EverBrew Installation and Operating Instructions
Contents
1. power on Defective Control Board Temp Sensor not connected to Control Board Hot water temperature exceeds the Set Temperature Water inlet was open for longer than 15 20 minutes 9 Water continuously flowing Defective Inlet Valve from the spray head and will Defective Control Board not stop Defective Power Supply Board Test the incoming water supply pressure Water pressure should be between 30 and 80 psi If the water pressure exceeds 80 psi install a water pressure regulator and reduce the water pressure to 50 psi Call for service assistance Adjust the copper tubing so it does not touch the coffee appliance counter top or wall Test the incoming water supply pressure Water pressure should be between 30 and 80 psi If the water pressure exceeds 80 psi install a water pressure regulator and reduce the water pressure to 50 psi Call for service assistance Unplug the machine power cord from the wall outlet and re plug the machine power cord Machine should operate properly If the machine still fails to operate properly Call for service assistance Call for service assistance 10 Poor tasting coffee Water Water deposits are plugging the spray head or siphon deposits are plugging the tube spray head or siphon The brewing temperature has not been adjusted correctly tubing The amount of coffee being used may not be correct More than one paper filter was used when brewing The coffee appliance should2. limit thermostat Symptom Possible Causes 1 The coffee appliance will not The power supply cord is not plugged in turn ON when the power switch is turned ON No power at the wall outlet The hi limit thermostat has tripped The fuse is open 2 The coffee appliance trips Too many appliances are connected on one electrical the building s circuit breaker circuit The electrical circuits amperage rating is too low 3 The water for brewing is not The brewing temperature has not been adjusted correctly hot enough 4 The water for brewing is too The brewing temperature has not been adjusted correctly hot Insufficient incoming water flow Remedies Plug the power supply cord into an appropriate wall receptacle Test the wall receptacle and the circuit breaker in the building Call for service assistance Call for service assistance Remove any other coffee appliances from the current circuit or call an electrician to correct this problem Locate a correctly rated circuit or call an electrician to correct this problem Call for service assistance Call for service assistance 9 Incorrect or inconsistent The water supply pressure may not meet requirements beverage level 7 The coffee appliance is The water supply tube may be touching the coffee making unusual noises appliance counter top or walls The water pressure may be excessive 8 Service Light comes on at Defective Temp Sensor
3. 2pm PM time is set when the green dot is lit next to the PM in the upper left corner of the display box 3 To set minutes press and hold the minus button minutes will advance from 00 to 59 4 After setting the clock press the program button twice to exit from the menu NOTE This machine is preset at the factory for the following settings FACTORY PRESET SETTINGS Volume Settings Full Brew 64 oz 7 00 Minutes Half Brew 32 oz 3 30 Minutes Qtr Brew 16 oz 1 45 Minutes RESETTING THE VOLUME Amount of Coffee to be brewed NOTE When making volume adjustments always be sure an empty container with 64 ounces capacity is under the brew cone and the power is ON 1 Press and Hold the PROGRAM button approximately 3 seconds until the display changes and the set light flashes then press the PROGRAM button two 2 times The display window will now be blank Press the FULL BREW SELECTION button Note the display will start counting minutes and seconds and water will start to flow into the container When desired volume has been reached press the FULL SELECTION button to stop the water flow If more water is needed press the FULL SELECTION BUTTON repeatedly until desired level is reached After the SELECTION buttons is programmed press the PROGRAM button to exit the Program mode To program the HALF BREW SELECTION follow steps 1 amp 2 instructions above using the HALF BREW SE
4. Il EVERBREW Installation amp Operating Instructions EVERBREW Built In Coffee Appliance With Programmable Clock Timer and Lighted Display Model 1033518 WATER INC 800 322 WATER 9283 www waterinc com Instruction Number 9600202 Rev A 11 17 04 IMPORTANT INFORMATION amp SAFEGUARDS Read all instructions and safeguards included in the packaging carefully and completely before installing or operating this equipment Save all instructions for future reference To reduce the risk of fire or electric shock do not remove covers There are no user serviceable parts inside Repairs should be done by authorized service personnel only If this appliance should fail to operate properly contact Water Inc direct at 800 322 9283 Only Authorized Replacement Parts Should Be Used Part substitutions could create a fire hazard and the risk of personal injury The use of replacement parts or accessory attachments not recommended by Water Inc may be hazardous Be sure the carafe is empty and properly positioned beneath the brew cone Spilling hot water can scald The container is designed for use with this appliance IT MUST NEVER BE USED ON A RANGE TOP Unless specific instructions for use on a range top are provided and included the precautions are to be observed Do not set a hot container on a cold surface Do not use a cracked container or a container having a loose or weakened handle Do not clean container with cleanser
5. LECTION button After the SELECTION buttons is programmed press the PROGRAM button to exit the Program mode To program the QTR BREW SELECTION follow steps 1 amp 2 instructions above using the QTR BREW SELECTION button After the SELECTION buttons is programmed press the PROGRAM button to exit the Program mode Page 6 SETTING AUTOMATIC BREW TIME 1 Press and hold the PROGRAM button for 3 seconds the display will show 00 00 or the default brew time Note you have 30 seconds to begin entering the brew time To set hours press and hold the button hours on the display will advance from 00 to 12pm PM time is set when the green dot is lit next to the PM in the upper left corner of the display box To set minutes press and hold the minus button minutes will advance from 00 to 59 To set the volume option amount of coffee to be brewed press the button that corresponds to the amount desired full pot half pot quarter pot options The light will light when the button is selected After setting the brew time press the program button once to exit from the menu The display will show the current time and the light next to the volume selection button will be flashing Note The clock must be set in order to have Brew Start Time functioning To cancel the programmed Brew Time press and hold the PROGRAM button Release button when the time comes on Disp
6. be cleaned regularly 11 There are coffee grounds in Using too much coffee or coffee that has been ground too the brewed coffee fine Incorrect type of paper filter being used Two paper filters may have been used accidentally Clean the spray head See the Maintenance And Cleaning section Call for service assistance Change the amount of coffee being used Use only one paper filter for each brew cycle See the Maintenance And Cleaning section Adjust the amount of ground coffee being used or adjust the grind of the coffee Too much coffee or coffee that is ground too fine may slow the flow of the water through the coffee Make sure that the paper filter being used is correct for this type of coffee appliance Use only one paper filter per brew cycle If the steps in this trouble shooting guide should fail to solve your problem unplug the coffee appliance and contact Water Inc at 800 322 9283 This trouble shooting guide is for the installers use only Operator should refer to the operating instruction only Page 8 LIMITED WARRANTY The Factory warrants this product to be free of defects in material and workmanship for a period of one 1 year from the original date of purchase Within this warranty period Water Inc will repair or replace at its option any part providing it s defective in material or workmanship Labor is included within this warranty only during the first ninety 90 days of the warranty perio
7. bel Fig 6 applied over the FILL WATER TANK BY PRESSING DOWN i POWER FILL SWITCH UNTIL WATER operating switches on the front of the aa IE FILL machine and remove it after the check TURN ON POWER list is complete SWITCH LOCATED IN BACK Fig 6 OPERATING INSTRUCTIONS CAUTION Read these instructions completely before operating this coffee brewer CAUTION Make sure the installation instructions have been followed before attempting to operate this coffee brewer Incorrect installation or operating procedures will void the warranty and may cause damage to this coffee appliance Note Make sure the tank has been filled with water before the power switch is turned ON The temperature probe may be damaged and warranty will be voided if the power switch is turned ON before tank is filled with water See Filling The Water Tank PREPARING TO MAKE COFFEE 1 Place a paper coffee filter into the brew cone Add the desired amount of fresh ground coffee into the paper filter Note Individual coffee tastes vary greatly If you are not sure how much ground coffee you should be using add one level tablespoon of automatic drip coffee for each cup being made Increase or decrease this amount to suit your own coffee tastes Note To provide better extraction gently tap the side of the brew cone to level the bed of coffee in the brew cone 2 Place the brew cone with coffee and filter into the cone rails and gently push the brew cone all t
8. d This warranty excludes defects caused by negligence misuse alteration accident prior service by unauthorized persons and failure to follow the installation and operating instructions including without limitation use of improper voltage or wiring and improper cleaning This warranty applies only to new products and extends only to the original purchaser This warranty is valid only in the United States of America and its possessions IMPORTANT WARRANTY INFORMATION THANK YOU FOR PURCHASING THIS PRODUCT WE HOPE THAT YOU WILL ENJOY USING IT WE SUGGEST THAT YOU KEEP ALL THE PACKAGING AND OTHER MATERIALS FOR THE TIME BEING SHOULD YOU ENCOUNTER ANY PROBLEMS WITH YOUR PRODUCT DO NOT RETURN YOUR PRODUCT TO THE STORE AFTER REFERRING TO THE INSTRUCTION MANUAL IF YOU STILL NEED ASSISTANCE CALL OUR SERVICE DEPT AT 1 800 322 9283 EXT 32 OR 12 THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES FOR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THIS WARRANTY EXCLUDES CONSEQUENTIAL DAMAGES some states do not allow limitation or exclusion of implied warranties or consequential damages In such cases the limitations stated above may not apply to you and your rights will be determined by applicable law Page 9 ZVERBREW Water Inc 800 322 WATER 9283 www waterinc com
9. ect installation or operating procedures will void the warranty and may damage this coffee brewer Note Any changes to the internal plumbing or wiring of the building should be performed by a licensed plumber or a licensed electrician Check applicable building codes and requirements for procedures and restrictions that may apply during this installation This appliance is designed to be mounted to the underside of a kitchen wall cabinet near a convenient source of water and power MOUNTING See mounting Diagram Page 4 For Details 1 Check the contents of the package carefully In addition to the coffee brewer and these instructions the following items should be present If any item is missing contact Water Inc to arrange for a replacement Coffee Appliance Brewer Mounting Brackets and Screws Brew cone Installed on Coffee Brewer Flared nut Installed on water inlet fitting Filter Paper Page 3 MOUNTING DIAGRAM MOUNTING PLATE MOUNTING PLATE SCREWS WING NUT 9 a 4 MOUNTING SCREW 3 4 Fig 2 SET UP See Fig 2 TO INSTALL THE APPLIANCE PROPERLY FOLLOW DIRECTIONS BELOW AND FIGURE 2 ABOVE NOTE TO AVOID POSSIBLE DAMAGE TO THE CABINET MAKE SURE TO USE THE MOUNTING PLATE AS A TEMPLATE TO DRILL THE TWO 2 3 32 DIA PILOT HOLES a Determine the desired location of the appliance b Remove the brew cone from the appliance and remove the wing nut See Fig 2 lllust 3 from the lower mountin
10. ess steel decanter or thermos Release the power fill switch when a water starts flowing into the vessel See Fig 4 Pa 10 After the water has stopped flowing into the decanter remove the wing nut securing the safety screw across the power FILL fill switch and push the power fill switch to the ON up position See Fig 5 POSITION 11 Empty the vessel and replace under the cone 12 Press the full brew button setting 13 Test the temperature of the water as it comes out of the brew cone Maximum water temperature should be approximately between 192 F to 196 F Fig 4 14 See the Trouble Shooting guide for adjustment instructions if required The coffee appliance is now ready for use Refer to Operating Instructions for more details if needed If this coffee appliance should fail to function properly refer to the Trouble Shooting Guide for further instructions These Installation Instructions are for installers only Operators should refer to Operating Instructions only _ SAFETY SCREW Rb SAFETY S x BRACKET f NOTICE DO NOT REMOVE UNTIL THE FOLLOWING IS COMPLETED BEFORE BREWING ON INITIAL INSTALLATION THE FOLLOWING MUST BE DONE TO INSURE LONG LIFE AND TO PREVENT DAMMAGE TO YOUR NEW COFFEE APPLIANCE WATER SUPPLY CONNECTED AND secre 2 oN For a complete checking of the coffee Fia 5 CONNECT TO POWER AND BE CERTAIN I I id CONNECT TO POWER AND BE CERTAN maker installation please refer to the g la
11. g screw and slide the mounting plate out from the rear of the appliance c Loosen but do not remove the nut holding the L bracket to the rear of the mounting plate Holding the mounting plate in place flush along the bottom edge of the cabinet facing See Fig 2 Illust 1 drill two 2 3 32 Dia pilot holes on the cabinet using the 2 holes provided on the mounting plate flange to assure that the mounting screws will go in easily and not damage the cabinet d After drilling the two 2 pilot holes hold the mounting plate in place Fig 2 Illust 2 install two 2 screws through the holes provided at the front edge of the mounting plate and tighten This will mount the front of the mounting plate e While holding the mounting plate level hold mounting L bracket up against the bottom of the cabinet and mark the location of the rear mounting screw through the slot in the L bracket Drill a 3 32 pilot hole at the marking to assure that the mounting screw will go in easily and not damage the cabinet Install the mounting screw through L bracket at the location marked f Hold the mounting plate level tighten the nut to hold the rear of the mounting plate in place g Slide the appliance onto the mounting plate making sure the attachment screw on the rear of the appliance fits into the slot on the L bracket Attach the wing nut to hold the appliance in place Level the appliance and tighten the wing nut No
12. he way in until it stops 3 Place an empty 64 ounces 1 9L capacity glass or stainless steel decanter or thermos under the brew cone Page 5 MAKING COFFEE 4 Press the volume selection button that corresponds to the amount desired Full Pot Half Pot or Quarter Pot 9 In less than a minute fresh hot coffee will begin to flow from the brew cone into the decanter or thermos WARNING Hot coffee can cause serious burns Make sure that the coffee has stopped coming out of the brew cone before you remove it from the coffee appliance HANDLE HOT COFFEE CAREFULLY 6 After the brewing cycle is complete remove the brew cone and discard the used coffee grounds and paper filter Rinse the brew cone with water and place it back into the coffee appliance 7 To brew another decanter or thermos of coffee repeat instruction steps 1 thru 6 CAUTION Make sure decanter or thermos is empty of coffee before brewing again ADJUSTMENTS PROGRAMMING YOUR EVERBREW See Fig 7 SETTING THE CLOCK FULL BREW DISPLAY St IE WINDOW FULL BREW BUTTON HALF BREW POWER LIGHT BUTTON QTR BREW BUTTON HOURS SETS PROGRAM HALF QTRBREW MINUTES BUTTON BREW LED LED Fig 7 1 Press and hold the program button for 3 seconds the display will first show the brew time press once again and the display will show the clock time as indicated by the flashing colon 2 oset hours press and hold the plus button hours on display will advance from 00 to 1
13. imit Thermostat Manual reset Not adjustable Amps 13 6 Hertz 60 Phase 1 Power Supply Cord 4 Ft 2 Wire Ground Plug NEMA 5 15P Furnished and attached Power Supply Required 120Volts 15 Amp dedicated circuit Wall Receptacle Required 15Amp NEMA 5 15R Not furnished Listing ETL Electrical amp Sanitation Page 2 10 11 12 13 Button Press to adjust the clock hr and or adjust the time hr for Brew Start Time Button Press to adjust the time min and or adjust the time min for Brew Start Time Program Button Press this button to change the time and selection settings Power Light When lit indicates unit is in ON Quarter Brew Selection Light Will light when Quarter Brew selection is pressed or flash when selection is in program mode Quarter Brew Selection Button Press this button to select Quarter Brew selection to brew coffee Half Brew Selection Light Will light when Half Brew selection is pressed or flash when Half Brew selection is in Program Mode Half Brew Selection Button Press this button to select Half Brew selection to brew coffee Full Brew Selection Button Press this button to brew a full decanter Full Brew Selection Light Will light when Full Brew selection is pressed or flash when Full Brew selection is in Program Mode Service Light Indicates problem with the machine and service is required Display Window Displays the time
14. in hours minutes and program information Brew Cone Guide Rails Slide the brew cone in here INSTALLATION INSTRUCTIONS 14 15 16 17 18 19 20 21 22 23 24 25 CONTROL LOCATIONS AND DESCRIPTIONS REIT ET ee i TA a N P 4 Z SEE 2 u gt k t Toggle Switch On Off Fill Turns ON the power to the coffee appliance and fills the tank prior to use Fuse Holder Holds the fuse to the coffee appliance Power Supply Cord Connect this cord to appropriate wall receptacle Rear Mounting Bracket Holds the rear of the machine Flared Nut Fitting Insert this to copper tube before flaring Water Inlet Fitting The incoming water supply connects here LIGHT Dot Display PM Indicator When lit indicates time is past 12 O clock in afternoon LIGHT Dot Display Brew time SET Indicator Will light when a Brew time is Set Wing Nut Secures the machine to the L bracket Top Mounting Plate Secure this to the underneath the cabinet Safety Bracket Prevents the user from dry firing when the screw is in place during installation Safety Screw Prevent the toggle switch from being pushed up before filling the tank with water WARNING Read these installation instructions completely before connecting this coffee brewer to a power supply or water supply The water tank must be filled with water for this coffee brewer to function properly WARNING Incorr
15. lay will show the actual programmed brewing time press the flashing VOLUME SELECTION LIGHT button the light will turn off and same for the Set light Press the PROGRAM button again to exit the Program Mode To re program a different VOLUME SELECTION brew button option Press and hold PROGRAM button Release button after the display changes press a different VOLUME SELECTION brew button to change the existing programmed brew button The previous assigned VOLUME SELECTION brew light will turn off Press the PROGRAM button to save the change and to exit the Program Mode Note Brewing coffee while the Brew Start Time is set will cancel the current Brew Start Time repeat steps 1 through 5 to re program Note Brew Start Time is set for one brew cycle only This coffee maker will not automatically revert to the preset brew time This function must be re programmed each time WARNING Always make sure an empty container such as a glass decanter stainless steel decanter or thermos is placed directly beneath the coffee appliance brew cone when a Brew Start Time is set lf this coffee appliance should fail to function properly unplug it and contact Water Inc at 800 322 9283 MAINTENANCE amp CLEANING CAUTION Only those persons trained and qualified in equipment repair should attempt to CAUTION Turn the power switch off unplug the power supply cord and allow the coffee N
16. ote Do not use abrasive or harsh cleaners as they may damage the finish of this Note Failure to follow these cleaning instructions may damage this coffee appliance As needed clean stainless steel surfaces with a mild non abrasive stainless steel cleaner Other surfaces can be cleaned with a soft damp cloth or mild liquid detergent The brew cone should be rinsed with water after each brew cycle At least once a week the brew cone should be washed by hand with a mild detergent Rinse well after washing As necessary the area between the brew cone rails and above the brew cone should be wiped clean with a damp cloth as coffee oils will gradually collect on these surfaces Fig 8 Once a week more often in hard water areas the spray head located above the brew cone Should be removed and cleaned open and clean the inside of this coffee appliance appliance to cool before cleaning coffee appliance and may void the warranty Fig 9 Page TROUBLESHOOTING SERVICE SHOULD BE PERFORMED BY QUALIFIED SERVICE PERSONNEL ONLY WARNING Turn off the Power Fill toggle switch Unplug the power supply cord and allow the coffee appliance to cool before servicing unless electrical testing is required WARNING Make sure installation instructions have been followed before attempting to test this coffee appliance Note Allow the coffee appliance to heat up to brewing temperature BEFORE testing the temperature water volume or the hi
17. s steel wool pads or other abrasive material Do not touch hot surfaces Use handles or knobs whenever possible Do not let power cord hang over the edge of table counter or touch hot surfaces To reduce the risk of fire or electric shock do not mount unit over or near any portion of a heating or cooking appliance Do not place any electric or gas heating appliance beneath this unit Do not immerse in water or other liquids Do not mount over a sink Close supervision is necessary when any appliance is used by or near children Unplug from outlet and allow to cool before servicing or cleaning Do not use outdoors Do not use appliance for other than intended use Do Not By Pass Any Safety Mechanisms Or Operate This Appliance Without Covers In Place Water Inc requires that all safety devices and covers be in place and functioning at all times to guard against a fire hazard and the risk of personal injury Water Inc Does Not Recommend And Will Not Furnish Anyone With Information For Changing The Electrical Rating Of Any Appliance Distributed By Water Inc Water Inc will not approve of any unauthorized changes to the basic design of this appliance Any modification or alteration to the appliance may create a fire hazard may create a risk of personal injury may void the safety listings and may void the warranty All procedures diagrams and specifications contained in this manual are based on the latest information available at the time of p
18. sembled water line onto the water inlet fitting Fig 1 item 19 located on the rear of the appliance and tighten the water line To prevent damage to the appliance s water inlet fitting hold the inlet fitting with a wrench while tightening the water line Note The water filter will not fit behind the Everbrew The water filter should be installed to the water line underneath the counter 9 Turn on the water supply 6 Check for water leaks at the water inlet fitting Tighten the fitting if necessary ELECTRICAL CONNECTIONS Make sure the power switch Fig 1 Item 14 is in the off middle position before connecting the power supply cord to prevent damage to the machine Refer to Fig 4 on page 8 a Connect the power supply cord into the proper power supply as indicated on the electrical nameplate WARNING Be certain the power supply is of the correct rating and polarity before connecting the power supply cord Failure to heed this warning will void the warranty and may cause damage or injury FILLING THE WATER TANK SEE FILLING 7 Place the brew cone in the cone rails and push the cone all the way in pea A 8 Place an empty 64 ounce 1 9 Liter capacity glass stainless steel decanter or thermos under the brew cone OFF ta 9 To fill the water tank press down and hold the power fill switch located on the rear of the coffee appliance until water RL ose flows from the brew cone into the empty glass stainl
19. te Make sure the appliance is level If the appliance is not level loosen the top mounting nut and level the appliance Tighten nut PLUMBING CONNECTION See Fig 3 below for a typical water line connection Note This coffee brewer is designed to operate with water pressure of 30 to 80 psi If the water pressure exceeds 80 psi it is recommended that a water pressure regulator not included to be installed and reduce the water pressure to 50 psi Depending on water conditions in your area it is recommended that an in line water filter or other water filtering system not included be installed to improve the quality of the water It is recommended that a shut off valve not included be installed on the incoming water line to allow the water supply to be turned off for cleaning and servicing The shut off valve should be installed to the machine before any water filtering system that may be installed After installing the desired components onto the incoming water line flush the water line to remove any impurities that may be present in the line and to flush an inline water filter if installed If installed read the in line water filters manufacturers recommendations for correct flushing procedures 4 lt adi i Incoming a Be D water Supply Coffee ee In Line Water Filt n Line Water Filter Brewer To be under the counter Water Iniet Fitting Fig 3 Typical water line connection Page 4 4 Connect the as
20. ublication Information parts and Specifications are subject to change without notice Due to periodic reviews and changes in listing standards listings and approvals may change at any time For current listing and approval information contact Water Inc Plumbing connections All plumbing connections to water supply lines and drains should be performed by a licensed plumber complying with all applicable plumbing codes having jurisdiction Electrical connections With the exception of cords with plugs already attached all electrical connections or alterations to the power supply should be performed by a licensed electrician complying with all applicable electrical codes having jurisdiction When calling for information parts or service have the following information available Model Number SerialNumber 72727 Voltage Amps __ Phase __ Date Of Purchase Electrical information may be obtained from the electrical information nameplate located on the appliance SAVE THESE INSTRUCTIONS APPLIANCE INFORMATION APPLIANCE SPECIFICATIONS SETTINGS AND ADJUSTMENTS Model Numbers 1033518 Brewing Capacity 50 to 64 oz on Full Brew setting Descriptions Everbrew With Programmable Clock Timer Brewing Temperature Brewcone 192 F 89 C to 196 F 91 C and LIGHTED Display Dimensions 13 W x 3 9 16 H x 7 17 32 D Thermostat Adjustment See Service Manual For Adjustments Volts 120 Flow Control 065 GPM Flow Rate Watts 1600 Hi L
Download Pdf Manuals
Related Search