Home

SECURITY SYSTEM SMART SIREN II KIT - Harley

1. Left side electrical caddy Main fuse Security siren connector 142B Security siren Security siren receptacle Sounder disc Security siren antenna Figure 15 Siren Installation 2008 2013 FL Touring is04982 O O Po Frame tube above electrical bracket Adhesive backed hook fastener Siren antenna wire Plain backed loop fastener Penns Figure 16 Siren Antenna Installation 2008 2013 FL Touring Models 6 Remove the protective tape from the adhesive backing of the hook fastener 2 Attach the fastener to the frame in the cleaned area 7 Route the siren 3 pager antenna wire down the center of the installed fastener half Straighten the antenna along the length of the fastener NOTE In order for the pager antenna to work properly none of the small diameter portion should touch metal parts of the vehicle 8 Install the plain backed loop fastener 4 onto the hook fastener installed on the frame capturing the pager antenna wire to hold it firmly in place The remaining plain backed loop fastener is not used in this application It can be discarded 7 0f 15 NOTE Verify that the ignition is OFF before installing the main fuse 9 See the service manual to install the main fuse 10 Align the barbed studs on the side cover with the grom mets in the frame Push the side cover firmly into place 11 Install the left side saddlebag per the s
2. Figure 10 Electrical Bracket 2002 2007 FL Touring Models Penns 5 of 15 is01312 1 Siren harness lead 2 Protective cap Figure 11 Siren Wire Harness 2002 2007 FL Touring is01313 ue S oo ATCT 1 Security siren 2 Siren connector 142B is01579 AS ke Le 7 Gees 1 Electrical bracket 2 Siren 3 Siren antenna wire Figure 13 Slide Siren into Place 2002 2007 FL Touring is01581 1 Siren 2 Electrical bracket 3 Sounder disc 4 Siren antenna wire 5 Adhesive backed hook fastener Figure 12 Insert Siren Connector 2002 2007 FL Touring 3 See Figure 11 Remove the siren harness lead 1 from the back of the electrical bracket Take the protective cap 2 off the security siren connector 142B 4 See Figure 12 Insert the security siren connector 142B 2 into the siren box receptacle until the connector latches securely 5 See Figure 13 Slide the siren 2 into place on the back of the electrical bracket 1 so the sounder disc faces out NOTE Make sure that the cables and conduit are properly routed so they are not pinched during assembly 6 Feed the siren pager antenna wire 3 rearward under the siren out the back of the electrical bracket J03842 Figure 14 Siren and Electrical Bracket Installed 2002 2007 FL Touring Models 7 See Figure 14 Install the electrical bracket assembly with siren back
3. J03842 NOTE When pulling the electrical caddy away from the vehicle make sure that the wiring connections are not disturbed Pull the caddy away only far enough to allow installing the siren 3 10 Get the siren 5 from the kit Tip the top of the electrical caddy 3 slightly away from the vehicle Turn the siren so the sounder disc 6 faces up and the wire receptacle is facing the vehicle as shown Remove the siren harness lead from behind the electrical caddy Remove the black dust cap from the security siren connector 142B Insert connector 142B into the siren receptacle until the connector latches securely Insert the siren into the back of the caddy beneath the ignition control module 4 Install but do not tighten the front electrical caddy screw and washer 2 Install the top electrical caddy screws and washers 7 Tighten the top screws to 100 in lbs 11 3 Nm Tighten the front screw to 50 in Ibs 5 6 Nm Route the siren pager antenna wire 8 a under the rearmost frame crossmember b up between the crossmember and the rear fender Clean the top surface of the crossmember with a 50 50 mixture of isopropyl alcohol and distilled water Allow to dry completely Remove the protective tape from the adhesive backing of the hook fastener 9 Attach the fastener to the cleaned area of the crossmember Route the siren pager antenna wire 8 down the center of the installed fastener half Straighten
4. PARTS is01588a Figure 26 Service Parts Smart Siren II Kit Table 2 Service Parts Item Description Quantity Part Number 1 Smart Siren II security system Not sold separately 2 Hook fastener adhesive backed 8 1 4 in x 1 1 2 in 210 x 38 mm Not sold separately 3 Loop fastener plain backed 2 8 1 4 in x 1 1 2 in 210 x 38 mm 59274 01 Item mentioned in text A Battery 9 volt NIMH 69309 10 J03842 15 of 15
5. flammable and highly explosive which could result in death or serious injury 00330a 2 Remove the fuel cap Remove the fuel filler boot Save the boot for installation Install the fuel cap NOTE See Figure 3 The security siren connector is a three wire connector Do not confuse this connector with the two wire connector 3 tied to the harness except on California models 3 Locate the security siren connector 2 at the end of the harness lead that wraps around the top of the fuel tank Disconnect the fuel pump and sender connector 1 to free the security siren connector The protective cap and cable strap on the security siren connector can be discarded 4 See Figure 6 Remove the flanged hex nut 2 and flat washer 3 that retain the passenger seat 1 Remove seat is01308 1 Passenger seat 2 Flanged hex nut 3 Flat washer Figure 6 Remove Passenger Seat 2006 2007 VRSCR 3 of 15 is01309 1 Rear outer fender 2 Hex head screw 4 3 Spacer washer 4 Figure 7 Fender Mounting Fasteners 2006 2007 VRSCR 5 See Figure 7 Remove the four hex head screws 2 and spacer washers 3 that retain the rear outer fender 1 Slide the fender back Lift to remove 6 See Figure 4 Route the siren harness lead out from under the right side of the fender Get the siren 1 from the kit Insert connector 142B 2 into the siren receptacle until the connector latches secure
6. not used in this application It can be discarded 12 Slide the passenger seat under the grab strap Engage the mounting tab on the fender into the slot in the under side of the seat Make sure that harnesses are not pinched under the passenger seat frame IWIN NIN After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b 13 Fasten the passenger seat with the rider seat retaining post at the right front and the seat mounting nut and washer at the left front Tighten the nuts to 97 150 in Ibs 11 17 Nm NOTE Verify that the ignition is OFF before installing the main fuse 14 Install main fuse J03842 is05233a Main harness lead Security siren connector 142B Siren Sounder disc Cleaned area of frame Antenna wire Main harness Figure 9 Secure Siren Box 2007 Later VRSCA VRSCD VRSCF Models Oo a Na 2002 2007 FL Touring Models 1 Remove the right side saddlebag per the service manual Gently pull the side cover from the frame downtubes 2 See Figure 10 Remove the two flange nuts 2 from the electrical bracket 1 Pull the bracket assembly with the Electronic Control Module ECM and connector attached away from the side of the battery box is01311 Electrical bracket Flange nuts 2 Electronic control module ECM ECM connector
7. onto the studs on the side of the battery box Install the two flange nuts onto the studs Tighten the nuts to 36 48 in lbs 4 1 5 4 Nm 8 Clean the outboard surface of the frame tube above the electrical bracket with a 50 50 mixture of isopropyl alcohol and distilled water Allow to dry completely 9 See Figure 26 Remove the protective tape from the adhesive backing of the hook fastener 2 Attach the fastener to the frame in the cleaned area 10 Route the siren 1 pager antenna wire down the center of the installed fastener half Straighten the pager antenna along the length of the fastener NOTE In order for the pager antenna to work properly none of the small diameter portion should touch metal parts of the vehicle 6 of 15 11 Install the plain backed loop fastener 3 onto the hook fastener installed on the frame capturing the pager antenna wire to hold it firmly in place NOTE The remaining plain backed loop fastener is not used in this application It can be discarded 12 Align the barbed studs on the side cover with the grom mets in the frame Push the side cover firmly into place 13 Install the right side saddlebag per the service manual NOTE Verify that the ignition is OFF before installing the main fuse or attaching the battery cables 14 For 2004 2007 models See the service manual to install the main fuse For 2002 2003 models See the service manual to attach the battery cables Apply a ligh
8. the passenger seat with the flanged hex nut and flat washer removed earlier Tighten to 15 19 ft lbs 20 25 Nm 15 Remove the fuel cap Install the fuel filler boot Install the fuel cap NOTICE When closing the seat make sure the ignition switch is in the FUEL position If the ignition switch is in any other position when the seat is closed the seat latch mechanism could be damaged 00196a WARNING After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b 16 See the service manual to close the seat NOTE Verify that the ignition is OFF before installing the main fuse 17 Install the main fuse per the service manual 2007 Later VRSCA VRSCD X VRSCF Models 1 Open the seat 2 Remove the passenger seat pillion mounting nut and washer at the left front of the seat Remove the rider seat retaining post at the right front 3 Slide the pillion forward slightly to detach it from the mounting tab on the fender Slide the pillion back and out from under the grab strap Lift the pillion away from the vehicle 4 See Figure 9 Locate the three wire security siren con nector 142B 2 tied back to the harness lead 1 that travels alongside the TSSM mounting caddy Cut the tape to free the connector and wires 5 Insert siren connector 142B into the siren receptacle until th
9. 1 clipped to the right side of the electrical compartment cover splash guard already removed in photo forward of the rear wheel Remove the two hex socket head screws with washers fastening the cover Remove the cover from the vehicle 3 Remove the siren connector 142B from the receptacle 3 near the top of the electrical panel 2 J03842 Harness clipped to cover Electrical panel Siren connector 142B receptacle Rear fork swing arm oe NaS Figure 21 Electrical Panel FXCW C Models Siren box Sounder disc Pocket on right side of electrical panel Rear fork swing arm PONS Figure 22 Siren Mounting FXCW C Models 4 Insert siren connector 142B into the siren box receptacle until the connector latches securely 5 See Figure 22 Position the siren box 1 with the harness connector toward the rear and the sounder disc 2 facing out Carefully snap the siren box into the pocket 3 on the right side of the electrical panel 6 See Figure 23 Route the siren pager antenna 1 upward to the rear of the siren box Route forward following the path of the wire bundle 3 along the right side of the vehicle battery 4 NOTE In order for the pager antenna to work properly none of the small diameter portion 2 should touch metal parts of the vehicle 10 of 15 7 Tuck the pager antenna within the cable straps 5 that secure the wire bundle if possible If not secure
10. 106 2 in Ibs 8 12 Nm Remove the fuel cap Install the fuel filler boot Install the fuel cap 10 Clean the area on the frame 5 forward of the slot 4 along the space to the left of the fuel filler boot with a 50 50 mixture of isopropyl alcohol and distilled water Allow to dry completely 11 See Figure 26 Remove the protective tape from the adhesive backing of the hook fastener 2 Attach the fastener to the frame in the cleaned area 12 Route the siren 1 pager antenna wire down the center of the installed fastener half Straighten the pager antenna along the length of the fastener NOTE In order for the pager antenna to work properly none of the small diameter portion should touch metal parts of the vehicle 13 Install the plain backed loop fastener 3 onto the hook fastener installed on the frame capturing the pager antenna wire to hold it firmly in place NOTICE When closing the seat make sure the ignition switch is in the FUEL position If the ignition switch is in any other position when the seat is closed the seat latch mechanism could be damaged 00196a 14 See the service manual to close the seat NOTE Verify that the ignition is OFF before installing the main fuse 15 Install the main fuse per the service manual 2006 2007 VRSCR Models 1 Open the seat J03842 WARNING When servicing the fuel system do not smoke or allow open flame or sparks in the vicinity Gasoline is extremely
11. 42 Table 1 Models Item Description Quantity Fuse box Electrical caddy Body Control Module BCM Electrical Control Module ECM cover ECM cover screw Security siren connector 142B Battery tray CPN OP oa BP oO py Battery 9 Security siren 10 Sounder disc 11 Hook 3 beneath battery tray 12 Siren pager antenna 13 Right side rear frame upright 14 Cable strap 15 Large diameter portion of antenna 16 Small diameter portion of antenna 17 Frame rear upper crossmember 18 Adhesive backed hook fastener 19 Plain backed loop fastener 20 Direction of Inset views Figure 25 Siren Installation 2014 Later Sportster Models J03842 21 Views in direction of Arrow 19 ALL Models NOTE The siren may not function properly when first installed Nickel metal hydride NiMH rechargeable batteries discharge fairly rapidly when stored They will lose as much as 1 2 of their charge per day After a few months of storage at room temperature the batteries will be mostly discharged If stored for a much longer period without charging they may need a few charging cycles to regain their full capacity To charge the NiMH battery operate the vehicle for a minimum of four hours SIREN DIAGNOSTICS e Ifthe siren is armed and the internal siren battery is dead shorted discon
12. For Vehicles With Main Fuse AWARNING To prevent accidental vehicle start up which could cause death or serious injury remove main fuse before pro ceeding 00251b NOTE e For 2007 later vehicles equipped with security siren With security fob present turn ignition switch ON After J03842 Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled system is disarmed turn ignition switch OFF IMMEDI ATELY remove the main fuse per the service manual For 2006 earlier vehicles equipped with security siren Disarm the siren with the key fob or security code See the service manual to remove the main fuse For vehicles WITHOUT security siren See the service manual to remove the main fuse e All models except VRSC Remove seat Retain the seat and all mounting hardware For Vehicles With Main Circuit Breaker WARNING To prevent accidental vehicle start up which could cause death or serious injury disconnect battery cables negative cable first before proceeding 00307a WARNING Disconnect negative battery cable first If positive cable should contact ground with negative cable con nected the resulting sparks can cause a battery explosion which could result in death or serious injury 00049a z For vehicles equipped with security siren Disarm the siren with the key fob or security code All models except VRSC See the service manu
13. al to remove the seat Retain all seat mounting hardware Disconnect negative battery cable Disconnect positive battery cable Retain all seat mounting hardware VRSC models See the service manual to remove the main fuse Disconnect negative battery cable Disconnect positive battery cable 2 ALL models Turn ignition switch OFF unless already done INSTALLATION 2002 2006 VRSCA VRSCB VRSCD Models Open the seat wo See Figure 1 Remove the splash guard mud flap nuts w See Figure 2 Lower the mud flap from the installed posi tion Allow it to rest on the rear tire WARNING When servicing the fuel system do not smoke or allow open flame or sparks in the vicinity Gasoline is extremely flammable and highly explosive which could result in death or serious injury 00330a 1of15 Please dispose of materials responsibly 4 Remove the fuel cap Remove the fuel filler boot Save the boot for installation Install the fuel cap NOTE See Figure 3 The security siren connector is a three wire connector Do not confuse this connector with the two wire connector 3 tied to the harness except on California models 5 Locate the security siren connector 2 at the end of the harness lead that wraps around the top of the fuel tank Disconnect the fuel pump and sender connector 1 to free the security siren connector The protective cap and cable strap on the security siren connector can be discarded 6 See F
14. allow removal of the splash guard 2 Remove two bolts at the bottom of the splash guard Bend the upper right corner of the splash guard toward the rear tire Lift to unhook the splash guard from the tab on the rear fork Remove the guard from beneath the fender 8 of 15 is01316 tr 1 Siren mounting area 2 Siren connector 142B 3 Harness clip Figure 18 Siren Connector Softail Models EXCEPT FXCW C Rear Fender View with Rear Wheel Removed 3 See Figure 18 Remove the siren connector 142B 2 from the receptacle in the siren mounting area 1 of the electrical panel 4 Insert the siren connector 142B into the siren box receptacle until the connector latches securely 5 See Figure 19 Orient the siren 1 as shown with the harness connector 2 toward the bottom and the sounder disc 5 facing out Route the siren pager antenna wire 6 a upwards in front of the siren b forward of the upper rear fork tube and c through the opening in the upper left of the rear fender Carefully snap the siren into the electrical panel 6 Insert the siren harness lead 4 into the harness clip 3 to keep the harness clear of other components 7 If necessary secure the connector wiring to the electrical panel wiring with a cable strap not provided 8 See Figure 20 Gently pull the siren pager antenna wire upwards through the fender opening Lay the wire across the concave surface at th
15. cMOTOR HARLEY DAVIDSON WY J03842 INSTRUCTIONS REV 2013 05 23 SECURITY SYSTEM SMART SIREN II KIT GENERAL Kit Numbers 68328 06A 68328 06B Models For model fitment information see the P amp A retail catalog or the Parts and Accessories section of www harley davidson com English only Installation Requirements The vehicle must be equipped with a Harley Davidson Factory Security System before this kit can be installed See the P amp A retail catalog or the Parts and Accessories section of www harley davidson com English only for Factory Security System and model fitment information H D Electrical Contact Lubricant petroleum jelly or other cor rosion retardant material is required after battery cable discon nection H D Electrical Contact Lubricant is available from a Harley Davidson dealer WARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE Some model installations refer to service manual information A service manual for this year model vehicle may be required for this installation One is available from a Harley Davidson dealer Kit Contents See Figure 26 and Table 2 PREPARATION
16. dry completely 12 Remove the protective tape from the adhesive backing of the hook fastener 18 Attach the fastener to the cleaned area of the crossmember 13 Route the siren pager antenna wire down the center of the installed fastener half Straighten the pager antenna along the length of the fastener NOTE Loop the end of the pager antenna back if needed so it remains captured between the fastener components In order for the pager antenna to work properly none of the small diameter portion should touch metal parts of the vehicle 14 Install the plain backed loop fastener 19 onto the hook fastener installed on the crossmember capturing the pager antenna wire to hold it firmly in place on the underside of the crossmember The remaining plain backed loop fastener is not used in this application It can be discarded 15 Install the rear fender per the service manual NOTE Verify that the ignition is OFF before attaching the battery cables and installing the main fuse 16 Install the vehicle battery per the service manual Attach the positive battery cable Attach the negative battery cable Apply a light coat of H D electrical contact lubricant petro leum jelly or corrosion retardant material to battery ter minals 17 Install the ECM Install the ECM cover 18 Install the BCM into the electrical caddy 19 See the service manual to install the main fuse 20 Install left side cover 12 of 15 is074
17. e base of the electrical box Observe where the small diameter portion of the wire begins and where that point falls on the electrical box NOTE The hook and loop fastener may need to extend slightly into the fender opening to make sure that the entire small diameter portion of the pager antenna is protected from metal contact 9 Clean the concave surface at the base of the electrical box with a 50 50 mixture of isopropyl alcohol and distilled water Allow to dry completely J03842 10 See Figure 26 Remove the protective tape from the adhesive backing of the hook fastener 2 Attach the fastener to the cleaned area of the electrical box allowing it to extend as needed into the fender opening p AA a ou l IONET AA Do i Security siren Siren connector 142B Siren harness clip Siren harness lead Sounder disc Siren antenna wire O91 No Figure 19 Siren Mounting Softail Models EXCEPT FXCW C Diagnostic connector Electrical box Adhesive backed hook fastener Siren antenna wire oN Figure 20 Siren Antenna Mounting Softail Models EXCEPT FXCW C 11 Route the siren 1 pager antenna wire down the center of the installed fastener half Straighten the pager antenna along the length of the fastener NOTE In order for the pager antenna to work properly none of the small diameter portion should touch metal parts of the vehicle 12 Install
18. e connector latches securely 4of 15 6 With the sounder disc 4 facing out clip the siren onto the TSSM mounting caddy as shown 7 Clean the area on the frame forward of the TSSM mounting caddy with a 50 50 mixture of isopropyl alcohol and distilled water Allow to dry completely 8 Remove the protective tape from the adhesive backing of the hook fastener Figure 26 Item 2 Without covering any part of the warning label attach the fastener to the frame in the cleaned area 5 allowing it to extend as needed beyond the flat area NOTE In order for the pager antenna to work properly none of the small diameter portion should touch metal parts of the vehicle 9 Gently position the siren pager antenna wire 6 down the path along the TSSM caddy tucking it beneath the main harness 7 Route the siren pager antenna wire down the center of the installed fastener straightening the pager antenna along the length of the fastener Observe where the small diameter portion of the wire begins Verify that point is on the fastener 10 Install the plain backed loop fastener 3 onto the hook fastener installed on the frame capturing the pager antenna wire to hold it firmly in place Loop the end of the pager antenna back so it remains captured between the fastener components 11 If necessary secure the connector wiring to the existing wiring with a cable strap not provided NOTE The remaining plain backed loop fastener is
19. ervice manual 2014 Later FL Touring Models 1 See the service manual to remove the left side saddlebag Gently pull the side cover from the frame downtubes 2 See Figure 17 Remove the security siren connector 142B 3 from the retainer 2 on the electrical caddy 1 Insert security siren connector 142B into the security siren receptacle 5 until the connector latches securely 3 Slide the siren 4 into the pocket in the electrical caddy so the sounder disc 6 is toward the rear facing down 4 Clean the top surface of the electrical caddy with a 50 50 mixture of isopropyl alcohol and distilled water Allow to dry completely 5 Remove the protective tape from the adhesive backing of the hook fastener 8 Attach the fastener to the top of the caddy flush with the forward and outboard edges Fold the excess around the rear edge of the caddy 6 Route the siren pager antenna wire 7 a rearward under the siren b around the now empty siren connector retainer 2 and c over the top of the electrical caddy NOTE None of the small diameter portion of the pager antenna should touch metal parts of the vehicle 7 Route the pager antenna forward along the top of the caddy to the front edge close to the vehicle frame Loop back and route the pager antenna rearward over the installed hook fastener Make sure all of the smaller dia meter portion of the pager antenna is contained within the fastener 8 Install t
20. he plain backed loop fastener 9 onto the hook fastener capturing the smaller diameter portion of the pager antenna wire to hold it firmly in place The remaining plain backed loop fastener is not used in this application It can be discarded NOTE Make sure that the cables and conduit are properly routed so they are not pinched during assembly J03842 is07441 Electrical caddy Security siren connector retainer Security siren connector 142B Security siren Security siren receptacle Sounder disc Siren pager antenna wire Adhesive backed hook fastener OOS Oe ON aa Plain backed loop fastener Figure 17 Siren Installation 2014 Later FL Touring Models NOTE Verify that the ignition is OFF before installing the main fuse 9 See the service manual to install the main fuse 10 Align the barbed studs on the side cover with the grom mets in the frame Push the side cover firmly into place 11 Install the left side saddlebag per the service manual 2003 later Softail Models EXCEPT FXCW C 1 Models with saddlebags Remove the right side saddlebag per the service manual NOTE The siren connector is installed on an electrical panel under the rear fender on all Softail models The rear of the vehicle must be raised slightly to
21. igure 4 Route the siren harness lead out from under the right side of the fender Get the siren 1 from the kit Insert connector 142B 2 into the siren receptacle until the connector latches securely 7 With the sounder disc 3 facing the mud flap position the siren on the mud flap as shown in Figure 5 Make sure that the pager antenna lies in the groove alongside the connector and is not pinched Secure the siren 1 to the existing hook fasteners on the mud flap with the plain backed loop fastener 2 from the kit 8 See Figure 3 Feed the siren pager antenna wire upwards through the slot 4 in the frame is01303 is01304 Figure 2 Lower the Mud Flap 2002 2006 VRSCA B D J03842 is01575 Fuel pump and sender connector Security siren connector 142B under here Two wire connector 95B Slot 5 Attach antenna fastener in this location Ne Figure 3 Locate Connector 142B 2002 2006 VRSC Models Shown with Fuel Cap and Filler Boot Removed 1 Siren 2 Connector 142B 3 Sounder disc Figure 4 Install Siren Connector 2002 2006 VRSC Models 2 of 15 is01574 DOV Pa N 1 Siren 2 Plain backed loop fastener in kit 3 Hook fastener 2 on vehicle Figure 5 Secure Siren Box 2002 2006 VRSCA B D Models 9 Install the mud flap to the underside of the fender Install the mud flap nuts Tighten to 70 8
22. ions to prevent the security module from actuating the siren 2 Remove the siren box from the vehicle Refer to the siren installation procedures for the specific model in this instruction sheet J03842 3 Open the battery cover by inserting a flat blade screwdriver into one of the slots on the side of the siren box Press until one corner of the cover pops up slightly 4 Insert the screwdriver into the second slot Press until the cover pops open Remove the cover and gasket 5 Remove the old battery from the siren box Gently unfasten the snap connector from the battery Save the grease coating the terminals 6 Coat the terminals of the new NiMH nine volt battery and the snap connector completely with the grease from the old connection NOTE If not enough lubricant remains to cover the terminals com pletely H D Electrical Contact Lubricant is compatible It is available from a Harley Davidson dealer 7 Snap the connector onto the new battery Install the battery into the siren box 8 Set the siren box on a work surface with the battery opening facing up Position the gasket and battery cover onto the siren box with the rounded corners facing out 9 Press the cover down onto the siren box Press the tabs in with the screwdriver until the tabs snap into the slots in the box 10 Install the siren box into the vehicle 11 Dispose of the old NiMH battery in accordance with local regulations 14 0f 15 SERVICE
23. ly 7 See Figure 8 With the sounder disc 2 facing out clip the siren 1 onto the mud flap 3 as shown NOTE Verify that the outer fender tabs are latched with the inner fender locking tabs is01310 1 Siren 2 Sounder disc 3 Mud flap Figure 8 Secure Siren Box 2006 2007 VRSCR Models 8 Press down gently on the outer fender to seat the fender against the frame 9 Install the four screws and flat washers that retain the rear outer fender Tighten to 40 66 in Ibs 4 5 7 5 Nm J03842 10 Refer to Figure 3 Clean the area on the frame 5 forward of the slot 4 along the space to the left of the fuel filler boot with a 50 50 mixture of isopropyl alcohol and distilled water Allow to dry completely 11 See Figure 26 Remove the protective tape from the adhesive backing of the hook fastener 2 Attach the fastener to the frame in the cleaned area 12 Route the siren 1 pager antenna wire down the center of the installed fastener half Straighten the pager antenna along the length of the fastener NOTE In order for the pager antenna to work properly none of the small diameter portion should touch metal parts of the vehicle 13 Install the plain backed loop fastener 3 onto the hook fastener installed on the frame capturing the pager antenna wire to hold it firmly in place NOTE The remaining plain backed loop fastener is not used in this application It can be discarded 14 Install
24. nected or has been charging for a period longer than 24 hours the siren will respond with three chirps on arming instead of two e If the vehicle s charging system is producing less than 12 5 volts the internal siren battery may not charge e Ifthe siren does not chirp two or three times on a valid arming command from the security system the siren is either in chirpless mode not connected not working or 13 of 15 the siren wiring was opened or shorted while the siren was disarmed e Ifthe siren enters the self driven mode where it is powered from the siren s internal 9 volt battery the turn signal lamps may or may not alternately flash If the security system activates the siren the turn signal lamps will alternately flash If the siren has been armed and a security event occurs and the siren is in self driven mode the siren will alarm for 20 30 seconds then turn off for 5 10 seconds This alarm cycle will be repeated ten times if the siren is in the self driven mode SMART SIREN II BATTERY REPLACEMENT The siren s internal 9 volt battery is rechargeable It does not need frequent replacing Battery life under normal conditions is about three to six years NOTE When battery replacement is needed use only a nickel metal hydride NiMH 9 volt battery in the siren These batteries are widely available at local outlets To Replace the Battery 1 Refer to POWER DISCONNECT in the owner s manual Follow the instruct
25. t coat of H D electrical contact lubricant petroleum jelly or other corrosion retardant material to battery terminals WARNING After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b 15 See the service manual to install the seat 2008 2013 FL Touring Models 1 See the service manual to remove the left side saddlebag Gently pull the side cover from the frame downtubes 2 See Figure 15 Remove the security siren connector 142B 3 from the retainer on the electrical caddy Insert security siren connector 142B into the security siren receptacle 5 until the connector latches securely 3 Slide the siren into place on the left side of the electrical caddy so the sounder disc 6 faces out 4 Route the siren pager antenna wire rearward under the siren out the back of the electrical caddy NOTE Make sure that the cables and conduit are properly routed so they are not pinched during assembly 5 See Figure 16 Clean the outboard surface of the frame tube 1 above the electrical caddy with a 50 50 mixture of isopropyl alcohol and distilled water Allow to dry com pletely J03842 is04981
26. the ECM cover 4 Pull the ECM cover forward and out the left side of the vehicle 5 Remove the security siren connector 142B 6 from the retainer on the back of the electrical caddy Route the connector and wiring under the battery tray 7 to the right side of the vehicle 6 Remove the battery 8 from the vehicle per the service manual 7 Insert security siren connector 142B into the security siren 9 receptacle until the connector latches securely J03842 8 Snap the siren into the hooks 11 beneath the battery tray so the sounder disc 10 is toward the left front facing downward NOTES e Make sure that the cables and conduit are properly routed so they are not pinched during assembly In order for the pager antenna to work properly none of the small diameter portion should touch metal parts of the vehicle 9 Route the siren pager antenna wire 12 over to the right side of the vehicle frame Fasten to the top of the rear frame upright 13 away from the belt guard with a cable strap Item 14 not supplied at the outward bend 10 Bring the end of the large diameter portion 15 of the pager antenna to the underside of the frame rear upper crossmember 17 Observe where the small diameter portion 16 of the wire begins and ends on the cross member 11 Clean the entire area on the underside of the frame rear upper crossmember with a 50 50 mixture of isopropyl alcohol and distilled water Allow to
27. the pager antenna to the wiring with new cable straps not provided 8 Install the electrical compartment cover Install the screws and washers removed earlier Tighten the screws to 36 60 in Ibs 4 1 6 8 Nm 9 See the service manual to a Set the fender into position b Loosely install the fender mounting hardware c Tighten the fender mounting hardware in the indic ated sequence to the specified torque d Connect the rear wiring harness connector 7 halves NOTE Verify that the ignition is OFF before attaching the negative battery cable 10 See the service manual to attach the battery cables Apply a light coat of H D electrical contact lubricant petroleum jelly or other corrosion retardant material to battery ter minals AWARNING After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b 11 See the service manual to install the seat T js05262 Siren antenna Small diameter portion of antenna Vehicle wire bundle Vehicle battery Cable straps Figure 23 Siren Antenna Mounting FXCW C Models oP ONS 2004 later Dyna Models 1 See Figure 24 Firmly grasp both sides of the electrical caddy cover 1 Pull out to remove 2 Remove the front electrical caddy screw and washer 2 Remove the two top electrical caddy screws and washers 7
28. the pager antenna along the length of the fastener NOTE In order for the pager antenna to work properly none of the small diameter portion should touch metal parts of the vehicle 11 Install the plain backed loop fastener 10 onto the hook fastener installed on the crossmember capturing the pager antenna wire to hold it firmly in place NOTE Verify that the ignition is OFF before installing the main fuse 12 13 See the service manual to install the main fuse Install the electrical caddy cover 11 of 15 is01587 Cover Front fastener Electrical caddy Ignition module Siren Sounder disc Top fasteners 2 Siren antenna wire Adhesive backed hook fastener 10 Plain backed loop fastener OHMNBARYONS Figure 24 Install Siren in Electrical Caddy Dyna Models 2014 Later Sportster Models 1 Remove the left side cover from the frame downtubes 2 Remove the rear fender per the service manual a Remove the lower shock absorber bolts b Raise the motorcycle to lower the rear wheel c Disconnect rear lighting connectors 18 19 and 40 d While supporting the fender remove attaching hard ware e Carefully remove the rear fender with attached license plate bracket tail lamp base and wire harness 3 See Figure 25 Pull the fuse box 1 away from the oil tank Remove the Body Control Module BCM 3 from the electrical caddy 2 4 Remove the screw 5 retaining
29. the plain backed loop fastener 3 onto the hook fastener installed on the frame capturing the pager antenna wire to hold it firmly in place NOTE The remaining plain backed loop fastener is not used in this application It can be discarded 9 of 15 13 Hook the slot at the top of the splash guard over the tab on the rear fork Install the guard with the two screws removed earlier Tighten securely 14 Models with saddlebags Install the right side saddlebag per the service manual NOTE Verify that the ignition is OFF before attaching the negative battery cable 15 See the service manual to attach the battery cables Apply a light coat of H D electrical contact lubricant petroleum jelly or other corrosion retardant material to battery ter minals IWIN IN After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b 16 See the service manual to install the seat 2008 later FXCW C Rocker Models NOTE Record fender wire routing and hardware locations before removal 1 Remove the rear fender from the vehicle See the service manual to a Disconnect the rear wiring harness connector 7 halves b Remove the lower fender mounting bolts and washers c Remove the upper fender mounting screws and washers d Remove the fender 2 See Figure 21 Unfasten the harness

SECURITY SYSTEM SMART SIREN II KIT - Harley

Contents

Download Pdf Manuals

Related Search

Related Contents