Service Manual Wine chiller
Contents
1. Interior lighting on permanently or only when the door is open D ek Z CL Des ER A s 8 4 fe ge 6 Temperature display for the top compartment Temperature display for the bottom compartment Mode display Supercool on flashes when the presentation activation 10 Presentation mode pressing buttons 2 4 and 3 simultaneously activates and deactivates the presentation mode 11 Diagnosis pressing of all 4 temperature selection buttons activates the diagnosis mode A Child proof lock the buttons are only active after they have been pressed for 3 sec DGS TDS N 05 2006 O Electrolux 4 168 650 3 Refrigeration Cycle Diagram Beleuchtung 50 E NE Tirk ortat 7_ Elektronk PR per DL Ventilator kondens ator EM Temperatur CHIN EN Eu Hil LL LTTE HET CTT TCH ca Lam elle mwer dam pter 1 Wgl COLI OM CA ae JE ni on ERE EE EE gg I Trock enpatrone H tze Temp eraturfuhler unten Liina Kompressor Ventilator o Ventilator Ventilator DGS TDS N 05 2006 O Electrolux 2 168 650 4 Troubleshooting Appliance not working Appliance is not switched on The chilling temperature is insufficient Interior lighting not working Light does not go out Compressor 5 Min forced interruption for pressure compensation Plug is not inserted or i2. Ar Flachsteck hiss 4 800 Ar Flachsteck hiss d 5 0 5 fa Hakeieck hiss 4 000 168 650 4 Remove the sealing compound 5 Remove the protective covers 6 Loosen all 5 screws 7 Take hold of the rear panel through the slide opening and pull it towards you Thereby ensure that the cables do not get caught 8 When replacing insert the cable through the cable opening Initially insert the centre screw in the rear panel Finally seal the cable opening with sealing compound DGS TDS N 05 2006 Electrolux 20 E 6 3 8 Replacing the heating 1 Remove the rear panel 2 Remove the heating from the retainer 3 Remove the cable 6 3 9 Replacing the servomotor 1 Remove the rear panel 2 Loosen the servomotor retainer with the screwdriver and then pull it upwards 3 Remove the air flap arrow 4 Pull the servomotor upwards DGS TDS N 05 2006 Electrolux 21 168 650 6 3 10 Replacing the slide 1 Remove the rear panel 2 Remove the springs 3 Remove the slide and in doing so lightly press the panel outwards 6 3 11 Replacing the sensor 1 Remove the rear panel 2 Remove the sensor upwards from the retainer 3 Remove the cable 4 Do the same with the bottom sensor DGS TDS N 05 2006 Electrolux 22 168 650
3. Lace in the lines replace the leading in tube Art No 126221 9 Solder the lines in place DGS TDS N 05 2006 O Electrolux 15 168 650 6 3 3 Replace the capacitor 1 Warm up the capacitor connections with a soldering flame and loosen them 2 Loosen the screwed connections of the capacitor T NT LU II LEI s 3 Screw on a new capacitor 4 Reconnect the connections to the compressor and the dry cartridge A Risk of Explosion see 6 3 1 6 3 4 Always replacing dry cartridges 1 Cut off the dry cartridge connections directly above the dry cartridge with a special cutting tool II GIE ll Wi 2 Remove the dry cartridge 3 Position the new dry cartridge 4 Solder the dry cartridge on A Risk of Explosion see 6 3 1 DGS TDS N 05 2006 Electrolux 16 168 650 6 3 5 Replacing the compressor ml 1 Warm up the capacitor connections with a soldering flame and loosen them 2 Loosen the protective cover from the connecting box 3 Loosen the connections 4 Loosen the screwed connection and remove the compressor 5 Screw a new compressor on 6 Push on the connections and replace the protective cover 7 Solder the tubes on again A Risk of Explosion see 6 3 1 DGS TDS N 05 2006 Electrolux 17 168 650 6 3 6 Replacing the ventilator 1 Lift the cover with a screwdriver use the bottom slits lever the handle upward 2 2 Break cable out 3 Pull the ventilato
4. 8 168 650 6 Replacing Spare Parts 6 1 Door elements 6 1 1 Levelling out the door 1 An elongated hole is situated in the KS frame top and bottom which can be used to adjust the door height 2 An elongated hole is situated in the door top and bottom which can be used to adjust the door in a longitudinal direction Ensure that the gap between the niche and the door is the same all around 6 1 2 Replacing the door 1 Remove the bottom and top covers 2 Remove the internal screw from the top and the bottom 3 Loosen the external screw do not remove 4 Push the hinge out and then remove the door 5 Mount the new door in the reverse order DGS TDS N 05 2006 Electrolux 9 168 650 6 1 3 Inspecting the light switch 1 Switch the inside lighting of the door opening on see No 5 in the Operating Functions 2 The operating display shows OFF 3 Close the door the inside lighting should go off Refer to 4 and 5 if the light does not go off 4 Remove the operation see 6 2 1 and then check the sensor The sensor should be clearly bent as shown in the photo If necessary bend it carefully of replace the board 5 Check the position of the door magnet if the inside lighting still does not go off i e turn the magnet in the magnet housing 6 1 4 Replacing the door seal 1 Removal Left the seal at the corner and pull it off 2 Fitting Carefully press the seal in at the corners and travel al
5. A Electrolux Service Manual Distriparts Wine chiller menn arie arja rege m AER RR RE i F ra eae G ee ener EC t mores S Electrolux Distriparts Publ No Fitted wine chiller Muggenhofer Stra e 135 168 650 WEK 7 D 90429 Nurnberg 685 Germany EN Fax 49 0 911 323 1022 DGS TDS N Edition 05 06 Contents 1 Installing the Appliance EE 3 2 Operating FUNCIONS Eege 4 3 Refrigeration Cycle Dagram 5 EE elen ele ol le EE 6 5 Diagnosis Mode Presentation Mode rarrrnnnnrnnnnannnnnnnannnnnnnennnnnnnnn 8 6 Replace Spare Parts uuegeseeeggegeussgeegergegu egkresee esieegeng ELSE eege 9 DGS TDS N 05 2006 Electrolux 2 168 650 1 Installing the Appliance 1 Observe the correct width 550 mm CH version fittings 167603 600 mm EU version fittings 167678 2 Observe the climate classes SN 10 32 C N 16 32 ST 18 38 C 3 Electrical connection 220 240V 50 Hz alternating current It is imperative that the chiller be disconnected from the mains prior to work being carried out on the electrical system The electrical safety accidental contact protection is to be ensured by the installation DGS TDS N 05 2006 Electrolux 3 168 650 2 Operating Functions RON WO OO NO Switch appliance on off Temperature selection top area gt Can only be set if the Temperature selection bottom area gt display flashes Supercool mode
6. Error message F1 on the operation panel Error message F2 on the operation panel Possible cause Remedy Temperature setting Set correctly Sealing lip missing from false floor Fit sealing lip False floor missing Mount false floor Heating defect Inspect heating see Diagnosis Replace if defect Air flap control defective Inspect servomotor see diagnosis Air flap jams Remedy air flap malfunction Sensors exchanged Connect sensor correctly Increased atmospheric moisture Wipe off with a dry cloth set a little warmer Top sensor defect Replace sensor see 6 3 11 Appliance does not function in the emergency programme Bottom sensor defect Replace sensor see 6 3 11 Appliance does not function in the emergency programme DGS TDS N 05 2006 Electrolux 7 168 650 5 Diagnosis Mode Activation and deactivation by simultaneously activating the four buttons for the adjustment of the target values min 3 sec When the diagnosis mode is active tE alternates with the ACTUAL temperature of the top sensor in the left hand display and in the right hand display the ACTUAL temperature of the top sensor alternates with the consumer status The temperature displays in Diagnosis Mode are not the average compartment temperatures but the ACTUAL temperature at the sensor position The following functions are possible Compressor on off cold compartment Display CI CO Heating on off cold compartment Display HI
7. HO The heating function is reset to off after 10 minutes for safety reasons Flap open closed cold compartmentDisplay SI SO Ventilator on off cold compartment Display LI LO The Diagnosis Mode is automatically deactivated after 30 minutes for safety reasons The Diagnosis Mode can be deactivated at all times by switching the main switch off Presentation Mode An operation mode is possible for presentations by which the compressor ventilator heating and air flap are not switched The Presentation Mode is activated and deactivated by simultaneously pressing the button combination Target Value Adjustment top Supercool and target Value Adjustment bottom min 3 sec dE is briefly displayed in the left hand display after activation dA being briefly displayed in the left hand display after deactivation The target value adjustment lighting door switch and the door alarm remain active The Supercool function button only switches the LED but does not switch the compressor on and off The target values are shown in the right hand and left hand display as ACTUAL values In order to control the Presentation Mode operating mode the Supercool LED briefly illuminates every 5 seconds or it is briefly extinguished if the Supercool is activated A switching off and on by means of the main switch or a power failure does not result in a deactivation of the Presentation Mode DGS TDS N 05 2006 Electrolux
8. i e if a LED is defect the other LED on the same side Is also not illuminated DGS TDS N 05 2006 Electrolux 13 168 650 6 3 Refrigerating cycle The refrigerating cycle is only to be repaired in a workshop designed for this purpose The workplace must be well ventilated Soldering regulations and risk instructions R 600a All of the valid safety regulation in connection with the handling of combustible and explosive substances must be adhered to when installing the compressors in new and existing refrigerating systems The refrigerating agent must be avoided when evacuating a defective system 6 3 1 Evacuating the refrigerating agent A After suction is carried out on a R 600a cycle it is imperative that the system is flooded with dry nitrogen and not by air in order to avoid the formation of an explosive mixture The min suction and evacuation time should be 30 minutes You require an evacuation pump for the suction 4 A SE Risk of Explosion wr DGS TDS N 05 2006 Electrolux 14 168 650 6 3 2 Replacing the evaporator 1 Remove rear panel cover se 2 3 7 2 2 Open the rivet head by drilling it out with a 6 bit only the rivet head 3 Remove the board with the rest of the rivet 4 Loosen the evaporator screws 5 Warm up the connections with a soldering frame and loosen it NN EET 6 Pull the evaporator out of the inside retainer 7 Bend and screw on the new evaporator 8
9. ong the seal with the fingers DGS TDS N 05 2006 Electrolux 10 168 650 6 1 5 Replacing the handle 1 Lift the seal 2 Remove the cover cap 3 Loosen the screws with a Torx spanner 4 Remove the handle 5 Do not forget the plastic washers when mounting the handle Only tighten the screws with a maximum torque of 1 5 Nm risk of glass breakage DGS TDS N 05 2006 Electrolux 11 168 650 6 2 Replacing electrical elements It is imperative that the chiller be disconnected from the mains prior to work being carried out on the electrical system The electrical safety accidental contact protection is to be ensured by the installation 6 2 1 Replace operation 1 Remove the cover cap 2 Loosen the screws 3 Protect the buttons with adhesive tape 4 Loosen the printed circuit board screws 5 Carefully remove the printed circuit board from the clamp 6 Carefully remove the printed circuit board connector 7 When installing the operation ensure that the cable protects the cable before the soldering tip and that the sensor is not bent e DGS TDS N 05 2006 Electrolux 12 168 650 6 2 2 Replacing the lighting 1 Pull out the LED retainer with your fingers 2 Pull the clip back with your fingers and push the board upwards 3 Push the LED board out 4 Replace the LED board 5 Carefully reinsert the LED board A The LEDs are connected in series on the right hand side
10. r off Ensure that the rubber knob remains on the rear panel 4 Insert the new ventilator cable 5 Pull the rubber knob upwards with a pair of pliers until it latches into the ventilator DGS TDS N 05 2006 Electrolux 18 168 650 D 6 3 7 Removing the rear panel cover 1 Screw the electronics cover off 2 Remove all of the connectors 3 Electronics diagram rd Firs ees tet nd ale Baiteit gs Keompr Heiz k pe Sn ez Fearann oho Ir de Lupfe arlckesc Er vi Forster Ar Br s k Kalerdersoche DGS TDS N 05 2006 O Electrolux 19 Bodientwmil Stocker BL Temperatursensor Fach unten Sy Temperatursensor Fach oben anri lator Pech Vert acri pl WLS Seremetor weisse Litne Temparataseras Fach eben shwar ee TTempersumeree Fach unten Hai ee eee am v He amt Mear ffe ean Him Kompr Fees sw I Eeparette ben Mettes ble Printplatta VYEKT WEE 7 Pragrammile Name E3K1346 ve hex Farametersatzkennung 201 Paramseterliste siche Blatt 2 fir Stecker Ab blico March 1 21 3555 1 polig Dr S k ar Lumberg hd SAR 14012 Hd 2 54 3 polig fir Stecker Ab br 17397742 pobo fir Stecker AP Mr 178877 2 2polg fir Strecker Alex Connectors 9996 20 inp Ter mina oder PT YHP ri mp Ter minal fir Stecker Alx Connectors 9 2 A imp Ter minal oder PT WHERE ri mp Ter minal fa Hakeieck hise 2 0005 fa Hakeieck hise 6 200 Ar Flachsteck hisa dp
11. s loose Fuse Is defect Power outlet is defect Presentation mode is active Temperature is not correctly set Door was opened too long Ventilator defect Inspect door seal Appliance is next to a heat source Glass door is cracked or broken Glass door is mounted canted Compressor defect irregular operating sound LED is defect LED plug is not correctly inserted Magnet missing of incorrectly fitted Sensor bent magnetic field not effective Permanent mode activated DGS TDS N 05 2006 Electrolux 6 Switch appliance on Insert plug Check or replace fuse Have power supply defect repaired by an electrical specialist Deactivate Please refer to the operating functions Do not leave the door open for longer than 2 3 minutes alarm sounds after 5 minutes and can be deactivated by briefly pressing any button Replace ventilator see 6 3 6 Replace door seal see 6 1 4 Please refer to place of installation in the instruction manual Replace glass door see 6 1 2 Adjust glass door see 6 1 1 The repair is only to be carried out by a workshop designed for this purpose Risk of explosion Replace LED see 6 2 2 Inspect plug in connection see 6 2 2 Check light switch see 6 1 3 Align sensor see 6 1 3 Deactivate permanent mode 168 650 Fault Insufficient temperature difference top bottom Cooling temperature too cold Formation of condensation on the door
Download Pdf Manuals
Related Search