Installation and Service Manual Dual Planetary Gearmotor Slim
Contents
1. MINOR and MAJOR and the fault must be cleared in order for the room to operate MINOR faults can be cleared by pushing and releasing the IN or OUT buttons on the wall touchpad FIGURE 12 page 4 After the problem has been repaired MAJOR faults must be cleared by pushing and releasing the SET STOPS CLEAR FAULTS button located the back of the wall touchpad FIGURE 10 page 4 Note For major faults the control must be overridden by following the EMERGENCY RETRACT MODE in the OVERRIDE MODE section on page 7 The control will then have to be re programmed by a dealer when the problem is repaired Fault Code Fault Type Stops not programmed Figure 13 FAULT CODES Possible Cause Possible Solutions Stops have not been set Stops were cleared Stops were improperly set Stops need to be programmed according to the PROGRAM MODE instructions starting on page 4 Run room in opposite direction If room continues to move in the opposite direction remove obstruction excessive weight in room or repair of damaged component If room stops moving in opposite direction observe fault code and refer to this chart Obstruction present Excessive system drag Page 6 of 11 3010002588 Rev 0E Installation and Service Manual Slim Rack Slide Out System Fault Diagnostics Troubleshooting continued FIGURE 13 FAULT CODES Fault Code Fault Type Possible Cause Possible Solutions Check all connections at control box and moto2. process Room moves approx 1 4 for every 30 40 degree turn of the wrench 3 Secure the room in place by either re installing the motors making sure the end of the retaining spring is re hooked to the motor spring clip FIGURE 6 or torque the motor retaining screw to 40 in lbs FIGURE 7 and the motor retainer is fully engaged or using a travel lock 2 x 4 cut to size etc SEE NOTE ON PREVIOUS PAGE ON SEATING MOTOR 4 Have the slide out room serviced by an O E M authorized dealer as soon as possible Do not operate room until service is complete as damage to the room may result Figure 9 Figure 8 Coupler a Fiqure 10 Ratchet inside motor access with socket on coupler 1217 E 7 St Mishawaka IN 46544 Mfr www powergearus com AAL Page 9 of 11 3010002588 Rev 0E Installation and Service Manual Slim Rack Slide Out System Wiring Information PIN 1 SWITCH POWER RED PIN 2 ROOM OR LOCK MOVEMENT LED GREEN PIN 3 FAULT CODE LED GRAY PIN 4 SERVICE CALIBRATION ORANGE PIN 5 MOTOR 1 SWITCH WHITE wiBLACK PIN 6 MOTOR 2 SWITCH WHITE wWiGREEN PIN 7 MOTOR 3 SWITCH WHITE WiRED PIN 8 MOTOR 4 SWITCH WHITE WIORANGE PIN 9 EXTEND SWITCH YELLOW PIN 10 RETRACT SWITCH BLUE PIN 11 ENGAGE PARK BRAKE LED BROWN PIN 12 LOW VOLTAGE LED PURPLE 1 a a a Note See FIGURE 23 below s a for touchpad reference to pins a 2 3 9 10 11 and 12 Figure 19 1510000195 contr
3. 1 page 1 in a clean and dry weather tight location that will keep it from being damaged but is easily accessible for service The control is not waterproof i 2 Determine location to mount TOUCHPAD FIGURE 12 page 4 Location needs to be in Figure 7 _ o view of slideout room and have minimum depth of 1 inside the wall Cut a 3 1 8 wide by 2 high rectangular opening in the wall paneling to mount the touchpad 3 Route and attach the touchpad harness FIGURE 19 page 9 to where the touchpad will be mounted After system has been programmed see PROGRAM MODE page 3 mount TOUCHPAD FIGURE 12 page 4 with two 2 screws 4 Route the motor sensor harnesses from the slideout room motors to the control box Mark the motor leads at both ends to aid in connections after routing harness Note t is important that the slideout motors be plugged in to the proper receptacle at the control box Please see the FIGURE 9 below for proper slide out motor designation Failure to Wire mustheszidsothatra properly connect the motors to the control will result in programming issues see FAULT minimum of 12 5 VDC is DIAGNOSIS TROUBLESHOOTING page 6 measured at the control while under a load 5 Route and attach the proper gauge wire from the control to the 12V DC battery See FIGURE 8 to the left It is recommended that this circuit be protected with a 30 amp fuse Figure 8 nformation is given as reference only Installation of the In Wall Sli
4. 6 repair the fault and repeat the PROGRAM MODE procedure starting with STEP 1 page 4 The control must be programmed correctly before it will operate in normal mode The IN stop must be programmed before the OUT stop 5 Re install the wall TOUCHPAD FIGURE 12 page 4 Programming of the control is now complete Installation Issues The control is equipped to help troubleshoot the system during installation Count the number of LED flashes and refer to the FAULT DIAGNOSTICS TROUBLESHOOTING section starting on page 6 of this manual If you are still having difficulties programming the system and prior to replacing the control verify that the system has been wired correctly and that the IN stop location was programmed before the OUT stop location See FIGURE 9 page 3 for proper designation of the motors Motor 1 or Motor 2 to the slideout control Operation Mode Please note e The slideout system will not function until the stops are properly set or faults are cleared e The GREEN LED FIGURE 12 page 4 indicates the system operation A solid GREEN LED indicates room movement e The RED LED FIGURE 12 page 4 indicates a fault or a problem with the system Refer to the FAULT DIAGNOSTICS TROUBLESHOOTING page 6 for additional information Prior to moving the slide out room e Make sure the engine or generator is running to ensure ample voltage is being supplied to the slide out system motors e Set the parking brake
5. 82 S0529 Encoder Test 2 Dual Planetary Gear Motor Sync with Control Box 1510000199 Power Gear Limited Warranty Power Gear Limited Warranty Policy Original equipment Power Gear warrants its manufacturer installed Power Gear and Kwikee brand products to be free of material and workmanship defects for two 2 years from the date of the original sale of the motor vehicle recreation vehicle RV in which they are installed provided that these products are installed and operated according to the purpose for which they were intended designed and specified This warranty does not cover product that is incorrectly installed or upon examination has been misused or abused by the vehicle owner Warranty coverage includes e Repair or replacement of the defective component s of the malfunctioning system Entire systems are not replaced unless either the faulty component is not replaceable or all components comprising the system are defective e Labor costs for the diagnosis and repair work associated with the repair or replacement of the defective component s by a licensed servicing center This warranty does not include payment or reimbursement of e Normal system maintenance and preventive maintenance e Mobile service or towing expenses related to field repairs and or the transportation of the vehicle to a repair facility e Living or travel related expenses incurred in the repair of the vehicle By filing a warranty claim in accordance wit
6. only be possible if there is access to this area 1 You will first need to follow steps 1 6 as detailed above 2 Using a 8 point star socket FIGURE 18 and alternating from one side to the other turn the 12 square drive tube to bring the room in A 15 mm 12 point socket is an option if the 1 2 8 point star socket is not available Use caution as the 15 mm Figure 18 8 point star socket 12 point socket does not fit as snug as the 1 2 8 point socket 3 When the room is retracted secure the room per step 8 above 1217E 7 St A 4 Have the slide out room serviced by a dealer as soon as possible Do not operate Mishawaka IN 46544 piar room until service is complete as damage to the room may result www powergearus com A a Li Page 8 of 11 3010002588 Rev OE Installation and Service Manual Slim Rack Slide Out System Override Modes continued Note It may also be possible to manually retract the room by using a ratchet and socket attached to the end of the coupler FIGURE 8 1 You will first need to follow steps 1 6 under the Manual Retract Mode section to remove the motor 2 Place a socket wrench with a 3 extension and 5 8 deep well socket FIGURE 9 through the motor access opening and seat the socket onto the coupler One man alternating from side to side of the room is able to retract a 1500 Ibs room with or without a ramp Note 1 person per side of the room 2 total with ratchet and socket will expedite the
7. AULT CODE and our website at ROOM OR LOCK MOVEMENT LED s will flash rapidly for 10 seconds to indicate that the override www powergearus com procedure failed After the 10 seconds of flashing the control will automatically default to FAULT CODE 1 see FAULT CODES FIGURE 13 and programming must be restarted Note The room control will need to be re programmed by the O E M authorized dealer after the system has been overridden of RED of GREEN flashes flashes A EMERGENCY RETRACT MODE Pf Use this procedure when there is NO loss of power or electrical problem with the system dics achat 1 Remove the touchpad FIGURE 12 page 4 from the wall 2 Prior to clearing the MAJOR fault record the number of RED and GREEN flashes FIGURE 12 Page 4 observed on the touchpad This information will help your dealer service center in troubleshooting the slideout system 3 Press and hold the SET STOPS CLEAR FAULTS button FIGURE 10 page 4 on the back for the touchpad for five 5 seconds Both RED and GREEN LED s will be on solid while this button is pressed After five 5 seconds the GREEN LED will begin flashing and the RED LED will remain lit 4 The unit is now ready to retract the room Press and hold the ROOM SLIDEOUT MOTOR buttons 1 and 2 on the back of the TOUCHPAD FIGURE 10 page 4 Caution It is very important to note that during this procedure the slideout control has NO stop locations Use another individual to assist in
8. Extending the room The engine or generator must be running or plugged into shore power Transmission must be in park or neutral if applicable Set the park brake if applicable and level the unit If equipped remove the transit bars If equipped turn on the on off switch or key Press and hold the OUT button FIGURE 12 page 4 There will be a slight delay before the room will begin to move this is normal Release the button when the room is fully extended and stops moving If equipped turn off the on off switch or key oe ey oo N Page 5 of 11 3010002588 Rev 0E A WARNING Always make sure that the slideout room path is clear of people and objects before and during operation of the slideout room Always keep away from the slide rails when the room is being operated The gear assembly may pinch or catch on loose clothing causing personal injury If you have any problems or questions please see the contact tab on our website at www powergearus com Installation and Service Manual Slim Rack Slide Out System Operation Mode continued Retracting the room i at ke E oe The engine or generator must be running or plugged into shore power Transmission must be in park or neutral if applicable Set the park brake if applicable and level the unit If equipped turn on the on off switch or key Press and hold the IN button FIGURE 12 page 4 There will be a slight del
9. FIG 6 pg 3 A flat head screw must be used 6b Repeat steps 1b 6b for the other side of the slide out room Proceed to step 3 Continued 3 Lift the slide room box into coach opening and push in until mounting flange meets exterior wall NOTE n some applications and interior mounting flange may be used Install mounting flange once C channel assemblies are properly installed 4 Verify that the weight of the room is supported by the floor rollers and not the slide out mechanism FIGURE 5 NOTE f the room is not completely supported by the floor rollers you will hear a slight popping sound as the room settles on to the rollers This is normal and there is nothing wrong with Figure 4a the system or the install Install Fixture 5 Secure the mounting flanges to the unit s side wall FIGURE 6 page 3 Alternate Installation instructions for VERTICAL CHANNEL ASSEMBLIES with two flanges After steps 1 5 above are complete it will be necessary to remove the inner flange FIGURE 7 page 3 from each side of the VERTICAL CHANNEL ASSEMBLIES before lifting the room into position Once room is in position reinstall removed flanges Installation of the VERTICAL CHANNEL ASSEMBLY is now complete Page 2 of 11 3010002588 Rev 0E Installation and Service Manual Slim Rack Slide Out System Installation Continued Figure 5 Figure 6a Drill Fixture Figure 6 Electrical Components 1 Mount the CONTROL BOX FIGURE
10. a da sult in death Figure 12 Touchpad Page 4 of 11 3010002588 Rev 0E A WARNING 1217 E 7 St VN Mishawaka IN 46544 eN www powergearus com ina i Always make sure that the slideout room path is clear of people and objects before and during operation of the slideout room Always keep away from the slide rails when the room is being operated The gear assembly may pinch or catch on loose clothing causing personal injury Installation and Service Manual Slim Rack Slide Out System Program Mode Continued 4 You are now ready to set the extended or OUT stop a Press and hold the same slideout motor buttons MOTOR 1 and MOTOR 2 as you did in STEP 3a page 4 b Press the IN or OUT button on the front of the wall TOUCHPAD FIGURE 12 page 4 depending upon direction of rail movement you desire c Move the room to the fully extended position d Press and release the SET STOPS CLEAR FAULT FIGURE 10 page 4 button on the back of the wall touchpad to program the extended stop position e f both LED s flash rapidly for one 1 second and then shut off the control has been programmed correctly and is now in normal operation mode If both LED s flash rapidly for 10 seconds the control has NOT been programmed correctly or the system is wired incorrectly The TOUCHPAD FIGURE 12 page 4 will flash the fault code that occurred during programming Refer to the FAULT DIAGNOSTICS TROUBLESHOOTING section page
11. ay before the room will begin to move this is normal Release the button when the room is fully retracted and stops moving If equipped turn off the on off switch or key If equipped install the transit bars Preventative Maintenance Your Power Gear slideout system has been designed to require very little maintenance To ensure the long life of your slideout system read and follow these few simple procedures e When the room is extended visually inspect the slide rail assemblies Check for excess build up of dirt or other foreign material remove any debris items that may be present e If the system squeaks or makes any noises blow out any debris from the gear rack arms and apply a dry lubricant to prevent and or stop squeaking Fault Diagnostics Troubleshooting This control has the ability to detect and display several faults When a fault is detected the room movement will stop and two 2 different LED s will flash in a pattern The FAULT CODE LED FIGURE 12 page 4 will flash RED a number of times corresponding to a specific fault code Refer to the TROUBLESHOOTING chart on page 7 to best determine what caused the fault The ROOM MOVEMENT LED FIGURE 12 page 4 will flash GREEN a number of times corresponding to which motor had the associated fault For example if you are seeing four 4 RED flashes and two 2 GREEN flashes it means that there is a motor fault on motor 2 There are two 2 types of faults
12. bulb seal at the top of the VERTICAL CHANNEL FIGURE 15 3 Pull down the bulb seal and remove the motor cover FIGURE 16 The motor cover may stick to the bulb seal Using a pick tool remove the end of the retaining spring from the motor spring clip FIGURE 17A If not equipped with a retaining spring loosen the motor retaining screw FIGURE 17B Unplug the motor from the harness and remove the motor by lifting it up and out Repeat steps 1 4 for the other side Push the room into the retracted position Secure the room in place by either re installing the motors making sure the end of the retaining spring is re hooked to the motor spring clip FIGURE 17A or torque the motor retaining screw to 40 in Ibs FIGURE 17B and the motor retainer is fully engaged or using a travel lock 2 x 4 cut to size etc SEE NOTE BELOW ON SEATING MOTOR 9 Have the slide out room serviced by the O E M authorized dealer as soon as possible Do not operate room until service is complete as damage to the room may result assembly may pinch or catch on loose clothing causing personal injury 4 W pE NOTE Motor shown as properly seated No gap between i novi Ib seal oS e meade Bue eee mounting bracket and block Motor Retaining Screw Figure 17A Figure 17B Note It may be possible to manually retract the room by accessing the 1 2 square drive tube at the bottom of each vertical channel assembly This will
13. creased above the rating Contact Power Gear with motor part number for more information on stall specs Slide system controls must come from Power Gear Controls supplied by other companies will void warranty Voltage supply must come from a 12VDC automotive RV type battery Page 1 of 11 3010002588 Rev 0E Installation and Service Manual Slim Rack Slide Out System Touchpad Harness Control j to Touchpad N cy y Vertical Channel ae p O Control Box Harness Control to Motor Figure 2 Power Gear Slim Rack Slideout System Components Installation Continued Mechanical Components 1 Install Power Gear approved floor rollers Consult roller manufacturer for proper installation instructions 2 For sealing the screws used to attach end brackets Power Gear recommends RTV silicone rubber gasket or closed cell foam gasket DO NOT use any type of sealant putty as this can intrude into the mechanism and possibly cause the system to malfunction OPTION A WITH INSTALLATION FIXTURE 1a An Installation Fixture FIG 4a is used to maintain even spacing between the upper and lower gear rack arms and the location of the end brackets Even spacing between the gear rack arms and the location of the end brackets is critical for proper operation of the slide out Installation Fixtures are reusable from system to system Installation Fixtures are not supplied with system and must be purchased from Power Gear to aid in assembly a
14. deout is now complete You are now ready to program the in and out stops see PROGRAM MODE page 4 M1 Motor 1 Road side of Motorhome M2 Motor 2 M2 Motor 2 Curb side of Motorhome M1 Motor 1 Figure 9 Proper designation of motors as M1 or M2 Page 3 of 11 3 010002588 Rev 0E A WARNING e Always make sure that the slideout room path is clear of people and objects before and during operation of the slideout room settings Installation and Service Manual Slim Rack Slide Out System Program Mode Use this procedure to initially set the IN and OUT stops or to change the current stop Note At any time during the program procedure the unit will exit program mode if the room has not been moved for two 2 minutes or if a fault is detected during programming The FAULT CODE and ROOM OR LOCK MOVEMENT LED s will flash rapidly for 10 seconds to indicate that the programming procedure failed After the 10 seconds of flashing the control e Always keep away from the slide rails when the room is being operated The gear assembly may pinch or catch on loose clothing causing personal injury will automatically default to FAULT CODE 1 see FAULT CODES page 7 and programming must be restarted 1 Ifthe TOUCHPAD FIGURE 12 is mounted to the wall remove it to access the buttons FIGURES 10 amp 11 on the back side 2 Press and hold the SET STOPS CLEAR FAULT FIGURE 10 button on the back of the wall to
15. determining when the room is retracted Damage to the room can occur if the room is retracted too far 5 Press the IN button on the front of the wall touchpad until the room is fully retracted If one side of the of the room needs to retract further in order to get a good seal VAVe 7 Se A press and hold the motor button corresponding to only the motor you want to move Mishawaka IN 46544 powelyear Press the IN button on the front of the touchpad to retract the room the remainder of www powergearus com Ar the way Page 7 of 11 3010002588 Rev 0E Installation and Service Manual Slim Rack Slide Out System Override Modes continued 6 Re install the wall touchpad 7 Take the unit to a dealer for repairs A WARNING Always make sure that the slideout room path is clear of people and objects before and B MANUAL EMERGENCY RETRACT MODE Use this procedure when the above procedures do not work during operation of the In the event that power is lost to the slide out motor s or OVERRIDE MODE A page 7 will slideout room not work the room can be manually retracted by following these steps 1 You will need to gain access from either the inside or outside which ever is more Always keep away from the convenient of the coach to the VERTICAL CHANNEL assembly by removing the OEM slide rails when the room is trim and flange pieces on the slideout room box being operated The gear 2 If applicable remove the top screw from the
16. fedar p Advanced jt Actuation Solutions IPPERT ene a T DUAL PLANETARY GEARMOTOR sam SYNC CONTROL t Figure 1 Control Box Installation amp Service Manual Slim Rack In Wall Slide Out System Control Box Part Number 1510000199 Copyright LCI Power Gear Issued December 2014 3010002588 Rev OE Installation and Service Manual Dual Planetary Gearmotor Slim Rack Slide Out System Introduction SYSTEM DESCRIPTION The Power Gear Slim Rack Slideout System is a rack and pinion design operated by a 12 Volt DC gearmotor The system is designed to actuate rooms up to 1500 pounds with a 30 stroke Room slide out systems rated for higher weight or longer strokes can be obtained Please contact Power Gear for application assistance MAJOR COMPONENTS CONTENTS Introduction 1 Installation 1 3 Program Mode 4 5 Installation Issues 5 Operation Mode 5 6 Preventative Maintenance 6 Fault Diagnostics 6 7 Troubleshooting 6 7 Override Mode 7 9 Wiring Diagram 10 Additional Reference Pub 11 Warranty 11 NOTE Slide out systems are engineered to provide years of trouble free service Changes to weight Installation stroke weight distribution rail Touchpad that mounts to the wall It allows room movement and provides end user feedback A specially designed control that gives the user full control of room movement in or out The control has programmable stops that stop the
17. h Power Gear s Warranty Administration Procedure service providers agree that the replacement part s will be provided to the vehicle owner at no cost and that the total labor charges for the completion of warranty repairs will be billed to Power Gear Accordingly under no circumstances will Power Gear reimburse the vehicle owner directly for costs covered under this warranty policy Warranty coverage runs concurrently with any vehicle warranty period provided by the manufacturer and is transfer able to subsequent owners Proof of original date of purchase of vehicle and if applicable subsequent owner s proof of purchase is required to confirm coverage Power Gear reserves the right to change the terms of our warranty policy at any time For the most current information on product warranty and our warranty claim procedure visit our website at www powergearus com Page 11 of 11
18. motor when the room is fully extended or retracted and the ability to detect faults for ease in troubleshooting Vertical channel with 12V DC gearmotor and gear rack arms that mount into the side wall opening and slide out room Harnesses to connect the touch pad and motors to control box sold separately Slideout Systems are equipped with a manual override that allows you to extend retract the room in the event of a loss of power Floor rollers not supplied by Power Gear Only floor rollers approved by Power Gear can be used with the system Contact Power Gear for recommended rollers position controller power supply GENERAL REQUIREMENTS seals slide toppers ramps rollers etc all have an effect on the performance of the system In order to secure warranty coverage each new application or changes s to existing applications must be audited and approved by Power Gear with a signed document Audits can be arranged by contacting your account representative P 1217 E 7 St EN Mishawaka IN 46544 ENa www powergearus com Fi aswel F Power and wiring must be such that there is not less than 10 5 running volts supplied at the motor leads under maximum load To ensure long trouble free life of the In Wall slide system a maximum amp draw per motor should be less than 40 of motor stall The system will operate at higher loads amp draws but system component life will be reduced as the amp draw per motor is in
19. nd reduce installation time 2a Place the slide out mechanism into the installation fixture FIG 4a and bring the assembly up to the side of the slide room box FIG 3 making sure that the end brackets are flush to the wall Figure 3 moving assy into and up against the outer flange of the room Be sure to keep the gear rack and the end position brackets level when mounting FIG 4 3a Secure each end bracket with four 4 flat head 10 screws FIG 6 pg 3 A flat head screw must be used 4a Repeat steps 1a 4a for the other side of the slide out room Proceed to step 3 OPTION B WITH DRILL FIXTURE 1b A Drill Fixture FIG 6a page 3 is used to pre drill the mounting holes for the end brackets and maintain even spacing between the upper and lower gear rack arms Even spacing between the gear rack arms and the location of the end brackets is critical for proper operation of the slide out Drill Fixtures are reusable from system to system Drill Fixtures are not supplied with system and must be purchased from Power Gear to aid in assembly and reduce installation End time 2b Position the drill fixture so that the bottom flange of the fixture is pulled up against the bottom of the room l E 3b Move the drill fixture out so that it is up flush against the outer room flange Figure 4 4b Drillall 16 holes 4 per end bracket with a 25 drill bit 5b Place the slide mechanism up to the side of the room and secure with flat head 10 screws
20. ol to touchpad harness PIN 1 BATT VOLTAGE PIN 2 BATT GROUND Figure 20 Power harness 1510000233 GND CH1 SENSOR GREEN CH2 SENSOR YELLOW GROUND SENSOR BLACK POWER SENSOR RED MOTOR LEAD 2 RED MOTOR 1 BLACK powelgeat ail DUAL PLANETARY GEARMOTOR SYNC CONTROL Power Gear P N 1510000199 CAUTION READ AND UNDERSTAND OPERATORS MANUAL BEFORE USING Other US Patents Pending Figure 21 US Patents 6 345 854 amp 6 695 813 11 ENGAGE PARK BRAKE LOW VOLTAGE mm FAULT CODE Parking START AND RUN COACH CONSULT MANUAL IF FLASHING brake connector 10 IN 9 ROOM OR LOCK MOVEMENT wus A WARNING Figure 22 Control Box 1510000199 CRUSH HAZAR Keep ople and objects clear t el i the si mee room j s operating Failure to FOmMDpDly could es sott or serious injury Figure 23 Touchpad Reference of pins 2 3 9 1 0 11 and 12 from FIGURE 19 above ENE Se Mishawaka IN 46544 Many vergpar Parking brake jumper www powergearus com noite sta 1510000237 00 Page 10 of 11 3010002588 Rev 0E Installation and Service Manual Slim Rack Slide Out System ADDITIONAL REFERENCE PUBLICATIONS LOCATED AT WWW POWERGEARUS COM Document Description 3010002679 Owner s Manual Slim Rack In Wall Slide out System 82 S0518 Trouble shooting for control box 1510000199 for In Wall Slim Rack Slide out System 82 S0528 Encoder Test 1 Dual Planetary Gear Motor Sync with Control Box 1510000199
21. r See wiring diagram on Page 9 FIGURE 21 Bad or loose connection s Check the harness for broken wires Major Motor Fault Defective harness Put 12 0 VDC to the motor if it does not Open or shorted motor run replace the motor See TIP sheet 82 S0518 for further troubleshooting Check 2 pin power connector at control See Minor Excessive Battery Incoming voltage to control is wiring diagram on Page 9 FIGURE 20 Ifthe Voltage 17 0 VDC or greater voltage is 17 0 VDC or higher contact O E M for power and ground supplies Parking brake not set if applicable e Set parking brake if applicable Ground signal lost at e Check for continuity to ground on wire parking brake connector on plugged into park brake connector at control box control box See Page 9 FIGURE 22 Park brake LED flashing Check 2 pin power harness at control box Incoming voltage to control boxis See wiring diagram on Page 9 FIGURE 20 COW vonage EED tasang below 12 0 VDC If the voltage is below 12 0 VDC contact O E M for power and ground supplies Override Mode ere In the event of component failure or loss of system power your slideout can be manually overridden and This tip sheet and other retracted for travel updated troubleshooting information can be found on Note At any time during the override procedure the unit will exit this mode if the room has not been moved for two 2 minutes or if a fault is detected during room movement The F
22. uchpad for five 5 seconds The FAULT CODE and ROOM MOVEMENT LED s will light while the button is held down After five 5 seconds the GREEN LED will begin flashing and the RED LED will remain lit FIGURE 12 3 You are now ready to set the retracted or IN stop The IN stop must be programmed first a Figure 10 Set Stops Clear Fault Button ROOM SLIDEOUT MOTOR MOTOR 4 MOTOR 3 MOTOR MOTOR JEARL Re yen ars tE any E NOTORS MOTORS MOTOR MOTOR TT FF i a Figure 11 Room Slideout Motor Buttons Press and hold the slideout room motor buttons MOTOR 1 and MOTOR 2 FIGURE 11 on the back of the wall TOUCHPAD FIGURE 12 that correspond to the slideout motors you want to move These buttons correspond to the slideout room motors Press the IN or OUT button on the front of the wall TOUCHPAD depending upon direction of rail movement you desire Move the room to the fully retracted position Press and release the SET STOPS CLEAR FAULT FIGURE 10 button on the back of the wall touchpad to program the retracted stop position The RED LED will now start to flash and the GREEN LED FIGURE 12 will remain lit ROOM SLIDEOUT ENGAGE PARK BRAKE y LOW VOLTAGE START AND RUN COACH Mee m FAU T CODE CONSULT MANUAL IF FLASHING ou Red LED ROOM OR LOCK MOVEMENT Green LED K WARNING CRUSH HAZARD Keep people and objects of the slideoul roo comply could re clear m when Ag oie ponur
Download Pdf Manuals
Related Search