CCB SERVICE MANUAL
Contents
1. SEE ATTACHED VIDEO 1 Prebuilt Filename Bring up the HEX file 2 Family 16 bit MCUs PIC24 3 Device PIC24FJ64GA306 4 Supported Debug Header None 5 Hardware Tool PICkit3 6 After the above setting click NEXT NEXT Finish CRANE SCALE CCB SERIES 6 Set the Project Properties File Project Properties SEE ATTACHED VIDEO 1 Click PICkit3 in Categories 2 Option categories Memories to Program 3 Preserve Program Memory Select 4 Preserve Program Memory Start hex 0 0800 5 Preserve Program Memory End hex OXTFFF 6 After the above setting click Apply 7 Option categories Power 8 Power target circuit from PICkit3 Select 9 After the above setting click Apply OK Upgrade firmware SEE ATTACHED VIDEO 1 Click the Make and Program Device icon 2 Confirm the complete message2. CRANE SCALE CCB SERIES SERIES VER 001 CCB SERVICE MANUAL CRANE SCALE CCB SERIES 1 Calibration amp Gravity compensation 2 Wireless Pairing 3 Exploded View 4 Firmware Update CRANE SCALE CCB SERIES 1 Calibration amp Gravity Compensation 1 1 Calibration When the power is off press while pressing When G CAL is displayed and then press Then this calibration mode is started TITLE KEYBOARD amp DESCRIPTION How to enter amp Program version Move to a next step in automatic Initialized value Maximum capacity numeric increase scale increase save decrease Increase Minimum division Ge save Initialized value Setting weight numeric increase scale increase save Setting weight shall be within the range of 10 100 of max capacity ra Zero calibration Unload the tray and press Load the weight which was set in step 5 Span calibration and press Finish Unload the tray and press CRANE SCALE CCB SERIES 1 2 Gravity compensation When the power is off press while pressing When G CAL is displayed and then press again Then this gravity compensation mode is started TITLE KEYBOARD amp DESCRIPTION How to enter gt Program version Move to a next step in automatic Initialized value Calibration location ares 9 799m s Hog scale increase 9 save brc Aud Initia
3. he green light is blinking Pairing When FSEL is displayed at both products if you press key of CCB crane scale pairing will finish Z Please check Eng message at both products CRC 200 green light will be turn on If ending message is not appear please repeat the pairing 3 Exploded view CRANE SCALE CCB SERIES LC COVER ST Round Head Wrench Bolt WBRH M10 x 25 SPEC PLATE 1 2 95 x 40 1 3 2 code stopper M12x8 RIVET BLIND 2 5 power cable 2 5x400 code stopper SHACKLE 5T LOADCELL CSS1T CSS3T CSS5T 5510 hook assy crosby 1T 3T 5T 10T BATTERY PACK ASSY CBP 100 PCB LCD PCB LCD FRONT PANEL 201x121x20 keypad tbs 1 1 1 1 1 1 1 1 169x29 capa decal TCB GASKET 1 64 5x6 1 FH M4x16 10 200x120x3 5 CRANE SCALE CCB SERIES 4 Firmware Update 1 Install the MPLABX 2 Run MPLAB X IDE 3 Connect the PICkit3 to PC 4 Connect as shown in the picture below Aligned the RED wire and arrow mark of PCB and then combines them gt gt Onc MURUS PEN e TACTO 42444 U 1 C 114444 ina te v esos _ P CIS CN C EL m Lx ds RM 454 A J E t 5 4 9x ozu LW 5 Select the HEX file File Import Hex ELF Prebuilt File
4. lized value a Using location 3133 numeric increase 9 799m s scale increase 9 save Finish End Unload the tray and press If the LrAu value is same with Gr Hug it doesn t need to compensation set 1 3 Check message The resolution is set to be exceeded the limit 1 50 000 Check the resolution The balance weight for span calibration is lower than 1096 or greater than 10096 of the maximum capacity of the scale The weight for span calibration should be within 10 100 of the maximum capacity of the scale Load cell output is too small or large at span calibration Check the weight unit and load cell or calibrate with lower resolution CRANE SCALE CCB SERIES 2 Wireless Pairing Step Operation amp Description How to enter the pairing mode 1 CCB crane scale When the display is off press ON OFF key while pressing key When E l Firmware version is displayed press KG LB key ALI Then c FSEE is displayed 2 CRD F wireless display Press the ON OFF key to power on and immediately press KG LB key And press the KG LB key again Then c FSEE is displayed 3 CRC 100 controller When the display is off press ON OFF key while pressing ENTER key When Firmware version is displayed press3 key Then c FSEE is displayed 4 CRC 200 wireless dongle Press the SET KEY for the 5 seconds with the power on that connected Then t
Download Pdf Manuals
Related Search