion Cabinet 2 5 Caution The expansion cabinet has a high leakage current to ground Strictly observe all caution and note statements to reduce the risk of electric shock Note If the appropriate mating receptacle is not available the connector may be removed from the cord The cord may then be permanently connected to a dedicated branch circuit by a qualified electrician Check local electrical codes for proper installation requirements Note Cable ties provided with the expansion cabinet can be used as cable restraints For each cable pass a cable tie through one of the slits located along the base of the cabinet Secure the cable in the cable tie Repeat this procedure for the other power sequencer 23 Connecting the Ground Strap Caution The installer must install an insulated grounding conductor as part of the circuit supplying power to the unit or system This conductor must be of identical size insulation material and thickness to the neutral grounded and hot ungrounded branch circuit supply conductors but green with or without yellow stripels The grounding conductor described in the above caution statement must be grounded to either of the following m Earth at service equipment Supply transformer or motor generator set if supplied by a separately derived system The outlets in the vicinity of the unit must be of the grounding type and the grounding conductors for these o
19. Ss amp Sun microsystems Sun StorEdge Expansion Cabinet Installation and Service Manual Sun Microsystems Inc 901 San Antonio Road Palo Alto CA 94303 4900 U S A 650 960 1300 Part No 805 3067 14 July 2000 Revision A Send comments about this document to docfeedback sun com Copyright 2000 Sun Microsystems Inc 901 San Antonio Road Palo Alto CA 94303 4900 USA All rights reserved This product or document is protected by copyright and distributed under licenses restricting its use copying distribution and decompilation No part of this product or document may be reproduced in any form by any means without prior written authorization of Sun and its licensors ifany Third party software including font technology is copyrighted and licensed from Sun suppliers Parts of the product may be derived from Berkeley BSD systems licensed from the University of California UNIX is a registered trademark in the U S and other countries exclusively licensed through X Open Company Ltd For Netscape Communicator the following notice applies Copyright 1995 Netscape Communications Corporation All rights reserved Sun Sun Microsystems the Sun logo AnswerBook2 docs sun com StorEdge and Solaris are trademarks registered trademarks or service marks of Sun Microsystems Inc in the U S and other countries All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International Inc in
20. abinet See the software documentation for more information After power is turned on several events occur m The system will make a beep sound indicating that the system is ready a The terminal screen will illuminate once the internal self test has been completed You may need to edit the configuration file for your devices See the documentation for the particular device and the Solaris Handbook for Sun Peripherals for software instructions Chapter 3 Powering On and Off 3 3 iZ A Powering Off the Expansion Cabinet Before you turn off the power to the expansion cabinet you must halt any 1 0 between host system s and devices in the expansion cabinet Depending upon the type of devices in the cabinet the type of host system s and the software running on the host system s you may need to m Stop software from accessing devices in the enclosure m Exit the Solaris operating environment m Turn off power to your host system s Refer to the following for specific instructions Solaris Handbook for Sun Peripherals System administration guides that correspond to your operating system Documentation that came with the devices Documentation that came with your host system s Caution Failure to stop I O between host system s and devices in the expansion cabinet can result in the loss of data Stop I O to devices in the expansion cabinet Turn the key switch located at the front of the cabinet to
21. acement 4 7 4 5 1 Removing the Side Panel 4 7 4 5 2 Replacing the Side Panel 4 8 Troubleshooting the Cabinet 4 8 5 Cabinet Subassemblies 5 1 5 1 5 2 5 3 5 4 Tools Required 5 1 Key Switch 5 2 AC Input Cable Assembly 5 4 Power Sequencer 5 6 A Product Specifications A 1 A l A 2 A 3 A 4 A 5 A 6 Physical Characteristics A 1 Physical Specifications A 2 Clearance and Service Access A 2 Electrical Specifications A 3 Environmental Requirements A 3 Operating Environment A 4 B Parts Table B 1 x Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 Preface The StorEdge Expansion Cabinet Installation and Service Manual provides procedures for unpacking and installing the Sun StorEdge Expansion Cabinet It also includes procedures to remove and replace the field replaceable subassemblies in the expansion cabinet Only a qualified service provider should perform the tasks in this manual Note This manual does not cover the installation procedures for storage devices To install storage devices in the expansion cabinet refer to the documentation shipped with the storage device Using UNIX Commands This document does not contain information on basic UNIX commands and procedures such as shutting down the system booting the system and configuring devices See one or more of the following for this information m Solaris Handbook for Sun Peripherals m AnswerBook online do
22. ansion cabinet is not bolted to the floor extend the stabilizer legs The stabilizer legs are located under the front of the cabinet Caution Only extend or retract the stabilizer legs as a pair Be sure that the levelers have been adjusted before attempting to move the stabilizer legs Remove the device Refer to the online Rackmount Placement Matrix and the documentation that came with your device If you will not be reinstalling the device install a filler panel over its previous location FIGURE 4 1 Use a Phillips screwdriver to tighten the captive screws Note To maintain proper airflow filler panels must be installed over locations that do not have devices mounted If necessary retract the stabilizers under the cabinet If necessary close the front screen door If you formerly removed the door a Tilt the door and insert the bottom hinge pin with outside hole of the bottom left mounting bracket b Reach inside of the door and push down on the lever attached to the spring of the top hinge pin This will cause the hinge pin to retract into the door c Align the top hinge pin with the outside hole of the top left mounting bracket d Release the lever The hinge pin will extend into the mounting bracket Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 4 5 Side Panel Removal and Replacement 4 5 1 Removing the Side Panel e Use an Allen wrench to l
23. cumentation for the Solaris software environment m Other software documentation that you received with your system xi Typographic Conventions TABLEP 1 Typographic Conventions Typeface Meaning Examples AaBbCc123 The names of commands files and directories on screen computer output AaBbCc123 What you type when contrasted with on screen computer output AaBbCc123 Book titles new words or terms words to be emphasized Command line variable replace with a real name or value Shell Prompts TABLE P 2 Shell Prompts Edit your login file Use 1s a to list all files o You have mail oe su Password Read Chapter 6 in the User s Guide These are called class options You must be superuser to do this To delete a file type rm filename Shell C shell C shell superuser Bourne shell and Korn shell Bourne shell and Korn shell superuser Prompt machine_name machine_name xii Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 Related Documentation TABLE P 3 Related Documentation Title Part Number Sun StorEdge A3500 Hardware Configuration Guide Sun StorEdge A5000 Tasks and Documentation Guide Sun StorEdge D1000 and A1000 Rackmount Installation Guide Sun StorEdge Expansion Cabinet Installation Guide for the Sun Enterprise 4x00 Sun StorEdge Expansion Cabinet Airflow Baffle Installation Guide 805 4981 805 1903 805 2626
24. d Service Manual July 2000 APPENDIX B Parts Table The following parts of the expansion cabinet can be replaced at a customer site by a qualified field service engineer TABLE B 1 Field Replaceable Unit FRU List FRU List Parts Power sequencer universal rack Assembly cable rack AC input international Assembly cable rack AC input domestic Assembly cable universal power cord Assembly cable main rack to expansion interface Key switch panel assembly Filler panel and trim strip kit Part Number 300 1393 530 2675 530 2674 530 2197 530 2236 540 3804 595 4853 Note The suffix xx denotes the revision level of an assembly B 2 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000
25. des interfaces d utilisation visuelle ou graphique pour l industrie de l informatique Sun d tient une licence non exclusive de Xerox sur l interface d utilisation graphique Xerox cette licence couvrant galement les licenci s de Sun qui mettent en place l interface d utilisation graphique OPEN LOOK et qui en outre se conforment aux licences crites de Sun CETTE PUBLICATION EST FOURNIE EN L ETAT ET AUCUNE GARANTIE EXPRESSE OU IMPLICITE N EST ACCORDEE Y COMPRIS DES GARANTIES CONCERNANT LA VALEUR MARCHANDE L APTITUDE DE LA PUBLICATION A REPONDRE A UNE UTILISATION PARTICULIERE OU LE FAIT QU ELLE NE SOIT PAS CONTREFAISANTE DE PRODUIT DE TIERS CE DENI DE GARANTIE NE S APPLIQUERAIT PAS DANS LA MESURE OU IL SERAIT TENU JURIDIQUEMENT NUL ET NON AVENU GS tem Ca Adobe PostScript Safety Agency Compliance Statements Read this section before beginning any procedure The following text provides safety precautions to follow when installing a Sun Microsystems product Safety Precautions For your protection observe the following safety precautions when setting up your equipment e Follow all cautions and instructions marked on the equipment e Ensure that the voltage and frequency of your power source match the voltage and frequency inscribed on the equipment s electrical rating label e Never push objects of any kind through openings in the equipment Dangerous voltages may be present Conductive foreign objects could produce a
26. entation de ce produit fonctionne comme un dispositif de mise en veille uniquement C est la prise d alimentation qui sert mettre le produit hors tension Veillez donc installer le produit proximit d une prise murale facilement accessible Ne connectez pas la prise d alimentation lorsque le ch ssis du syst me n est plus aliment Normativas de seguridad El siguiente texto incluye las medidas de seguridad que se deben seguir cuando se instale alg n producto de Sun Microsystems Precauciones de seguridad Para su protecci n observe las siguientes medidas de seguridad cuando manipule su equipo e Siga todas los avisos e instrucciones marcados en el equipo e Aseg rese de que el voltaje y la frecuencia de la red el ctrica concuerdan con las descritas en las etiquetas de especificaciones el ctricas del equipo e No introduzca nunca objetos de ning n tipo a trav s de los orificios del equipo Pueden haber voltajes peligrosos Los objetos extra os conductores de la electricidad pueden producir cortocircuitos que provoquen un incendio descargas el ctricas o da os en el equipo S mbolos En este libro aparecen los siguientes s mbolos Precauci n Existe el riesgo de lesiones personales y da os al equipo Siga las instrucciones Precauci n Superficie caliente Evite el contacto Las superficies est n calientes y pueden causar da os personales si se tocan Precauci n Voltaje pel
27. es a clamp on the frame that holds the cable in place 4 Connect the key switch cable connector to the adapter cable connector near the rear of the power sequencer FIGURE 5 1 5 Power on the expansion cabinet See Chapter 3 Chapter 5 Cabinet Subassemblies 5 3 5 3 AC Input Cable Assembly To remove the AC input cable assembly Caution Be sure that the power to the expansion cabinet is completely turned off See Chapter 3 Powering Off the System 1 Disconnect the AC power cord from the power connector on the power sequencer FIGURE 5 3 2 Close the power connector cover 3 Pull the latch up over the cover to secure it FIGURE 5 3 Removing the AC Input Cable 5 4 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 To replace the AC input cable assembly Caution Be sure that the power to the expansion cabinet is completely turned off See Chapter 3 Pull back the power connector cover FIGURE 5 3 Flip the cover latch open to access the connector Connect the power cord to the power connector Pull the latch over the power cord to secure it to the power connector Power on the expansion cabinet See Chapter 3 Chapter 5 Cabinet Subassemblies 5 5 5 4 Power Sequencer To remove the power sequencer 1 Ensure that the power to the expansion cabinet is completely turned off See Section 3 2 Powering Off the Expansion Cabinet
28. es tensions dangereuses Tout objet conducteur introduit de la sorte pourrait produire un court circuit qui entra nerait des flammes des risques d electrocution ou des d g ts mat riels Symboles Vous trouverez ci dessous la signification des diff rents symboles utilis s Attention risques de blessures corporelles et de d g ts mat riels Veuillez suivre les instructions Attention surface temp rature lev e Evitez le contact La temp rature des surfaces est lev e et leur contact peut provoquer des blessures corporelles Attention pr sence de tensions dangereuses Pour viter les risques d lectrocution et de danger pour la sant physique veuillez suivre les instructions MARCHE Votre syst me est sous tension courant alternatif Un des symboles suivants sera peut tre utilis en fonction du type d interrupteur de votre syst me ARRET Votre syst me est hors tension courant alternatif VEILLEUSE L interrupteur Marche Veilleuse est C en position Veilleuse Modification du mat riel Ne pas apporter de modification m canique ou lectrique au mat riel Sun Microsystems n est pas responsable de la conformit r glementaire d un produit Sun qui a t modifi Positionnement d un produit Sun Attention pour assurer le bon fonctionnement de votre produit Sun et pour l emp cher de surchauffer il convient de ne pas obstruer
29. evice in the building installation thus it requires a 30 A circuit breaker Attention Cet quipement d pend du dispositif de protection de l installation lectrique du b timent il n cessite donc un disjoncteur 30 A Achtung Das Ger t arbeitet mit der Schutzvorrichtung in der Geb udeinstallation Daher ist ein 30 A Stromunterbrecher erforderlich seguridad que posea la instalaci n del edificio por lo N Precauci n El equipo utiliza el dispositivo de que necesita un disyuntor de 30 A Safety Agency Compliance Statements vii GOST R Certification Mark Ir viii Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 Contents Preface xi Installing the Expansion Cabinet 1 1 1 1 Features 1 1 1 2 Unpacking the Cabinet 1 2 13 Moving and Placing the Cabinet 1 3 14 Adjusting the Leveling Pads 1 4 15 Installing the Stabilizer Legs 1 5 1 6 Installing the Floor Brackets 1 7 Cabling the Expansion Cabinet 2 1 2 1 Preparing the Expansion Cabinet 2 1 2 2 Connecting the AC Power Cord 2 3 2 3 Connecting the Ground Strap 2 6 2 4 Final Cabling Tasks 2 8 Powering On and Off 3 1 3 1 Powering On the Expansion Cabinet 3 1 3 2 Powering Off the Expansion Cabinet 3 4 Installing and Removing Devices 4 1 4 1 Rackmount Placement 4 1 Contents ix 4 2 4 3 4 4 4 5 4 6 Safety Requirements 4 2 Installing a Device 4 2 Removing a Device 4 5 Side Panel Removal and Repl
30. igroso presente Para reducir el riesgo de descarga y da os para la salud siga las instrucciones Encendido Aplica la alimentaci n de CA al sistema Seg n el tipo de interruptor de encendido que su equipo tenga es posible que se utilice uno de los siguientes s mbolos Apagado Elimina la alimentaci n de CA del sistema En espera El interruptor de Encendido En espera CL se ha colocado en la posici n de En espera Modificaciones en el equipo No realice modificaciones de tipo mec nico o el ctrico en el equipo Sun Microsystems no se hace responsable del cumplimiento de las normativas de seguridad en los equipos Sun modificados Ubicaci n de un producto Sun funcionamiento de su producto Sun y para protegerlo de sobrecalentamien tos no deben obstruirse o taparse las rejillas del equipo Los productos Sun nunca deben situarse cerca de radiadores o de fuentes de calor Precauci n Para asegurar la fiabilidad de Cumplimiento de la normativa SELV vi Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 El estado de la seguridad de las conexiones de entrada salida cumple los requisitos de la normativa SELV Conexi n del cable de alimentaci n el ctrica Precauci n Los productos Sun est n dise ados AN para trabajar en una red el ctrica monof sica con toma de tierra Para reducir el riesgo de descarga el ctrica no conecte los productos Sun a
31. ing the Expansion Cabinet 2 3 3 Check the electrical ratings label on the serial number label attached to the power sequencer Verify that the stated rating matches the AC input voltage to the system TABLE 2 1 and TABLE 2 2 TABLE 2 1 Voltage Requirements for Maximum Operating Voltage and Frequency Ranges AC voltage rating 200 to 240 VAC AC voltage range 180 to 264 VAC Frequency range 47 to 63 Hz TABLE 2 2 Current Requirements at Nominal Line Voltage for a Cabinet in Maximum Configuration Nominal AC input voltage rating single phase 200 to 240 VAC Maximum current requirement 24A at 240 VAC Maximum current per power sequencer outlet 10A 4 Connect the female end of each AC power cord to the power sequencer connectors FIGURE 2 4 Flip the cover latch open to access the connectors 2 4 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 FIGURE 2 4 Connecting the AC Power Cord 5 Pull the latch cover over the power cord to secure it to the power socket Note Route the power cord directly through the opening in the cabinet base 6 Connect the other end of the AC power cord to a grounded outlet The following connector types are provided on the power cord m NEMA L6 30P for 200 240V North American operation m 32A single phase IEC 309 connector for 220 240V international operation ho Caution Risk of electric shock Do NOT turn on AC power to the unit yet Chapter 2
32. n If you will not be using the four floor mounting brackets the four leveling pads mounted on the bottom plate of the rack must be lowered to the floor for the expansion cabinet to meet Underwriters Laboratories physical stability requirements Open the rear door Remove the leveling wrench by unlocking the plastic strap that holds it to the inside of the frame near the top of the expansion cabinet Do not cut the strap Press the plastic tab to unlock the strap around the wrench then slide part of the strap through the lock to loosen the wrench Adjust the four leveling pads on the expansion cabinet frame using the leveling wrench The four pads should press against the floor so that the expansion cabinet does not move or rock in any direction CHIA 2 o Leveling i ot pad FIGURE 1 1 Leveling Pad Proceed to the next section Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 1 5 Installing the Stabilizer Legs Skip to Section 1 6 Installing the Floor Brackets on page 1 7 if you are installing the floor mounting brackets The stabilizer legs help prevent the expansion cabinet from tipping over when devices are taken out of the expansion cabinet The stabilizer legs must be properly installed and set to be effective Caution Always extend the stabilizer legs before you attempt to install new devices or service devices in the expansion
33. net access information see Chapter 4 5 1 5 2 Key Switch To remove the key switch 1 Be sure that the power to the expansion cabinet is completely turned off See Chapter 3 2 Disconnect the key switch cable connector from the cable adapter cable connector near the rear of the power sequencers FIGURE 5 1 The adapter cable remains connected to the power sequencer Key switch cable connector FIGURE 5 1 Key Switch Cable Connection 3 Remove the Phillips screws and cable ties that secure the key switch cable to the chassis frame Each screw secures a clamp on the frame that holds the cable in place 5 2 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 4 Facing the back of the key switch on the inside of the cabinet use a pair of needlenose pliers to slide out and remove the metal clip that secures the key switch to the cabinet FIGURE 5 2 Metal clip Key switch FIGURE 5 2 Removing and Replacing the Key Switch 5 Pull the key switch out of the chassis opening To replace the key switch A Insert the key switch into the panel opening N Facing the back of the key switch on the inside of the cabinet slide the metal clip onto the notch of the key switch body to secure it in place FIGURE 5 2 3 Route the key switch cable to the power sequencer securing it to the chassis frame with cable ties and Phillips screws Each screw secur
34. nhaltung sicherheitsbeh rdlicher Vorschriften Auf dieser Seite werden Sicherheitsrichtlinien beschrieben die bei der Installation von Sun Produkten zu beachten sind Sicherheitsvorkehrungen Treffen Sie zu Ihrem eigenen Schutz die folgenden Sicherheitsvorkehrungen wenn Sie Ihr Ger t installieren e Beachten Sie alle auf den Ger ten angebrachten Warnhinweise und Anweisungen e Vergewissern Sie sich da Spannung und Frequenz Ihrer Stromquelle mit der Spannung und Frequenz bereinstimmen die auf dem Etikett mit den elektrischen Nennwerten des Ger ts angegeben sind Stecken Sie auf keinen Fall irgendwelche Gegenst nde in ffnungen in den Ger ten Leitf hige Gegenst nde k nnten aufgrund der m glicherweise vorliegenden gef hrlichen Spannungen einen Kurzschlu verursachen der einen Brand Stromschlag oder Ger teschaden herbeif hren kann Symbole Die Symbole in diesem Handbuch haben folgende Bedeutung Achtung Gefahr von Verletzung und Ger teschaden Befolgen Sie die Anweisungen Achtung Hohe Temperatur Nicht ber hren da Verletzungsgefahr durch hei e Oberfl che besteht Achtung Gef hrliche Spannungen Anweisungen befolgen um Stromschl ge und Verletzungen zu vermeiden Ein Setzt das System unter Wechselstrom Je nach Netzschaltertyp an Ihrem Ger t kann eines der folgenden Symbole benutzt werden Aus Unterbricht die Wechselstromzufuhr zum Ger t
35. ni recouvrir les ouvertures pr vues dans l appareil Un produit Sun ne doit jamais tre plac proximit d un radiateur ou d une source de chaleur Conformit SELV S curit les raccordements E S sont conformes aux normes SELV Safety Agency Compliance Statements v Connexion du cordon d alimentation Attention les produits Sun sont con us pour fonctionner avec des alimentations monophas es munies d un conducteur neutre mis la terre Pour carter les risques d lectrocution ne pas brancher de produit Sun dans un autre type d alimentation secteur En cas de doute quant au type d alimentation lectrique du local veuillez vous adresser au directeur de l exploitation ou un lectricien qualifi Attention tous les cordons d alimentation n ont pas forc ment la m me puissance nominale en mati re de courant Les rallonges d usage domestique n offrent pas de protection contre les surcharges et ne sont pas pr vues pour les syst mes d ordinateurs Ne pas utiliser de rallonge d usage domestique avec votre produit Sun Attention votre produit Sun a t livr quip d un AN cordon d alimentation trois fils avec prise de terre Pour carter tout risque d lectrocution branchez toujours ce cordon dans une prise mise la terre L avertissement suivant s applique uniquement aux syst mes quip s d un interrupteur VEILLEUSE Attention le commutateur d alim
36. on for devices that can be mounted in Sun system and expansion cabinets is now available through the Web at http docs sun com Click on Storage and Peripherals in the Hardware section and open the Rackmount Placement Matrix If you do not have access to the Web contact your Sun service provider Note Retrieve the placement information for a device before beginning an installation 4 1 4 2 Safety Requirements m Ensure that the voltage and frequency of the power outlet to be used matches the electrical rating labels on the cabinet m Wear an antistatic wrist strap when handling any magnetic storage devices or system boards m Use only properly grounded power outlets Caution Do not make mechanical or electrical modifications to the cabinet Sun Microsystems is not responsible for regulatory compliance of modified cabinets Installing a Device These instructions are meant to be used in conjunction with those that shipped with the device you are installing Read both procedures before beginning the installation Note You may need to remove the side panels from the cabinet If so also perform the steps in Section 4 5 Side Panel Removal and Replacement on page 4 7 Determine where you are going to install the device Refer to the online Rackmount Placement Matrix Open the rear door For cabinets equipped with a front screen door open the front screen door If you want to remo
37. oosen the four 1 4 inch shoulder screws that fasten the panel to the cabinet and remove the panel from the cabinet FIGURE 4 3 7 Le Lim N Ls LT RL ie a 4 SY a FIGURE 4 3 Removing and Replacing the Side Panels Chapter 4 Installing and Removing Devices 4 7 4 5 2 Replacing the Side Panel e Align the panel screw holes to the cabinet screw holes Use an Allen wrench and tighten the four 1 4 inch shoulder screws to fasten the panel to the cabinet FIGURE 4 3 4 6 Troubleshooting the Cabinet Use this checklist as a guide for isolating common installation problems 1 Verify that all terminators are properly installed 2 Verify that all power and data cables are properly installed 3 Verify that the same SCSI address is not being used by two or more drives on the same SCSI bus 4 Verify that the power is turned on to the drives trays and cabinet See the service manual for the peripheral device if you need troubleshooting information for a specific drive or tray 4 8 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 CHAPTER 5 Cabinet Subassemblies This chapter gives the procedures for removal and replacement of all field replaceable units FRUs for the expansion cabinet 5 1 Tools Required m Screwdriver Phillips 2 m Screwdriver slotted 1 4 inch m Needlenose pliers Note For expansion cabi
38. opening is 17 875 inches 454 mm m A vertical panel opening of 36 Rack Unit RU minimum is provided to accommodate various rack mountable subsystems One RU is equal to 1 75 inches 44 45 mm m Overall cabinet height with cosmetic panels is 73 5 inches 187 cm maximum m Cabinet structure and casters are designed to handle a 1300 pounds 589 kg static load Caution Make no mechanical or electrical modifications to this cabinet Sun Microsystems is not responsible for the regulatory compliance if the cabinet is modified A 2 Physical Specifications TABLE A 1 Cabinet Physical Specifications Height Width Depth Weight 73 5 inches 24 inches 36 5 inches 350 pounds 187 cm 61 cm 93 cm 159 kg 1 Weight of an empty cabinet and two power sequencers The power cords are 15 feet 4 6m in length A 3 Clearance and Service Access TABLE A 2 Clearance and Service Access With Service Access Without Service Access Front 48 inches 24 inches 122 cm 61 cm Rear 36 inches 24 inches 92 cm 61 cm Left 36 inches 2 inches 92 cm 51 cm Right 36 inches 0 92 cm 1 Side access may be required for some service procedures Refer to the documentation that came with the devices 2 Sun StorEdge A5000 disk arrays Sun Enterprise 4x00 servers and some other devices require a clearance of at least two inches for airflow Unless otherwise stated in the documentation that shipped with your device no clearance access is required
39. ric shock do not plug Sun products into any other type of power system Contact your facilities manager or a qualified electrician if you are not sure what type of power is supplied to your building ratings Household extension cords do not have overload protection and are not meant for use with computer systems Do not use household extension cords with your Sun product Caution Not all power cords have the same current grounding type three wire power cord To reduce the risk of electric shock always plug the cord into a grounded power outlet Caution Your Sun product is shipped with a The following caution applies only to devices with a Standby power switch as a standby type device only The power cord serves as the primary disconnect device for the system Be sure to plug the power cord into a grounded power outlet that is nearby the system and is readily accessible Do not connect the power cord when the power supply has been removed from the system chassis Caution The power switch of this product functions System Unit Cover You must remove the cover of your Sun computer system unit in order to add cards memory or internal storage devices Be sure to replace the top cover before powering up your computer system Caution Do not operate Sun products without the top cover in place Failure to take this precaution may result in personal injury and system damage Ei
40. utlets must be connected to earth ground Connecting the ground strap between the expansion cabinet and the cabinet nearest to it prevents ground loops between the two cabinets and keeps data errors from occurring Locate the 2 meter grounding strap from the kit that was shipped with your expansion cabinet 2 6 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 2 Screw one end of the ground strap to the power sequencer on the system cabinet or cabinet nearest to the expansion cabinet FIGURE 2 5 a Aa Ground strap FIGURE 2 5 Connecting the Ground Strap to the System Cabinet Power Sequencer 3 Screw the other end of the ground strap the front power sequencer in the expansion cabinet FIGURE 2 6 Chapter 2 Cabling the Expansion Cabinet 2 7 eoooooooooooooooo 0000 Ground strap FIGURE 2 6 Connecting the Ground Strap to the Front Power Sequencer 2 4 Final Cabling Tasks 1 Replace the trim panels Tighten the two screws to secure the front and rear trim panels to the cabinet Note Cables should be routed between the bottom panel and the kick panel if you are routing cables under the floor 2 Close the rear door For pre configured expansion cabinets go to Chapter 3 If you are installing a device in the expansion cabinet go to Chapter 4 2 8 Sun StorEdge Expansion Cabinet Installation and Service Manual July
41. ve the door a Reach inside of the door and push down on the lever attached to the spring of the top hinge pin This will cause the hinge pin to retract into the door b Tilt the door out from the top mounting bracket c Remove the door and set it aside 4 2 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 4 Remove the filler panel that covers where you will install the device FIGURE 4 1 a Use a 2 Phillips screwdriver and loosen the captive screws that fasten the panel to the cabinet b Remove the filler panel and save it for future use Note To maintain proper airflow filler panels must be installed over locations that do not have devices mounted Installed device Trim strip Filler panel FIGURE 4 1 Filler Panel and Trim Strip Installation 5 Ifthe expansion cabinet is not bolted to the ground extend the stabilizer legs The stabilizer legs are located under the front of the cabinet Caution Only extend or retract the stabilizer legs as a pair Be sure that the levelers have been adjusted before attempting to move the stabilizer legs Chapter 4 Installing and Removing Devices 4 3 6 Install the device Refer to the online Rackmount Placement Matrix and the documentation that came with your device Route the SCSI or fiber optic cables from the device to the host system s Refer to the documentation that came with your device Route the power cables from
42. y installed threaded rods you should loosely install the floor brackets to the rods and then to the expansion cabinet 1 Remove the three mounting screws on the bottom right of the expansion cabinet FIGURE 1 5 CARS a a AN N lt e FIGURE 1 5 Removing the Mounting Screws Chapter 1 Installing the Expansion Cabinet 1 7 2 Using a 7 16 inch wrench attach the right floor brackets to the front and back of the expansion cabinet FIGURE 1 6 FIGURE 1 6 Attaching the Floor Brackets 3 Bolt the right floor brackets to the floor The bolts to secure the floor brackets to the floor are not included 4 Repeat Step 1 through Step 3 for the left floor brackets 1 8 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 CHAPTER 2 Cabling the Expansion Cabinet This chapter describes how to connect the power cord to the expansion cabinet power sequencer and how to connect the ground strap and fan fail cable from the expansion cabinet to the server and other cabinets For instructions on how to cable storage device options in the cabinet see the documentation that is shipped with each device 2 1 Preparing the Expansion Cabinet 1 Verify that the key switch located at the bottom front of the expansion cabinet is in the Standby position FIGURE 2 1 Keys for this switch are packed in the kit that was shipped with your cabinet
43. ystem off before moving it Set the Local Remote switch on the expansion cabinet to Local FIGURE 3 2 Turn the AC power sequencer circuit breakers on the expansion cabinet to On FIGURE 3 2 3 2 Sun StorEdge Expansion Cabinet Installation and Service Manual July 2000 6 Turn the key switch at the front of the expansion cabinet to the On position FIGURE 3 3 The expansion cabinet will power on approximately 20 seconds after the key switch is turned on This delay minimizes power surges O Standby 2 b 1 o Sequencer stage 2 O Sequencer stage 1 Main AC power FIGURE 3 3 Front Sequencer Status Lights The three power status indicators on the front panel show the status of the front power sequencer The bottom LED will light as soon as power is applied to the expansion cabinet The LED for sequencer stage 1 will light followed by the LED for sequencer stage 2 Note The bottom LED will not light unless the AC power sequencer circuit breakers for the front power supply are on Note To check the status of the rear power sequencer open the rear door of the expansion cabinet and look at the three green LEDs on the rear power sequencer 7 Turn the power on to the system cabinet See the installation manual you received with your system cabinet for instructions You may have to enter a specific software command when booting the system so that the system will recognize the expansion c
Download Pdf Manuals
Related Search