SERVICE MANUAL MODEL SSW-520-X
Contents
1. Dial tone 1s received if on a dial tone system LED illuminates The phone call is connected as provisioned through the Central Office PBX or Communication System The called party answers A normal speakerphone conversation is allowed Finish the conversation Press the Call Button again to hang up The called party hangs up LED goes out The call is terminated Using another phone call the number of the line to which the SSW 520 X is attached The internal ringer will sound indicating the incoming call Press the button to answer the phone and a normal speakerphone conversation should follow Press the button again when done CEECO Communication Equipment amp Engineering Company PROPRIETARY 8 0 SPECIFICATIONS INPUT POWER LOOP CURRENT IMPEDANCE RING SIGNALING OUTPUT ENVIRONMENTAL PROGRAMMING DIMENSIONS MOUNTING MEMORY RETENTION WEIGHT TYPE JACK ISSUE 4 0 C 0 PBX Comm Sys Line powered 27ma min 80ma max 600 ohms 90 120VAC 20Hz 4 0 to 6 0dbm Temperature Oc to 50c Humidity 20 90 non condensating Via DTMF keypad S W X 10 H X 3 1 2 D Vertical surface mount Non volatile memory retention Approximately 6 Pounds RJIIC CEECO 8 Communication Equipment amp Engineering Company PROPRIETARY 9 0 PARTS LIST QUANTITY ACCESSORIES PART NUMBER 301 018 301 054 SSW 520 X 660 100 6020 A 14123 1202. phone is attached to a communication system without dial tone it will simply be connected as wired The LED if provided will illuminate red at this time and the call will be connected as per the established connection via the C O PBX or Communication System When the call is completed press the Call Button again to hang up the phone The call will be terminated and the LED if provided will go out RECOMMENDED TOOLS AND TEST EQUIPMENT Volt Ohm Meter Security Tool CEECO part number 301 037 Flat Blade Screw Driver A Never install telephone wiring during a lightning storm B Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations C Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface D Use caution when installing or modifying telephone lines CEECO o Communication Equipment amp Engineering Company PROPRIETARY 6 0 ISSUE 4 0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS 6 1 6 2 6 3 6 4 6 5 6 6 6 7 6 8 6 9 Using a 301 037 security tool sold separately loosen and remove the security screw The security tool is for a standard 5 32 button head screw generally used on the framework of the phone booths Separate the cover assembly from the back plate assembly by pulling the bottom forward and pushing up The back plate assembly is designed to be moun
3. 17 11049 321 017 9023 301 037 ISSUE 4 0 DESCRIPTION MODULAR LINE CORD MODULAR CONNECTOR RJ11C SERVICE MANUAL CEECO SPK BOARD w o 945 005 Relay PUSH BUTTON SWITCH SPEAKER RINGER STAINLESS STEEL COVER STAINLESS STEEL BACKPLATE 1 4 20 X 3 4 SECURITY SCREW SECURITY TOOL CEECO 9 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 10 0 REPAIR AND RETURN INFORMATION 10 1 10 2 10 3 10 4 WARRANTY REPAIR Any device returned requiring warranty service repair or credit must be accompanied with a Return Material Authorization RMA FORM It must include return shipping instructions original purchase order number and special marking instruction A description of the trouble observed must be attached to the defective unit This information must be inside the shipping container DIRECT ALL INQUIRES TO CEECO Repair Department 519 West South Park Street Okeechobee FL 34972 863 357 0798 863 357 0006 FAX NON WARRANTY REPAIR CEECO will repair equipment out of warranty for a set charge plus parts The customer must pay the shipping costs for both directions RETURN FOR CREDIT Material may be returned for credit only with prior approval Material authorized for return is subject to a 20 restocking charge based on the manufacturer s list price Return Material Authorization must be requested no later than 60 days after original shipment CEECO 10 Communi
4. SSW 520 X ISSUE4 0 SERVICE MANUAL FOR MODEL SSW 520 X CUSTOM STAINLESS STEEL HANDS FREE WALL TELEPHONE EQUIPPED FOR RING DOWN OPERATION CEE Communication Equipment amp Engineering Company Serving the Telephone Industry Since 1930 519 West South Park Street Okeechobee FL 34972 Voice 863 357 0798 Fax 863 357 0006 ISSUE 4 0 IMPORTANT INFORMATION FOR CUSTOMER Please fill in before you continue The following information 1s necessary when calling CEECO for assistance MODEL NUMBER MODEL SSW 520 X STAINLESS STEEL HANDS FREE WALL TELEPHONE EQUIPPED FOR RING DOWN OPERATION For us to better serve you please have this information available when calling for technical support CEECO Communication Equipment amp Engineering Company 519 West South Park Street Okeechobee FL 34972 863 357 0798 Voice 863 357 0006 Fax CEECO 2 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 TABLE OF CONTENTS SECTION PAGE 1 0 INTRODUCTION 2222 ea re ER ie 4 2 0 GENERAL ati 4 4 0 OPERATION ri 5 5 0 RECOMMENDED TOOLS AND TEST EQUIPMENT s 0s0ssc 00020c0200 5 6 0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS 6 7 0 TESTING 7 8 0 SPECIFICA TIONS sicilia 8 9 0 PARTSLIST se 822er 9 10 0 REPAIR AND RETURN INFORMATION 0 cccccssscccsscccssccccssccsssccesscoes 10 ILO WARRANTY POLIC Y aan E 11 CEECO 3 Communication Equipment am
5. cation Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 11 0 WARRANTY POLICY GENERAL CEECO products are guaranteed to be free of defects n material and workmanship for a period of 365 days from the date of original purchase CEECO s obligation under this warranty 1s limited to repair or replacement of any part found to be defective by CEECO Under no circumstances shall CEECO be liable for loss damage cost of repair or consequential damages of any k nd which have been caused by neglect abuse acts of GOD or improper operation of equipment PRINTED CIRCUIT BOARDS Printed circuit boards should not be field repaired If a unit 1s found to be faulty replace it with another unit and return the faulty unit to CEECO for repair Modifications by anyone other than CEECO will void the warranty CEECO 11 Communication Equipment amp Engineering Company PROPRIETARY
6. p Engineering Company PROPRIETARY ISSUE 4 0 1 0 INTRODUCTION The practices in this manual provide installation and maintenance information for the CEECO Model SSW 520 X Stainless Steel Wall Telephone The information in this manual 1s subject to change without notification For information not included in this manual please call or write CEECO Customer Service 519 West South Park Street Okeechobee FL 34972 863 357 0798 863 357 0006 FAX 2 0 GENERAL 2 1 The CEECO Model SSW 520 X Hands free telephone 1s a sturdy vandal resistant Stainless Steel Speakerphone customized for manual ring down operation Instead of a hookswitch and handset the telephone 1s equipped with a Press to start Press to stop Call Button The button provides for the off hook on hook condition of the phone line in order for the external call equipment 1 e Central Office PBX or Communication System to direct the call as intended The phone itself will not dial anything It simply provides the off hook condition and talk path for two way handsfree communication The phone is well suited for ring down circuits inbound calls PBX direct connections or VoIP configurations that do not require a keypad CEECO 4 Communication Equipment amp Engineering Company PROPRIETARY 4 0 5 0 ISSUE 4 0 OPERATION To make a call press the Call Button located on the front of the telephone and wait to hear dial tone If the
7. ted on any flat vertical surface Four mounting holes are provided Run the inside station wire tip amp ring through the back plate assembly and terminate onto the terminal block on the back plate as depicted on the following page The use of a gas tube station protector is recommended The station ground should not exceed 50 ohms Plug together the line cord wires red amp green from the telephone assembly and the backplate by matching the marked surfaces of the connectors refer to diagram on next page Dress the lines cables away from the security screw Install the cover assembly by placing the two tabs into the two corresponding slots and secure the cover assembly by tightening the security screw TELEPHONE LINE WIRING DIAGRAM B FUSE 0 25 AMP 150 V gt SD L E Im H O N N O OUT A TN Le nn GE _ I x FUSE 0 25 AMP N A PROPRIETARI NS THIS DRAWING AND ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL AND IS THE EXCLUSIVE RED PROPERTY EECO AND MAY NOT BE COPIED REPRODU SCLOSED TO ANYONE IN ANY MANNER V OR USED FOR A URPOSE OTHER CIFIC PURPOSE FOR WHICH R dU HOUT THE PRIOR OF CERCO CEECO 6 Communication Equipment amp Engineering Company PROPRIETARY 7 0 TESTING Action Reaction Action Reaction Action Reaction Action Reaction ISSUE 4 0 Connect the phone to the line Press the Call Button
Download Pdf Manuals
Related Search