Home

PDF Manual

image

Contents

1. The paddle switch is used to optionally advance the backgauge after the side load is completed Use the hardware supplied to mount the switch to the top rail of the loader Hang the switch down so that the paddle linkage will snap the yoke trip arm in one direction as the paddle enters onto the table and the switch will trip back to its normal position as the paddle exits NOTE The paddle switch DOES NOT defeat backgauge drive It is used strictly to sense the completion of the paper load so that the gauge may advance to the first cut location automatically If the paddle switch is not hooked up then the option of AUTO ADVANCE will not be offered in the MODIFICATION ROUTINE see the OPERATOR S MANUAL If side loading is used a separate photo switch JAM UP SENSE should be mounted to sense across the throat of the side loader to sense the presence of any paper or obstruction The contacts should conduct current only when there is no obstruction which could cause a Jam up of the gauge This photo switch should be wired in SERIES with the CLAMP UP switch Run the wires back to the base console Remove the wire to the CLAMP UP SWITCH at terminal 10 and attach it to one of the photo switch wires with a wire nut Attach the other wire from the photo switch to terminal 10 When the wiring is complete no terminal should have more than one wire attached to it The motor will be disabled whenever there is anything blocking the JAM UP SENSE photo
2. MICROCUT Answer the question If YES is pressed MICROCUT will drive the backgauge to the full rear of the table at the end of each job sequence IF you answered YES above do you want MICROCUT to automatically move to the first cut after side loading is done PADDLE SENSE SWITCH REQUIRED Press YES to have the backlighting for the prompt display ON Press NO to turn it off MICROCUT now knows what type of machine it has been installed on and is ready to use SIDE LOADING YES OR NO AUTO ADVANCE AFTER SIDE LOAD PROMPT DISPLAY BACKLIGHTING Y N TURN POWER OFF RESTART TURN THE POWER OFF AND BACK ON The display will read PRESS AUTOMATIC TO START You are ready to operate MICROCUT O 23 ADDENDUM TO SETTING UP MICROCUT 1 Make sure all power is OFF to MICROCUT Make sure that the backgauge is in the middle of the table 2 Supply the 110 VAC power to MICROCUT Use the ON OFF switch to power ON the display 3 If the display says PRESS AUTOMATIC TO START DON T press the AUTOMATIC key but instead press and hold any NUMBER key and then press the PROGRAM key Release both keys and this will take you into the SETUP ROUTINE The first 24 lights in the base console should be on If not stop here and see DIAGNOSTIC LIGHTS in the SERVICE MANUAL If all lights are on press the YES key The display will show The memory testis non destructive the job memory won t be altered Press YES or NO to this opt
3. OPTION 1 PROGRAM KEY LIT IN PROGRAM OR REVIEW MODES INSTRUCTION DISPLAY READS JOB 954 CUT 010 30 000 The display will show JOB 954 CUT 010 Press the NO key INSERT CUT The display will show JOB 954 CUT 010 Press the YES key DELETE CUT The cut is deleted from the job memory Use the ENTER or LAST key to locate the cut to be deleted Press the MOD key to tell MICROCUT you want to modify the job OPTION 2 CUT READY LIGHT ON IN AUTOMATIC MODE INSTRUCTION DISPLAY READS JOB 954 CUT 010 CHANGE CUT Y N Answer NO to the question JOB 954 CUT 010 LAY COMP The display will show JOB 954 CUT 010 Press the NO key INSERT CUT The display will show JOB 954 CUT 010 Press the YES key DELETE CUT The cut is deleted from the job memory Press the MOD key The display will show Press the NO key EJECT OR TURNAROUND The eject or turnaround is programmed in the same manner as a cut position but instead of pressing the ENTER key press the EJECT key Ejects do not count as a cut and you will see that the cut number does not advance in the display In automatic operation the backgauge will move to that location not wait for the cut but move directly to the next position instead STEP amp REPEAT This routine enters a number of equally spaced stops WHILE PROGRAMMING A JOB It can be used for labels or coupons The PROGRAM key must be lit see PROGRAMMING A NEW JOB INSTRUCTION D
4. To return to the original cut value BEFORE PRESSING ENTER press the LAST key to back up and then the ENTER key to come back to the original cut OPTION 2 CUT READY LIGHT ON IN AUTOMATIC MODE INSTRUCTION DISPLAY READS Press the MOD key The display will show JOB 954 CUT 010 Press the YES key CHANGE CUT Y N If this is a one time only change press the YES key The JOB 954 CUT 010 backgauge can be moved and the cut will change this lift only THIS LIFT ONLY Press the NO key for permanent changes Turn the handwheel or use the DRIVE keys to reposition the backgauge Do a KNIFE STROKE or press the ENTER key This will change the value of the cut at that particular location only Press the AUTOMATIC key if you decide you do not want to change the cut after all LAY COMPENSATE This is used to adjust all FORWARD MOVING stop values in the selected job number If it is done in the middle of a side of cuts it WILL NOT AFFECT cuts already made on that side This is a useful feature if trims gutters were not laid out accurately before printing adjustments can be made at the trim point and all labels will remain on size Itis also useful when compensating for gripper adjustments in cases where a four side trim out is not performed before cutting the printed sheet There is no limit to the number of times this feature can be used on a job Every trim gutter could be different and yet the STEP amp REPEAT programming method can
5. 5 8 bolts lock washers and flat washers see NOTE On some tables the sidegauge is quite thin Then it may be necessary to use extra flat washers thread a nut onto the bolt first or cut the bolt Make sure that the bolt does not protrude through the sidegauge Mount the base console to the mounting bracket with the hardware supplied Mount the console so that the cables will exit toward the bottom This will help when routing the sealtite later in the installation NOTE Some sidegauges are ribbed It may be necessary to use threaded rod with nuts to approximate studs to which the mounting bracket can be attached These rods are in the switch box section lower half of BOX 2 They will have to be cut to length after the mounting bracket is attached to the cutter and before the base console is installed THE LIMIT SWITCHES All parts are in the switch box 16 X 16 X 6 box contained within BOX 2 The limit switches have yoke lever arms and slotted angle mounting brackets The trip rod is in the pocket with the 3 8 16X12 threaded rod The 3 8 hardware bag for mounting the switches is in the center pocket of this box The base plate hardware bag for the trip rod is in the same pocket The extension plate is the 3 X 8 plate contained in its own pocket near the side of the box Move the backgauge to at least three inches in front of its rearmost position Mount the rear limit switch assembly both switches are identical and thus interchan
6. JOB This routine is used to program a series of stop points into MICROCUT so that it can operate in AUTOMATIC MODE To enter the PROGRAM MODE the MANUAL key must be lit press the MANUAL key INSTRUCTION DISPLAY READS 1 NEW 2 OLD LAST SAME JOB Press the PROGRAM key The key will light and the prompt will show Press the number 1 key to tell MICROCUT that you want to 1 AUTO JOB SEL program a new job The display will show 2 MANUAL SEL AUTO JOB SELECT means the computer will select the lowest numbered open job for you Press the number 1 key for this MANUAL SELECT means you will assign a job gt 00 If you press the 2 key the display will show RED NUMBER Pressing the NUMBER KEYS will roll the job number For JOB 954 ENTER example press 9 5 4 The ENTER key will let you continue DESIRED NUMBER The FORWARD REVERSE and MOVE keys can be used to position the backgauge Stop positions can be entered into JOB 954 CUT 001 memory with the KNIFE STROKE or with the NUMBER and CALCULATOR and ENTER keys CORRECTING OR REVIEWING CUT LOCATIONS LAST key backs up the CUT allows reprogramming if desired ENTER key Enters the cut value shown in the display CLEAR key clears the lower line of the display MOD key allows cuts to be added or deleted When you are finished programming the job press the AUTOMATIC key The computer will end the job and the backgauge will
7. MICROCUT is moving When the MOVE key light goes out you are in position Press the MANUAL key to stop the backgauge BEFORE it reaches position For entering fractions see CALCULATOR KEY OPERATION NOTE When entering a position you must roll out the number or the computer will give you an ERROR 8 inches 8 000 8 1 2 inches 8 500 To move a distance press the or key and enter the distance to move Then press the MOVE key O 5 CALCULATOR KEYS The calculator keys are used just like a normal calculator the numbers will appear on the right hand side of the prompting display after the or key is hit The key can be used for fractions You don t have to know decimal equivalents to program this unit The computer will figure it out for you The ENTER or key will total the display Fraction calculation example INSTRUCTION DISPLAY READS MICROCUT Key 2 5 0 0 0 25 000 MICROCUT Press the 4 key 25 0004 MICROCUT Press the 9 key 25 000 9 MICROCUT Press the key 25 000 9 MICROCUT Key in 1 6 25 0004 9 16 MICROCUT Press the ENTER key 25 562 Calculator keys can be used in all methods of operation Calculations can also be chained together 6 INCH OR CENTIMETER OPERATION Cuts can be entered in INCHES or CENTIMETERS or a combination of both Simply press the IN key for inches or CM key for centimeters The APPROPRIATE KEY WILL LIGHT telling you what units you are in O 7 PROGRAMMING A
8. THE MICROCUT SENSING SWITCH If part of the knife linkage is used check for impact on the switch during knife cycling which could cause fatigue If the linkage is adjustable for varied knife lengths verify that the switch will function for all adjustments Make sure that the switch does not return to its normal knife up position until the knife is well past bottom dead center see below Make sure that the switch will not be stressed or broken if the knife is cycled in the reverse direction as could happen during a knife change A spring lever arm is PUN as well as a roller arm to increase the mounting possibilities IF THE SPRING LEVER ARM IS USED MAKE SURE THAT IT IS NOT STRESSED TO THE POINT THAT IT WILL SNAP BACK AND RE TRIP THE SWITCH WHEN IT IS FINALLY RELEASED THIS WOULD CAUSE INTERMITTENT DOUBLE MARKING OF CUTS DURING PROGRAMMING NOTE The cut switch may be mounted anywhere on the cutter It is only important that the mounting allows the switch to cycle from OFF see below to ON and back to OFF during the knife cycle Ideally the cycle back to OFF will not occur before the knife is committed to its upstroke on some cutters the clamp and knife are controlled by the same valve and release of the knife buttons releases the clamp to the top while the knife stays down if the cut sense switch completes its cycle on the downstroke and the knife buttons are released before the upstroke MICROCUT could push the stock into the back of th
9. a preferred measurement to use MICROCUT will move forward to the front of the table and stop MOVING FORWARD Please wait PLEASE WAIT This is the same as when the rear value was entered The ENTER FRONT backgauge must be at an exact value less than 10 inches Use the REFERENCE VALUE NUMBER and ENTER keys to enter the reference position value Use the NUMBER and ENTER keys to tell MICROCUT how FPC WIDTH IS far forward the backgauge can move if the false paper clamp sole 0 000 INCHES plate is attached to the bottom of the clamp SEE NOTE AT BOTTOM OF PAGE Use the NUMBER and ENTER keys to tell MICROCUT MINIMUM FRONT IS how far forward the backgauge can move if the false paper clamp 0 000 INCHES is off SEE NOTE AT BOTTOM OF PAGE Use the NUMBER and ENTER keystotell MICROCUT how MAXIMUM REAR IS far back the backgauge can be driven before the mechanical 0 000 INCHES stop Answer the question FA If there is no false clamp press either the YES or the NO key CLAMP ON Press YES to show the thousandths in the display Press NO to YES SHOW 001 S show just the the hundredths NO SHOW JUST 01 NOTE Even though the display may not show the 001 s MICROCUT will still position to the 001 s in accuracy YES will show the the true position of the backgauge at all times SHOW TRUE SIZE IF If the NO key is pressed then MICROCUT will show the CUT READY ON programmed value as current position as lo
10. and is required if a clean 110 VAC line is not available if the installation uses a 1 H P motor A transformer DOES NOT imply that the power source is dedicated Other devices on the same line such as welders air compressors drills or fluorescent lights can require current surges that will deplete the transformer and thus affect MICROCUT Graphics West Micro Systems does not encourage the use of transformers for supplying power to MICROCUT If nothing but dirty power is available we suggest the use of an active tracking filter Contact us by means of phone telex or FAX numbers are on the cover of this manual for any questions you may have F DO NOT mount a separate 110 VAC power switch is not supplied with MICROCUT because one is not needed There is a power switch on the back of the display console This switch insures that the power supplies will come up in order so that none of the job or cutter pane memory is lost If power is lost during a storm the switch should be turned off until power is returned to the building 110 VAC power to the unit should be turned off before installing the display The switch on the display console should be turned off before the 110 VAC power 1s connected 1 5 G The boxes are packed in an order For instance all the brackets and hardware for the shaft encoder are supplied in the encoder box inside of box 2 If these parts are not randomly mixed with all of the other parts their use will
11. be more obvious and installation can progress much more smoothly There will usually be extra brackets left over We supply a bracket set that can be used for any combination of mountings Save any extra brackets for future needs slots in the brackets are designed for use with the supplied hardware 3 8 and 1 4 Do not use undersized bolts I base console mounts easiest if the display and shaft encoder cables exit at the bottom of the console J The display console should be mounted on a solid part of the cutter Hollow covers tend to transmit a lot of vibration through the display and to the computer Use at least two tie straps to mount the display cable to the display yoke This will act as a strain relief and prevent subsequent connection problems where the cable enters the display console L The shaft encoder drive sprocket on the leadscrew should be inspected to make sure that the faces line up and that the gap on either side caused by the width of the saw blade used to cut it in half is the same These sprockets are cut and stocked in matched halves As long as the alignment is proper there should not be a problem with chain wear Usually the clamp can be installed on the leadscrew before the sprocket halves are slid into position This makes the installation much easier M 24 tooth sprocket should be used on the shaft encoder if the leadscrew puc is less than or equal to this is a rough value 1 2 p
12. inputs The display console keys have been thoughtfully labeled Read them AND the prompting display the operating methods and options of MICROCUT will then be very simple This manual is designed to allow an operator to train himself Where the prompting display is used the manual gives the prompt message boxed in on the right side of the page Please refer to the TABLE OF CONTENTS for any of the operations you may require MICROCUT IS DESIGNED TO BE USED IN MANY DIFFERENT WAYS THIS MANUAL GIVES THE BASICS OF OPERATION NOT EVERY OPTION PLAY WITH MICROCUT TO SEE WHAT IT CAN REALLY DO FOR YOU 0 2 TURNING POWER ON TO MICROCUT MAKE SURE THAT ALL GUARDS AND SAFETIES ARE IN PLACE BEFORE TURNING ON POWER INSPECT THE MACHINE FOR ANY MOVING PARTS OR HAZARDS THAT ARE NOT FULLY GUARDED CORRECT ANY SAFETY PROBLEMS BEFORE CONTINUING MAKE SURE THERE ARE NO OBSTRUCTIONS TO NORMAL OPERATION MAKE SURE EVERYONE IS CLEAR OF DANGER START UP PROCEDURE INSTRUCTION DISPLAY READS Locate the ON OFF switch on the rear of the DISPLAY CONSOLE Press it and wait for the prompt PRESS AUTOMATIC Press the AUTOMATIC key The backgauge will move to the TO START rear of the table slowly to calibrate itself IN CASE OF EMERGENCY you can PRESS ANY KEY TO STOP THE MOVEMENT OF THE BACKGAUGE To resume the operation turn power off and start again from the top of this page TURN POWER OFF YOU WOULD NOT NORMALLY PRESS A KEY HERE RESTART UNLESS THE BA
13. of the older less used jobs before continuing NO MORE JOB S All of MICROCUT s 255 auto select jobs have been used It will be necessary to manually select a job number or erase one of the numbered jobs between and 255 NO MOTION SEEN MICROCUT has not detected any motion during a period of time when the backgauge should have been moving This may be due to either a drive or a counting error If the backgauge moves a bit and then stops MICROCUT is not seeing the motion and has a counting problem If no motion occurs then MICROCUT is suffering from a drive error Refer to this manual BASIC TROUBLESHOOTING and THE SHAFT ENCODER NOT ENOUGH MEMORY MICROCUT does not have enough unused job memory available to program the number of stops requested in either the STEP amp REPEAT or DIVIDE SHEET routine NUMBER TOO BIG The sum of numbers when using the calculator keys is larger than the maximum allowed value maximum rear value usually twice the maximum rear value in SHEET DIVIDE ROUTINE NUMBER TOO SMALL The result of a subtraction is less than zero or the position to MOVE to is less than the physical table limit see TOO FAR FORWARD S 14 OIL LEADSCREW OR REDUCE SPEED The backgauge drive circuitry has been run hard enough to heat past 80 of its rated capability MICROCUT will not allow additional drive until the components cool down adequately Perform maintenance on the cutter to avoid this problem again or slow down the drive speed see th
14. sensing switch should be mounted across the throat of the side loading table The closed contacts of this device should then be wired in series with the CLAMP SENSING switch terminals 9 and 10 of e ti block so that if either sensor prevents current flow the backgauge drive will be inhibited Everything safely pose has been done to make the installation of MICROCUT easy With proper it has been shown that installations can be simple and call backs for repairs and make rights ew HINTS MICROCUT will work best with a motor pulley ratio which allows about one inch of backgauge travel for every three to four revolutions of the motor While MICROCUT will automatically Set adapt to different ratios settling time will be minimized if this ratio is used Try to choose pulleys accordingly A thin belt will in general allow for faster settling than a thicker belt A groove versus B groove A cogged type V belt rather than solid performs best Leave the original equipment motor drive intact if possible This will ease the installation of the new limit switches since the backgauge will have to be moved to either table extreme To save trouble in wiring MICROCUT is supplied with connectors on the display and shaft encoder cables Each cable is about 12 feet long Mount the base console and components so that the cables will reach The base console is a junction box for all of the components and should be mounted in a central location on the
15. still be used to assure equal sized labels CUT READY LIGHT ON IN AUTOMATIC MODE INSTRUCTION DISPLAY READS JOB 954 CUT 010 Press the MOD key The display will show Press the NO key CHANGE CUT Y N Answer YES to the question JOB 954 CUT 010 LAY COMP If this is a one lift only change press the YES key The backgauge can be moved and the lay will change this lift only JOB 954 CUT 010 Press the NO key for permanent changes THIS LIFT ONLY Turn the handwheel or use the DRIVE keys to reposition the backgauge Do a KNIFE STROKE or press the ENTER key This will change the value of all the forward moving cuts Press the AUTOMATIC key if you decide you do not want to change the lay after all JOB DELETE This routine is used to remove a no longer wanted job from memory INSTRUCTION DISPLAY READS JOB 954 CUT 010 Find the job you want to delete see JOB REVIEW 40 000 Press the PROGRAM key The display will show JOB 954 CUT 010 Press the YES key DELETE JOB Y N Your job is erased MODIFICATIONS This routine is used for a number of different options which are standard in MICROCUT spacer systems This routine must be entered from the MANUAL MODE Press the MANUAL key if it is not already lit Press and HOLD the PROGRAM key While holding this key press the MOD key MICROCUT will enter the MODIFICATION ROUTINE INSTRUCTION DISPLAY READS Answer the question The false clamp is a metal pl
16. switch A mechanical switch cannot accurately sense a potential jam up and should not be used for such a purpose 1 16 SEALTITE Run sealtite from the base console to the following components see NOTE below Rear limit switch Front limit switch Motor Clamp up switch Cut sensing switch Paddle switch side loading only Use a separate piece of sealtite for each component Do not double up on components Wait until after the wires are strung next section before tieing the sealtite up with the straps supplied CLAMP UP SWITCH VAC IN CUT SENSE SWITCH ICROCUT BASE PADDLE SWITCH KNOCKOUT REQUIRED CONSOLE MOTOR FRONT LIMIT SWITCH REAR LIMIT SWITCH NOTE RUN THE SEALTITE TO THE BASE CONSOLE OPENING NEAREST EACH COMPONENT S TERMINAL CONNECTION THIS WILL KEEP THE INTERNAL WIRING MUCH NEATER Use a small amount of silicone spray spray oil or water inside the end of the sealtite before stuffing the wire through This will prevent the wire from snagging in the tubing It is advisable to cut all of the sealtite first The simplest way to snake the wire is to pull a sealtite length of wire off of the spool add a couple of feet to the length and then double it over Snake the doubled over end into the sealtite until it exits the far end Then cut the wire a few feet longer than needed 1 17 CABLES Attach the cables supplied to the shaft encoder and display console Sn
17. the wire from snagging in the tubing It is advisable to cut all of the sealtite first The simplest way to snake the wire is to pull a sealtite length of wire off of the spool add a couple of feet to the length and then double it over Snake the over end into the sealtite until it exits the far end Then cut the wire a few feet longer than needed Remember you are mounting Base console Front and rear limit switches with trip rod Clamp up switch Cut sensing switch Motor Shaft encoder Display console Paddle switch for side loading systems only ONDA R WN Complete the mechanical portion of the installation Then wire the switches and the motor This will save time and help to prevent errors THE BASE CONSOLE The base console is the black oil tight dust proof enclosure that is 12 X 14 X 4 in size packed in the bottom of BOX 1 The OMS Ue is the rectangular gold alodined assembly with slotted sides found at the top of BOX 1 The hardware bag is in the center section of BOX 1 Use the mount assembly to mark for four 3 8 16 threaded holes at a central location on the cutter side gauge or rear of housing This console acts as a junction box for all components which will be mounted Try to place it where it can be gotten to easily for wiring and service Care should be taken to avoid mounting the console in the way of access doors grease fittings etc on the cutter Bolt the mount assembly to the cutter with 3 8 16 X
18. 3 5 VDC RED 4 ZERO INDEX GREEN 5 SIGNAL A YELLOW BLUE OR WHITE CLEAR 6 SIGNAL B WHITE CLEAR OR YELLOW BLUE 1 19 110 VAC IN The power for MICROCUT should be from a 30 AMP DEDICATED breaker The cleaner the power the better Transformers do not insure good power Other devices on the same line as the transformer can cause problems Transformers tend to let the spikes commonly found on dirty power lines through to do damage to the computer Transformers also act as large inductors so that when the motor starts or stops the computer sees large voltage swings If a transformer must be used it should be well oversized 5 KVA or larger preferred Graphics West Micro Systems does not encourage the use of transformers for supplying power to MICROCUT If nothing but dirty power is available we suggest the use of an active tracking filter Contact us by means of phone telex or FAX numbers are on the cover of this manual for any questions you may have AN UNCLEAN POWER LINE WILL SEND SPIKES INTO THE COMPUTER AND ITS SURROUNDING CIRCUITRY WHILE MICROCUT IS DESIGNED AS BEST AS POSSIBLE TO OVERCOME THESE SPIKES IN TIME THE SPIKES WILL BEAT THE CIRCUITRY TO DEATH AND FAILURE WILL OCCUR THE CLEANER THE POWER THE LONGER MICROCUT WILL WORK RELIABLY START FROM THE BEGINNING WITH A GOOD CLEAN POWER LINE DO NOT WAIT FOR PROBLEMS TO OCCUR 1 20 THE FINAL SETUP 1 Use the tie straps and mounting straps with 10 32X1 2 allen
19. 5 was on the contactor is pulled in Therefore it will be necessary to clean the contact points or replace it entirely This contactor is in the upper left corner of the power board 9 Measures the power from the on board 5 VDC supply mounted to the backside of the heatsink Failure could be due to a short in the shaft encoder although this would be very rare Replacement of the device or the full base console is recommended 10 Measures power back from the rear limit switch Check the switch for proper position backgauge forward of switch TURN POWER OFF AT THE WALL BREAKER and check for loose wires 11 12 13 14 15 16 17 18 19 20 21 22 23 24 5 9 Measures power back from the front limit switch Check the switch for proper position backgauge to the rear of the switch TURN POWER OFF AT THE WALL BREAKER and check for loose wires Measures power back from the clamp up switch Check to make sure the switch is being mechanically tripped TURN THE POWER OFF AT THE WALL BREAKER and check for loose wires Measures torque enable signal from motor drive supplycontrol circuit Check to make sure the power ee for slow and high speed are NOT set to 0 See ADJUSTING MOTOR SPEEDS SECTION If failed replacement of the base console is recommended Measures motor drive supply enable signal Failure indicates a problem with U8 Replace this chip or the base console Measures the CPU speed comma
20. 9 THE FINAL SET UP I 20 THE FINAL CHECK OUT I 21 ADDITIONAL CONTROL LINES I 22 MICROCUT SPARE PARTS LIST I 23 PERSONAL NOTE SPACE I 24 I 1 INTRODUCTION MICROCUT is a self contained microprocessor controlled positioning system MICROCUT must have a place to attach the drive motor to an existing or anew pulley and shaft encoder for position sensing The motor should turn at least three to four turns per inch of backgauge travel The shaft encoder sprocket should turn between 2 and 4 times per inch of backgauge travel MICROCUT IS NOT INTENDED TO CONTROL THE KNIFE OR THE CLAMP ON THE PAPER CUTTER MILL TRIMMER ANYTHING DEALING WITH THE CLAMP AND KNIFE IS NOT TO BE TAMPERED WITH OR ADJUSTED TO INSTALL OR OPERATE MICROCUT ANY ALTERATIONS TO THE KNIFE OR CLAMP SAFETIES CIRCUITS AND OPERATION OR ANY INSTALLATION TECHNIQUE WHICH COMPROMISES THE SAFETY OF ANYONE WORKING ON OR AROUND THE PAPER CUTTER MILL TRIMMER WILL VOID ANY AND ALL WARRANTIES ON MICROCUT THIS POLICY ALSO APPLIES TO CASES WHERE MICROCUT IS INSTALLED ON DIFFERENT TYPES OF EQUIPMENT OR MACHINERY MICROCUT CONSISTS OF PARTS AND ASSEMBLIES WHICH ARE ADDED TO THE MACHINE GUARDING MAY NEED TO BE ALTERED OR ADDED TO OFFER PROPER PROTECTION THIS MUST BE DONE BEFORE MICROCUT IS OPERATED DO NOT OPERATE THE MACHINE UNTIL THIS GUARDING IS COMPLETE ALL MOVING PARTS AND HAZARDS MUST BE COVERED IN SUCH A WAY AS TO PREVENT ACCIDENTAL CONTACT OF ANY SORT This INSTA
21. CKGAUGE HAD TO BE STOPPED After the backgauge reaches the rear of the machine the RED readout will read the correct position MICROCUT is calibrated and ready to use The MANUAL key will light PRESS ANY KEY TO STOP If there are any problems during start up the prompt will give you an error message Please consult the SERVICE MANUAL for assistance O 3 MANUAL DRIVE OPERATION Pressing the key marked FORWARD will drive the backgauge toward the knife slowly at first then fast The RED display will give the true position of the backgauge Pressing the key marked REVERSE will do the same thing except the backgauge will move in reverse To obtain SLOW SPEED ONLY toggle the proper key for either direction The backgauge will automatically slow as it approaches either table extreme NOTE THE BACKGAUGE SHOULD ALWAYS BE POSITIONED MOVING IN THE FORWARD DIRECTION TO PREVENT BACKLASH AND INACCURATE CUTTING 0 4 SEMI AUTOMATIC OPERATION This routine is used to move the backgauge to a position in either MANUAL or PROGRAM modes of operation The light must be lit on either the MANUAL or the PROGRAM key INSTRUCTION DISPLAY READS The UPPER line of the CLEAR PROMPT DISPLAY may contain MICROCUT one of 2 possible readouts OR JOB CUT Enter a position using the NUMBER keys Example 8 inches MICROCUT press the 8 key and then press the 0 zero key three times 8 000 Press the MOVE key It will light showing that
22. GUAGE WITHOUT THE PRIOR WRITTEN CONSENT OF GRAPHICS WEST MICRO SYSTEMS SABER MICROCUT AND MICROFACTS ARE REGISTERED TRADE MARKS OF GRAPHICS WEST MICRO SYSTEMS GMS GRAPHIC MACHINERY amp SYSTEMS A DIVISION OF GOLDEN GATE MICROSYSTEMS INC 30 Golden Gate Drive San Rafael CA 94901 Tel 415 457 7500 Fax 415 457 1964 e mail sales graphicmachinery com _ http www graphicmachinery com OPERATOR S TABLE OF CONTENTS MICROCUT DESCRIPTION O 1 TURNING POWER ON START UP O 2 MANUAL DRIVE OPERATION O 3 SEMI AUTOMATIC OPERATION O 4 CALCULATOR KEYS O 5 INCH OR CENTIMETER OPERATION 6 PROGRAMMING JOB O 7 INSERT CUT O 8 DELETE CUT O 9 EJECT OR TURNAROUND O 10 STEP amp REPEAT O 11 SHEET DIVIDE O 12 JOB REVIEW O 13 AUTOMATIC OPERATION O 14 CHANGE CUT O 15 LAY COMPENSATE O 16 JOB DELETE O 17 MODIFICATIONS O 18 SETTING UP MICROCUT O 20 ADDENDUM TO SETTING UP MICROCUT 23 IN MM CM COMPARISON TABLE O 26 USE OF ORIGINAL EQUIPMENT CONTROLS 0 27 O 1 MICROCUT DESCRIPTION MICROCUT is a solid state electronic motor drive control system that contains 999 programmable jobs and 500 storage locations In the AUTOMATIC MODE of operation MICROCUT will position the backgauge sequentially according to the stop points that have been programmed on the selected job At the end of the sequence it will then return to the beginning again The DISPLAY CONSOLE mounts on the front of the cutter and is used for display readouts and all operator
23. ISPLAY READS Press the PROGRAM key The display will show JOB 954 CUT 001 Press the YES key STEP amp REPEAT Y N If NO is answered here MICROCUT will skip the next promp and calculate the first stop value automatically If you know the JOB 954 CUT 001 FIRST CUT KNOWN first cut value answer YES Use the NUMBER keys with ENTER or the KNIFE STROKE JOB 954 CUT 001 to enter the first cut FIRST CUT AT Use the NUMBER keys with ENTER to tell MICROCUT the JOB 954 CUT 4001 number of labels or coupons NUMBER UP Use the NUMBER keys with ENTER to tell MICROCUT the OB 954 CUT 001 label or coupon size LABEL SIZE If NO is answered the next prompt will be skipped and MICROCUT will program only for the label coupon size If JOB 954 CUT 001 thereisa trim gutter press the YES key TRIM YES OR NO Use the NUMBER keys with ENTER to tell MICROCUT the JOB 954 CUT 001 trim gutter value ENTER TRIM VALUE If the first cut value was not known or if it was entered with the KNIFE STROKE this prompt will be skipped Answer YES to keep the first stop NO to omit it JOB 954 CUT 001 BACKTRIM SHEET NOTE The first stop should be kept if the sheet has not been trimmed to size before starting the STEP amp REPEAT sequence If the sheet has been through a four side trim to remove variances due to gripper adjustments then you will probably not want to backtrim answer NO The LOWER LINE of the prompt display
24. LLATION MANUAL is organized into NOTES HINTS MECHANICAL INSTALLATION ELECTRICAL HOOKUP FINAL SETUP FINAL CHECKOUT and ADDITIONAL CONTROL LINES Read it thoroughly before starting In general completion of the mechanical installation is recommended before any wiring is done THIS MANUAL IS DESIGNED TO GIVE A CONCEPTUAL APPROACH TOWARDS INSTALLING MICROCUT MICROCUT IS A RETROFIT SYSTEM FOR MANY DIFFERENT TYPES OF MACHINES ALL INSTALLATIONS WILL VARY USE THIS MANUAL TO LEARN WHAT EACH COMPONENT MUST DO THEN MOUNT THE COMPONENT SO THAT IT IS BEST SUITED TO FULFILL ITS PURPOSE I 2 THE INSTALLATION DRIVE BELT SWITCHES TO MICROCUT MOTOR MA MICROCUT Lj MOTOR MOUNT E 7 D S i L C REAR LIMIT 5 d SWITCH E 4 we BASE 3 CONSOLE BACKGAUGE 7 38 3 TRIP ROD o FRONT LIMIT SWITCH ox UE EM CLAMP UP SWITCH xe a Doe Fd E u DISPLAY ZSHAFT ENCODER CONSOLE 5 1 ERI uA mmm HANDWHEEL ON SOME PAPER CUTTERS IT IS NOT ALWAYS POSSIBLE TO FIND SPACE TO MOUNT A SECOND MOTOR IT MAY BE NECESSARY TO REMOVE THE ORIGINAL MOTOR AND INSTALL THE MICROCUT MOTOR IN THE OE SPACE NOTE Position of the parts is for visualization only Every installation will be unique Mount components for function and form not necessarily to mimic this diagram DO NOT USE GREASE ON THE LEADSCREW MECHANISM GREASE ATTRACTS ABRASIVE DIRT AND ACTS AS A
25. N INCONSISTENT CUSHION AGAINST THE BACKGAUGE PREVENTING PROPER CUTTING PRECISION USE A LIGHT MACHINE OIL ONLY ON THE LEADSCREW OIL THE LEADSCREW DAILY 1 3 RECOMMENDED TOOL LIST Every installer will want to modify this list This is only a guide The tools are listed in approximate order of use FOR DETERMINING ALL MICROCUT PART DRILLING LOCATIONS Slide n square Penci FOR PREPARING FOR DRILLING HOLES FOR MOUNTING ALL PARTS Hammer Center punch prick punch FOR DRILLING ALL HOLES FOR ALL PARTS AT ONE TIME Paper and rags to cover machine surfaces 36 21 7 1 4 21 64 3 8 high speed drill bits Electric hand drill Extension cord FOR TAPPING ALL HOLES FOR ALL PARTS AT ONE TIME 6 32 10 32 1 4 20 5 16 18 3 8 16 spiral taps Tap handles ratchet type are nice Tapping fluid FOR CLEANING ALL METAL FILINGS OFF OF THE MACHINE Brush Rags FOR BOLTING AND SECURING ALL MICROCUT PARTS TO THE MACHINE 7 16 1 2 9 16 wrenches and sockets Allen wrench set SAE FOR CUTTING THE SEALTITE TO SIZE FOR ALL OF THE WIRED PARTS Side cut pliers FOR WIRING THE PARTS Wire strippers Needle nose pliers Small common screw driver Large common screw driver FOR CUTTING THE LIMIT SWITCH TRIP ROD AND PREPARING THE GUARDING Hack saw Flat file DRILL 36 21 7 1 4 21 64 TAP SIZE 6 32 10 32 1 4 20 5 16 18 3 8 16 This drill according to the charts should actually be a 5 16 value but the extra 1 64 makes tappi
26. T is area in the AUTOMATIC MODE or there is no JOB in the prompting display There are other possibilities as well for instance if MICROCUT is waiting for a reply to a question 6 UNIT IS OFF CALIBRATION BY ONE SHAFT ENCODER REVOLUTION a Zero set timing is off Loosen the shaft encoder chain and rotate the shaft encoder ear 1 3 turn Retension and go through the SET UP ROUTINE to recalibrate ce OPERATOR S MANUAL 7 MICROCUT IS OUT OF CALIBRATION a Check the dimension units INCH or CM b Referto the OPERATOR S MANUAL MODIFICATIONS 8 MICROCUT DOES NOT COUNT ONE FOR ONE WITH THE TABLE a wrong units are selected Check the IN and CM keys b The reference values used in the SET UP ROUTINE see OPERATOR S MANUAL SET UP ROUTINE were not exact c The shaft encoder or the leadscrew sprocket is loose Check for tightness Mark the sprockets at a mechanical reference point and run the backgauge back and forth Check the markings at the same reference point for alignment d Failed shaft encoder replace 9 IMPROPER OR ERRATIC COUNTING BACKGAUGE POSITION a The shaft encoder cable has failed Check the cable for bad solder joints Replace if necessary b Thereisaconnection problem Check the wires going into the SHAFT ENCODER TERMINAL BLOCK in the base console c display cable is not making a good connection Check the connections or replace the cable NOTE Cable connections can fail
27. TE THE MACHINE UNTIL THIS GUARDING IS COMPLETE ALL MOVING PARTS AND HAZARDS MUST BE COVERED INSUCH A WAY AS TO PREVENT ACCIDENTAL CONTACT OF ANY SORT 3 Cut the limit trip rod to an appropriate length and file the a edges smooth 4 Make the notations in the OPERATOR S MANUAL USE B THE ORIGINAL EQUIPMENT CONTROLS 5 Check MICROCUT to make sure all of its functions and operat ions are performing properly positioning settling programming etc 6 Refer to ADJUSTING MOTOR SPEED in the SERVICE MANUAL for adjust ing the high speed and slow speed to the operator s preference 7 Train the operator s 1 22 ADDITIONAL CONTROL LINES MICROCUT has two additional control lines which can be used to control the switching of 12 VDC coiled relays not included The CONTACTS OF THESE RELAYS can then be used to control other functions of the machine Refer to the diagram in the WIRING THE SWITCHES AND MOTOR section of the manual for the location of these lines Control line 1 Relay switches on whenever fast forward is used This could be used as an air bed disable by switching the air solenoid through the normally closed contacts Control line 2 Relay switches on whenever the cut ready light is on This could be used as electromagnetic brake enable to lock the backgauge after position has been reached in automatic mode MICROCUT SPARE PARTS PRICE LIST PART Base console Display console 1 2 HP motor 1 HP motor Sha
28. ake the cables through the cutter so that they are out of harm s way and hopefully out of sight Be careful of moving parts clamp knife motors belts etc Tie any excess cable under the table with the tie straps supplied Use tie straps for strain relief on the display console cable by tieing the cable onto the cross bar between the yokes 1 18 WIRING THE SWITCHES AND MOTOR Use the 14 gauge wire for all switches and for the motor Connect wires two per component to the appropriate devices The LIMIT switches must conduct power ONLY when tripped towards the center of the table The CUT switch must NOT conduct current when the knife is up The CLAMP UP switch should conduct current ONLY when the clamp is in it s full up position The PADDLE switch should conduct current ONLY when the paddle is clear of the table for cases where the paddle switch was installed only do not jumper these terminals Motor polarity will be determined at the SET UP ROUTINE later in the installation Interlock FET BYPASS REV C ONLY Interlock 12 VDC REV C ONLY VAC AIRBED CONTROL VAC 12 VDC Ground BRAKE CONTROL Motor 12 VDC Motor CLAMP SWITCH OUT 12 VDC CLAMP SWITCH IN CUT SWITCH IN GROUND CUT SWITCH OUT PADDLE OUT 5 VDC PADDLE IN FRONT LIMIT IN FRONT LIMIT OUT 12 VDC REAR LIMIT IN REAR LIMIT OUT 12 VDC SYMBEX CABLE CONNECTOR TO DISPLAY CONSOLE 123 4 5 6 SHAFT ENCODER 1 SHIELD HEAVY BLACK 2 GROUND THINNER BLACK
29. ances AND the AUTOMATIC key is lit If the backgauge is knocked out of its settling tolerances see the MODIFICATIONS section of this manual the CUT READY LIGHT will go out If the CUT READY LIGHT flickers the tolerances may be set too tightly see the MODIFICATIONS section of this manual The LAST key will back MICROCUT up to the previous stop The MOVE key or the KNIFE STROKE will advance MICROCUT to the next stop The MOD key allows program changes CUT READY LIGHT on The MANUAL key exits AUTOMATIC MODE No other keys are operational in AUTOMATIC MODE To modify an EJECT press and hold the MOD key until the eject value is reached To exit AUTOMATIC MODE temporarily press the MANUAL key MANUAL and SEMI AUTOMATIC MODES can be used without affecting the JOB and CUT in the prompt display Press the AUTOMATIC key to enter AUTOMATIC MODE at the same place you exited CHANGE CUT This routine is used to change a stop value in the selected job number OPTION 1 PROGRAM KEY LIT IN PROGRAM OR REVIEW MODES INSTRUCTION DISPLAY READS Use the ENTER or LAST key to locate the cut to be changed Press the CLEAR key to blank the display Use the NUMBER and or CALCULATOR keys to display the new cut value Press the ENTER key when ready JOB 954 CUT 010 40 000 NOTE The CLEAR key is optional You can write over the existing cut with the NUMBER keys or add and subtract from it with the CALCULATOR keys IF CLEAR is not pressed
30. ate which attaches to the bottom of some clamps and limits the maximum forward travel FALSE PAPER CLAMP ON Y N 9 Answer the question CONTINUE MODS YES OR NO If you answer NO MICROCUT will return you to MANUAL MODE If you answer YES MICROCUT will continue with more questions and options Press YES to show the thousandths in the display Press NO YES SHOW 001 S to show just the the hundredths SHOW JUST 01 NOTE Even though the display may not show the 001 s MICROCUT will still position to the 001 s in accuracy YES will show the true position of the backgauge at all times If the NO key is pressed then MICROCUT will show the SHOW TRUE SIZE IF programmed value as current position as long as the CUT READY LIGHT is ON CUT READY ON NOTE If the backgauge is knocked beyond the settling tolerances see 2 steps further on THE TRUE POSITION WILL THEN BE SHOWN UNTIL THE SETTLING TOLERANCES ARE SATISFIED AGAIN O 19 Press the YES key if you want MICROCUT to reposition the SELF CORRECTING backgauge if it is knocked out of settling tolerance in IN AUTOMATIC AUTOMATIC MODE see directly below Enter 1 to 9 The larger the number the faster MICROCUT TOLERANCE IS settles Usually 2 or 3 15 recommended Poorly maintained 0 003 INCHES machines may require larger values NOTE If the tolerance is set too small the CUT READY LIGHT will have a tendency to flicker on and off when MICROCUT reaches the
31. before programming KNIFE DOWN MICROCUT will display this prompt after a knife stroke is performed in either the PROGRAM or AUTOMATIC MODES of operation The prompt will clear and operation will continue normally as soon as MICROCUT senses that the knife is no longer down S 13 LIMIT ERROR CHECK SWITCHES MICROCUT has sensed that BOTH the front and rear limit switches are tripped at the same time This should be an impossibility and needs to be checked out carefully MAKE ADJUSTMENTS TO CONTINUE The NO key has been pressed in response to one of MICROCUT s questions Adjustments will need to be made depending upon the question before a routine can be continued this prompt is used while checking switches in the SET UP ROUTINE MEMORY FAILURE TURN POWER OFF MICROCUT has sensed a failure in the job memory and will not let operation continue Turn the pow off It is advisable to enter the SET UP ROUTINE and test the memory If the error is fairly igh in the address range it may be possible to erase some of the lower jobs and continue on MICROCUT may skip over the bad location after power is turned off but memory errors may occur if jobs are altered in the future Schedule service on the memory chip as soon as possible MEMORY POSITIONS AVAILABLE MICROCUT is warning the operator that there are only so many memory positions left at the entrance to programming a new job If the job will require more than the shown number of cuts left delete some
32. drature type There are five lines attached at the shaft encoder DISPLAY CANNON TERMINAL CONNECTOR Black Ground GND 5 F Red 5 VDC 5V 4 D Green Zero Set Z 3 White or Clear Signal A 20 1 Yellow or Blue Signal B lor2 B NOTE Terminal 6 is the cable shield and connects only at the base console The shaft encoder is a disc type optical interrupter with 500 windows separated by lines The lines block light to a pair of phototransistors while the windows allow light through As the shaft encoder turns its signals look like this 7 Traveling Left to Right Right to Left A goes low B is high B is low A goes high B is low B is high B goes low A is low A is high B goes high A is high A is low A brief inspection shows us that the direction of count can be reversed by interchanging the A and B signal lines If these are wired backwards at the time of installation MICROCUT will tell the installer in the SET UP ROUTINE to invert the lines One of MICROCUT s computers analyzes all signal transitions and count direction is determined forward or back from the value high or low of the other signal line An up and a down transition occur in both A and B per shaft encoder window yielding four counts per window The 500 windows per revolution allow information to one two thousandth of a revolution At every zero set the count is checked and corrected to 2000 or 0 counts from the last zer
33. due to contamination Keep the cable ends away from dirt and oil etc when they are not connected Sometimes a connection problem here can be cured just by removing the connector and putting it back on The sliding action of the pins can help self clean them It is a good idea to insert and remove the cables a few times at the time of installation Refer to the section titled MAINTENANCE in this manual 5 5 10 TENDS SUFFER COUNT FAILURES a backgauge speed is set too high Note that this maximum speed depends upon the shaft encoder gearing If the shaft encoder turns twice per inch the maximum speed is 16 second If the shaft encoder turns four times per inch the maximum speed is 8 second Adjust as necessary b MICROCUT has an inadequate 110 VAC supply A poor 110 VAC line forces MICROCUT to compensate more and more in it s count protection software and slows down the maximum counting speed which it can handle before defaults occur Connection problem See previous paragraph 9 The shaft encoder is failing This can cause adegradation of the A and B signals see the SHAFT ENCODER section of this manual which can cause subsequent count detection errors Replace the shaft encoder 11 OPERATING MODE KEY S DO NOT LIGHT UP a mode has not been selected try again b There is a burned out bulb replace as necessary 12 THERE IS GARBAGE IN THE MEMORY a The memory was n
34. e OPERATOR S MANUAL or SERVICE MANUAL See the prompt DRIVE OVERHEATED WAIT FOR COOLING OUT OF MEMORY All of the available job memory has been used Note that while MICROCUT has the option for 999 different job numbers each job may take up several of the available memory locations The memory space will be used up before all 999 jobs are programmed Delete some of the unused or seldom used jobs to make room for the new ones OUT OF POSITION MICROCUT is not in position for the knife stroke but it senses that the knife is being operated Bring the knife back up to the top of its stroke and allow MICROCUT to position the backgauge correctly See the prompt CUT STROKE EARLY OUT OF TOLERANCE The duplicated memory in MICROCUT does not match Go through the SET UP ROUTINE OPERATOR S MANUAL to correct this If the comes up again there may be a failed memory chip in MICROCUT Test the memory in the SET UP ROUTINE to see if this is the case PRESS ANY KEY TO STOP This prompt appears only when MICROCUT is starting up and it is possible that someone or something is around the machine in such a way as to be endangered by the movement of MICROCUT ANY KEY WILL STOP MICROCUT FROM MOVING THE BACKGAUGE REAR LIMIT ERROR MICROCUT has sensed that the rear limit has been tripped for much too long a distance moving forward NOTE This error will occur during calibration when power is first turned on if MICROCUT has to move forward mor
35. e base console which help simplify troubleshooting Refer to the DRIVE TROUBLESHOOTING section for any related problems Problems in the computer can be subdivided into the following sections A Operational B Counting C Memory D Miscellaneous In general complications in the computer should be approached by turning the power off and back on to see if things straighten out Deea If this occurs frequently more than once a year excluding thunder storms MICROCUT should have its AC power supply checked This should be a dedicated line with a 30 Amp breaker A separate ground should be run as well see INSTALLATION MANUAL 110 VAC IN Connections on the display cable or electrical problems within the machine itself could also be at fault Refer to the TABLE OF CONTENTS for the appropriate page number in this manual for any problems you may have 5 2 BASIC TROUBLESHOOTING The MICROCUT display console houses two printed circuit boards the CPU board and the display board There are two computers in the display console One is for counting the DUE sent from the shaft encoder to keep track of backgauge position The other handles the housekeeping work keyboard display memory math drive etc Both computers reside on the CPU board along with the 5 volt supply and the job memory see NOTE The display board consists of keys displays current position and prompting various control IC s and the warning buzzer In general these
36. e SET UP ROUTINE section in the OPERATOR S MANUAL When troubleshooting is complete turn power off to exit the SET UP ROUTINE All of the first 24 diagnostic lights should be lit Approach them in order The first unlit light will diagnose the problem directly If all are lit and drive is still not operating refer to Diagnostic 25 and 26 motor ON OFF command LIST OF DIAGNOSTIC LIGHT FUNCTIONS BY REFERENCE NUMBER 1 Measures AC power into MICROCUT If unlit check the wall circuit breaker responsible for delivering power to MICROCUT 2 Measures AC power through the door interlock Check to make sure the interlock switch is defeated see above 3 Measures the AC power through the 12 VDC power supply fuse If unlit replace the fuse with a 3 amp equivalent 4 Measures the 12 VDC supply If unlit this represents failure in the transformer or full wave bridge on the PC board Replacement of the base console is recommended 9 Measures AC power through ON OFF relay contactor Visually the uppermost relay to make sure it is pulled in If not check the connections to the display console If so replace the contactor 6 Measures AC power through the motor drive fuse If unlit replace the fuse with a 30 amp equivalent 7 Measures power out of the motor drive full wave bridge attached to the heatsink If unlit replace the full wave bridge 8 Measures 12 VDC power through the ON OFF contactor Assuming diagnostic
37. e knife trying to advance to the next stop OFF means the switch does not conduct current ON means the switch conducts current The switch has both normally open and normally closed contacts to increase mounting possibilities 1 12 THE MOTOR MOUNTING The motor is shipped in its own box The pulley for the motor is in the MISCELLANEOUS BOX 10 X 16 X 6 contained in BOX 2 Two pulleys are included one which is adjustable and one smaller one which is not The motor mounting plate is in the top of the switch box 16 X 16 X 6 contained in BOX 2 The 3 8 hardware bag and threaded rod in this same box can be used to mount the plate to the cutter The 5 16 hardware bag contains the bolts and washers to secure the motor to the mounting plate Some cutters have original equipment electromagnetic backgauge brakes which will require either the removal of a fuse or wire to defeat them Others may require the addition of a switch to lock on a backgauge drive clutch On some cutters it will be necessary to mount a new pulley on the leadscrew for the MICROCUT motor Senators with gearbox drive some Michael Miracles On others it will be necessary to mount the motor to the leadscrew through an existing gearbox Pacemaker II spacers see NOTE below In general it is best to mount the MICROCUT motor so that it lines up with the existing leadscrew drive pulley In many cases the same belt can be used for the new motor as was used for the origina
38. e than a few inches to get off of the rear limit switch In some cases the rear limit may trip several inches before the rear of the table although this is not the preferred manner of installation If this is the case then turn the power off and restart normally If this sense were not in MICROCUT and an error bad connection occurred from the rear limit switch MICROCUT could run the backgauge into the front of the cutter This check prevents that from happening if such a failure occurs REAR LIMIT HAS A WIRING PROBLEM MICROCUT senses that the rear limit switch is tripped when it is not supposed to be Check the wires for proper connection see the INSTALLATION MANUAL SLOW DRIVE PROB MICROCUT has not detected any motion during a period of time when the backgauge should have been moving This may be due to either a drive or a counting error If the backgauge moves a bit and then stops MICROCUT is not seeing the motion and has a counting problem If no motion occurs then MICROCUT is suffering from a drive error Refer to this manual BASIC TROUBLESHOOTING and THE SHAFT ENCODER S 15 TARGET LOST At least one of MICROCUT s internal data backup registers does not agree with the others in regards to the position which MICROCUT is supposed to drive to MICROCUT performs its operations in several areas at the same time in order to compare results if electrical disturbances occur which prevent the results from being equal MICROCUT halts op
39. echeck drive capability Leave any FETs that disable drive out Schedule service for final repairs If two FETs are removed and there is still no drive replace one of the removed FETs and unsolder the last one Then check for drive BOARD REV E the same procedure as REV C but remove each of the fuses 1 2 3 instead of unsoldering the FETs REFER TO THE NEXT PARAGRAPH The motor brushes are bad Examine them for wear Carefully clean the motor to remove all built up carbon dust 4 FET s CONTINUE FAIL a The motor pulley ratio is wrong The motor pulley ratio should be about 4 motor turns per 1 of backgauge drive If the ratio is less the backgauge resistance will drag the motor speed down This will cause the system to use excessive current especially during starts REFER TO THE NOTES SECTION OF THE INSTALLATION MANUAL FOR FURTHER CLARIFICATION The 110 VAC line is inadequate Check 110 VAC line carefully Refer to the INSTALLATION MANUAL 110 VAC IN There is a bad connection to the display console Check The cable Replace if necessary 5 4 5 KEY S FAILS TO RESPOND Refer to the prompting display and key lights to make sure the key failure is not due to the operational approach For instance a No keys respond prompt reads PRESS AUTOMATIC TO START or MICROCUT is in the AUTOMATIC MODE b The MOVE key does not respond there is no number in the prompt to move to c The AUTOMATIC key does not respond MICROCU
40. emain low for a VERY BRIEF arc of the shaft encoder revolution thereafter See SHAFT ENCODER in this manual 5 11 PROMPT ERROR MESSAGE LIST MICROCUT has several prompts to tell the operator of existing or paon error conditions The following list is a synopsis of these codes Refer to other sections of the SERVICE MANUAL for additional information CANNOT BE ZERO The fraction when using the calculator keys cannot have zero in the denominator CHECK DIAGNOSTICS MICROCUT has sensed an error which may be easier to evaluate by inspecting the DIAGNOSTIC lights in the base console Turn the power off to MICROCUT Open the base console door and pull out on the door interlock units before 1987 only Turn the power back on and enter the SET UP ROUTINE see the OPERATOR S MANUAL Also refer to the prompt DIAGNOSTICS OK CLAMP DOWN The clamp sensing switch is not pe properly This may be due to a mechanical problem with the clamp or the switch or there may be a connection problem between the switch and MICROCUT CLAMP SWITCH HAS A WIRING PROBLEM MICROCUT senses that the clamp is down when it is SUPPOSE to be up Check the wires for continuity through the switch see the INSTALLATION MANUAL COUNTING SYSTEM ERROR RESTART MICROCUT s intelligent counting system has detected an out of range error condition and can not correct itself back to within limits The backgauge drive is disabled and the buzzer will go on and off Refer to other sections i
41. er turn For courser leadscrews a 12 tooth sprocket should be supplied Verify that the sprocket is proper at the start of the installation Also check the leadscrew sprocket for proper bore size The shaft encoder should make between 2 and 4 revolutions per inch of backgauge movement N Thereis no provision for checking zero set timing on the shaft encoder Generally this is not a problem but in machines with a large shaft encoder turns ratio it is possible that MICROCUT may calibrate one shaft encoder revolution off After installation have MICROCUT calibrate several times If it does have a timing problem calibrates off loosen the shaft encoder swing bracket and remove the chain Turn the shaft encoder sprocket a quarter turn clockwise and re tension the Go through SET UP ROUTINE OPERATOR S MANUAL Repeat the checking procedure A spring lever arm is supplied as a convenience for mounting the CUT SENSING SWITCH in certain applications DO NOT use this for the CLAMP SENSING SWITCH It will allow too much play and will not suffice when the operator is running a full lift of stock P switch heads on the CUT and CLAMP switches can be mounted in any of four different ways by removing the four fastening screws Likewise the roller lever arm can be mounted facing away from or towards the center of the switch The locking washer for this arm can be used to allow only straight or any angled position of the arm The s
42. eration with this error prompt This safety gives assurance that MICROCUT will not make errors in positioning If this message occurs often check the MICROCUT power supply line very carefully Refer to the INSTALLATION MANUAL NOTES HINTS 110 VAC or POWER SUPPLY THE SIDE LOADING THROAT IS JAMMED The side loading throat is jammed MICROCUT will not allow drive until the obstruction is cleared TOO FAR BACK The position that was requested is beyond the physical limits of the table MICROCUT limits the prompt display to realistic values as the number keys are pressed if the resulting number is larger than the max mum rear it blanks the leading digit However in the SHEET DIVIDE routine MICROCUT allows values to twice the maximum rear in the event that a pre sized sheet is to be cut in two with no backtrim If the first cut value calculated in SHEET DIVIDE is larger than the maximum rear value this prompt will show If acutis made in the PROGRAM mode that is behind the maximum rear value entered in the SET UP ROUTINE this error will appear TOO FAR FORWARD The position that was requested is beyond the p limits of the table If the position is between the minimum front and the false paper clamp false clamp ON in the MODIFICATION ROUTINE OWNER S MANUAL MICROCUT will continue with the prompt FALSE CLAMP ON and wait for a YES or a NO response TURN POWER OFF RESTART Microcut has been told to stop or it has completed a routine which req
43. ft encoder bare Shaft encoder assembl Limit switch snap Tock ype Clamp cut sensing switc Spring lever arm for cut switch Display cable Shaft encoder cable Motor brushes pair Key diffuser with lens engraved Key light Nylatron chain 1 foot piece Unbored 24 tooth sprocket Bored 24 tooth sprocket 3 8 bore 12 tooth sprocket Manual Display console repair Base console repair Base console spares kit component breakdown prices are extended according to quantity 2 relays 4 FET transistors 2 LM339 quad comparators 2 DS3632 dual relay drivers 2 4081 quad AND gates 2 555 timers 2 7404 hex inverter 2 4029 presettable counter 2 LM324 uad op amp 5 30 amp fuses 5 5 amp fuses 5 3 amp fuses SUBTOTAL Full kit price Base console parts are available individually as well PRICE 2500 00 3000 00 275 00 460 00 350 00 425 00 75 00 30 00 12 00 75 00 50 00 25 00 7 00 2 00 10 00 12 00 35 00 25 00 25 00 250 00 250 00 45 00 72 00 6 00 18 00 4 50 4 50 4 50 3 00 3 00 3 00 178 50 150 00 PRICES AVAILABILITY AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION 1 23 1 24 PERSONAL NOTE SPACE PERSONAL NOTE SPACE 1 25 microcut USER S MANUAL Revision 498 THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION WHICH IS PROTECTED BY COPYRIGHT ALL RIGHTS ARE RESERVED NO PART OF THIS DOCUMENT MAY BE PHOTOCOPIED REPRODUCED OR TRANSLATED TO ANOTHER LAN
44. geable to the side gauge of the table so that it will be tripped at least three inches from the rearmost position of the backgauge see TRIP ROD NOTE below An extension plate is provided in the event that the sidegauge 15 not long enough washers may be required to space the switch out or in so that it aligns with the front limit switch Mount the front limit switch assembly so that it is tripped at least two inches before the backgauge contacts the false paper clamp front mechanical limit with the metal pa attached to the bottom of the clamp some clamps do not have a false paper clamp Check alignment carefully The backgauge can travel beyond these high speed limit switches in slow speed only Do not mount the switches too far from the table ends or a large amount of slow speed will occur Do not mount the switches too near the ends or the coast required to stop the backgauge on the limit switch should a runaway condition ever occur will cause a collision MICROCUT contains multiple back ups to prevent runaway conditions Several failures have to occur simultaneously in their odd failure mode to allow a runaway condition Any computer controlled drive system can fail this way no matter how many safeties are incorporated MICROCUT uses mechanical limit switches as an ultimate safeguard They must be installed properly if they are to be of any consequence TRIP ROD NOTE Mount the switches on the same side of the table as the base console The sw
45. iagnostic should cycle on during the knife stroke and not turn off until after the knife starts its upward return stroke see the NOTE in the INSTALLATION MANUAL under CUT SWITCH Check the switch adjustment to make sure the knife linkage or cam depending upon the installation is tripping it properly If so TURN OFF THE POWER AT THE WALL CIRCUIT BREAKER and check for loose wires The switch should conduct current during the knife stroke only If light 28 will not go out remove the wires to the CUT SENSING switch at terminals 7 and 8 of the ten pin terminal strip in the base console d 28 um on then there is a problem in the display console Otherwise the error is at the switch Paddle switch side loading only If the paddle switch is installed the paddle is clear of the cutter and 29 is off check the switch trip arm and adjust the switch if necessary TURN POWER OFF AT THE WALL BREAKER and check for loose wires A quadrature signal from the shaft encoder This should go on and off independently of light 31 stairstepping behavior as the shaft encoder is turned very slowly If not replace the shaft encoder See SHAFT ENCODER in this manual A quadrature signal from the shaft encoder This should go on and off independently of light 30 stairstepping behavior as the shaft encoder is turned very slowly If not replace the shaft encoder See SHAFT ENCODER in this manual Shaft encoder zero set The light will go low at the zero set and r
46. ion The display will show Press YES to save the job memory and skip the next prompt Press NO to erase all of the job memory If NO was selected press YES to erase all of the job memory If NO is pressed the job memory will be saved The display will then show Make sure the clamp and knife are both up and press the YES key The display will then show Make sure the backgauge is not tripping either limit switch Press the YES key The display will then show Use the FORWARD and REVERSE keystocheck for proper backgauge drive direction Use the YES or NO key to tell MICROCUT if the motor direction is correct MICROCUT will respond by telling you to invert the motor or the shaft encoder A and B lines see SERVICE MANUAL OR BY GOING ON TO THE NEXT PROMPT The display will show MICROCUT will move the backgauge to the rear of the table automatically Please wait MANUALLY TURN THE HANDWHEEL SO THAT THE BACKGAUGE IS AT AN EXACT INCH VALUE MICROCUT DIAGNOSTICS OK DO YOU WANT TO TEST THE MEMORY DO YOU WANT TO SAVE THE MEMORY DO YOU WANT TO ERASE THE JOBS ARE CLAMP AND KNIFE BOTH UP IS THE BACKGAUGE OFF THE LIMITS USE DRIVE KEYS IS DIRECTION OK CALIBRATING PLEASE WAIT ENTER REAR REFERENCE VALUE 0 24 Use the NUMBER and ENTER keys to tell MICROCUT the current backgauge position This is a reference value and should be as exact as possible The CM key will change units to centimeters if this is
47. itches are tripped by the trip rod assembly which can be mounted to the backgauge with the two 1 4 20 bolts and flat washers supplied The slot allows the rod to be slid towards or away from the limit switches for proper alignment If there is not room for the slotted plate the rod can be removed from the plate and mounted directly to the backgauge by its 3 8 16 threaded end In this case care must be taken to avoid breakage of the aluminum rod as it is tightened into the backgauge a common problem since the drilled hole will probably not be exactly perpendicular to the surface The mounting should be well in back of the fingers to avoid clamp interference 1 10 THE CLAMP UP SWITCH This is packed in the switch box 16 X 16 X 6 contained in BOX 2 Either one of the roller arm switches on the long slotted brackets can be used The 3 8 hardware bag in the same box contains nuts bolts and washers for mounting Use one or two 3 8 16 X 5 8 bolts with lock and flat washers to mount this switch so that it is tripped or released only when the clamp is in its full up position Note that some clamps suffer a certain amount of hydraulic sag Adjust the switch to be tripped a bit low in these cases Mount the switch to the base console side of the cutter if possible This will reduce the amount of sealtite to be strung later in the installation Some bending of the bracket may be necessary for some mounting configurations make a cut along the be
48. itching in ground There should be power at both sides of the motor when it is not being asked to operate Turn off the power AT THE WALL BREAKER Check for loose wires or worn motor brushes Voltage checks to and from the motor can be made by measuring from the black line going to the shaft encoder ground to either motor wire Voltage in high speed should be 60 130 VDC motor off Measures power through contacts of the direction relay Clean the contacts of the relay or replace Measures power through contacts of the power brake relay Clean the relay contacts or replace NOTE If the backgauge drives back but not forward or vice versa clean the direction relay contacts or replace the relay These relays are switched dry and should not fail this way If problems persist replace the console END OF ALL LIGHT CHECK S 10 25 26 27 28 29 30 31 32 ADDITIONAL DIAGNOSTIC LIGHTS CPU motor on off signal Should go on for motor on off otherwise Failure to go on represents a connection problem to the display or a display console failure The signal should be 0 volts for motor ON and 5 volts for motor OFF Processed motor on off command Should go on for motor on off otherwise Check the base console Direction relay coil Should go on for forward off for reverse Signal voltage should be Reverse O VDC forward 5 VDC Cut switch Should be off normally knife up This d
49. l equipment drive Note that only one drive system can be attached to the leadscrew at a time this prevents the possibility of one system the other In cases where an additional pulley has been added it will be necessary to electrically defeat fuses or mechanically defeat belts or gears the original equipment drive system excluding the case or a non power backgauge Mount the motor plate to the table with at least two 3 8 16 bolts with lockwashers On Pacemaker II spacers this would be to the front inside of the gearbox to align the motor with the V belt pulley on the box see NOTE The motor mounts to the plate with four 5 16 18 X 1 bolts with lock and flat washers Use one of the supplied pulleys and O E belt if possible to attach the MICROCUT motor to the backgauge drive NOTE On Pacemaker I s it will be necessary to lock the high speed clutch on Pull the cover plate off of the O E reverse drive control switch to check for the wire numbers to this switch Jumper the wires on the reverse switch to lock the high speed clutch on It will be necessary to mount the MICROCUT rear limit switch so that it trips at least three inches before the rear of the table to prevent the O E limit from negating the high speed clutch Key in a maximum rear value of less than the O E rear limit position at the SET UP ROUTINE OPERATOR S MANUAL 1 13 THE SHAFT ENCODER All parts for mounting the shaft encoder are located in the shaft encoder bo
50. l forward and backward Does the display count down moving forward and up going back Press the SETUP STEP 004 FORWARD and REVERSE keys Does the motor drive the CHECK DIRECTION backgauge in the right direction If the count or drive direction are wrong Turn the 110 VAC power to MICROCUT off Open the base console door Count direction wrong interchange the shaft encoder wires 5 amp 6 Motor direction wrong interchange the motor wires Press the REVERSE key until the backgauge reaches the rear limit switch Release the key MICROCUT will take over to calibrate 021 MANUALLY TURN THE HANDWHEEL SO THAT THE SETUP STEP 005 BACKGAUGE IS AT AN EXACT INCH VALUE THIS IS REAR POSITION INDEPENDENT OF THE MICROCUT DISPLAY Use the NUMBER and ENTER keys to tell MICROCUT the current backgauge position This is a reference value and should be as exact as possible MICROCUT will move FORWARD to the front of the table and SETUP STEP 005 stop Please wait MOVING FORWARD This is the same as when the Tear value was entered The SETUP STEP 006 backgauge must be at an exact inch value less than 10 inches FRONT POSITION Use the NUMBER and ENTER keys to enter the front reference position value Use the NUMBER and ENTER keys to tell MICROCUT how SETUP STEP 007 far forward the backgauge can move if the false paper clamp sole FALSE CLAMP ON plate is attached to the bottom of the clamp SEE NOTE AT U
51. med into MICROCUT The MANUAL key must be lit before JOB REVIEW can be started If it is not lit press the MANUAL key INSTRUCTION DISPLAY READS Press the PROGRAM key The display will show 1 NEW 2 OLD Press the 2 key LAST SAME JOB Press the 1 key and MICROCUT will ask you to select a job number See below for a description of option 2 1 CHOOSE A JOB 2 REVIEW JOBS Choice 1 Use the NUMBER keys with ENTER to select a job JOB 000 ENTER number If the number is invalid MICROCUT will prompt a DESIRED NUMBER JOB NOT FOUND error message Press 2 the computer will display the lowest programmed job number in sequence to the highest Press the NO key to see the JOB and FIRST CUT of each job programmed Press the YES key to select the displayed JOB You can now toggle the ENTER key to review the cuts on the selected job Press the AUTOMATIC key to go into AUTOMATIC MODE or the MANUAL key to go into MANUAL MODE AUTOMATIC OPERATION Select the desired job number or program a new one refer to the TABLE OF CONTENTS for sections dealing with programming and reviewing jobs Make sure that the desired job and starting cut number are displayed in the upper line of the prompting display Press the AUTOMATIC key MICROCUT will position the backgauge at the programmed stop value The AUTOMATIC key will light when the position has been achieved The CUT READY LIGHT will light whenever the backgauge is within the settling toler
52. microcut Please Note The following product manual is presented in its original form The contact information included may be outdated Please use the current contact information below Thank you C amp P Microsystems 1260 Holm Road Suite C Petaluma CA 94954 Main Number 1 707 776 4500 Fax Number 1 707 776 4555 www cp microsystems com CaP microsystems microcut installation manual Revision 498 THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION WHICH IS PROTECTED BY COPYRIGHT ALL RIGHTS ARE RESERVED NO PART OF THIS DOCUMENT MAY BE PHOTOCOPIED REPRODUCED OR TRANSLATED TO ANOTHER LANGUAGE WITHOUT THE PRIOR WRITTEN CONSENT OF GRAPHICS WEST MICRO SYSTEMS SABER MICROCUT AND MICROFACTS ARE REGISTERED TRADE MARKS OF GRAPHICS WEST MICRO SYSTEMS GMS GRAPHIC MACHINERY amp SYSTEMS A DIVISION OF GOLDEN GATE MICROSYSTEMS INC 30 Golden Gate Drive San Rafael CA 94901 Tel 415 457 7500 Fax 415 457 1964 e mail sales graphicmachinery com _http www graphicmachinery com INSTALLATION TABLE OF CONTENTS INTRODUCTION I 1 THE INSTALLATION I 2 RECOMMENDED TOOL LIST I 3 MICROCUT INSTALLATION NOTES 1 4 HINTS I 7 THE BASE CONSOLE I 8 THE LIMIT SWITCHES 1 9 THE CLAMP UP SWITCH I 10 THE CUT SENSING SWITCH I 11 THE MOTOR MOUNTING 1 12 THE SHAFT ENCODER 1 13 THE DISPLAY CONSOLE I 14 THE PADDLE SWITCH 1 15 RUNNING THE SEALTITE I 16 CONNECTING THE CABLES I 17 WIRING THE SWITCHES amp MOTOR I 18 SUPPLYING THE 110 VAC IN I 1
53. move to the first cut position O 8 INSERT CUT This routine will add a cut or an eject into the selected job number OPTION 1 PROGRAM KEY LIT IN PROGRAM OR REVIEW MODES INSTRUCTION DISPLAY READS JOB 954 CUT 010 30 000 The display will show JOB 954 CUT 010 Press the YES key INSERT CUT The display will blank out ready for you to enter a cut or eject by using the NUMBER CALCULATOR and ENTER or EJECT keys If this is a new job you can also use the FORWARD and REVERSE keys and the handwheel along with the KNIFE STROKE to enter the new cut position The KNIFE STROKE will not enter a new cut if you are in REVIEW MODE Use the ENTER or LAST key to locate the cut number to be added Press the MOD key to tell MICROCUT you want to modify the job OPTION 2 CUT READY LIGHT ON IN AUTOMATIC MODE INSTRUCTION DISPLAY READS JOB 954 CUT 010 CHANGE CUT Y N JOB 954 010 Answer NO to the question LAY COMP The display will show JOB 954 CUT 010 Press the YES key INSERT CUT The display will blank out ready for you to enter a cut or eject by using the NUMBER CALCULATOR and ENTER or EJECT keys You can also use the FORWARD and REVERSE keys and the handwheel along with the KNIFE STROKE to enter the new cut position Press the MOD key The display will show Press the NO key O 9 DELETE CUT This routine will remove a cut or eject from memory in the selected job number
54. n this manual BASIC TROUBLESHOOTING and THE SHAFT ENCODER CUT STROKE EARLY MICROCUT is not in position for the knife stroke but it senses that the knife is being operated Bring the knife back up to the top of its stroke and allow MICROCUT to position the backgauge correctly See the prompt OUT OF POSITION CUT SWITCH HAS A WIRING PROBLEM MICROCUT senses that the knife is down when it is supposed to be up Check the wires for proper connection see the INSTALLATION MANUAL DIAGNOSTICS OK MICROCUT wants you to check the first 24 diagnostic lights in the base console to make sure everything is operating properly Refer to the section DIAGNOSTIC LIGHTS in this manual DRIVE OVERHEATED WAIT FOR COOLING The backgauge drive circuitry has been run hard enough to heat past 80 of its rated capability MICROCUT will not allow additional drive until the components cool down adequately See the prompt OIL LEADSCREW OR REDUCE SPEED S 12 ERROR CORRECT POSITION UNKNOWN MICROCUT has lost the ability to know where the backgauge is accurately It will be necess turn the power off and start again Refer to other sections of this manual BASI TROUBLESHOOTING and THE SHAFT ENCODER FAST DRIVE PROB MICROCUT has not detected any motion during a period of time when the backgauge should have been moving This may be due to either a drive or a counting error If the backgauge moves a bit and then stops MICROCUT is not seeing the motion and has a c
55. nd This should be on for high speed off for slow Entrance to the SET UP ROUTINE DIAGNOSTICS OK prompt automatically sets up for high speed Check for a bad connection between the base console and display Replacement of the display console or the cable may be necessary Voltmeter ae of the speed signal can be obtained signal 0 volts for fast 5 volts for slow iue command If 15 was on 16 is not replace the 7404 the base console Measures the motor power supply Failure here indicates a bad heatsink triac 2N5445 or a bad opto triac MOC3010 Replacement of the base console is recommended Verify this light by measuring for between 60 and 90 VDC between the top of the 2N5445 triac and the black line going out to the shaft encoder bottom terminal strip system ground Measures the CPU drive system enable line master reset If cycling the power on and off does not cure this replacement of the display console or cable may be necessary Measures the motor power brake relay coil A non lit condition here probably indicates a blown FET Refer to the BASIC TROUBLESHOOTING section of this manual A welded shut FET bypass relay can also cause this problem Measures power through contacts of the power brake relay Clean the contacts or replace the relay Measures power through contacts of the direction relay Clean the contacts or replace Measures power through the motor NOTE the motor isturned on by sw
56. ng as the CUT READY LIGHT is ON NOTE If the backgauge is knocked behond the settling tolerances see 2 steps further on THE TRUE POSITION WILL THEN BE SHOWN UNTIL THE SETTLING TOLERANCES ARE SATISFIED AGAIN NOTE The false clamp is a metal plate which attaches to the bottom of the clamp for some paper cutters It is removed to make very short cuts This requires two different front travel limit values If there is not a false clamp then the two front travel limit values will be the same Press the YES key if you want MICROCUT to reposition the backgauge if it is knocked out of settling tolerance in AUTOMATIC MODE see directly below Enter to 9 The larger the number the faster MICROCUT settles Usually 2 or 3 is recommended Poorly maintained machines may require larger values O 25 SELF CORRECTION IN AUTOMATIC TOLERANCE IS 0 003 INCHES NOTE If the tolerance is set too small the CUT READY LIGHT will have a tendency to flicker on and off when MICROCUT reaches the stop position in AUTOMATIC MODE This flickering will not damage MICROCUT but it does tend to be annoying to the operator Refer to INSTALLATION NOTES in the INSTALLATION MANUAL for tips on improving the settling capability of MICROCUT Answer the question If YES is pressed MICROCUT will drive the backgauge to the full rear of the table at the end of each job sequence IF youanswered YES above do you want MICROCUT to automatically move to the fi
57. ng much easier I4 MICROCUT INSTALLATION NOTES The paragraphs cover most of the installation failures seen to date Please read them carefully A Optimum performance is obtained when the motor is geared for 4 turns for every inch of backgauge drive A smaller turn ratio causes the backgauge load to slow the motor down The current used by the motor goes up accordingly The power that the system uses nm up as the square of this current Unless the motor is operating at its full 1800 rpm and the high speed adjusting potentiometer is less than 100 SPEED WILL NOT BE INCREASED BY DECREASING THE MOTOR TURNS RATIO THE BACKGAUGE RESISTANCE WILL FORCE THE MOTOR TO RUN OUT OFITS PREFERRED RPM RANGE THIS WILL CAUSE EXCESSIVE POWER USE AND MOTOR BRUSH WEAR AFTER THE MOTOR IS INSTALLED HAVE SOMEONE TURN THE HANDWHEEL TO MOVE THE BACKGAUGE FORWARD ONE INCH WATCH THE MOTOR PULLEY DURING THIS TIME TO COUNT THE NUMBER OF TURNS IT MAKES IFIT DOES NOT TURN AT LEAST THREE TIMES AND PREFERABLY FOUR TIMES THEN THE MOTOR PULLEY IS TOO LARGE TO PREVENT EVENTUAL FAILURE CORRECT THIS SITUATION IMMEDIATELY B A variable groove pulley is supplied so that the motor turn ratio see A above can be approximated in most cases When the my is adjusted properly snug the locking allen set screw to the FLAT of the rock the pulley gently to position the set screw on the center of the flat then completely tighten it This will prevent the pulle
58. nt edges to do this Alternatively the 3 8 16 X 12 threaded rod may be cut to length to space the switch out to meet the clamp A 2 X 2 X 2 angle piece is included to be used as a trip plate if needed This can be mounted with one or two 1 4 20 X 1 2 bolt s with lockwasher s NOTE It may be helpful to plan the SHAFT ENCODER mounting first There will usually be a spare right angle bracket which may be useful when mounting the CLAMP UP SWITCH in certain instances I 11 THE CUT SENSING SWITCH DO NOT INTERFERE WITH ANY PART OF THE ORIGINAL EQUIPMENT KNIFE CIRCUIT ANY ALTERATION TO EITHER THE KNIFE OR CLAMP CIRCUITS SAFETIES AND MECHANISMS IS EXPRESSLY FORBIDDEN This is packed in the switch box 16 X 16 X 6 contained in BOX 2 Either one of the roller arm switches on the long slotted brackets can be used The 3 8 hardware bag contains nuts bolts and washers for mounting There is a spring lever arm in one of the other hardware bags which can be used to trip the cut sensing switch in certain mounting applications Use one or two 3 8 16 X 5 8 bolts with lock and flat washers to mount this switch so that it cycles on off on or off on off during the knife stroke Use the original equipment knife cam if possible since cams generally give smoother action than moving mechanical parts DO NOT INTERFERE WITH ANY PART OF THE ORIGINAL EQUIPMENT KNIFE CIRCUIT MAKE SURE THAT THE O E SWITCHES ALREADY MOUNTED ON THE CAM ARE WELL CLEAR OF
59. o set If the count is too far out of tolerance the microprocessor will shut the backgauge drive off and signal the operator in the prompting display ERROR CORRECT POSITION UNKNOWN Refer to the BASIC TROUBLESHOOTING and PROMPT ERROR MESSAGE LIST sections of this manual
60. or tip from a tube of silicone seal works well to remove the lights Needle nose pliers work also but tend to break the glass S 6 17 AUTO ADVANCE DOES NOT OPERATE AFTER SIDE LOAD a Auto advance was not selected If so the MOVE key will advance the backgauge See the OPERATOR S MANUAL MODIFICATIONS b The paddle switch was not activated Refer to light 29 in the DIAGNOSTIC DA em NOTE for auto advance to work a paddle switch MUST installed DRIVE TROUBLESHOOTING MICROCUT has several safety and internal checks which can negate backgauge drive Three of these are centered with the computer the rest are in the drive system itself Check the computer symptoms before opening the base console door which will interrupt power to MICROCUT and turn it off The computer safety overrides are 1 Master Reset If the displays come on properly at power up then master reset is fine Failure would imply a problem in the computer or base console power supply Refer to the DIAGNOSTIC LIGHTS section Diagnostic light 18 will be unlit 2 Count OK MICROCUT S intelligent counting system checks for an out of tolerance condition every time the shaft encoder passes its internal zero set the shaft encoder is the device attached to the leadscrew which puts out rotational counting pulses and enables MICROCUT to sense backgauge position If an out of tolerance condition exists MICROCUT will immediately disable the drive system If this hap
61. ot erased at the time of installation Enter the SETUP ROUTINE and erase the job memory see the OPERATOR S MANUAL SET UP ROUTINE 13 OUT OF MEMORY a Memory was not erased at the time of installation Enter the SETUP ROUTINE and erase all of the job memory see the OPERATOR S MANUAL b A Allofthe memory space has been used Delete unused jobs as desired or enter the SET UP ROUTINE and erase all of the job memory see the OPERATOR S MANUAL 14 CUT READY LIGHT FLICKERS ON AND OFF a The settling tolerances are set at too small a value Refer to OPERATOR S MANUAL MODIFICATIONS b There is a connection oe at the CUT READY socket on the display board or the light is burned out 15 CUT IS NOT RECOGNIZED a The cut sensing switch is out of adjustment Check LED 28 for cyclical operation Adjust the switch as necessary This switch can be located by following the cut switch wires out of the base console Refer to the INSTALLATION MANUAL WIRING THE SWITCHES AND MOTOR for the location of these wires Also see the INSTALLATION MANUAL CUT SWITCH 16 BACKGAUGE DRIVES INTO THE FALSE CLAMP WITHOUT STOPPING a false clamp option is incorrect See the OPERATOR S MANUAL MODIFICATIONS NOTE The key caps pry off Bulbs can be replaced from the front side without disassembly of the display console It is recommended that power be turned off Double wide keys may have only one bulb burned out A cut off applicat
62. ounting problem If no motion occurs then MICROCUT is suffering from a drive error Refer to other sections of this manual BASIC TROUBLESHOOTING and THE SHAFT ENCODER FRONT LIMIT ERROR MICROCUT has sensed that the front limit has tripped even though it should not have Check the switch carefully FRONT LIMIT HAS A WIRING PROBLEM MICROCUT senses that the front limit is tripped when it is not supposed to be Check the wires for proper connection see the INSTALLATION MANUAL INVERT CLEAR AND BLUE WIRES The shaft encoder is counting in the wrong direction SET UP ROUTINE for new installations only It will be necessary to invert the signal A and B wires from the encoder to continue Refer to the ENCODER SERVICE INSTALLATION MANUALS WIRING CABLES sections INSTALLATION MANUAL elsewhere in this documentation NOTE On some cables these wires are white and yellow INVERT MOTOR WIRES The motor is driving in the wrong direction SET UP ROUTINE for new installations only It will be necessary to invert the motor wires so that the motor can drive in the right direction before setting up MICROCUT to operate on its new machine JOB NOT FOUND The old job that was manually selected is not in the job memory Try a different job number or review all of the jobs JOB NUMBER USED The new job that has been manually selected is already programmed It will be necessary to choose a different number or erase this number
63. parts are not user serviceable The display console has been designed with a universal mount and a plug in connecting cable so that it is very easy to remove and exchange This would be the procedure for any serious problems in the computers There are however a number of problems that can be taken care of in regard to the computers They fit into four basic categories 1 Operational 2 Counting 3 Memory 4 Miscellaneous There is overlap in these categories To simplify the matter the following pages contain titles of possible problems and steps to take if a problem does exist During thunderstorms or in the event of an electrical disturbance it is possible for any computer to lose track of itself If such a failure occurs turning the power off and then back on should correct it See the note in the FOREWORD of this manual NOTE MICROCUT uses non volatile memory for job data storage There are no batteries Memory will last indefinitely Every time MICROCUT manipulates memory it double checks all alterations The 5 VDC supply is self adjusting No maintenance of any sort is necessary in the display console 5 3 1 MICROCUT WILL NOT SWITCH ON a b ap The power switch on the display console has not beentoggled The base console door is open and the door interlock switch has not been defeated units before 1987 only have this interlock switch later units need not be concerned with this The wall circuit breake
64. pens the current position display will be blank and the prompt displa will read ERROR CORRECT POSITION UNKNOWN Diagnostic 18 will be unlit If counting failures persist refer to the BASIC TROUBLESHOOTING and the SHAFT ENCODER sections of this manual 3 Motor On Off Command This should operate only when commanded If operating properly diagnostic 25 will light for motor drive All other motor drive problems would center around the base console mounted on the side or back of the cutter Refer to the following section for these S 8 DIAGNOSTIC LIGHTS NOTE Diagnostic lights are no more reliable than the solid state circuitry which they monitor Before making absolute decisions a voltage reading should be taken to make sure the failure isn t in the light itself The du are supplied for convenience only and do a remarkably good job when properly A light s failure mode is for it to be unlit Therefore all checks require a lit condition A door safety interlock automatically shuts off power to MICROCUT when the base console door is swung open units before 1987 only If AC power is still supplied to the box only diagnostic 1 will be lit To defeat the interlock pull straight out on the plunger until it snaps into position Now assuming the ON OFF switch on the display console is off only diagnostics 1 through 4 should come on In order to troubleshoot the system it will be necessary to enter the SET UP ROUTINE refer to th
65. r has been turned off or is tripped The cable between the base console and the display is disconnected or poorly connected Refer to the section DIAGNOSTIC LIGHTS in this manual 2 MICROCUT DEFAULTS INTO SET UP ROUTINE a b The power is being disconnected and reconnected at the 110 VAC source Use the switch supplied on the back of the display console only see OPERATOR S MANUAL TURNING POWER ON TO MICROCUT The 110 VAC line into MICROCUT is inadequate Check the ground and verify that the circuit is dedicated and capable of supplying 30 amps see the INSTALLATION MANUAL 110 VAC IN 3 NO BACKGAUGE DRIVE Bo of The motor belt or pulley is loose There is a mechanical bind preventing drive A fuse is blown Check the fuses and replace if necessary The motor speed adjusting potentiometers are set too low to overcome the backgauge drive resistance Check these adjusting potentiometers in the center area of the base console and turn them more towards 100 See ADJUSTING MOTOR SPEEDS in this manual There is a bad FET on the power board in the base console Check for diagnostic light 19 when MICROCUT is in the SET UP ROUTINE AND the prompt reads DIAGNOSTICS OK BOARD REV C use a soldering iron to lift the center leg of one FET there are 3 FETs labeled on the power board in the base console at a time Turn the power back on and check for drive When drive is obtained solder previously removed FETs in one at a time and r
66. rew it back into the consoles at either end Make sure that there is adequate strain relief so that the connector will not be damaged if the display console is pivoted on its mounting base Use a small screwdriver to check for tightness on all of the wire connections Unplug the connector on the shaft encoder and plug it back in several times Check all wiring for any nicks or cuts Pull out the relays in the base console and reinsert them several times to make sure that they are well connected to the power board TLDS Occasionally check all of the MICROCUT components switches motor shaft encoder display and base consoles to make sure none of the mounts have loosened Tighten as necessary DO NOT USE GREASE ON THE LEADSCREW MECHANISM GREASE ATTRACTS ABRASIVE DIRT AND ACTS AS AN INCONSISTENT CUSHION AGAINST THE BACKGAUGE PREVENTING PROPER CUTTING PRECISION USE A LIGHT MACHINE OIL ONLY ON THE LEADSCREW OIL THE LEADSCREW DAILY MICROCUT JOB MEMORY WILL NOT BE ALTERED ALL OF THE JOBS WHICH WERE PEDIS UMEN BEFORE MAINTENANCE WILL STILL BE PROGRAMMED AFTERWARDS S 18 THE SHAFT ENCODER The shaft encoder is attached to the leadscrew mechanism with a chain It sends out two different signals as the leadscrew rotates so that the computer can measure backgauge movement A zero set is internal to the shaft encoder as well to allow the computer to keep track of each complete revolution The MICROCUT shaft encoder is an incremental qua
67. rive sometimes it is necessary to remove drive belts or fuses for electric backgauge brakes or add switches to activate drive clutches ANY ALTERATIONS TO THE PAPER CUTTER TO ACCOMMODATE MICROCUT INVOLVE THE BACKGAUGE DRIVE ONLY NO ALTERATION TO ANY OTHER PART OF THE MACHINE IS ALLOWED Follow the instructions written below by the installer to convert the machine back to its original equipment drive microcut service manual Revision 498 THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION WHICH IS PROTECTED BY COPYRIGHT ALL RIGHTS ARE RESERVED NO PART OF THIS DOCUMENT MAY BE PHOTOCOPIED REPRODUCED OR TRANSLATED TO ANOTHER LANGUAGE WITHOUT THE PRIOR WRITTEN CONSENT OF GRAPHICS WEST MICRO SYSTEMS SABER MICROCUT AND MICROFACTS ARE REGISTERED TRADE MARKS OF GRAPHICS WEST MICRO SYSTEMS GMS GRAPHIC MACHINERY amp SYSTEMS A DIVISION OF GOLDEN GATE MICROSYSTEMS INC 30 Golden Gate Drive San Rafael CA 94901 Tel 415 457 7500 Fax 415 457 1964 e mail sales graphicmachinery com _ http www graphicmachinery com SERVICE TABLE OF CONTENTS FOREWORD S 1 BASIC TROUBLESHOOTING S 2 DRIVE TROUBLESHOOTING S 7 DIAGNOSTIC LIGHTS S 8 PROMPT ERROR MESSAGE LIST S 11 ADJUSTING MOTOR SPEEDS S 16 MAINTENANCE S 17 THE SHAFT ENCODER S 18 5 1 FOREWORD MICROCUT is designed to be very easy to service and maintain The spacer can be divided into two main s sense the motor drive and the computer The motor drive has diagnostic lights in th
68. rst cut after side loading is done PADDLE SENSE SWITCH REQUIRED Press YES to have the backlighting for the prompt display ON Press NO to turn it off MICROCUT now knows what type of machine it been installed on and is ready to use SIDE LOADING YES OR NO AUTO ADVANCE AFTER SIDE LOAD PROMPT DISPLAY BACKLIGHTING Y N TURN POWER OFF RESTART TURN THE POWER OFF AND BACK ON The display will read PRESS AUTOMATIC TO START You are ready to operate MICROCUT O 26 IN MM CM COMPARISON TABLE INCHES MM CM Bait icc serene TO 127 10 254 25 4 T ta a ana eee eer E o bete Le E 38 41 20 508 50 8 e unde cni eee 635 Seat enable 63 5 30 762 76 2 Sos ose die ee eee 88 9 40 1016 101 6 ds nouus tea ones euese ce cac 50 1270 127 0 Ob abe eee ee ee eee tS ee ee 139 7 60 1524 152 4 S IGG ees a 165 1 70 1778 177 8 ee ee ee ee 190 5 80 2032 203 2 iene ees eats 215 9 90 2286 228 6 esent crei M 241 3 100 2540 254 0 ERU JOO ee eee ee 266 7 110 2794 279 4 INCHES CM 2 54 MM 25 4 CM MM 10 2 54 x INCHES MM 25 4 x INCHES 10 x CM 0 27 USE OF ORIGINAL EQUIPMENT CONTROLS MICROCUT uses its own drive motor To insure that this does not conflict with the original equipment d
69. screws to secure all sealtite and cabling 2 Move backgauge so that it is at least ten inches from either end of the table limits 3 Turn the power on to both the cutter and MICROCUT 4 Refer to the SET UP ROUTINE in the OPERATOR S MANUAL to calibrate to the cutter it is now installed on NOTE TO MAKE SURE THAT ALL OF THE SWITCHES ARE WIRED AND OPERATING PROPERLY REFER TO THE TABLE BELOW DURING THE DIAGNOSTICS CHECK IN THE SET UP ROUTINE LIGHT 10 11 12 28 29 FUNCTION REAR LIMIT FRONT LIMIT CLAMP SWITCH CUT SENSE PADDLE SENSE ON WHEN OK TO DRIVE OK TO DRIVE OK TO DRIVE CUTTING OK TO DRIVE OFF WHEN DRIVE DISABLED DRIVE DISABLED DRIVE DISABLED KNIFE UP PADDLE OUT IF ANY OF THE SWITCHES ARE INCORRECT AT THIS POINT TURN THE POWER OFF AND CORRECT BEFORE PROCEEDING REFER TO THE DIAGNOSTIC LIGHTS SECTION IN THE SERVICE MANUAL FOR ASSISTANCE IF NECESSARY 1 21 FINAL CHECKOUT 1 Inspect all components and cables for tightness alignment and routing 2 Add additional guarding as required to insure full operator safety Check around all parts and assemblies which were added or affected by the addition of MICROCUT Make sure that all moving parts or hazards are guarded fully MICROCUT CONSISTS OF PARTS AND ASSEMBLIES WHICH ARE ADDED TO THE MACHINE GUARDING MAY NEED TO BE ALTERED OR ADDED TO OFFER PROPER PROTECTION THIS MUST BE DONE BEFORE MICROCUT IS OPERATED DO NOT OPERA
70. se NUMBER and ENTER keys to tell MICROCUT how SETUP STEP 008 far forward the backgauge can move if the false paper clamp is off MOST FORWARD SEE NOTE AT BOTTOM OF PAGE Use the NUMBER and ENTER keys to tell MICROCUT how far back the backgauge can be driven before the mechanical stop Answer the question FALSE PAPER If there is no false clamp press either the YES or the NO key CLAMP ON Y N NOTE The false clamp is a metal plate which attaches to the bottom of the clamp for some paper cutters It is removed to make very short cuts This requires two different front travel limit values If there is not a false clamp then the two front travel limit values will be the same SETUP STEP 009 MAXIMUM REAR 22 Press the YES key if you want MICROCUT to reposition the backgauge if it is knocked out of settling tolerance in AUTOMATIC MODE see directly below Enter 1 to 9 The larger the number the faster MICROCUT settles Usually 2 or 3 is recommended Poorly maintained machines may require larger values SELF CORRECTION IN AUTOMATIC TOLERANCE IS 0 003 INCHES NOTE If the tolerance is set too small the CUT READY LIGHT will have a tendency to flicker on and off when MICROCUT reaches the stop position in AUTOMATIC MODE This flickering will not damage MICROCUT but it does tend to be annoying to the operator Refer to INSTALLATION NOTES in the INSTALLATION MANUAL for tips on improving the settling capability of
71. sidegauge or on the rear of the cutter housing Where necessary longer cables can be ordered This may involve some lead time and an additional charge for the service The cut sensing switch should not finish its activation cycle until the knife is well past bottom dead center On some cutters release of the hand switches will return the clamp to the top while leaving the knife at mid stroke If the cut sensing switch completes its cycle before the knife passes bottom dead center and assures itself of an uninterrupted completion of cycle and the hand switches are oe MICROCUT may push the paper forward into the blade trying to drive to the next stop value On some paper cutters the clamp and knife can only be operated together In this case activation of either one implies activation of the other This will be found on certain mill trimmers Only one switch need be mounted for both the CLAMP and CUT sense Wire the cut switch to the open contacts clamp up The up switch will wire to the closed Note Some city codes allow ony two wires per piece of sealtite In this case both switches should be used with two pieces of sealtite accordingly Lay out the ENTIRE mechanical installation BEFORE drilling any holes Visualize the entire installation to be sure all cables will reach and can be run smootbly Use a small amount of silicone spray spray oil or water inside the end of the sealtite before stuffing the wire through This will prevent
72. stop position in AUTOMATIC MODE This flickering will not damage MICROCUT but it does tend to be annoying to the operator Refer to INSTALLATION NOTES in the INSTALLATION MANUAL for tips on improving the settling capability of MICROCUT Answer the question If YES is pressed MICROCUT will drive the backgauge to the SIDE LOADING full rear of the table at the end of each job sequence YES OR NO IF you answered YES above do you want MICROCUT to automatically move to the first cut after side loading is done ie SEIL PADDLE SENSE SWITCH REQUIRED Press YES to have the backlighting for the prompt display ON PROMPT DISPLAY Press NO to turn it off BACKLIGHTING Y N MICROCUT can be calibrated for errors up to 3 8 of an inch If the error is more the mechanical condition of the machine should CALIBRATE GAUGE be closely inspected If you say YES move the backgauge to a YES OR NO known position use the NUMBER keys to display that value in the prompt and press the ENTER key Calibration requires that the backgauge be squared first the gibbs should be adjusted for this Cut a trimmed lift of stock at 20 inches MICROCUT Move the backgauge to 10 inches MICROCUT and cut the stock again Remove the top inch of the stock in each pile to remove the knife draw Flip the front pile which is exactly 10 inches long over and place it on top of the back pile Compare the lengths Most people can feel a few thousandths This is much more acc
73. uires a full restart to recalibrate Turn the power off then back on and press the AUTOMATIC key to start S 16 ADJUSTING MOTOR SPEEDS Open up the base console door There are two potentiometers one labeled for the high for slow Adjusting these towards 100 will increase the speed each is labeled for Adjustment towards 0 decreases the motor speed NOTE Early units had four potentiometers In this case adjust the ones marked speed to 100 Use the power potentiometers to control the backgauge velocity S 17 MAINTENANCE MICROCUT has been designed to be virtually maintenance free Memory is non volatile requiring no battery backup The power supplies are self adapting The 1 3 and 1 2 horse power motor brushes should be checked every 5000 hours of operation The brushes in the 3 4 and horse power motors should be checked every 1000 hours of operation 500 hours on very large or stiff tables for wear Replace as appropriate Clean the motor of carbon dust as required CAUTION Turn power off AT THE WALL BREAKER before checking the motor brushes Connections can cause problems in any electrical circuit To avoid problems with connections it is advised that once a year a tune up be performed 1 Turn the power for MICROCUT off at the wall breaker 2 Unplug the cable which connects the display console to the base console at both ends Plug it in and out several times at each end to clean the connecting pins Sc
74. uld be experienced if a V belt were wrapped on this diameter Mounting space on the leadscrew does not allow for a sprocket to be mounted as well so the shaft encoder sprocket is mounted onto the motor shaft This does not require a split sprocket either 1 14 THE DISPLAY CONSOLE The display console is located in the center section of BOX 1 along with the display cable The Panavise mounting bracket and flathead allen screw hardware bag are packed in the miscellaneous box 10 X 16 X 6 contained in BOX 2 The display console should mount on the front of the cutter near the operator but out of his way as he works Watch the operator work to see if he has a tendency to swing paper to one side or the other during loading aud unloading Also watch to see which side of the cutter he works towards A ball joint mounting assembly Panavise is supplied Attach this to the cutter with three 1 4 20 X 1 2 allen flathead screws Place the display mounting rod onto the ball joint assembly and tighten slightly The display arm which connects to the ball joint can be installed with either the short or the long side down The display can be positioned as necessary by swinging the ball joint and tilting the yoke assembly Avoid mounting the console to thin hollow guards which may subject it to undue vibration 1 15 THE PADDLE SWITCH SIDE LOADING ONLY If ordered the paddle switch and all mounting brackets and hardware are shipped in their own box
75. urate than a ruler DO NOT USE GREASE ON THE LEADSCREW MECHANISM GREASE ATTRACTS ABRASIVE DIRT AND ACTS AS AN INCONSISTENT CUSHION AGAINST THE BACKGAUGE PREVENTING PROPER CUTTING PRECISION USE A LIGHT MACHINE OIL ONLY ON THE LEADSCREW OIL THE LEADSCREW DAILY O 20 SETTING UP MICROCUT 1 Turn the power ON to MICROCUT Wait for the MEMORY TEST to complete If the display says PRESS AUTOMATIC TO START DON T press the AUTOMATIC key but instead press and hold any NUMBER key and then press the PROGRAM key Release both keys and this will take you into the SETUP ROUTINE NOTE MICROCUT software comes in two different SET UP ROUTINE versions If the prompts appear differently than listed here refer to the ADDENDUM TO SETTING UP MICROCUT see the TABLE OF CONTENTS The first 24 lights in the base console should be on If not stop here and see DIAGNOSTIC LIGHTS in the SERVICE MANUAL If all lights are on press the YES key SETUP STEP 001 DIAGNOSTICS OK The display will show SETUP STEP 002 Press NO to save the job memory and skip the next prompt CLEAR MEMORY Y N Press YES to erase all of the job memory If YES was selected press NO to erase all of the job memory If SETUP STEP 002 YES is pressed the job memory will be saved SAVE JOBS YES NO The display will show The memory test is non destructive the job memory won t be SETUP STEP 003 altered Press YES NO to this option MEMORY TEST Turn the handwhee
76. will flash the positions as MICROCUT calculates them MICROCUT stays in the PROGRAM mode to allow additional job programming as desired SHEET DIVIDE This routine is used WHILE IN THE PROGRAMMING MODE to divide a sheet into equal sizes It is useful for spreading a size error equally when splitting an undersized sheet into logs The PROGRAM key must be lit see PROGRAMMING A NEW JOB INSTRUCTION DISPLAY READS Press the PROGRAM key The display will show JOB 954 CUT 001 Press the NO key STEP amp REPEAT Y N The display will show JOB 954 CUT 001 Press the YES key DIVIDE SHEET Use the NUMBER keys with ENTER or the KNIFE JOB 4954 CUT 001 STROKE to enter the sheet size The NUMBER keys are ENTER SHEET SIZE allowed to key in a value up to twice the maximum rear Use the NUMBER keys and ENTER to tell MICROCUT what to CUL divide the sheet by DIVIDE BN If the sheet size was entered with a KNIFE STROKE this prompt JOB 4954 CUT 001 will not be shown Press the YES key if the sheet needs to be BACKTRIM SHEET cut to initial size NOTE If the first calculated stop is greater than the maximum rear limit MICROCUT will give you a TOO FAR BACK error message The LOWER LINE of the prompt display will flash the positions as MICROCUT calculates them MICROCUT stays in the PROGRAM mode to allow additional job programming as desired JOB REVIEW This routine is used to select or review jobs which have already been program
77. witch blocks in the CUT and CLAMP sensing switches will try to slip out during wiring if the switch is mounted in the tripped position It may be necessary to loosen the switch mount to install the wiring while the switch is in its relaxed position If this 15 not done the switch may not operate properly cut switch DOES NOT conduct current when the knife is up All other switches will NEGATE backgauge drive unless they ARE CONDUCTING current The clamp sensing switch will negate all backgauge drive The limit switches will negate high speed drive in their appropriate direction S Make sure that all wires are securely tightened BEFORE operating the spacer 1 6 T 1 4 20 threaded rod in the kit is for motor mounting on most Harris Sabers and Citations The slots on the rear of the motor mounting plate can be used to sandwich the plate under the OE rear limit switch bracket The 1 4 20 rod supports the plate caddy corner to this The SET UP ROUTINE OPERATOR S MANUAL has been simplified Read the prompting display It will tell you what to do in order to calibrate MICROCUT into its new machine V NOTE ON SIDELOADING The paddle switch is used to sense when the side load has taken place and when the paddle has cleared the table It DOES NOT sense whether the paper is loaded properly and WILL NOT prevent jam ups It is used only to auto advance the backgauge after a side load has been completed For absolute safety an opto
78. x 6 X 16 X 6 contained in BOX 2 MICROCUT uses a shaft encoder with internal zero set to keep track of backgauge position The shaft encoder is driven off the leadscrew with a sprocket chain sprocket arrangement The sprocket for the leadscrew is split to allow for easier attachment to the leadscrew see NOTE below Use the shaft encoder plates supplied to mount the shaft encoder near an unthreaded part of the leadscrew This can usually be done without any drilling or tapping to the cutter Play with the brackets a bit before you jump to any conclusions about how to mount the shaft encoder Clamp the split sprocket to the leadscrew so that it lines up with the shaft encoder sprocket Measure and break the drive to length Install it to the sprockets Take up any slack with the shaft encoder swing mounting racket Make sure that the split sprocket is mounted so that there is no undue stress on the chain at the junction of the sprocket halves NOTE This is not always the case Polars require that the sprocket be mounted to an extension rod off of the back of the leadscrew the 3 8 16 threaded rod works beautifully for this purpose replace the existing bolt or rod and the sprocket need not be split On Senators with O E gearbox drive it is necessary to use a small motor drive gear at the back of the table small because of available space The small size requires that this be a cogged gear to prevent belt slippage and power loss which wo
79. y from self adjusting itself later on down the d If the adjustable groove pulley is too large use the other pulley supplied with the installation 1t C MICROCUTisa totally redundant system specifically designed to operate independently of a machine s existing controls The use of existing limit switches terminal blocks etc is expressly forbidden and their use will result in the warranty being voided D PERFORMANCE thick drive belts B size slow down positioning Use an A sectional belt or thinner if possible Do not overtorque the backgauge gibbs and if there are nylon glider plugs in the backgauge make sure they are not tight Vd the table there should be at least 002 clearance Make sure the motor turns at least three times and preferably four times per inch of backgauge travel This will give MICROCUT enough leverage osition quickly O NOT USE GREASE ON THE LEADSCREW MECHANISM GREASE ATTRACTS ABRASIVE DIRT AND ACTS AS AN INCONSISTENT CUSHION AGAINST THE BACKGAUGE PREVENTING PROPER CUTTING PRECISION USE A LIGHT MACHINE OIL ONLY ON THE LEADSCREW OIL THE LEADSCREW DAILY to drive smoothly and settle into E Supply the proper DEDICATED 110 VAC power line The computer competes against the drive motor for its current The motor by its very nature is a better competitor Therefore MICROCUT requires a power supply capable of giving 30 amps If a transformer is used at 110 V AC the minimum size would be a i KVA 5 KVA is better

Download Pdf Manuals

image

Related Search

Related Contents

Winch et Manivelle - Technique greement  Tripp Lite B004-VUA2-K-R User's Manual    Bedienungsanleitung Mobilgerät D400  La fixation du niveau des pensions alimentaires  Patriot Memory PCTGI6W screen protector  固定式 舟形桟  User Manual  June - SA Boerperd  

Copyright © All rights reserved.
Failed to retrieve file