Home

Recommended Practice for Transit Bus Front and Rear Axle S

image

Contents

1. e The radius at the large diameter end of the rollers is worn to a sharp edge e A visible roller groove in the cup or the cone inner race surfaces The groove can be seen at either the small or large diameter end of both parts e Deep cracks or breaks in the cup the cone inner race or the roller surfaces Copyright 2007 APTA All rights reserved 37 APTA BTS SS RP 004 07 Approved 5 5 07 e Bright wear marks on the outer surface of the roller cage e damage on the rollers and on the surfaces of the cup and the cone inner race that touches the rollers e damage on the cup and the cone inner surfaces that touch the rollers Copyright 2007 APTA All rights reserved 38 APTA BTS SS RP 004 07 Approved 5 5 07 Appendix F Inspection of Brake Drums To achieve maximum drum life and optimum performance proper brake maintenance and brake balance are essential Consult your bus manufacturer s maintenance manual for proper maintenance of the braking mechanism The following procedures are suggested as a means of obtaining maximum service and to determine the need for replacement NOTICE When replacing lining or brake drum on one end of the axle replace the same components on the other end of the axle This will maintain proper braking load on the axle A1 Inspection of Brake Drums When relining brakes the brake drum should be cleaned and inspected To be suitable for further servi
2. E Out of round Balance Balance weight has fallen off or a Specify balanced brake drums l balanced drum was not specified when ordering Rebore brake drum within normal 2 Variation in diameter Heat distortion limits or replace Clean all mounting surfaces check for correct fit and clearance to wheel Improper fit to pilot or improper seating on wheel or hub 3 Concentricity Copyright 2007 APTA All rights reserved 45 APTA BTS SS RP 004 07 Approved 5 5 07 Appendix G Wheel bearing Adjustment Th Recommended Practice RP 618 VMRS 018 WHEEL BEARING ADJUSTMENT PROCEDURES PREFACE The following Recommended Practice is subject to the Disclaimer at the front of TMC s Recommended Maintenance Practices Manual Users are urged to read the Disclaimer before considering adoption of any portion of this Recommended Practice OBJECTIVE The goal of this Recommended Procedure is to achieve a verifiable wheel bearing end play of 0 001 to 0 005 0 025 mm to 0 127 mm SCOPE The following service procedures apply to steer drive and trailer axle assemblies using conven tional double nut or single nut systems Follow these service procedures carefully to prevent pre mature wheel end component failure and increase seal and bearing life ABS anti lock braking systems and traction con trol systems with wheel end sensing require precise bearing adjustment to function properly This Recommende
3. Based Brake Test can be used as part of the inspection process to assess the efficiency of the brake system and its assemblies prior to scheduled repairs A test can measure the operator input application control line air pressure and the brake output delivered brake torque through the wheels An individual brake assembly or axle may lose its effectiveness and not be detected before the brake block is worn to the normal replacement level An ineffective brake can cause side to side or axle to axle imbalances of the total brake system When identified an ineffective brake assembly can be repaired or replaced in addition to the already scheduled repairs 5 2 1 Retarder operation Service brakes are designed to stop a vehicle in a safe and controlled manner however for enhanced drivability and extended brake life some buses are equipped with supplemental braking systems Apparent brake problems could be problems associated with these supplemental brakes Because of the many different applications transmission retarder engine brake driveline retarder and configurations auto apply electronic controlled air controlled consult the OEM manual for proper testing procedures 5 3 Visual inspection Removal of wheels or other components will prevent the inspection of selected brake components Prior to the disassembly of the foundation brake and related wheel brake components thoroughly inspect the foundation brake system which includes the
4. acahors antes adetaecheo putea raatotemnted connect uaiarateaatensantin cate aeauees 15 7 3 Remove the brake adjuster S cam and DUSHINGS ccc ssesssssssseeeecececceeeeeeeeeaaaseeseesecseeeeeeeeeeeeeeeeeaaeaaaeeessees 15 Ceao ann S 6 er Oea Deca mtre mm terere seer m rte Mer DeeeimtemttM tinier onesie we etter Deere caterer ones etr ar mertsNtr Diese nay 17 6 li Spider spinde amd axe CU De cicsas e e E a ouctetuaeinss duvet cialanseheheuesite 17 6 2 CHECKING Wie sSDNCSr Ale INU os asiriee ace aatiatee ental aessnd a tae tn doesn a 17 O50 CaM MIS pec Oesia terran sett ac taeda ea ieiu nda dacteiatsc lala tae a eed atais taal iaala eta wade eae 18 e EE RE oj E PEE eta entre Raat E E EE Rant E A EE PSE E A nates NUR eee 18 S Brakes OC ze a ketal scien Uacandaunaeaiea sceadiceeene 18 oom Gli eres Ml as ere Leno yeaa UG Voy 0 16100 08 Re amnmtetemt ete te rey earn nant ROR pee Ri RN CRC RT Duar Cee RO RN ne Re See 18 Bed WIPO wie saes escag ice acatea lauds ances a a ela ana gamaieaa imcbamacnateleneesae emaraueuaneiaiaanenelen 19 SSUV fa Uo ONE T Leeee nner Mra oe eee ea eee eter e rer nn a rete er tome aren ernie Teter eae arene Tne Ts ener Meerene rt 19 Copyright 2007 APTA All rights reserved 3 APTA BTS SS RP 004 07 Approved 5 5 07 OV ASSeMmUHNS he TOUMG AION DLAKO orie T asia ahebtacetabenaaanes 19 OM Mra CaaS Cer US AN cee a ale ae a a cag aa i eau aaa seis hca al SA 19 OAM TAGS iN US eo ers GN e ho mepeaneee renee E rantt
5. and lock nut arrangement There are also single nut adjusting and locking arrangements If necessary consult the maintenance manual for the correct procedures and tools e Remove the outer wheel bearing cone Note Proper bearing maintenance must be maintained to assure Safe and reliable bearing performance e Keep the bearing cup and cone as a matched set e Replace bearing cups and cones as an assembly e If bearing is dropped the cup and cone must be replaced e Do not spin dry the bearing with compressed air e Use a wheel dolly to remove the wheel drum and hub as an assembly Copyright 2007 APTA All rights reserved 11 APTA BTS SS RP 004 07 Approved 5 5 07 e Remove the front inner wheel seal and wheel bearing Discard the seal Caution Use a seal removal tool that does not put pressure on the bearing or damage the hub seal bore e Wipe all excess grease or oil from spindle Warning Do not use compressed air to remove the brake dust 6 2 Rear wheels hub and drum e Attach shop air to the bus and release the parking brake Ensure the spring brake parking brake is fully released If the spring brake is not releasing or will not stay released the brake will need to be caged or the chamber replaced e Loosen the brake adjuster until there is enough clearance between the shoes and drum to allow the drum to be slid over the shoes and removed Caution Do not use impact wrench on brake a
6. approved seal driver or equivalent gently tap the seal into the seal retainer Listen for the sound changing indicating the seal is seated properly e Lightly coat the lip seal with the same lubricant used on the bearings e Replace the seal retainer gasket install seal retainer and torque fasteners to 20 30 ft lbs 9 9 4 Preset the ABS sensors If equipped Copyright 2007 APTA All rights reserved 29 APTA BTS SS RP 004 07 Approved 5 5 07 For the ABS or speedometer to function properly sensors must be in good condition and adjusted properly Inspect the sensors and wiring for damage Replace as necessary Set pre adjustment by pushing the sensors fully outboard When the wheel hub assembly and bearings are correctly installed the air gap for the sensors will properly position itself automatically 9 9 5 Install hub drum and wheel e Use a wheel dolly to install the wheel drum and hub as an assembly Take care not to damage the wheel seal while installing the assembly e For oil lubricated bearings fill hub with same type lubricant used in the axle sump or hub assembly e Ensure there is a light coat of lubricant on the outer wheel bearing e Install the outer bearing cone onto the axle housing tube e Install the adjustment nut and tighten the adjusting nut to a torque of 200 ft Ibs while rotating the wheel e Back off the adjusting nut one full turn e Tighten the adjusting nut to a final torque of 50 ft Ibs while
7. automatic brake adjuster brake block drums brake chambers mounting fasteners and other system parts Safely raise and support the bus by the axles at an appropriate working height 5 3 1 Confirm need for reline in accordance with agency policies and procedures 5 3 2 Visually inspect the brake block o Check for wear block should not be worn into the wear line if equipped or less than 1 4 inch for 1 4 inch bolt and 3 8 inch for 3 8 inch bolt as measured at the center of the shoe At no time should rivets or bolts touch the drum o Check for movement there should be no movement between the brake block and the shoe o Look for cracks no cracks should have a void greater than 1 16 inch or longer than 1 Copyright 2007 APTA All rights reserved 8 APTA BTS SS RP 004 07 Approved 5 5 07 1 2 inch long o Check for missing segments that expose a fastener o Inspect for signs of block contamination 1 e oil or grease 5 3 3 Make sure all components are appropriate for the application i e proper length brake adjusters proper brake chamber size etc 5 3 4 Dragging tight wheels With all four wheels elevated from the ground rotate each wheel to find dragging or tight brakes 5 3 5 Pushrod travel o Measure pushrod travel at each brake per CVSA standards Pushrod travel should be within 1 4 inch measurement from left to right wheel on the same axle Excessive pushrod travel may be cause to replace the brake adjus
8. examples of abnormal drum wear and the likely cause 8 8 Hub ABS tone ring Inspect the ABS tone ring for damage Be sure that hub is free of grease and debris e Inspect seal bore for scoring or damage e Check that the bearing cups are secure in the bore e Check wheel studs for damage 9 Assembling the foundation brake 9 1 Install S cam bushings Install camshaft bushings with a tool specifically designed for installation to assure proper fit and to avoid distortion to the brake spider Press the bushings until the outer edge 1s flush with the bottom of the seal bore Copyright 2007 APTA All rights reserved 19 APTA BTS SS RP 004 07 Approved 5 5 07 9 2 Install S cam seals Use the appropriate driver to install the camshaft seals Install both seals with seal lips facing the brake adjuster Drive them until they are flush with the bore Lightly lubricate seal lips bushings and camshaft SPIDER 9 3 Install anchor pin bushing Mark lock bolt hole on spider and bushing as shown Align marks to properly locate new bushing Use appropriate tool to drive out old bushing while installing new bushing 9 4 Install S cam Install the cam head washer one only lightly lube the bearing area with a 12 hydroxy lithium stearate chassis Copyright 2007 APTA All rights reserved 20 APTA BTS SS RP 004 07 Approved 5 5 07 grease NLGI grade 1 or 2 and slide the S cam in place Take care not to damage the se
9. good brake maintenance is consistency Both material and procedures must be the same each time a reline is done Consistent procedures and standard component replacement contribute to reliable brake performance Copyright 2007 APTA All rights reserved 29 APTA BTS SS RP 004 07 Approved 5 5 07 APPENDIX B Brake Adjusters Brake adjusters are the link between the brake chamber and the foundation brake The length of adjuster arm affects the force transmitted to the brake by the air chamber The longer the brake adjuster length the higher the force leveraged to the brake This is normally referred to as the AL Area times Length factor The purpose of a brake adjuster is to provide an acceptable shoe to drum clearance in the brake Increased shoe to drum clearance will result in increased air chamber stroke Excessive shoe to drum clearance can result in decreased braking power and increase stopping distances Excessive air chamber stroke may be related to worn components in the foundation brake including the brake adjuster Total air chamber stroke is established by three elements when the brakes are applied e Free stroke the rotation of the cam shaft closing the shoe to drum clearance e Foundation brake parts binding to each other to close tolerances e Foundation brake elasticity aka stretch includes cam shaft wrap wing bracket movement and brake drum stretch Manual Brake Adjusters are common on vehicles manufactured pr
10. hub and bearings are as sembled on the spindle or axle tube torque the inner adjusting nut to 200 Ibf ft 271 Nem while rotating the wheel hub assembly Refer to Table 1 at the end of this Recommended Practice Step 3 Back off the inner adjusting nut one full turn Rotate the wheel Step 4 Re torque the inner adjusting nut to 50 Ibf ft 68 Nem while rotating the wheel hub assem bly Refer to Table 1 at the end of this Recom mended Practice Step 5 Back off the inner adjusting nut Refer to Table 1 at the end of this Recommended Practice for the proper back off amount Step 6 Install the locking washer Issued 3 93 Copyright 2007 APTA All rights reserved 46 If dowel pin and washer or washer tang and nut flat are not aligned remove the washer turn it over and reinstall If required loosen the inner adjusting nut just enough for alignment IMPORTANT Never tighten the inner adjusting nut for alignment at this point of the procedure This may pre load the bearing and cause premature failure Step 7 Install and torque the outer jam nut Refer to Table 1 at the end of this Recommended Practice for proper torque values NOTE This adjustment allows the wheel to rotate freely with 0 001 to 0 005 0 025 mm to 0 0127 mm end play Step 8 Verify end play with a dial indicator Wheel end play is the free movement of the tire and wheel assembly along the spindle axis a Make sure the b
11. rotating the wheel e Back off adjusting nut 4 turn e Install lock washer and or tab type washer e Install the locking nut and torque to 300 400 ft Ibs for dowel style washers or 200 275 for tab style washers e Use a dial indicator to verify a final endplay of 001 005 inch Refer to appendix G for complete text of TCM RP 618 wheel bearing adjustment procedure e Install new gaskets and or seal on hub e Install the axle shafts in the correct side of the housing e Install the dowels washers and nuts Torque to manufactures recommendations using a cross tightening sequence 9 10 Brake adjustment Brake adjuster manufacturers very in their adjustment procedure so it is important to follow Copyright 2007 APTA All rights reserved 26 APTA BTS SS RP 004 07 Approved 5 5 07 their recommended practice However the general rule is to tighten the brake adjuster until the block touches the drum and then back off the brake adjuster 2 to 3 4 turn CAUTION This is not the final brake adjustment and any final testing at this point will be invalid The brake adjusters will continue to automatically adjust to their home position through brake applications during the burnishing process and road test Lower the bus and use a torque wrench to tighten the lug nuts to the appropriate value in the manufacturer recommended sequence Note Recheck wheel lug nut torque after the bus has been in service between 200 and 500 m
12. start the automatic brake adjuster at a 90 position to provide proper input torque to the brake This condition must not be changed The 90 degree rule hence becomes subject to degrees of interpretation as opposed to intended brake design Free Stroke Checking or measuring free stroke is most beneficial when checking the brakes with the vehicle wheels on the ground Determine free stroke movement by measuring the distance of movement of the pushrod when using a pry bar or specially designed tool to manually apply the brakes An average distance of 1 2 inch is considered acceptable If free stroke is less than 3 8 inch check for a dragging brake Use a feeler gauge between the brake drum and brake shoe or elevate and rotate the wheel to determine a Copyright 2007 APTA All rights reserved 31 APTA BTS SS RP 004 07 Approved 5 5 07 dragging brake Power Stroke Power stroke is determined by measuring the total travel distance of the pushrod from any point along the rod using 90 100 psi reservoir brake pressure Power stroke meeting CVSA maximums should be considered an out of service brake and a sign of improper brake operation Adjustment to the automatic brake adjuster without a repair is considered an unsafe practice Identify the cause of the problem and make the necessary repairs to bring the braking system back into proper condition Copyright 2007 APTA All rights reserved 32 APPENDIX C Reline Check List BR
13. 2 APTA BTS SS RP 004 07 Approved 5 5 07 9 8 Install front wheel bearings seals and hub assembly 9 8 1 Grease lubricated bearings e Place the cleaned wheel bearings in the grease packer Pack the bearings with grease until it comes out all sides e Lightly lubricate the spindle with the same grease used to pack the wheel bearing e Fill the hub cavity level to the bearing cups with wheel bearing grease e Lightly coat the bearing races cups with grease e Place the inner wheel bearing in the inner race e Clean all grease from the seal mounting area Note Some seal drivers are designed to have the seal and bearing mounted onto the tool for installation 9 8 2 Oil lubricated bearings Caution Do not grease pack oil lubricated wheel bearings e Lightly coat the inner wheel bearing in oil e Lightly coat the bearing races cups with oil e Place the inner wheel bearing in the inner race e Clean all oil from the seal mounting area Note Some seal drivers are designed to have the seal and bearing mounted onto the tool for installation 9 8 3 Install the wheel seal e Tip the tire wheel assembly against a solid surface e Using the seal manufactures approved seal driver or equivalent gently tap the seal into place with the lip facing the inside of the hub Listen for the sound changing indicating the seal is seated properly e If recommended by seal manufacturer apply a coating of lubricant to the inner seal lip o
14. AKE RELINE CHECK OFF LIST Remove the wheels and drum assembly road side curb side Clean and inspect bearings road side curb side Clean hubs road side curb side Remove brake shoes road side curb side Remove and replace bushings wipers amp seals road side curb side Remove and clean the brake adjuster road side curb side Install and adjust the brake adjuster road side curb side Install shoes springs and rollers road side curb side Pack bearings and install inner wheel seal road side curb side Install wheel and drum assembly road side curb side Adjust wheel bearings end play road side curb side Install gasket seal and hardware road side curb side Burnish and performance test road side curb side QUALITY CONTROL CHECK LIST TASK APTA BTS SS RP 004 07 Approved 5 5 07 SIGN OFF Remove wheels and drums LC Clean and inspect bearings Clean hubs Remove brake shoes Remove and replace wipers Remove brake adjuster and S cam Remove and replace bushings ee Copyright 2007 APTA All rights reserved 33 APTA BTS SS RP 004 07 Approved 5 5 07 TASK SIGN OFF Retrieve a set of turned brake drums dl Retrieve reline kit from inventory 4 TASK SIGN OFF Install brake adjuster and S cam Ld Install shoes springs and rollers Pack bearings and install inner wheel seal Install wheel and drum assembly a Adjust wheel bearing end play Install gaskets seals axles and hardware Burnish an
15. APTA BTS SS RP 004 07 Approved 5 5 07 Recommended Practice for Transit Bus Front and Rear Axle S Cam Brake Reline Approved February 1 2007 APTA Bus Brake Working Group Approved May 5 2007 APTA Bus Standards Committee Abstract This recommended practice provides guidelines for performing a complete brake reline on the front and rear axle of a bus with S cam brakes The practice includes the disassembly cleaning inspection and assembly This recommended practice is to be used in conjunction with the manufacturer s service manual lt is recommended that all components be replaced equally on both wheel ends of the axle Failure to do so may affect braking performance Keywords Anchor pins brake shoes S cam bushings brake adjuster wheel bearings spider return spring wheel seals brake shoe rollers brake rebuild brake reline brake maintenance Copyright 2007 by The American Public Transportation Association 1666 K Street NW Washington DC 20006 1215 USA No part of this publication may be reproduced in any form in an electronic retrieval system or otherwise without the prior written permission of The American Public Transportation Association APTA BTS SS RP 004 07 Approved 5 5 07 Introduction This Recommended Practice for Transit Bus Front Rear Axle Brake Reline reflects the consensus of the APTA Bus Standards Program members on the items methods and procedures that have provided the best performance record bas
16. Cause Abrasive foreign material or Rebore brake drum within normal limits poor quality brake lining or replace the drum and lining 1 Fine Grooving 2 Grooves along Abrasive foreign material Dust shield may cause or cure this edges of lining collecting at edges of lining problem 3 Grooves Loose rivets bolts or foreign coincide with rivet material collecting in rivet or bolt holes Rebore brake drum within normal limits alee or replace Use rivet hole plugs C1 Grooving Fine Grooves C2 Grooving Grooves along edges of lining Copyright 2007 APTA All rights reserved 42 APTA BTS SS RP 004 07 Approved 5 5 07 D Miscellaneous Drum Wear Probable Promem Eee somon 1 Blue or discolored braking surface Rebore brake drum Excessive heat within normal limits or replace Check brake balance weak or 2 Scale on broken return Excessive heat outside springs brake adjustment and lining Loose rivets bolts or foreign material collecting in rivet or bolt holes Rebore brake drum within normal limits or replace Use rivet hole plugs 3 Grooves coincide with rivet holes Check maximum diameter and rebore within limit or replace D2 Scale On Outside Abrasive foreign material or poor quality lining 4 Excessive wear Copyright 2007 APTA All rights reserved 43 D Miscellaneous Drum Wear Probable Posem ae ction 5 Heat spotted or hard spots in brake surfac
17. FINE TUNING THE ADJUSTMENT lf after performing the readjustment procedures end play is 0 004 0 005 0 102 mm 0 127 mm range repeat the appropriate procedures remov ing the washer from the spindle tighten or loosen With indicator mounted at bottom push pull at sides of drum b without tire assembly Fig 1 Dial Indicator Set Up 2003 TMC ATA RP 618 2 Copyright 2007 APTA All rights reserved 47 the inner adjusting nut the equivalent of 1 2 of an alignment hole of the washer or reversing the alignmentwasher and reinstalling it onto the spindle Reassemble and re torque the outer jam nut Refer to Table 1 for torque values Verify end play with a dial indicator NOTE Bendable type washer lock only Secure nuts by bending one wheel nut washer tang over SINGLE NUT ADJUSTMENT Cott aa D Washer TANG TYPE LOCK ADJUSTING NUT APTA BTS SS RP 004 07 Approved 5 5 07 the inner and outer nut Bend the tangs over the closest flap perpendicular to the tang See Fig 2 CAUTION Before operating the unit the wheel hub cavities and bearings must be lubricated to prevent failure For final wheel end assembly refer to TMC RP 622 SPINDLE WASHER TYPE ADJUSTING NUT Bend tangs perpandicular to closest Wheel bearing adjusting nut der inner Wheel bearing adjusting nut inner Outer nut D Type Tang Type Dowel Type Fig 2 Adjusting Nut Identificatio
18. al chassis grease It is important to use the proper grade of grease per manufacturer s recommendation Note Not all automatic brake adjusters require the same maintenance procedures Be sure to follow the specifications of the manufacturer 6 Removal of the wheels hubs and drums 6 1 Front wheels hubs and drums Back off the brake adjuster until there is enough clearance between the shoes and drum to allow the drum to be removed Copyright 2007 APTA All rights reserved 10 Caution Do not use impact wrench on the brake adjuster APTA BTS SS RP 004 07 Approved 5 5 07 Note The procedure used to back off the brake adjuster will depend on the type of brake adjuster used Check with the manufacturer for a detailed procedure e Check the hubcap for leaks or damage e If the bus uses oil lubricated bearings drain the oil into an appropriate container and dispose of the oil in accordance with local regulations or company policy e Remove the cap screws from the hubcap e Remove the hubcap and discard if damaged Remove and discard the gasket e Bend the tab of the lock washer away from the flat on the lock nut e Remove the lock nut lock washer pierced locking ring and adjusting nut Caution Always use the proper size socket when tightening or loosening the lock nuts Do not use a hammer and chisel to loosen and remove the nut Note The procedure above is typical of an adjusting nut lock mechanism
19. als while installing the camshaft Check S cam for proper fit clearance and 360 rotation 9 5 Install brake adjusters Install the correct OEM spacer washer between the spider and the brake adjuster lubricate the cam shaft spines with a temperature resistant anti seize Slide the brake adjuster onto the S cam Install the shim pack removed earlier and snap ring or retaining washer and bolt Check for 030 to 060 lateral movement of the brake adjuster It may be necessary to reposition the shims or select different thicknesses of shims to achieve this result Ensure there is no interference between pushrod and the brake chamber and the brake adjuster aligns with the clevis 9 6 Install brake shoes When using combination lining install primary and secondary shoe assemblies in proper location per manufacturer s recommendations e Lubricate the anchor pins with a NLGI Grade 1 or equivalent grease The grease must handle the high temperatures without flowing and remain soft under normal service Consult the manufacturer s manual for the correct lubricant e Slide the anchor pins through the brake shoes spider and any necessary spacers or washers taking care that the grease fittings on the anchor pins are at the backside of the spider and easily accessible for routine maintenance Install the locking hardware Check that the shoes rotate freely on the anchor pin e Lubricate anchor pins through grease fitting until c
20. and grease Measure push rod travel at each wheel Refer to the CVSA Brake Adjustment Limit listed below Clamp Type Brake Chamber Brake Adjustment Limit Brake Adjustment Limit 1 3 8 1 3 4 1 3 4 2 1 4 1 3 4 Long Stroke Type Brake Chamber Brake Adjustment Limit Brake Adjustment Limit i 2 1 2 oo Not yet added to CVSA criteria Copyright 2007 APTA All rights reserved 28 APTA BTS SS RP 004 07 Approved 5 5 07 APPENDIX A Background The function of brakes is to stop the vehicle control speed and hold it stationary The action of applying the brakes sets up a force effective at the road surface which acts in the opposite direction to the motion of the vehicle causing it to slow down or decelerate The ability of the brakes to perform their function is known as braking efficiency and can be measured There are legal regulations that require all vehicles to have an efficient braking system FMVSS 121 requires vehicle manufacturers to have a braking system capable of achieving a specific minimum deceleration If correctly maintained and operated within its designed load limits the braking system will achieve the minimum braking efficiency required Brakes are designed to a specific geometry If any part of the foundation brake assembly is bent or distorted brake performance may become erratic and unpredictable Always replace bent or distorted parts in order to make sure the brakes function correctly The key to
21. anette ate tetanic eke alse 5 LAE 016 cc meme ee emes E a cen tT ant Tene Nene yImes HraTer are ateG ET nae pr neta ear vet foate mrt serers nar here ent aer Greener oat 5 gS STS TS INC SS ten n Sets ete as ats des ua asst alloy ates SUIS wanna cae areas Ade etal 5 Detimitions Abbrev anons anid ACrOM VIS ieac ra 5 a A EENE E R AE E EARE E EE EAE A SOE A SI E EA EE AEE E A eee 5 9 2 These teins are Miler Chan eab e a E A steduateneat 5 Hazardous maternal Warn E a a 6 ES a AE o EA E T E T E A E E E T EA E mer rere oT 7 5 Vehicle brake and imamtenance NiStOry anes tencose at etel ciara eens eae Aaa 7 JL OvetalliPerormance Based Brake TeS brerr e A E 7 IIN Paal CC NON eiaa E de cs arate aeedanainals da cteand eect 8 5 4 Automatic brake adjuster maintenance inspection and testing cccccccccccceccceeeesseeeeeseeseeeeeeeeeeeeeeeeeeaaaaenees 10 Removal or tne Wheels MUDSsand Grums ssacnc eetes Seidel dade a he dowdalenie iach etal ae lad chun die 10 Pa WS hor a Gam cel UU Lo rs 1 6 Mera 110 0c hc eae ee emer CO a Eo on ATE Steet On we ame ve Ucn ern 10 6 2 Rear Wheels nulb andr Criss scnctala sities aie sita case cia sssens asses cise ceaveuia aaa seca weal aa a oenilanaaaneeeunees 12 Founda on Dhake CISaSSeIIOl Vay asin horetaiate A teeth hcorest eat horse tee tases keane 15 7A AMSDeCU DEAKe SHOES DELOLE TEMOV al it eacccus tases cieicsuia adres cous E aleveaee mea miate ener ena 15 TA ISASSeinble he LOUNGALIOM Drake aditensicce sistas
22. ause a vehicle to pull or drift Copyright 2007 APTA All rights reserved 9 APTA BTS SS RP 004 07 Approved 5 5 07 during braking Carefully inspect the torque rod bushings drag links tie rod ends king pins and shock absorbers as part of every pre reline inspection In many cases it s more efficient to replace repair these parts during the reline because the wheel assemblies are removed 5 4 Automatic brake adjuster maintenance inspection and testing Clean and inspect per manufacturer s recommendation or replace Caution Do not submerge brake adjusters in solvent water or hot tank All Automatic Brake Adjusters require inspection at periodic intervals This should be done at your normal preventative maintenance inspection At these times you should do the following Measure and record the brake chamber pushrod travel with reservoir pressure between 90 and 100 psi and brakes fully applied Grease each brake adjuster Inspect each brake adjuster for integrity and connection points at the clevis and brackets if used Check for a difference in the stroke length between the left and right side of the axle There should be no more than 1 2 difference If the stroke exceeds the CVSA or DOT maximum allowances do not manually adjust the automatic brake adjuster Follow the manufacturer s procedure to determine the cause of the excessive stroke Note Some brake adjusters use special grease while others use norm
23. ce the brake drum should pass the following checks A The braking surface should be free of scoring excessive heat checks and free of cracks B The braking surface diameter should be within the maximum diameter cast or stamped on the drum or minimum thickness cast or stamped on the rotor C The mounting holes and pilot must be round and true D The mounting surface must be clean and flat CAUTION If any of the above conditions are not met the brake drum should be replaced NOTICE Brake drums should be replaced in pairs to achieve the same braking power on the axle A2 Machining the Brake Surface It may be desirable to turn or resurface the braking surface to remove small heat checks or other surface defects The following should be noted when turning Copyright 2007 APTA All rights reserved 39 APTA BTS SS RP 004 07 Approved 5 5 07 When resurfacing a drum allow a margin under the maximum diameter for additional wear depending on agency experiences Example For a wear allowance of 0 040 the drum may be machined a total of 0 290 over the brake surface diameter of a new brake drum with a nominal diameter of 14 500 Maximum Diameter 14 830 Wear Margin 0 040 Machining Allowance 0 290 New Drum Diameter 14 500 WARNING DO NOT WEAR A BRAKE DRUM BEYOND THE MAXIMUM DIAMETER STAMPED OR CAST ON THE BRAKE DRUM The maximum diameter or discard diameter is the maximum diameter to which the brake drum may be wo
24. d Practice details proper service procedures for D type bendable type and dowel type spindle nut washers NOTE For single nut self locking systems consult manufacturers instructions If you have a system that differs from what is indicated in this procedure consult the vehicle manufacturer s recommended procedure WARNING Never work under a unit supported by only a jack Always support the vehicle with stands Block the wheels and make sure the unit will not roll before releasing brakes CAUTION If your axle is equipped with spoke wheels and the rim clamps have been disas sembled to remove the tire and rim assembly the tire and rim assembly must be reinstalled and the rim clamps properly torqued BEFORE 2003 TMC ATA RP 618 1 adjusting the wheel bearings Failure to do this may result in improper wheel bearing adjust ment REFERENCES TMC RP 622 Wheel Seal and Bearing Removal Installation and Maintenance PROCEDURES Step 1 Lubricate the bearing with clean axle lubri cant of the same type used in the axle sump or hub assembly IMPORTANT a In oil bath systems that rely on differential fill to provide lubricant to the wheel seals do not pack bearings with grease before installation Grease will temporarily re strict or prevent the proper circulation of axle lubricant and may contribute to wheel seal failure b Never use an impact wrench to adjust wheel bearings Step 2 After the wheel
25. d performance test Copyright 2007 APTA All rights reserved 34 APTA BTS SS RP 004 07 Approved 5 5 07 APPENDIX D Inspection of Brake Shoes For additional information and examples refer to TMC RP 607B The following pictures are examples of commonly found brake wear problems This is an example of excessive heat that could have been caused by m Overworking of the brakes m Weak return spring if lower shoe only Brakes adjusted too tight m Wrong friction material for the application This is an example of wear caused by a bent or misaligned spider This is an example of a bell mouth drum Copyright 2007 APTA All rights reserved 35 APTA BTS SS RP 004 07 Approved 5 5 07 This is an example of an oversize drum This is an example of cracked lining that could be caused by 7 Bent shoe table Improper installation of brake block m Improper brake block for application This is an example of a missing or broken segment Copyright 2007 APTA All rights reserved 36 APTA BTS SS RP 004 07 Approved 5 5 07 APPENDIX E Inspect Wheel Bearings For additional information and examples refer to TMC RP 607B Remove all lubricant from the bearings Inspect the cup the cone the rollers and cage of all bearings If any of the following conditions exist the bearing MUST be replaced e The center of the large diameter end of the rollers is worn level or below the outer surface
26. djuster Note The procedure used to back off the brake adjuster will depend on the type of brake adjuster used Check with the manufacturer for a detailed procedure e Loosen the axle nuts e There are multiple methods for removing the axle o Jack screws o Axle shaft puller Opo88 amp 9 o Cover the raised boss on the center of the axle flange and strike with hammer e After breaking the axle loose remove the nuts washers and alignment dowels e Remove the axle shaft from the housing NOTE The street side and curbside shafts may differ Make sure they get reinstalled on the same side as they were removed e Remove and discard any seals and gaskets Copyright 2007 APTA All rights reserved 12 APTA BTS SS RP 004 07 Approved 5 5 07 e Remove the lock nut lock washer and pierced locking ring e Remove the outer bearing cone from the wheel hub Caution Always use the proper size socket when tightening or loosening the lock nuts Do not use a hammer and chisel to loosen and remove the nut Note The procedure described above is typical of an adjusting nut locking mechanism and lock nut arrangement There are also single nut adjusting and locking arrangements If necessary consult the maintenance manual for the correct procedures and tools Proper bearing maintenance must be maintained to assure safe and reliable bearing performance Keep the bearing cup and cone as a matched set o R
27. e Greased Stained Drums 7 Faded or diminished brake power 8 Noise chatter or pulsating during brake application Highly localized heating and cooling cycles Leaking oil seal improper lubrication of brake components High temperature in brake system improperly adjusted brakes or inferior brake lining Heat spotted drums greased stained drums loose brake drum or brake components Copyright 2007 APTA All rights reserved Grind hard spot and re bore brake drum within normal limits Repair source of oil or grease leak clean the brake drum and replace linings Check brake drum brake lining condition brake adjustment and brake balance Avoid operation conditions or loads which create excessive brake temperature The bake drums should be removed and checked for one or more of these conditions and the appropriate action taken to resolve the condition APTA BTS SS RP 004 07 Approved 5 5 07 D5 Heat spotted or Hard Spots D6 Greased Stained Drums 44 APTA BTS SS RP 004 07 Approved 5 5 07 D Miscellaneous Drum Wear Probable Cause Solution 9 Polished Brake Surface a Non asbestos lining Normal condition Insufficient braking input force i e overly Remove glaze with emery cloth aggressive retarder or lining we rebore drum material ee normal D9 Polished Glazed Braking improper brake d Stace balance b Glazed surface
28. e The cylinders have vacuums with HEPA filters and arm sleeves If such equipment is not available carefully clean parts and assemblies in the open air e During disassembly carefully place all parts on the floor or in a suitable cleaning station to avoid getting dust into the air After vacuum cleaning any remaining dust should be removed using a rag soaked in water and then wrung until nearly dry e If it is necessary to grind or machine brake linings additional precautions should be taken because contact with fiber dust is higher during these operations In addition to wearing an approved respirator such work should be done in an area with exhaust ventilation Copyright 2007 APTA All rights reserved 6 APTA BTS SS RP 004 07 Approved 5 5 07 e NEVER use compressed air or dry sweeping to clean the work area Use an industrial vacuum with HEPA filters and rags soaked in water and wrung until nearly dry Used rags should be disposed of with care to avoid getting dust into the air Use an approved respirator when emptying vacuum cleaners and handling used rags e Workers should wash their hands before eating drinking or smoking Work clothes Should not be worn home but should be vacuumed after use and then laundered separately without shaking to prevent dust from getting into the air 5 Initial inspection In cases where components such as brake adjusters brake chambers and camshafts are not scheduled for replacemen
29. ed on the experiences of those present and participating in meetings of the Program Task Forces and Working Groups Recommended practices are voluntary industry developed and consensus based practices that assist equipment suppliers vehicle and component manufacturers and maintenance personnel in the construction assembly operation and maintenance of transit bus vehicles Recommended practices may include test methodologies and informational documents Recommended practices are non exclusive and voluntary they are intended to neither endorse nor discourage the use of any product or procedure All areas and items included therein are subject to OEM s and manufacturers supplemental or superseding recommendations APTA recognizes that for certain applications the practices as implemented by operating agencies may be either more or less restrictive than those given in this document This document is recommended for e Individuals or organizations that inspect and maintain transit buses e Individuals or organizations that contract with others for the inspection and maintenance of transit buses e Individuals or organizations that influence how transit buses are inspected and maintained Copyright 2007 APTA All rights reserved 2 APTA BTS SS RP 004 07 Approved 5 5 07 Table of Contents LOVON O asceuertietshcessne mani A aaaueesa aes oneuatncmietanck 5 Msg SO OG eie ata cea helena den ian hac tra ats natant cle at sei pa nantes
30. emove the brake adjuster e Remove and discard cotter pin Remove clevis pin and inspect for wear Replace as necessary e Inspect the yoke and brake adjuster bushing for wear Replace parts as necessary e Remove the snap ring or retaining bolt and washer from the end of the s cam e If equipped disconnect the brake adjuster adjustment bracket e Remove the brake adjuster and the spacing washers e Inspect all parts and replace as necessary 7 3 2 Remove S cam and bushings Once the brake adjuster and brake shoes have been removed the S cam can be slid out towards the outside of the bus Remove and discard camshaft bushings at every reline Camshaft bushings keep the cam and brake shoe assemblies centered in the brake drum As the bushings wear they allow the camshaft to fall off center creating unequal drum clearance between the top and bottom shoes This can affect pushrod travel braking torque and braking performance To remove the bushings use a tool specifically designed for bushing removal or a soft driver such as a brass or aluminum punch Drive the inner S cam bushing out towards the center of the bus Remove the outer bushing using the procedure above driving the bushing from the center of the bus towards the outside Copyright 2007 APTA All rights reserved 16 APTA BTS SS RP 004 07 Approved 5 5 07 Note There is a ridge in the center of the spider that prevents the bushings from being rem
31. eplace bearing cups and cones as an assembly o If bearing is dropped the cup and cone must be replaced o Do not spin dry the bearing with compressed air e Place a wheel dolly under the dual rear wheel Use the wheel dolly to carry the weight of the rear wheels Remove the wheels drum and hub as an assembly e If the inside wheel seal uses an oil seal wiper sleeve remove it by hitting the oil seal wiper with Copyright 2007 APTA All rights reserved 13 APTA BTS SS RP 004 07 Approved 5 5 07 a hammer to loosen it Use a punch or chisel to drive the oil wiper sleeve off the housing then discard e If the bus is equipped with an outside wheel seal using an oil seal wiper sleeve use a punch to remove the oil seal wiper and cork assembly then discard e To replace inner wheel seal remove the screws attaching the inner seal retainer to the hub e Remove the inner seal retainer assembly and gasket along with the inner wheel bearing cone e Discard the gasket e Using a soft punch drive the seal from the retainer taking care not to damage the sealing surface of the retainer e Thoroughly clean all grease from the wheel and hub Copyright 2007 APTA All rights reserved 14 APTA BTS SS RP 004 07 Approved 5 5 07 7 Foundation brake disassembly 7 1 Inspect brake shoes before removal The way the brake block has worn can help determine the condition of the foundation brake Look for unusual pattern
32. he center of the clevis pin when the air chamber is fully caged This measurement is determined by the brake manufacture and or the bus OE to set up the correct angle of the brake adjuster between the air chamber pushrod and cam shaft Brake adjuster performance is determined by the angle of the automatic brake adjuster set by the brake designer Changes to shorten or extend the pushrod length of a stroke sensing adjuster may cause the brake adjuster to over or under adjust Some types of automatic brake adjusters have an additional connecting rod from the yoke to the adjuster The correct pushrod length is designed to activate the point of adjustment on the applied stroke Maintaining the correct pushrod length is important for all automatic brake adjusters for maximum braking performance The 90 degree rule This rule was commonly used when manual brake adjusters where the norm The brake adjuster should not exceed a 90 degree angle in the brake applied position By properly setting the pushrod length and adjusting the brake the angle would not exceed the 90 degree position The theory is to maximize braking force This rule was never adopted into written law but was referred to in numerous documents to visually determine the re adjustment limit of a manual brake adjuster Today s design criteria allow the adjuster to operate from 85 degrees to 105 degrees to provide proper input torque to the brake In some cases designers
33. his document establishes a recommended practice for transit bus Front Rear axle brake reline Individual operating agencies should modify these guidelines to accommodate their specific equipment and mode of operation 1 1 Scope This recommended practice provides guidelines for disassembly preparation inspection and reassembly of the typical heavy duty transit bus s cam brakes The components may be different than pictured and some procedures will vary 1 2 Purpose The purpose of this document is to provide a uniform standard for heavy duty transit bus brake reline 2 References This recommended practice is to be used in conjunction with the original equipment manufacturer OEM and brake manufacturer service manuals 3 Definitions abbreviations and acronyms 3 1 Definitions Brake Shoe Assembly consists of the brake shoe and the brake block MSDS Material Safety Data Sheet OSHA Occupational Safety and Health Administration NIOSH National Institute for Occupational Safety and Health MSHA Mine Safety and Health Administration HEPA High Efficiency Particulate Air NLGI National Lubricating Grease Institute 3 2 These terms are interchangeable Brake Block friction material brake lining Brake adjuster slack adjuster S cam camshaft Bearing cups bearing races Copyright 2007 APTA All rights reserved 5 APTA BTS SS RP 004 07 Approved 5 5 07 Brake chamber air chamber Machini
34. iles 10 Burnishing testing and final inspection 10 1 Burnishing Burnishing procedures may be modified for each agency s requirements but should be similar to the following steps a Turn the retarder off if possible until the burnishing procedure is complete b Use the service brake to slow the vehicle from 20 to 5 mph at approximately 0 3 g deceleration or a moderate brake application snubbing Repeat this snubbing process a minimum of 10 times at regular intervals of approximately 500 ft or 0 1 mile without stopping the vehicle CAUTION Do not permit wheel lock up c After completing the snubbing process in b make one complete stop from 20 to 0 MPH d Immediately after burnishing compare brake temperatures measured in the exact same location at each wheel example on the drum or wheel stud Any significant temperature differential approximately 50 F side to side 100 F front to rear indicates a braking problem Inspect the vehicle for brake defects and repair as necessary After repairs have been made repeat burnishing process 10 2 Performance test Test the vehicle using APTA Recommended Practice for In Service Brake Testing BT RP 001 05 Verify that the vehicle meets your agency or government regulations Copyright 2007 APTA All rights reserved 2i APTA BTS SS RP 004 07 Approved 5 5 07 10 3 Final inspection Visually check brakes for e Loose or broken components e Leaks oil air
35. ior to October 1994 with S cam drum brakes These adjusters require periodic manual adjustment to maintain proper shoe to drum clearance in the brake Manual brake adjusters contain a locking ring and adjustment nut to adjust the brake The need to perform brake adjustments will vary widely depending on the severity of service Automatic brake adjusters are required on vehicles manufactured after October 1994 with S cam drum brakes Automatic brake adjusters perform the same function as manual brake adjusters however they re able to do it without the need for periodic manual adjustment Some of the benefits of the automatic brake adjuster are Automatic brake adjustment Reduced down time and maintenance cost Improved brake balance and performance Reduced air chamber travel and less air consumption Higher margin of braking safety Automatic brake adjusters do require attention during routine maintenance inspections but are not intended to be adjusted manually to improve braking performance Brake Adjuster Angle and Pushrod Length Brake adjuster angles are determined by the length of the pushrod with yoke attached The Copyright 2007 APTA All rights reserved 30 APTA BTS SS RP 004 07 Approved 5 5 07 angle of the adjuster as determined by brake engineers when the air chamber is fully caged released sets the operation of the adjuster to perform properly Pushrod length is measured from the face of the air chamber to t
36. l e Back off the inner adjusting nut turn e Install lock washer and or tab type washer e Install the locking nut and torque to 300 400 ft Ibs e Use a dial indicator to verify a final endplay of 001 005 inch Refer to appendix G for complete text of TCM RP 618 wheel bearing adjustment procedure e Install a new gasket hubcap and bolts Tighten the hubcap bolts 20 30 ft Ibs Note For oil lubricated bearings add appropriate oil per manufacturer s recommendations Copyright 2007 APTA All rights reserved 24 APTA BTS SS RP 004 07 Approved 5 5 07 9 9 Install rear wheel bearings seals and hub assembly If equipped use an appropriate driver to install inner seal wiper 9 9 1 Grease lubricated bearings e For grease lubricated bearings place the cleaned wheel bearings in the grease packer Pack the bearings with grease until 1t comes out all sides e Lightly lubricate the axle tube with the same grease used to pack the wheel bearing e Fill the hub cavity level to the bearing cups with wheel bearing grease e Lightly coat the bearing races cups with grease e Place the inner wheel bearing in the inner race 9 9 2 Oil lubricated bearings Caution Do not grease pack oil lubricated wheel bearings e Lightly coat the inner wheel bearing in oil e Lightly coat the bearing races cups with oil e Place the inner wheel bearing in the inner race 9 9 3 Install the wheel seal e Using the seal manufactures
37. lean grease is visible between the shoe and washer Wipe away any excessive grease Note Do not get grease on the brake shoe lining e Install brake shoe return spring s ensuring they do not interfere with adjacent components s cam shoes hub etc Copyright 2007 APTA All rights reserved 21 APTA BTS SS RP 004 07 Approved 5 5 07 CAUTION Consult manufacturer s manual for specific brake type or configurations e If the brake rollers have not been installed lubricate the roller pockets of the brake shoe with a NLGI grade 1 or equivalent grease the grease must handle the high temperatures without flowing and remain soft under normal service e Spread the brake shoes apart and install the brake shoe rollers Let the shoes snap against the S cam to make sure the rollers are seated equally and fully in the brake shoes and the S cam pockets Note Ensure there 1s no lubricant on the contact surfaces between the rollers and S cam head 9 7 Install brake adjuster hardware e Rotate the brake adjuster arm into the yoke by turning adjusting hex nut clockwise Lubricate and install clevis pin and new cotter pin e If equipped install and adjust brake adjuster control arm bracket or other connections as necessary per manufacturer s recommendations e Lubricate all remaining grease fittings Ensure proper installation of all components before installing tire hub and drum Copyright 2007 APTA All rights reserved 2
38. n and Installation 2003 TMC ATA RP 618 3 Copyright 2007 APTA All rights reserved 48 APTA BTS SS RP 004 07 Approved 5 5 07 TABLE 1 WHEEL BEARING ADJUSTMENT PROCEDURE STEP 1 Lubricate the wheel bearing with clean axle lubricant of the same type used in the axle sump or hub assembly Note Never use an impact wrench when tightening or loosening lug nuts or bolts during the procedure INITIAL INITIAL BACK OFF JAM NUT TORQUE ACCEPTABLE ADJUSTING BACK OFF ADJUSTING THREADS FINAL NUT TORQUE END PLAY NUT PERINCH BACKOFF SIZE SPECIFICATIONS TORQUE TORQUE STEP3 STEP4 STEP5 STEP6 STEP 7 STEP 8 1 6 Turn Install Cotter Pin to Lock Axie Nut in Position Steor 1 4 Turn Front Non Drive Less Than 200 300 Ibeft 0 001 0 005 1 2Turn 2 5 8 271 407 Nem 025 127 mm 200 Ibeft 50 Ibeft 66 7 mm 271 Nem 68 Nem While While Rotating Rotating 300 400 Ibeft As Measured Wheel Wheels 407 542 Nem Per Procedure 1 4 Turn With Dial Tang Type 200 275 Ibeft Indicator Washer 271 373 Nem 2 5 8 300 400 Ibeft Trailer 1 4 Turn 66 7 mm 407 542 Nem and over If dowel pin and washer or washer tang and nut flat are not aligned remove the washer turn it over and reinstall If required loosen the inner adjusting nut just enough for alignment Bendable type washer lock only Secure nuts by bending one wheel nut washer tang over the inner and outer nut Bend the tangs over the clo
39. ng turning reboring grinding sanding and cutting Pushrod travel air chamber power stroke 4 Hazardous material warning Most brake linings no longer contain asbestos fibers However if working with any component that does contain asbestos take all the necessary precautions prescribed by OSHA and follow all federal provincial state and local safety requirements The health impact of non asbestos fibers e g brake block with glass mineral wool ceramic aramid carbon etc is not specifically covered under current OSHA regulations Although medical experts do not agree about the possible long term risks of working with and breathing non asbestos fibers some experts believe that long term exposure could cause pneumoconiosis fibrosis and cancer Therefore it 1s recommended that workers avoid dust when working on brakes that contain non asbestos materials Brake block may also contain crystalline silica lead antimony phenol and other possibly hazardous materials Refer to the material s MSDS for all necessary precautions Follow the general safety procedures listed below when working with braking components e Whenever possible work on brakes in a separate area away from other operations e Always wear a respirator approved by NIOSH or MSHA during all brake service procedures e NEVER use compressed air or dry brushing to clean brake parts or assemblies OSHA recommends that you use cylinders that enclose the brak
40. oved or installed in any manner other than what is described in this document o 8 Cleaning and inspection 8 1 Spider spindle and axle tube Thoroughly clean the axle tube spindle and spider assembly Use a cleaner that complies with local safety and environmental regulations and agency policy Warning Do not use compressed air to remove the dirt and dust from the brake assembly After the spider has been cleaned check for e Cracks e Worn anchor pin holes e Loose fasteners e Bent spider brake shoe anchor pins must hold the shoe and lining assemblies parallel to the brake drum surface After the spindle axle tube has been cleaned check for e Cracks e Damaged threads e Damaged seal surface e Damaged bearing seats 8 2 Checking the spider alignment Proper spider alignment is determined by making sure the axle tube is parallel to the anchor pin holes To use this tool tighten the clamp section around the axle tube insert the pin into the anchor pin hole and tighten the knurled nut that holds the Copyright 2007 APTA All rights reserved 17 APTA BTS SS RP 004 07 Approved 5 5 07 pin If the spider is not bent the pin will slide all the way through the anchor pinhole If the spider is bent the pin will not slide into the anchor pinhole or will only slide in part way If alignment is not correct replace spider and recheck 8 3 S Cam inspection Check the camshaft splines head and journals fo
41. r cracks wear and corrosion Check the journal areas of the camshaft for wear using a go no go gauge When checking the journal area check it in several locations because the journal will not wear evenly Replace worn or damaged camshafts Note Do not dress or regrind camshaft 8 4 Springs and rollers Replace brake shoe return springs and rollers at each reline 8 5 Brake shoes Refer to APTA BT RP 005 07 Brake Shoe Rebuild for disassembly cleaning inspecting and rebuilding 8 6 Wheel bearing inspection Copyright 2007 APTA All rights reserved 18 APTA BTS SS RP 004 07 Approved 5 5 07 Roller bearings should be cleaned according to manufacturer s recommendation and inspected It is important to keep bearing cups and cones matched Remove all the old lubricant using a cleaner that complies with local safety and environmental regulations and agency policy Do not spin dry the bearings with compressed air Inspect the cup the cone the rollers and cage of all bearings See Appendix E for examples of bearing wear and damage Also assure that the cup does not move in hub 8 7 Drum Be sure that drum is free of grease and debris Measure to determine useful life The drum should not exceed OEMs maximum diameter specifications during the life of the reline maximum diameter is normally cast into the drum Check for cracks bell mouth hard spots hot spots heat checks glazing and blue areas See Appendix F for
42. r sealing surface Copyright 2007 APTA All rights reserved 23 APTA BTS SS RP 004 07 Approved 5 5 07 9 8 4 Preset the ABS and speedometer sensors If equipped If bus is equipped with a wheel end speedometer sensor it 1s normally located on the left side street side front tire However there are many variations so refer to OEMs recommendations for service and adjusting For either the ABS or speedometer to function properly the sensors must be in good condition and adjusted properly Service on both sensors is the same Inspect the sensors and wiring for damage Replace as necessary Set pre adjustment by pushing the sensors fully outboard When the wheel hub assembly and bearings are correctly installed the air gap for the sensors will properly position itself automatically 9 8 5 Install front hub drum and wheel e Carefully slide the hub or complete wheel end assembly over the spindle supporting it to avoid damaging the wheel seal and ABS sensor e Lightly coat the wheel bearing cone with grease or oil depending on application and slide the outer wheel bearing cone over the spindle and into place e Install the adjusting nut on the spindle and adjust finger tight e Install the drum and the wheel if not already installed e Tighten the adjusting nut to a torque of 200 ft Ibs while rotating the wheel e Back off the adjusting nut one full turn e Tighten the adjusting nut to 50 ft lbs while rotating the whee
43. rake drum to hub fasteners are tightened to the manufacturers specifications b Attach a dial indicator with its magnetic base to the hub or brake drum c Adjust the dial indicator so that its plunger or pointer is against the end of the spindle with its line of action approximately parallel to the axis of the spindle See Fig 1 a with tire assembly APTA BTS SS RP 004 07 Approved 5 5 07 d Grasp the wheel assembly at the 3 o clock and 9 o clock positions Push the wheel assembly in and out while oscillating it to seat the bearings Read bearing end play as the total indicator movement NOTE If end play is not within specification readjustment is required Step 9 RE ADJUSTMENT PROCEDURE Excessive End Play If end play is too loose remove the outer jam nut and pull the washer away from the inner adjusting nut but not off the spindle Tighten the inner adjust ing nut to the next alignment hole of the washer Reassemble the washer and re torque the outer jam nut Refer to Table 1 for torque values Verify end play with a dial indicator insufficient End Play lf end play is not present remove the outer jam nut and pull the washer away from the inner adjusting nut but not off the spindle Loosen the inner adjust ing nut to the next alignment hole of the washer Reassemble the washer and re torque the outer jam nut Refer to Table 1 for torque values Verify end play with a dial indicator
44. ren Re teeny ver ieer Saat waren vent nr nee teeny rar ieer Saereer en reper nr nee tenrny rr eer ey cantert ae 20 9 3 Install am chr Pi DUS NIG saya sessed eee cst E E oandecoyiiesaiacendacainuatdansemndicuaee 20 gt cs ets E 21 Greets ee on ein a re ee E i ENE rN Ce ID Se Ce Re Me NS 20 9 7 Install brake adjusters icici ccseiint tren a S T 21 6 Mis Ca Ke SO Sat ceca coalesce a acca a a oa cc a deans nae a aoa tote caa deans ate a aoa eceateee 21 9 7 lostall brake adjuster Nard wate ssiru aa e r A 22 9 8 Install front wheel bearings seals and hub assembly ccccccceeccceeeececceeeeeseseeeesseeeecceeeeeeeeeeeaeaaaaeeesees 23 9 9 Install rear wheel bearings seals anid Nib ASSembly cs ccciarcisseci dow st aiewlacaidsntaiths eiawn a EEA 25 PIOB aa ba Calo laememmeee epee ee noeteree ne anener enetene ce ve neeer nieteres nrant er snetene a veneenr niapentn nrenener snetene Ty reoeer nneteres rant ears entrmer 26 10 Burnishing testing and final inspection 2 0 ceeecesccccccceceeeeseeeceecceeaaseuseeeceeeeessaeesseeeceesessaaaasneeeeeess 21 OPS elo Ura o a Seacrest ne E ery imet Riatemetn rneceny nee neuen tri nee Meer nn teeters neereatenr Tints Saree tt re 27 MO 2 Perrormance CS waciebeteca ieee sera aai cers Asahi tiem tatiea si cees halle a teed caine sees A sale ala eek Siete a eh leases 27 TOS nane Oa a a A ACU Toe E 28 Copyright 2007 APTA All rights reserved 4 APTA BTS SS RP 004 07 Approved 5 5 07 1 Overview T
45. rn and still be usable If any portion of the brake surface exceeds the maximum diameter it must be discarded The maximum diameter cast into the back plate portions of the brake drum supersedes all published information Copyright 2007 APTA All rights reserved 40 APTA BTS SS RP 004 07 Approved 5 5 07 A3 Brake Drum Wear Information A Cracked Brake Drums 1 If drum is Mishandling Replace brake new drum Replace brake Heat checks drum Check brake connect together balance and brake and grow system see through drum Heavy Heat Check 2 If drum is used see picture at left Replace brake A AE 3 If used and Improper shoe oi Oee i prop contact the drum low mileage contact at the center of the shoe B Heat Checked Drums Problem eass Json Does not impair brake performance 1 Light Normal condition Brake drum may be turned within normal limits Imbalanced brake system Replace brake drum Check brake 2 Heavy dragging brakes or driver abuse balance brake return springs brake l lt is caused by constant heating adjustment and lining type within and cooling of brake surface vehicle combination Replace brake drum Shoes must Improper shoe contact contact the drum at the center of the shoe 3 Used low mileage Copyright 2007 APTA All rights reserved 4 APTA BTS SS RP 004 07 Approved 5 5 07 B1 Heat Check Light B2 Heat Check Heavy C Grooved Drums Problem Probable
46. s such as the angle of wear uneven lining wear and the condition of the brake block See Appendix D for examples of abnormal brake block wear and the likely cause When disassembling the brakes for reline note the condition of each brake component before disposing 7 2 Disassemble the foundation brake On steer axles turn the spindle to the fully locked position to gain access to the anchor pin locks 7 2 1 Remove the brake shoes Removal the anchor pins e Remove the anchor pin locking fasteners bolts snap ring anchor pin bracket e Use a soft drift and drive the anchor pins out Note Anchor pins may be difficult to remove Take care to avoid bending the spider when removing the anchor pins Frozen anchor pins should always be removed with a press Note Anchor pins should be replaced as part of every brake reline Removal of the brake shoes e With the anchor pins removed use a pry bar or suitable tool to remove the return springs Take care not to drop the shoe assemblies when removing the return springs e Remove the brake shoes from the spider and discard the return spring s 7 3 Remove the brake adjuster S cam and bushings Copyright 2007 APTA All rights reserved 15 APTA BTS SS RP 004 07 Approved 5 5 07 On steer axles turn the spindle to the fully locked position to gain access to the anchor pin locks Clean any buildup of dirt and grease from the end of the S cam and brake adjuster 7 3 1 R
47. sest flat perpendicular to the tang 2003 TMC ATA RP 618 4 Copyright 2007 APTA All rights reserved 49
48. t during the reline each property should establish a schedule for replacing these components based on the local operating conditions and usage history 5 1 Vehicle brake and maintenance history This Recommended Practice for Front Rear axle brake reline and maintenance also applies to components of the system that do not have wear indications but are inspected visually or require disassembly To determine a proactive replacement schedule use the manufacturers recommendations for component replacement rebuild and or the agency s component history These may be based on mileage brake cycles or time They may include variables such as climatic considerations unique operating parameters or a combination of both The replacement schedules will vary from agency to agency Any historical data must be accurate updated as required and meet the challenge of consistent performance reliability and repeatability Agencies that have the expertise of data collection evaluation and mechanical knowledge can use this historical data to schedule brake system component replacement rebuild intervals If historical data is unavailable a program of data collection should be implemented for future needs However scheduled replacement rebuild intervals MUST NOT exceed the manufactures recommendations 5 2 Overall Performance Based Brake Test Copyright 2007 APTA All rights reserved 7 APTA BTS SS RP 004 07 Approved 5 5 07 A Performance
49. ter or other foundation brake parts as required to meet new or original specification o During pushrod travel measurements check camshaft for excessive movement and for normal return of the foundation brake during release 5 3 6 Brake Chamber o During pushrod travel measurements listen for air leaks in the brake chambers or other foundation brake components Additional or extended application of the brake system may be needed to meet DOT standards for air system leak tests o Inspect for dents bends alignment leaks pushrod return corrosion and missing caps Hardware o Check the condition of the clevis pin and yoke o Check the integrity of the return springs e Lining wear cam position e The position of the roller on the cam should be closely checked at every brake inspection The position of the roller on the s cam is directly related to brake block and drum wear Other factors such as stretched shoes and worn cam bushings may also affect cam to roller position Care must be taken when inspecting the brakes to ensure that the roller on the s cam will not lock or allow the s cam to cam over before the block wears out e Air hoses e Inspect for cracks kinks routing leaking chafing deterioration proper size and material e Visual Inspection of suspension steering components e Some braking complaints can be caused by steering and or suspension problems Worn damaged or misaligned steering suspension components can c

Download Pdf Manuals

image

Related Search

Related Contents

Computer Design Of Beams, Joists, and Rafters  MEDISANA MEDISANA TERMOMETRO FTC PT  BDP2900/77/78 Blu-ray Disc Player  Samsung ML-2540R Vartotojo vadovas  Betriebsanleitung Vibrationsplatte VP 1340  Guía de inicio rápido  

Copyright © All rights reserved.
Failed to retrieve file