Service Manual
Contents
1. 3 Remove the four screws along the back of the unit the two on either side along the top edge and the two at the top of the glass retaining bracket on both sides Figure 3 4 Lay the Compact Fireplace on its back 5 Gently open the top panel laying it on the work sur face so that all of the components can easily be seen Figure 4 6 Locate the power cord and disconnect the wiring con nections noting their original locations NOTE A flat head screwdriver can be used to gently pry between the end of the connector and the switch to release the wires 7 With needle nose pliers grasp the power cord strain relief grommet from inside the back of the bottom panel and push while twisting to remove 8 Install the new power cord 9 Reassemble in the reverse order as above Figure 6 Bottom Panel FLICKER MOTOR amp FLICKER ROD REPLACEMENT Tools Required Phillips Head Screwdriver amp CAUTION If unit was operating prior to servicing allow at least 10 minutes for lights heating elements and top panel to cool off to avoid accidental burning of skin La WARNING Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons 1 Unplug the unit from power outlet 2 Remove the firebox from the back of the mantel by removing the retaining screws which secure the firebox brackets to the mantel 3 Remove the three screws along the back of the unit the t2. firebox brackets to the mantel 3 Remove the four screws along the back of the unit the two on either side along the top edge and the two at the top of the glass retaining bracket on both sides Figure 3 4 Lay the Compact Fireplace on its back 5 Gently open the top panel laying it on the work sur face so that all of the components can easily be seen Figure 4 6 Locate the remote control receiver and disconnect the wiring connections noting their original locations NOTE A flat head screwdriver can be used to gently pry between the end of the connector and the switch to release the wires 7 Release the receiver from the top panel by using needle nose pliers to depress the tab on the mounting standoffs and gently lift the receiver off 8 Properly orient and install the new remote control re ceiver and connect all of the wiring 9 Reassemble in the reverse order as above HEATER ASSEMBLY REPLACEMENT Tools Required Phillips Head Screwdriver Flat Head Screwdriver A CAUTION If unit was operating prior to servicing allow at least 10 minutes for lights heating elements and top panel to cool off to avoid accidental burning of skin La WARNING Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons 1 Unplug the unit from power outlet 2 Remove the firebox from the back of the mantel by removing the retaining screws which secure the firebox brackets
3. laying it on the work sur face so that all of the components can easily be seen Figure 8 6 Locate the LED lights along the back Each light is secured with four screws and there is a light filter that is sandwiched between the light assembly and the sheet metal bracket NOTE New light filters are not provided with replace ment lights and will need to be reinstalled in the original locations 7 Disconnect the wiring connections noting their original location 8 Properly orient and install the new LED lights and con nect all of the wiring 9 Reassemble in the reverse order as above LOG SET ASSEMBLY REPLACEMENT Tools Required Phillips Head Screwdriver A CAUTION If unit was operating prior to servicing allow at least 10 minutes for lights heating elements and top panel to cool off to avoid accidental burning of skin A WARNING Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons 1 Unplug the unit from power outlet 2 Remove the firebox from the back of the mantel by removing the retaining screws which secure the firebox brackets to the mantel 3 Remove the two screws on each side of the firebox that secure the log set to the outside panels 4 Pull the front edge of the plastic Ember Bed or plastic grate up and forward until the rear tab releases from the ledge located at the bottom of the Partially Reflect ive Panel Figure 9 IMPORTANT O
4. to turn fireplace on push the OFF button to turn the fireplace off NOTE Before attempting any operation with the remote control pull the plastic insulator strip out from between the remote casing and battery cover Figure 5 Remote Control Initialization Reprogram In the event that your remote control ceases to operate your fireplace follow these steps to reinitialize the remote control and the remote control receiver in the fireplace 1 Place the 3 Position Switch Figure 1A in the OFF O position 2 Wait a minimum of 5 seconds and then place the 3 Po sition Switch in the Remote Control position 3 Within 10 seconds of changing the switch position press the ON button located on the remote control Figure 2 This will synchronize the remote control and the fireplace receiver NOTE You will have only 10 seconds to perform this last step Failure to do so will result in these steps needing to be followed again Battery Replacement To replace the battery 1 Slide battery cover open on the remote control Figure 2 2 Correctly install one 12 Volt A23 battery in the battery holder 3 Close the battery cover AY Battery must be recycled or disposed of properly re Check with your Local Authority or Retailer for recyc ling advice in your area ON Button OFF Button Plastic Strip Battery Cover c IN MAINTENANCE A WARNING Disconnect power bef
5. P 14 LED Light Assembly 2 LED s 3001180100RP 6 Heater On Off Switch 2800070700RP 15 Felt Feet Pads setof4 8600140101RP fo Cord Set cies dca cued ln atatea aia 4100090203RP 16 Mounting L Bracket 9600870100RP 8 Flicker ROA 44 c4e0d4ae vba ma s 5902620100RP 9 Partially Reflective Panel 5902580300RP c IN 5 WIRING DIAGRAM IM E A EE i EA EF i 5 J LOG LED LIGHT HARNESS ss oaf Jt www dimplex com 3 POSITION SWITCH REPLACEMENT Tools Required Phillips Head Screwdriver Flat Head Screwdriver A CAUTION If unit was operating prior to servicing allow at least 10 minutes for lights heating elements and top panel to cool off to avoid accidental burning of skin A WARNING Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons 1 Unplug the unit from power outlet 2 Remove the firebox from the back of the mantel by removing the retai
6. X Dimplex Better solutions through innovation Service Manual Model Number DF2600 UL Part Number 690893XXXX IMPORTANT SAFETY INFORMATION Always read this manual first before attempting to service this fireplace For your safety always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage REV PCN DATE Dimplex North America Limited 1367 Industrial Road e Cambridge ON Canada N1R 7G8 00 13 AUG 13 1 888 346 7539 e www dimplex com In keeping with our policy of continuous product development we reserve the right to make changes without notice O 2011 Dimplex North America Limited 7400700100R00 TABLE OF CONTENTS OPERATION sac e e iaa tisa seat ee E b eee palti tenerse 3 MAINTENANCE os o ea e salii ata ads i a A ies cl dl eats a ide Ena 4 EXPLODED PARTS DIAGRAM a sassa wv cae pesos rss we EE e ee 5 REPLACEMENT PARIS setei 8 or bit oa ai ao en EE or ee ee aa e tor e eee eee 5 WIRING DIAGRAM cavseseusattetiect a a Dn pet a tin dn ea tea Eta e se i vada as 6 POSITION SWITCH REPLACEMENT css ce ere aia atat aie e e ua e de aia vii a 7 HEATER ON OFF SWITCH REPLACEMENT 0 000 eee eee ees F THERMOSTAT CONTROL REPLACEMENT 2 00002 sea ee o eee m aa mai 8 REMOTE RECEIVER REPLACEMENT odio dita dee ook rear En eee 8 HEATER ASSEMBLY REPLACEMENT mie aratate ee daewoo a edi cee ete Secu 8 POWER CORD REPLACEMENT ca eee trei i a cete osorn
7. ace on its back 5 Gently open the bottom panel laying it on the work sur face so that all of the components can easily be seen Figure 8 6 Locate the LED driver board and disconnect the wiring connections noting their original locations NOTE A flat head screwdriver can be used to gently pry between the end of the connector and the switch to release the wires 7 Release the driver board from the top panel by using needle nose pliers to depress the tab on the mounting standoffs and gently lift the driver board off 8 Properly orient and install the new LED driver board and connect all of the wiring 9 Reassemble in the reverse order as above LED LIGHT ASSEMBLY REPLACEMENT Tools Required Phillips Head Screwdriver A CAUTION If unit was operating prior to servicing allow at least 10 minutes for lights heating elements and top panel to cool off to avoid accidental burning of skin A WARNING Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons 1 Unplug the unit from power outlet 2 Remove the firebox from the back of the mantel by removing the retaining screws which secure the firebox brackets to the mantel 3 Remove the three screws along the back of the unit the two that hold the glass retaining bracket on both sides and the two on either side along the bottom edge Figure 6 4 Lay the Compact Fireplace on its back 5 Gently open the bottom panel
8. cturing or operation Defective Heater Assembly Replace Heater Assembly Heating element is glowing red Normal Operation Small glowing sections of the element are considered normal Defective heater assembly If larger glowing sections are causing the heater to trip the thermal cutout unplug unit discontinue use and replace heater assembly Heater fan runs continuously Normal Operation Small glowing sections of the element are considered normal Defective Heater On Off Switch Replace Heater On Off Switch Excessive noise with the heater Dirty Heater Assembly Ensure that exterior intake louvers and firebox cavity on are free of dirt dust Defective Heater Assembly Replace Heater Assembly Grinding or excessive noise with Flicker rod hitting or rubbing against Ensure rod is straight and mounted properly in the the heater off internal components bracket spinning freely away from other components Replace if necessary Defective Flicker Motor Replace Flicker Motor 13
9. e retaining screws which secure the firebox brackets to the mantel 3 Remove the four screws along the back of the unit the two on either side along the top edge and the two at the top of the glass retaining bracket on both sides Figure 3 4 Lay the Compact Fireplace on its back 5 Gently open the top panel laying it on the work sur face so that all of the components can easily be seen Figure 4 6 Locate the Heat On Off switch and disconnect the wir ing connections noting their original locations NOTE A flat head screwdriver can be used to gently pry between the end of the connector and the switch to release the wires 7 Depress the retainer clips on the rear of the switch and push the switch out through the opening 8 Properly orient and insert the new switch and connect all of the wiring 9 Reassemble in the reverse order as above Figure 4 Heater gt Assembly Remote Control Receiver 3 Position Switch Thermostat Heater On Off Switch Retaining Screws THERMOSTAT CONTROL REPLACEMENT Tools Required Phillips Head Screwdriver Flat Head Screwdriver amp CAUTION If unit was operating prior to servicing allow at least 10 minutes for lights heating elements and top panel to cool off to avoid accidental burning of skin La WARNING Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons 1 Unplug the unit from power
10. ning screws which secure the firebox brackets to the mantel 3 Remove the four screws along the back of the unit the two on either side along the top edge and the two at the top of the glass retaining bracket on both sides Figure 3 4 Lay the Compact Fireplace on its back 5 Gently open the top panel laying it on the work sur face so that all of the components can easily be seen Figure 4 6 Locate the Main Power switch and disconnect the wir ing connections noting their original locations NOTE A flat head screwdriver can be used to gently pry between the end of the connector and the switch to release the wires 7 Depress the retainer clips on the rear of the switch and push the switch out through the opening 8 Properly orient and insert the new switch and connect all of the wiring 9 Reassemble in the reverse order as above Figure 3 Glass Retaining Bracket i o E a e Te III lo 437 ada ge HEATER ON OFF SWITCH REPLACEMENT Tools Required Phillips Head Screwdriver Flat Head Screwdriver amp CAUTION If unit was operating prior to servicing allow at least 10 minutes for lights heating elements and top panel to cool off to avoid accidental burning of skin A WARNING Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons 1 Unplug the unit from power outlet 2 Remove the firebox from the back of the mantel by removing th
11. nly handle the Log Set by the Ember Bed NOTE Log Set fits tightly into firebox some force may be necessary to remove 5 Disconnect the wiring connections noting their original location 6 Remove the two screws on each side that secure the log set support brackets to the firebox remove the par tially reflective panel by sliding it out of the side chan nels towards the bottom Figure 9 7 Reassemble in the reverse order as above Figure 8 Back Ledge Log Ember Bed Rear Tab Front Side Section Edge 10 www dimplex com Support Bracket Screws 11 TROUBLESHOOTING GUIDE PROBLEM SOLUTION Circuit breaker trips or fuse Short in unit wiring Trace wiring in unit blows when unit is turned on Improper circuit current rating Additional appliances may exceed the current rating of the circuit breaker or fuse Plug unit into another outlet or install unit on a dedicated 15 amp circuit Unit turns on or off by itself Remote control has a similar frequency The remote control and the remote control receiver to other remotes in the area needs to be replaced Reinitialize the remote control Radio frequency disturbance from out to the remote control receiver after installation side sources Defective Remote Control Receiver Lights dim in room while the unit Unit is drawing close to circuit current Move the unit to another outlet or ins
12. nt When the switch is in the ON position the heater operates if the thermostat calls for heat NOTE The fan will continue running even when the heater is not when the Heater Switch is in the ON position C Heater Thermostat Control To adjust the temperature to your individual requirements turn the thermostat control clockwise all the way to turn on the heater When the room reaches the desired temper ature turn the thermostat knob counter clockwise until you hear a click Leave in this position to maintain the room temperature at this setting For additional heat turn clock wise until you hear the click again and the heater will turn on Resetting The Temperature Cutoff Switch Should the heater overheat an automatic cut out will turn the heater off and it will not come back on without being reset It can be reset by switching the 3 Position Switch to OFF and waiting 5 minutes before switching the unit back on A CAUTION If you need to continuously reset the heater unplug the unit and call technical support at 1 888 346 7539 NOTE The heater may emit a slight harmless odor when first used This odor is a normal condition caused by initial heating of internal heater parts and will not occur again Remote Operation The fireplace is supplied with an integrated On Off remote control NOTE Ensure that the fireplace 3 position switch is set to the remote control setting II To operate push the ON button
13. o rar cada 9 FLICKER MOTOR amp FLICKER ROD REPLACEMENT 200005 9 LED DRIVER BOARD REPLACEMENT ess conssdassansss cesar ici a 10 LED LIGHT ASSEMBLY REPLACEMENT aspassgercrrisses sia dec said 10 LOG SET ASSEMBLY REPLACEMENT 2242222 e ema mea i ee e ara e e pat e ae 10 TROUBLESHOOTING GUIDE moase aa des CREAs weet PRESS ai ei ees sel 12 Always use a qualified technician or service agency to repair this fireplace NOTE Procedures and techniques that are considered important enough to emphasize A CAUTION Procedures and techniques which if not carefully followed will result in damage to the equipment A WARNING Procedures and techniques which if not carefully followed will expose the user to the risk of fire serious injury or death 2 www dimplex com OPERATION Figure 1 The controls are located on the upper right of the fireplace Figure 1 A 3 Position Switch The switch has two ON positions marked with I and Il The position is for manual operation In this position the built in remote control is by passed The II position is for operating the unit with the provided remote control When in the II position the unit is operated with the ON and OFF buttons of the remote control When the switch is in the center position the unit is off B Heater ON OFF Switch The Heater ON OFF Switch supplies power to the heater fan and the heater eleme
14. ore attempting any maintenance or cleaning to reduce the risk of fire electric shock or damage to persons Glass Cleaning The glass is cleaned in the factory during the assembly operation During shipment installation handling etc the front glass panel may collect dust particles these can be removed by dusting lightly with a clean dry cloth To remove fingerprints or other marks the front glass panel can be cleaned with a damp cloth The front glass panel should be completely dried with a lint free cloth to prevent water spots To prevent scratching do not use abrasive cleaners or spray liquids on the clear door surface Compact Fireplace Surface Cleaning Use warm water only to clean painted surfaces of the Compact Fireplace Do not use abrasive cleaners Servicing Except for light bulb replacement and cleaning described above an authorized service representative should perform any other servicing www dimplex com EXPLODED PARTS DIAGRAM REPLACEMENT PARTS 1 Log SetAssembly 0439560300RP 10 FrontGlass 5902570200RP 2 FlickerMotor 2000220100RP 11 Remote Control 3000370500RP 3 Heater Assembly with Cutout 2203610100RP 12 Remote Control Reciever 3000380200RP 4 Thermostat with Knob 2600090100RP 13 LED Driver Board 3001170100RP 5 3 Position Switch 2800071100R
15. outlet 2 Remove the firebox from the back of the mantel by removing the retaining screws which secure the firebox brackets to the mantel 3 Remove the four screws along the back of the unit the two on either side along the top edge and the two at the top of the glass retaining bracket on both sides Figure 3 4 Lay the Compact Fireplace on its back 5 Gently open the top panel laying it on the work sur face so that all of the components can easily be seen Figure 4 6 Locate the thermostat assembly and disconnect the wiring connections noting their original locations NOTE A flat head screwdriver can be used to gently pry between the end of the connector and the switch to release the wires 7 Remove the two retaining screws from the mounting flange Figure 5 8 Properly orient and install the new thermostat assembly and connect all of the wiring 9 Reassemble in the reverse order as above REMOTE RECEIVER REPLACEMENT Tools Required Phillips Head Screwdriver Flat Head Screwdriver A CAUTION If unit was operating prior to servicing allow at least 10 minutes for lights heating elements and top panel to cool off to avoid accidental burning of skin A WARNING Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons 1 Unplug the unit from power outlet 2 Remove the firebox from the back of the mantel by removing the retaining screws which secure the
16. tall unit on a dedi is on rating cated 15 amp circuit Power cord gets warm Normal Operation The power cord may get slightly warm to the touch when the heater is on Defective power cord Replace power cord if cord gets hot to the touch Appearance Fireplace does not turn on Manu Improper operation Refer to Operation Section ally No incoming voltage from the electrical Check Fuse Breaker Panel wall socket The batteries in the remote control are Install new battery into the remote control Reinitalize dead remote if necessary Defective remote control Replace Remote Control and Remote Control Re ceiver reinitialize gt gt gt 12 www dimplex com PROBLEM CAUSE SOLUTION Heater o OSO Heater is not turning off Improper operation Defective Heater On Off Switch Heater is not turning on but Improper operation flame effect is still functioning Loose wiring Trace wiring in unit Defective Heater On Off Switch Replace Heater On Off Switch Defective Heater Assembly Replace Heater Assembly Heater is turning off after a Build up of dirt dust in Heater Assembly Ensure that exterior intake louvers and firebox cavity couple of minutes of operation are free of dirt dust Defective Heater Assembly Replace Heater Assembly Heater emits an odor Normal Operation Normal operation is when the heater emits an odor for a brief period after the heater is initially turned on The heater is burning off any dust accumulated during manufa
17. to the mantel 3 Remove the four screws along the back of the unit the two on either side along the top edge and the two at the top of the glass retaining bracket on both sides Figure 3 4 Lay the Compact Fireplace on its back 5 Gently open the top panel laying it on the work sur face so that all of the components can easily be seen Figure 4 6 Locate the heater assembly and disconnect the wiring connections noting their original locations NOTE A flat head screwdriver can be used to gently pry between the end of the connector and the switch to release the wires 7 Remove the 4 screws that secure the top panel to the heater assembly 8 Properly orient and install the new assembly and con nect all of the wiring 8 www dimplex com WARNING Ensure wires do not come in contact with moving parts by securing wires in wiring tie wraps 9 Reassemble in the reverse order as above POWER CORD REPLACEMENT Tools Required Phillips Head Screwdriver amp CAUTION If unit was operating prior to servicing allow at least 10 minutes for lights heating elements and top panel to cool off to avoid accidental burning of skin A WARNING Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons 1 Unplug the unit from power outlet 2 Remove the firebox from the back of the mantel by removing the retaining screws which secure the firebox brackets to the mantel
18. wo that hold the glass retaining bracket on both sides and the two on either side along the bottom edge Figure 6 4 Lay the Compact Fireplace on its back 5 Gently open the bottom panel laying it on the work sur face so that all of the components can easily be seen Figure 8 6 Locate the flicker motor and flicker rod 7 Locate and disconnect the 3 motor assembly wires go ing to the terminal block 8 Remove the 2 motor mounting screws 9 Separate the motor from the flicker connector and remove 10 Slide the flicker rod out of the snap in bushing and remove 11 Reassemble in the reverse order as above Figure 7 LED Driver Flicker Rod Flicker Motor Terminal Block LED DRIVER BOARD REPLACEMENT Tools Required Phillips Head Screwdriver A CAUTION If unit was operating prior to servicing allow at least 10 minutes for lights heating elements and top panel to cool off to avoid accidental burning of skin La WARNING Disconnect power before attempting any maintenance to reduce the risk of electric shock or damage to persons 1 Unplug the unit from power outlet 2 Remove the firebox from the back of the mantel by removing the retaining screws which secure the firebox brackets to the mantel 3 Remove the three screws along the back of the unit the two that hold the glass retaining bracket on both sides and the two on either side along the bottom edge Figure 6 4 Lay the Compact Firepl
Download Pdf Manuals
Related Search