coinco global 2® 800 series operation and service manual
Contents
1. Replace acceptor Replace changer s main logic board Replace changer s main power harness Plug acceptor cable and or changer power hamess into changer main logic board Replace changer s main logic board Replace changer s main power harness Check power source Reposition changer and or vendor coin return lever Clean acceptor and remove any foreign matter Replace acceptor Replace changer s main logic board Replace defective acceptor Replace changer s main logic board Replace changer s main power harness Page 29 SECTION 5 TROUBLESHOOTING Troubleshooting Guide TROUBLE POSSIBLE CAUSE PROCEDURE REMEDY Accepted Coins Always Go To Cashbox Coin Routing Check that coins are routed to tubes See Rerouting the Coins Check the sensor board for loose components Make sure tube sensor board is properly secured to main logic board Check cable from sensor board for damage or improper connection Tube Sensor Board or Acceptor Replace tube sensor board If coin still goes to cashbox replace acceptor with good acceptor and test to see if changer functions properly Replace acceptor Accepted Coins Always Go To Coin Tubes Changer Credits Coins But Does Not Escrow No Payout Coin tube gate is in the open position Tube Sensor Board Coin return lever Acceptor Switch 9 is ON escrow is inhibited Payout Motor If coin still goes to cashbox Remo2. TABLE OF CONTENTS SECTION 1 GENERAL INFORMATION Introduction t SSSR 3 For Your Records ees ond awe his ests soca iad Soe Ue 3 I LETEN AU I a SAE NOE E T OE ANSE qoo i ede HIIS E BS 4 After Unpacking aS 4 SDECITCHBOBS sace erede cea et ute das 4 SECTION 2 INSTALLATION Installing th CMAN Set S ERES 5 Installation DIagratms esses 7 SECTION 3 CONFIGURATION Display ie ibo ioa e cen tla 9 Option Switch Module sceniniais glas Fer oes 10 Setting the Vend Price on a Single Price Changer 11 Setting the Vend Price on Four Price Changer 12 Setting the Vend Price on a Protocol A Changer 13 Setting the Cashless Vend Price on a Protocol A Changer 13 Setting the Vend Price on and BDV Changers 14 cL 14 Float Modes eoa rau ben redo TaN 14 Setting the Float Mode Levels ierat tte tenente 15 Activating Float Pay DOWt ue pee 15 Setting The Use Correct Change Value eter 16 Setting the Exact Change Accept Group 16 Reading Audit nene 18 Tube COUN lessen ih pete abr tut aciei iuis 18 Digital Display Address Chart eee 19 Changing Coin oiu ot oerte up
3. CONNECTOR CONNECTOR DISPLAY DATA LINK HARNESS PROTOCOL A CONNECTOR WITH STRAIN RELIEF CONNECTOR PROTOCOL A CONFIGURATION Page 36 800 Series 800 Series Harness and Logic Board Configuration PROTOCOL A 0 MDB HARNESS DEX MIS HARNESS 8 MDB MASTER HARNESS 9 MDB SLAVE HARNESS SINGLE FOUR PRICE HARNESS 407864 BILL VALIDATOR DEX MIS CONNECTOR HARNESS G MDB HARNESS 407544 LARGE PLUG DEX MIS HARNESS CONNECTOR G MDB HARNESS CONNECTOR F S CONFIGURATION 800 Series DISPLAY HARNESS DATA LINK HARNESS PROTOCOL A PROTOCOL A HARNESS PRIMARY TRANSFORMER CONNECTOR SINGLE FOUR PRICE HARNESS CONNECTOR BILL VALIDATOR CONNECTOR DISPLAY CONNECTOR SECONDARY TRANSFORMER CONNECTOR Page 37 CoIN ACCEPTORS INC PRODUCTS ARE PATENTED AND PATENTS ARE PENDING IN THE UNITED STATES AND THROUGHOUT THE WORLD Coin Acceptors Inc World Headquarters 300 Hunter Avenue St Louis MO 63124 2013 Phone 314 725 0100 Coin Acceptors Europe Ltd 4 The Felbridge Centre Imberhorne Lane East Grinstead W Sussex RH19 1XP England Phone 44 0 1342 315724 Email europe coinco com Website www coinco com Coinco Publication No 924242 Rev 4 01 2005 Printed in the U S A
4. 4 x Scaling Factor 8 x Scaling Factor 16 x Scaling Factor 32 x Scaling Factor 64 x Scaling Factor 128 xScaling Factor Switch 5 Switch 6 Switch 7 Switch 8 Figure 11 Example Switch 1 3 4 set to on and the remaining set to off would result in a price of 1 4 8 x Scaling Factor If the scaling factor were set to 5 and the decimal point set to 2 the resulting price setting would be 1 4 8 x 05 13 x 05 0 65 units The current scaling factor can be displayed using display mode address A010 on the acceptor The current decimal point position can be displayed using diplay mode address A011 NOTE The vend price must be set to an amount greater than zero for the changer to accept coins in single price mode VIA DIGITAL DISPLAY 1 Enter the Display Mode see Display Mode section of this manual 2 Press B to scroll up to C001 Price 1 3 Press C to enter The current Price Setting is displayed 4 Use buttons B increase and D decrease to change C001 to the appropriate price 5 Press A to store price and return to the Display Mode 7 Press A to exit the diplay mode Note The Display Mode will exit automatically if there is no programming action for 30 seconds Page 11 SECTION 3 CONFIGURATION Setting The Vend Price On A Four Price Changer The vend price on a four price changer may be set in four ways via Coinco Support Software via DEX UCS via the first eigh
5. Press B increase or D decrease to 1 to set standard float levels 2 for float pay down or 0 to disable float mode 6 Press C to enter your selection The far right decimal point will illuminate indicated the selection has been stored 7 Press A to return to the Address selection 8 Press A again to exit display mode All four tube float levels are now set d The Digital Display s second decimal point from the nght will be illuminated if any tube float levels have been set 800 Series Setting Float Levels Individually 1 Load the individual coin tube to the float level you want the coin changer to maintain 2 Enter the Display Mode see Display Mode section of this manual 3 Press B to scroll up to Address A008 for individual tube float setting 4 Press C to enter the Address 5 A will be displayed indicating tube Use button B increase or button D de crease to reach the desired tube selection 6 Press C to enter the Sub Address 7 Use button B increase to reach the correct setting O to disable 1 for standard float 2 for float pay down 8 Press C to store setting The far right deci mal point will illuminate indicating the selection has been stored 9 Press C again to return to the Sub Address Display 10 Press A to return to the Address Display 11 Press A again to exit the Display Mode The tube float level is now set for the indi
6. Tube Aand cashbox Coin Types 4 5 and 7 15 goto Cashbox only 800 Series SECTION 4 MAINTENANCE Routine Maintenance Routine maintenance will improve performance and extend the working life of your COINCO GLOBAL2 changer and reduce the need for more involved repairs Frequency of mainte nance will depend on environment and number of transactions For normal environments cleaning is recommended every six months However in harsh environments with lots of dirt and dust cleaning is recommended every three months The coin changer should be kept in its original shipping carton when not in use This will keep the changer clean and offer the best protection for the unit SS Lane Loge rg Coo Figure 12 800 Series Cleaning A majority of your COINCO GLOBAL2 changer is manufactured from a high quality plastic which should only be cleaned with a warm water and mild detergent solution CAUTION Never submerge unit in water Do not use petroleum solvents steel wool scouring pads or a metal brush for cleaning Do not spray any part of the changer with any type of lubricant Since all coins share a common coin ramp heavy usage or a dirty environment can result in ditt build up To clean the coin ramp lift the acceptor gate upward and diagonally to the right Hold gate to prevent it from snapping back Wipe the exposed coin ramp and inner surface with a damp cloth being cautious not to harm
7. and fifth price setting switches are in the UP position the vend price setting would be 25 x 1 or 25 assuming the lowest denomination coin accepted is 1 NOTE If the price for one or more of the selections is set to zero that selection is a free vend VIA DIGITAL DISPLAY 1 Enter the Display Mode see Display Mode section of this manual 2 Press B to scroll up to C001 Price 1 3 Press C to enter The current price setting is displayed 4 Use buttons B increase and D decrease to change C001 to the appropriate price 5 Press A to set the price and return to the Display Mode 6 Press B to increase to the next priceline E g Address C002 Priceline 2 7 Repeat steps 3 6 for the remaining three prices 8 Once all four prices have been set press A twice to exit the Display Mode 800 Series SECTION 3 CONFIGURATION Setting The Vend Price On A Protocol A Changer The vend price on a Protocol A changer may be set in three ways via Coinco Support Software via DEX UCS via the digital display SETTING THE STANDARD PRICELINES If the vending machine operates in Price Hold ing Mode then the twenty five prices are set using Addresses C101 C125 accordingly 1 Enter the Display Mode see Display Mode section of this manual 2 Press B to scroll up to Address C101 For Priceline 1 3 Press C to enter The current price setting is displayed 4 Use buttons B increase and D decre
8. ed edu uis 23 Changing Coin Routing iiie Co tr eere gren Seed eom esee eig 23 SECTION 4 MAINTENANCE Routine Marmtenance eodd Qe E a d 25 GV RIND Saeco e 25 Removing Replacing Individual ModuleS 0 0 26 Cleanng Coin Jams oo ee aka ace 26 SECTION 5 TROUBLESHOOTING Error Ole tL M ER AE 27 Di gnostieS P 28 Troubleshooting Guide 29 SECTION 6 EXPLODED VIEWS Exploded asser 31 SECTION 1 GENERAL INFORMATION Introduction This manual contains information on installing operating and maintaining your COINCO GLOBAL2 coin changer The manual is intended for owners route operators and shop level technicians as a primary source of information Taking time to read this manual and becoming familiar with this information will help you obtain the best performance from your COINCO GLOBAL2 changer The COINCO GLOBAL2 Changer from Coin Acceptors can accept and validate up to 32 different coins or tokens The COINCO GLOBAL2 Changer has the ability to be dual currency using a built in exchange rate convertor It is programmable through a digital display making it easy to set up a user configuration The COINCO GLOBAL2 Changer is compatible with current vending machine protocol standards as follows MDB For electronic vending machines that utilizes COI
9. is unable to make change for the programmed value or any lesser value Page 10 800 Series SECTION 3 CONFIGURATION Setting The Vend Price On A Single Price Changer The vend price on a single price changer may be set in four ways via Coinco Support Software via DEX UCS via the first eight Option Switches via the digital display The vend price can be set in single increments up to 255 times the lowest denomination coin that is accepted by the changer and routed to a coin tube EXAMPLE If the lowest denomination coin is one the highest vend price setting would be 255 xl or 255 VIA COINCO SUPPORT SOFTWARE Consult Coinco Support Software manual for price setting instructions VIA DEX UCS Consult Hand held Computer manufacturer VIA OPTION SWITCHES Note The switches are ON in the upwards position 1 Set the vend price by adding the amount of the appropriate switches and setting them to the ON position see Figure 11 2 Set Option Switch B to the OFF position 3 Set Option Switches A C and D to the desired configuration see Option Switch Module section of this manual 4 After setting the vend price and the desired options press and release the Mode Button to store the new setting The LED and the Use Correct Change light will then flash once indicating that the price was recorded 800 Series Switch 1 Switch 2 Switch 3 Switch 4 1 x Scaling Factor 2 x Scaling Factor
10. reuse if you need to trans port or ship your changer in the future If the coin changer is being stored or used as a spare always keep it in its shipping carton when not in use This will keep it clean and offer the best protection for the unit Page 4 Specifications Power Requirements by model s dieci MOS 34V DC Single Four Price 24V AC 50 60 Hz 120V AC 50 60 Hz 220V 240V AC 50 60 Hz Protocol 24V AC 50 60 Hz SS esit Te 24V DC 24V DC Operating Temperature Non Metric Metric 0 to 150 Degrees Fahrenheit 18 to 65 Degrees Celsius Storage Temperature Non Metric Metric 22 to 160 Degrees Fahrenheit 30 to 72 Degrees Celsius Relative Humidity 20 to 98 Noncondensing Operating Attitude Vertical 3 degrees Physical Dimensions Metric Non Metric Height BASE TO TOP OF COIN RETURN LEVER 379 2mm 14 93 inches 138 9mm 5 47 inches GATE OPEN 82 5mm 3 25 inches GATE CLOSED 76 2mm 3 00 inches Width Depth Weightin Shipping Carton Non Metric Metric Approximately 7 pounds Approximately 3 15 kilograms Coin Size Range Up to 32 coins or tokens in the size range of 15 0 to 33 5 mm diameter and 1 02 to 3 10 mm thickness can be validated 800 Series SECTION 2 INSTALLATION Installing The Changer Main Logic 1 Remove power from the vending machine Board LED 2 Remove the acceptor from the changer by OT ae Mo
11. Acceptor Assembly ITEM NO DESCRIPTION Mainplate and Coil Operating Lever Spring Operating Lever Retaining Ring Gate Lever Pivot Screw Gate and Coil Assembly Gate Board Keypad Gate Cover Label Front Cover Intermediate Cover Label Mirror 575 Debounce Validation Debounce Sorting Hand Loading Door Hand Loading Door Spring Accept Reject Door Sort Door Cashbox Door CO C UB WN r2 NR PP OAD I 21 Pivot Diverter Pin 22 Short Diverter Pin 23 Coin Stop 24 Plunger and Yoke Assembly 25 Tube C and Plunger Assembly 26 Copper Plated Spring 27 Solenoid Coil Assembly 28 C Frame Solenoid 29 Tube B and Plunger Assembly 30 Spring Retention Plug 31 Self Locking Hex Nut 32 Logic Board 33 Rear Cover 34 Acceptor Label 35 Debounce Plate 36 Patent Label 37 Foam not shown 38 Foam not shown 39 Screw Pan Head 4x5 16 40 Global Decal 41 Anti Stringing Lever 42 Screw Flat Head 4x5 16 43 Acceptor Gasket 44 Insert Mainplate selective models only 45 Screw Flat Head 2x3 16 selective models only 46 Gate Board assembly for service only 800 Series Page 35 SECTION 6 EXPLODED VIEWS 800 Series Harness and Logic Board Configuration G MDB HARNESS 407544 SMALL PLUG LARGE PLUG 2 REQ D Q8 G CONNECTOR DEX HARNESS CONNECTOR PROTOCOL A HARNESS MDB HARNESS WITH STRAIN RELIEF
12. C026 C027 C028 Uu C042 C043 C044 C045 C046 C047 C050 C051 C052 C053 Y lt 800 Series Page 21 SECTION 3 CONFIGURATION DIGITAL DISPLAY GENERAL USE ACCEPTOR INFORMATION ADDRESSES Addresses Select Unit Configuration 1 Enables and pays out coins 16 31 applicable to Dual Currency 2 Enables coins 0 31 pays out coins 16 31 models only 3 Enables coins 0 31 pays out coins 0 15 4 Enables and pays out coins 0 15 Note The reported currency will be that of the coins being paid out A002 Payout Configuration Used to select a standard payout configuration or for ere M RE a user payout configuration ALT options are user programmable A003 Tokens Enabled If tokens Meee oc tz Disable all tokens are 1 1 Enable all A004 Coin Ratio read only Displays the coin values A005 Coin ate 0 Coin is disabled 1 Dummy MDB coin 2 Coin accepted Non compressed for MDB 3 Coin accepted Compressed for MDB The following can only be set in the factory 4 Slug Eater 5 Slug Eater with dummy coin 6 Credited and Returned Non compressed 7 Credited and Returned Compressed A006 Validation Acceptance Level Relative acceptance Levels 1 10 for all 32 coin types 1 Highest slug protection 7 Factory acceptance rate 10 Highest acceptance rate A007 Float Setting All Tubes Each Digit Represents a Tube A B C D 0 Float mode disabled 1 Float
13. Electromechanical A Protocol A Executive BDV Note All models have MDB in addition to the primary protocol XXX The first digit of the model number indicates the series of the changer 7 8 or 9 The last two digits indicates the changers payout configuration Z Indicates any special options Page 3 SECTION 1 GENERAL INFORMATION Features The COINCO GLOBAL 2 coin changer has a modular design for easy service Tubes snap in and out of housing for easy customization of your changer Pays out change from self loading high capacity change tubes Two motors provide fast accurate payout Programmable tube floats allow variable tube level adjustment State of the art electronic logic system is designed for reliability and performance Lightweight rugged plastic construction All models equipped with the MDB proto col Lockable coin loading door allows easy hand loading of coin tubes while keeping dirt and debris out of the changer The Protocol A Executive changer has the ability to be an MDB master to a either Bill validator or cashless system After Unpacking After unpacking the unit inspect it for any possible shipping damage If the unit is dam aged notify the shipping company immediately Only the consignee the person or company receiving the unit can file a claim against the carrier for shipping damage We recommend that you keep the original shipping carton and packing materials to
14. NCO s Multi Drop Bus technology Note All Global changers are equipped with the MDB interface as standard Single Price Four Price For electromechanical vending machines Protocol A Executive For vending machines equipped with an electronic Protocol A serial interface Protocol A Executive with MDB Master As above with the additional ability to interface to MDB Bill validator or MDB Cashless devices whilst being connected to a vending machine in protocol A mode e BDV For vending machines equipped with an electronic BDV serial interface 800 Series For Your Records A label indicating the coin changer model number and serial number can be found on the side of the coin changer Refer to the model and serial number whenever you call upon your Coinco Service Centre for information or service For your information the first four digits of the serial number indicates when the unit was built which is also the beginning of the warranty period The first two digits indicate the week of manufacture the third and fourth digits indicate the year of manufacture For example Serial Number 1503005895 would indicate that the unit was manufactured in the 15th week of 2003 The changer model number is shown in the following format AAA BXXXZ Where AAA The country currency code E g SEK Swedish Krone GBP Great Britain Pound B The primary protocol of the changer G MDB only F Four Single price
15. SPLAY Protocol A Power Connector VEND MOTORS 800 Series Page 7 SECTION 2 INSTALLATION Figure 7 Protocol A Executive Interface with MDB Master Support POWER SUPPLY P2 Protocol A EXECUTIVE CON SELECTION Data Connector Master TX MDB CASHLESS peers charcoal VENDING MACHINE MasterReceive Pee 3 DEVICE OR BILL CONTROLLER ACCEPTOR 2 Supply Gnd DIGITAL 2 3 P1 Protocol A A ENE Power Connector P3 MDB Master Connector Hb MOTORS Figure 8 Four Price Electro Mechanical Interface Exact Change Vend Line 1 E EXECUTIVE COIN Vend Line 2 CHANGER Vend Line 3 B Vend Motor E G GBP F811 Vend Line 4 2 1 2 Ne ieee 4 Typical Vending machine vend line wiring Only to be used as an example P1 Jones Plug Page 8 800 Series SECTION 3 CONFIGURATION Display Mode The 800 Series changer is equipped with a four digit seven segment display located on the acceptor gate The Display Mode is utilized via the four Inventory Buttons also located on the acceptor gate see Figure 9 This Display Mode is used to read information as well as to set different options including price settings and tube float levels The Display Mode may be entered by pressing Inventory Buttons A and D simultaneously In response the display will turn on the message FILL FULL or AbCd Button activa tion will be recognized only if lon
16. ards D011 Total vends for price 1 Count of vends for price 1 D012 Total vends for price 2 Count of vends for price 2 D013 Total vends for price 3 Count of vends for price 3 D014 Total vends for price 4 Count of vends for price 4 D015 Total vends for price 5 Count of vends for price 5 D016 Total vends for price 6 Count of vends for price 6 D017 Total vends for price 7 Count of vends for price 7 D018 Total vends for price 8 Count of vends for price 8 D019 Total vends for price 9 Count of vends for price 9 D020 Total vends for price 10 Count of vends for price 10 a 6 D029 Total value coins tube 4 Total value of coins in highest value tube Value sales from prepaid period D032 Value card discount life Value discounts during prepaid card use 800 Series Page 19 SECTION 3 CONFIGURATION Y Supported DIGITAL DISPLAY N Not Supported AUDIT INFORMATION CHANGER ADDRESSES R Read Only C001 Prices 1 Repeated at address C101 C002 Prices 2 Repeated at address C102 C003 Prices 3 Repeated at address C103 Prices 3 Repeated at address C103 lt Prices 8 Repeated at address C108 C009 Prices 9 Repeated at address C109 C010 Prices 10 Repeated at address C110 Multivend mode Discount award Increase in credit Value when discount trigger is reached C013 Discount Award Trigger C014 Exact ee eS Accept Group Single Four Price Electrome
17. ase to change the value to the desired price 5 Press A to store price and return to the Display Mode 6 Press B to increase to the next priceline E g Address C102 Priceline 2 7 Repeat steps 3 6 for the remaining priceline addresses 8 Once all twenty five prices have been set press A to exit the Display Mode SETTING THE NUMBER OF ACTIVE PRICELINES C055 If the vending machine operates in Price Hold ing Mode then the number of price lines avail able that are recorded in audit can be set using address C055 1 Enter the Display Mode see Display Mode section of this manual 2 Press B to scroll up to C055 Press C to enter Address C055 4 Use buttons B increase and D decrease to change the number of price lines in Address C055 59 800 Series 5 Press to store the value and return to the Display Mode 6 Press A to exit the Display Mode ENABLING CASHLESS PRICELINES C053 If the vending machine operates in Price Hold ing Mode address C053 is used to enable the Cashless pricelines C201 to C225 1 Enter the Display Mode see Display Mode section of this manual 2 Press B to scroll up to Address C053 3 Press C to enter C053 4 Use buttons B increase or D decrease to change the value 0 Enable price lines 1 Disable price lines 5 Press A to store the value and return to the Display Mode 6 Press A to exit the Display Mode SETTING THE CASHLESS PRICELINES If th
18. chanical Displays MDB coin type number Coins up to and including this value will be accepted when there is an Exact Change condition Executive Protocol A Coin Value reported Coins up to and including this value will be accepted when there is an Exact Change condition C015 Single M ultivend and Single Four Price Electromechanical Cashless Revaluation 0 Multi Vend Disabled 1 Multi Vend Enabled Executive Protocol A Card Revaluation OFF 0 Single vend Credit Limit 1 Multi Vend Credit Limit 2 Single Vend Price Limit 3 Multi Vend Price Limit Card Revaluation ON 4 Single vend Credit Limit 5 Mulit Vend Credit Limit es Vend Price Limit ulit Vend Price Limit C016 Escrow Return Inhibit i CUR Return Allowed 1 Coin Return NOT Allowed C019 Peripheral and Clear Checksum Flag No Executive Card Reader 0 Checksum OK 1 Checksum Error Executive Card Reader Installed 4 1 OK C020 Bill Value scaled Ner ee ne coni Programmable 4 20 seconds pn Y nw j Nj Page 20 800 Series SECTION 3 CONFIGURATION Y Supported DIGITAL DISPLAY N Not Supported AUDIT INFORMATION CHANGER ADDRESSES R Read Only L Mode Enabled 0 L Mode 1L Mode L Programmed Left tube coin L Programmed Right tube coin L Programmed Middle tube coin 0 15 Coins 0 12 Full Buffer Mode L Fourth Tube Reporting 0 Cashbox sorting always reported C029 Card Scale factor C030 Max Credit C032 Use Correct Chang
19. ctivating Float Pay down section of this manual When in Manual Fill Mode the acceptor will route coins to the tube until float level is reached When float level is reached the display will change to FULL and coins will be re jected The float pay down level does not change The changer will automatically return to operating mode after 45 seconds of no activ ity or if button A escape is pressed 800 Series SECTION 3 CONFIGURATION Setting The Float Mode Levels The Float Mode Levels for both Float Level and Float Pay down can be set in two ways e via Support Software via the Digital Display VIA COINCO SUPPORT SOFTWARE Consult Coinco Support Software manual for tube float level setting instructions VIA DIGITAL DISPLAY The Digital Display Inventory Buttons are located on the acceptor gate Address 007 allows you to clear all float levels and to set all four float levels at one time The individual tube float levels are set using Address A008 Setting All Four Float Levels At Once 1 Load the four coin tubes to the float level you want the coin changer to maintain 2 Enter the Display Mode see Display Mode section of this manual Press B to scroll up to Address A007 4 Press C to enter Address 007 display will show the current float mode settings for all tubes The far left digit represents tube A through the far right digit representing tube D 5
20. de Button releasing acceptor latch and rotating the top of the acceptor forward away from changer Option see Figures 1 and 2 Unplug ribbon cable Cable Switches from changer Free acceptor studs from changer housing Place the acceptor in a Acceptor clean area Stud 3 With the acceptor removed set the mounting holes in the back of the changer housing over the mounting screws in the vending machine Tighten securely see Figure 3 Do not over tighten as this could damage the changer housing 4 Replace the acceptor by inserting bottom acceptor studs into changer housing guides Figure 2 Plug the ribbon cable into the changer see Figure 2 5 On units that use a DEX UCS Hand held Computer attach DEX Plug Ground Connector to the vending machine frame 6 Connect the appropriate interface harness to the vending machine See typical setup Acceptor oh examples for the protocol being used Figure 5 for MDB Figure 6 for Protocol Executive Figure 7 for Protocol Executive with MDB master Figure 8 for 4 Price Electromechanical 7 Set the desired vend price and options on the changer Refer to Section 3 Configuration Note The vend prices are set on the vending machine controller when operating in MDB mode or Protocol non price Figure 1 holding 800 Series Page 5 SECTION 2 INSTALLATION 10 Check to make sure the tube cover and acceptor studs are properly insta
21. e The payout configuration has been changed to 802 EXAMPLE The COINCO GLOBAL changer is configuredasfollows Coin Type 0 goes Tube Coin Type 1 goes to Tube B Coin Type 2 goes to Tube C Coin Type 3 goes to Tube D Remaining Coin Types 4 15 goto Cashbox BUT Coin 6is interchangeable with coin type must be accepted to Tube A along with coin type 0 Page 24 Example of setting up user defined coin routing Enter the Display Mode 2 Press B to scroll up to Address A002 3 Press C to enter the Address 4 Press B increase or D decrease to choose one of the programmable payout configura tion selections Press C to select the payout configuration 6 Press C again to enter programmable payout configuration mode The display will be shifted to the far left 7 Use button B and D to choose tube A on the display then drop one of coin type 0 and one of coin type 6 8 Select tube B drop one of coin type 1 9 Select tube C and drop one of coin type 2 10 Finally Select tube D drop one of coin type 3 11 Verify all coins have been routed to the desired tubes 12 Press A to return to address menu 13 Press A again to exit The payout configura tion has now been changed to Coin Type 0 goes to Tube Aand cashbox Coin Type 1 goes to Tube Band cashbox Coin Type 2 goes to Tube Cand cashbox Coin 3 goes to Tube D and cashbox Coin Type 6 goes to
22. e all coins previously routed to the tube with different values will be rejected If value is chosen for a new destination the coin type dropped will have its routing changed to the cashbox Press ing enter button C again will return to the second sub address menu esc button A will always return to the high level address selection menu For correct operation the scaling factor should be equal to the value of the least coin accepted E g if the least value coin accepted is the GBP 10p after altering the payout configuration the scaling factor in address A010 should be changed to 10 Float modes will be turned off and coin counts will be cleared for any tube in which all coins assigned to the tube were not previously as signed to the tube and have been assigned during the current payout configuration session Page 23 SECTION 3 CONFIGURATION Example of changing the predefined coin routings To configure the coin tubes via the Digital Display follow these steps 1 Enter the Display Mode see Display Mode section of this manual 2 Press B to scroll up to the Address A002 3 Press C to enter the Address 4 Use buttons B increase or D decrease to change selection to 802 5 Press C to enter the new routing information The far right decimal point will illuminate to indicate the selection has been stored 6 Press A to return to the Address Display 7 Press A to exit the Display Mod
23. e value C036 Price Hold and Display 0 Disable Price Holding 2 Enable Price Holding 3 Enable Price Holding and Price Displa Price Display Mode 0 Disable 1 Enable Keep Change Mode 0 Disable nadie Four Price or Single Price Mode 0 Single Price Mode 1 Four Price Mode Single Price Vend Mode 0 Pulse Vend 1 Vend Holding Until Blocker Signal Alternate Exact Change Mode 0 Programmed Value 1 Use Highest Price Plus Highest Coin 1 Mode Switch Disabled Addresses C001 through C255 1 Changes From Digital Display Disabled C049 Enable DEX Clear 0 DEX Clear Disabled 1 DEX Clear Enabled DEX Clear 0 DEX datais present 1 Clear DEX audit data MDB Bill Acceptor Exact Change Notes are Accepted up to and Including This Accept Group Value MDB Bill Acceptor Escrow 0 Bill Escrow Enabled 1 Bill Escrow Disabled MDB Cashless Price Lines 0 Enabled Disabled C054 MDB Cashless Response Dela C055 umber of Active Price lines C056 Executive Audit Peripheral Device 0 Disabled Enable 1 Enabled Interim 2 Enabled Total 3 Enabled Interim and Total C060 C067 1D101 DEX Audit Field Machine Identification Number C074 C089 Token Values Values Assigned To Any Tokens Accepted C Protocol A Price lines 25 Price Lines The Prices Lines are used when N in Price Holding mode for coin credit 101 C125 C201 C225 Cashless Price Lines 25 Cashless Price Lines The Prices Lines are used when a vend is carried out using credit Address C022 C024 C025
24. e bottom of the coin tubes Shims are re moved and replaced by sliding in or out of the bottom of the coin tube NOTE Do not reuse shims Installation and removal can stress the plastic causing the shims to lose their ability to stay firmly in place CHANGING THE COIN ROUTING After changing the coin tubes the coin routing needs to be reconfigured via the Digital Display using Address A002 This address allows the user to change payout configuration in the field This feature only provides a means for the acceptor to alter coin routing when different physical payout tubes have been placed in the changer body 800 Series When address A002 is entered five payout configurations are available Selection is achieved by scrolling up button B or down button D to the desired configuration When the desired setting is reached press enter but ton C to store the selection The far right decimal point will illuminate to indicate the setting has been stored to memory If the location has the capability of being program mable Display shows Altl for example press ing enter button C again will enter program mable mode This will be evident if a value between and e is displayed To program a coin to a tube select the tube by scrolling to the desired tube a is the first tube on the left and drop the coin type to be routed to the tube If a coin s value differs from the coins currently routed to the tub
25. e is too small and the remainder system is disabled Rejected as the coin set associated with this coin is not enabled Figure 15 800 Series SECTION 5 TROUBLESHOOTING Troubleshooting Guide TROUBLE POSSIBLE CAUSE PROCEDURE REMEDY No coin acceptance No Coin Acceptance or Rejects Percentage of Good Coins Accepts Coins But Gives No Or Erratic Credit 800 Series No power Acceptor Low Power Vend price is set to 0 Coin Return Lever Acceptor is dirty or foreign matter in coin accept path Acceptor Make sure changer is plugged into vendor Check power blocker LED behind acceptor Four Price Only If LED is on replace acceptor If still no coin acceptance If still no coin acceptance If LED is off check to see that acceptor cable and changer power harness are properly connected to changer s main logic board If still no coin acceptance If still no coin acceptance Flashes 20 on display when coin is dropped Set vend price see Setting the Vend Price sections of this manual Make sure changer is mounted correctly and coin return lever is in proper position Check to see that acceptor coin path is clean and free of matter If still rejects good coins If still rejects good coins Replace acceptor with good acceptor and test to see if changer functions properly If still no erratic credit If still no erratic credit Plug changer into into vendor
26. e vending machine operates in Price Hold ing Mode the cashless pricelines are set using Addresses C201 C225 When a vend is made using credit from an MDB Cashless device the prices stored in these addresses will be used Cash vends will still use the prices stored in addresses C101 to C125 1 Enter the Display Mode see Display Mode section of this manual 2 Press B to scroll up to C201 Press C to enter Address C201 4 Use buttons B increase and D decrease to change the value to the desired price 5 Press A to store the price and return to the Display Mode 6 Press B to increase to the next priceline E g Address C202 Cashless priceline 2 7 Repeat steps 3 6 for the remaining pricelines 8 Once all twenty five prices have been set press A to exit the Display Mode 95 13 SECTION 3 CONFIGURATION Setting The Vend Price on MDB amp BDV Changers Vend prices for MDB BDV changers are set through the vending machine controller VMO See vending machine manual for details Manual Fill Mode Manual Fill Mode allows coins to be inserted into the acceptor which routes the coins to the proper coin tube without establishing credit When high sensor level or float level is reached and in manual fill mode coins will be rejected Enter the Display Mode see Display Mode section of this manual When FILL appears in the display deposit coins until the desired level Alternating wit
27. ger than 0 5 seconds Once you have entered the Display Mode Inventory Buttons A through D are used to move through the addresses as follows BUSTA 5 Button 2 22 21 INCREASE Buttons C un etes ENTER Button D eese DECREASE EXAMPLE Simultaneously press A and D to enter Display Mode Press B to increase scroll through the various addresses Once you have reached the address you need to access press Button C to enter the address Information currently stored in non volatile memory will be displayed with the far right decimal point illuminated Use either Inventory Buttons B or D to increase or decrease the address values as needed Press Button C again to store the selection Press A to return to the Address Display Press A again to exit the Display Mode You will exit the Display Mode if one of the following procedures is performed 1 No Inventory Buttons are pressed or coins are dropped for more than 45 seconds 2 Depressing the A Button until the Display Mode is exited 3 Automatic exit after hardware reset 800 Series 800 Series Changer DIGITAL DISPLAY Figure 9 DIGITAL DISPLAY Normal Operating State Indicates Power is ON Indicates Float Level Is Set On At Least One Tube Indicates At Least One Coin Is Enabled Indicates By A Flash Each Changer Acceptor Communication Figure 10 NOTE All addresses in the Display M
28. h the FILL message will be the tubes needing coins AbCd The changer will automatically return to operating mode after 45 seconds of no activity or if button A escape is pressed Manual Fill Mode is supported for Single Four Price Protocol A and BDV changers Manual Fill Mode in MDB changers is accessed through the vending machine con troller See vending machine manual for details Page 14 FloatMode Float Mode is used to systematically reduce the number of coins kept in a tube The 800 Series GLOBAL2 changer supports two Float Mode Options which are set through the use of Coinco Support Software or the digital display STANDARD LEVEL FLOAT MODE In Standard Float Level Mode once a tube float level is set see Setting The Float Mode Lev els section the changer will try to maintain the set level of coins in the tube by routing accepted coins to the tube only if a coin was paid out Once the tube reaches its float level in Standard Float Mode any coins normally routed to that tube will be sent to the cashbox As usual any cashbox coins will be accepted and routed to the cashbox FLOAT PAY DOWN MODE In Float Pay down Mode the acceptor will continue to route coins to the tube until the upper sensor is covered The coins will then be routed to the cashbox Once a tube float level is set activating Float Pay down will dispense coins above the established levels until the coins reach the float levels see A
29. is retrieved via the Digital Display by performing the following steps 1 Enter the Display Mode see Display Mode section of this manual 2 Press C In response the display will show Address 4000 3 Press B or D to scroll to the desired audit address see Audit Information Addresses 4 Press C to view the upper four digits of the displayed address Press C again to view the lower four digits including the decimal point if any EXAMPLE 10 480 20 would be displayed as 0104 in the upper four digits followed by 80 20 in the lower four digits 5 Press C again to return to the Address Display 6 Press A to exit to the FULL FILL AbCd message NOTE Audit Information is read only it can only be reset using Coinco Support software or if address C049 is enabled Use address C050 to clear audit data NOTE Free vends issued directly from the vending machine are not audited by the changer Page 18 Tube Counts By briefly depressing and releasing an inventory button you can obtain information about the coin value and the quantity of coins within the tube 800 Series SECTION 3 CONFIGURATION DIGITAL DISPLAY nem AUDIT INFORMATION ADDRESSES N Not Supported E ICM ON 002 003 D004 Inventoried cas Total value dispensed using eeu i inventory buttons D005 D006 vend value exact change light is on D008 D009 Value of vends from tokens D010 Prepaid card value Value taken from prepaid c
30. level set 2 Float pay down set A008 Float Setting Individual Tubes 0 Float mode disabled 2 Float pay down set 1 Enable Enhanced coin payout A010 Scaling Factor Value used to scale all coins A011 Decimal Point Value read onl Remainder Enable 0 Remainder disabled Applicable to Dual Currency 1 Remainder enabled never cleared models only 2 Remainder enabled cleared at reset 3 Remainder enabled cleared at payout 4 Remainder enabled cleared at reset or payout Indicates asub address is used Page 22 800 Series SECTION 3 CONFIGURATION Changing The Coin Tubes and Coin Routing REMOVING REPLACING THE TUBES To remove the coin tubes remove the acceptor and then remove the grey smoked front cover by pulling out on the left side of the cover at the notch in the housing The front cover will swing forward exposing the tubes The tubes can be removed one at a time by pulling up ward Four slots have been placed in the front of the changer along the pay out assembly area to assist in this procedure Place a screw driver into the slot and apply an inward pressure to free the tube retainer tab whilst pulling upwards on the tube Replace the coin tubes by inserting the dove tail guides into the tube holes and pushing inward and downward ABOUT THE SHIMS The coin tubes in your COINCO GLOBAL2 changer utilise six interchangeable shims to accommodate variable thicknesses of coins These shims are color coded and are fixed to th
31. lled Mounting 11 Test the coin changer with a variety of coins to ensure proper operation Inventory Buttons Coin Tube x Loading Door Figure 3 8 Press the top of the acceptor into the changer housing until the acceptor latches and locks 9 If coin tube loading door is not locked Figure 4 additional option hand load the four coin tubes see Figure 4 Tilting the coin tube loading door open load the four coin tubes Make sure all coins lie flat and that each tube is filled at least to the 20 mark Payout at least two coins from each tube to set tube counters Note Hand loading the tubes will not give an accurate audit reading If audit is required the tubes should be loaded in Fill mode see relevant section of this manual for further details Page 6 800 Series SECTION 2 INSTALLATION Figure 5 MDB Interface POWER SUPPLY pes MDB EM Devices E g Key reader Bill validator Audit device etc sar sagen Audit device etc s SWITCHES VENDING MACHINE CONTROLLER MDB MASTER Baers DIGITAL P1 MDB Slave as Connector MDB Slave Peripheral Master TX y CHANGER Comms Gnd 6 5 Supply Gnd 2 MOTORS Figure 6 Protocol A Executive Interface POWER SUPPLY 24 VAC xw ae n EXECUTIVE COIN CHANGER E G GBP A801C TX VENDING MACHINE CONTROLLER RX TX 6 SHIELD DIGITAL DI
32. ly Housing Assembly Payout Assembly Acceptor Assembly Transformer F S models only Logic Board Board Upper Tube Sense Cover Logic Board Lens Upper Tube Sense Lens Cashbox Latch PVC Foam Bracket Strain Relief Screw Pan Head 6 x 11 16 Screw Pan Head 6 x 1 2 Label Identification Label Patent ITEM NO 17 18 19 DESCRIPTION Harness Bill Validator optional selective models Label Configuration Screw Flat Head 4 x 5 16 Tube Inventory Shim Mirror Tube A Mirror Tube C and D Labels Tube Front Cover Coin Retum Plug Lg Strain Relief selective models Plug Sm Strain Relief selective models Label Price Setting F S models only Label Warranty selective models Screw Pan Head 4 x 3 4 Pad selective models 800 Series SECTION 6 EXPLODED VIEWS 800 Series Payout Base Assembly ITEM NO DESCRIPTION 1 Removed Tube Home Sense Board Lower 3 Gear Encoder 4 Cover Gearbox 5 Base Payout Upper 6 Base Payout Lower 7 Assembly Motor Harness 8 Assembly Sweeper 14 Lens Tube Sense Lower 9 Arm Coin Clearing 15 Gear Reduction 10 Gear Reduction 16 Harness Lower Tube Sense 11 Gear Pinion 17 Washer Plastic selected models only 12 Shaft Gear 18 Screw 8x1 2 PH PHL Threadcutting 13 Cable Tie 19 Retainer Motor 800 Series Page 33 EXPLODED VIEWS SECTION 6 800 Series Acceptor Assembly 800 Series Page 34 SECTION 6 EXPLODED VIEWS 800 Series
33. n the left side of the cover at the notch in the housing The front cover will swing forward exposing the tubes Remove the four inventory tubes one at a time by pulling upward Remove strain relief bracket which is located in the upper left corner of changer housing by remov ing screw Remove recessed screw that secures logic board cover and remove cover Push snap toward top of housing and remove upper tube sense board which will separate from main logic board upon removal PAYOUT BASE Disconnect the two motor harnesses and the tube sense harness Remove the screws from the bottom exterior sides of the changer housing and remove payout base MAIN LOGIC BOARD ASSEMBLY Unplug harnesses from logic board and lift the logic board out of the housing Page 26 Clearing Coin J ams Should a coin jam occur in the cashbox chute area use the following steps to help dislodge coins 1 Remove changer from vendor 2 Keeping changer in an upright position remove cashbox chute located on the back of the changer by pulling lower edge out and down at the same time 3 Remove any lodged coins 4 Replace the cashbox chute by pressing in and up to snap into place 800 Series SECTION 5 TROUBLESHOOTING Error Codes If any of the errors listed below as 001 007 are detected the message Eror will flash on the display To view the error or a list of errors enter the Display Mode see Display Mode section of
34. ode can be made Read Only disabled via Coinco Support Software see separate Coinco Support software manual for further information NOTE If power is removed from the changer before the Display Mode is exited the changes may not be saved Page 9 SECTION 3 CONFIGURATION Option Switch Module Single Price Four Price Models Only Located behind the acceptor on the middle right hand side of the changer housing are twelve switches see Figure 2 The first eight are used to set the vend price see Setting The Vend Price section of this manual The last four Option Switches are used to enable or disable the following options Note The swiches are ON in the upwards position Switch A SW9 Controls whether the escrow feature of the changer is inhibited Escrow inhibited OFF Escrow not inhibited Switch SW10 Determines the operation mode of the changer ON Operates as a Four Price changer OFF Operates as a Single Price changer Switch C SW11 Single Price Mode Only Controls the vend holding feature ON Vend is held until selection is made OFF Vend is pulsed Switch D SW12 Controls when the changer enters the Use Correct Change condition ON Uses the sum of the highest price plus the value of the highest coin for the Use Correct Change indicator OFF Uses a programmable value for Use Correct Change indicator Use Correct Change indicator is illuminated when changer
35. opped both the decimals points Fig ure 13 and the four digits Figures 14 and 15 are used to communicate various diagnostic conditions as shown DIGITAL DISPLAY DECIMALS When Coin Return Lever Is Depressed Indicates Power Is ON Indicates Float Level Set On At Least One Tube Indicates Right Cashbox Sensor Is Blocked Indicates Left Cashbox Sensor Is Blocked Figure 13 DIGITAL DISPLAY DIGITS When Coin Return Lever Is Depressed TUBEA TUBE B TUBE TUBE D The Following Values In The Above Tube Positions Indicate the Condition in the Corresponding Tube No Sensors Are Blocked Lower Sensor Is Blocked Lower and Upper Sensors Are Blocked Tube Is J ammed Sensor Error Figure 14 Page 28 DIGITAL DISPLAY DIGITS When Coin Is Inserted The Following Values In The Following Positions Indicate a Response to the Coin that was J ust S the digit 2 is used for example purposes Coin Type Not Recognized Note One of the following letter codes may appear in lieu of the C An attempt has been made to route however the coin was not sensed at the credit allocation sensors Rejected as controller has disabled acceptance of the MDB coin type associated with this coin or error in routing due to cashbox sensor being blocked Rejected as coin has been disabled by the acceptors internal coin enable settings Rejected as the coins value is too large to enable coin s acceptance or the valu
36. rrect Change Setting Press C to enter the Address 4 Use button B increase or button D decrease to reach the correct value 5 Press C to store setting Press A to return to the Address Display 7 Press A again to exit the Display Mode The Exact Change Setting is now programmed to the value you have set 2 D Page 16 Setting The Exact Change Accept Group Single Four Price and Protocol A Models Only By setting the Exact Change Group you are telling the changer what coins to accept when the Use Correct Change light is ON When the light is OFF all enabled coins in the coin set are accepted The Exact Change Group can be programmed in three ways via Coinco Support Software via DEX UCS via the Digital Display VIA COINCO SUPPORT SOFTWARE Consult Coinco Support Software manual for Use Correct Change light setting instructions VIA DEX UCS Consult Hand held Computer manufacturer VIA DIGITAL DISPLAY The Exact Change Group is set using Address C014 of the Digital Display 1 Enter the Display Mode see Display Mode section of this manual 2 Press B to scroll up to Address 014 3 Press C to enter the Address 4 Use button B increase or button D decrease to reach the coin value or Exact Change group to be accepted 5 Press A to return to the Address Display 6 Press A to exit the Display Mode The Exact Change coin value group is now pro grammed to the
37. t Option Switches via the digital display The vend price can be set in single increments up to 255 times the lowest denomination coin that is accepted by the changer and routed to a coin tube EXAMPLE If the lowest denomination coin is one the highest vend price setting would be 255 xl or 255 VIA COINCO SUPPORT SOFTWARE Consult Coinco Support Software manual for price setting instructions VIA DEX UCS Consult Hand held Computer manufacturer VIA OPTION SWITCHES Note The swiches are ON in the upwards position 1 To set the vend price of a selection add the value of the rocker switches that are switched to the ON position see Figure 11 2 Set Option Switch B to the ON position 3 Set Option Switches A C and D to the desired configuration see Option Switch Module section of this manual 4 After setting the desired vend price on the Option Switch Module press and release the Mode Button see Figure 2 The changer s Main Logic Board LED and the Use Cor rect Change light will begin to flash Page 12 5 Within 30 seconds press and release any one desired product selection switch on the front of the machine The present price on the switch module is now set for all selections on that price line and the LED and Use Correct Change light will stop flashing 6 Repeat the above steps until the remaining three price lines have been assigned a vend price EXAMPLE If the first fourth
38. the coin stabilizer a thin piece of polyester film If the coin stabilizer looks buckled wrinkled or is not firmly adhered to the changer replace it at this time NOTE Not all COINCO GLOBAL2 changers are equipped with a coin stabilizer For detailed cleaning of the acceptor remove the front cover by opening the coin tube loading door and wedging thumb undemeath front cover To remove cover push out and up Next remove the intermediate cover by depressing snap on right side and pivot intermediate cover away from unit You are now able to fully clean both the intermediate cover paying particular attention to the mirrored surface as well as the interior coin rail and gates Use caution when removing the metal debouncer Due to its small size it can be easily misplaced Reassemble front of acceptor in reverse order of disassembly Page 25 SECTION 4 MAINTENANCE Removing Replacing Individual Modules Modular assembly replacement provides the basis of all COINCO GLOBAL2 series changer repair Instructions for removing and replacing modules are provided below These modules should be removed in the following sequence ACCEPTOR To remove the acceptor from the changer release the acceptor latch and pull the top of the acceptor forward away from the changer Unplug ribbon cable from changer Free lower acceptor studs from changer housing UPPER TUBE SENSE BOARD Remove the grey smoked front cover by pulling out o
39. this manual If a single error is detected the code will be displayed in place of the Full Fill AbCd message If there is more than one error the codes will alternate one after the other FULL FIEL AbCd No Errors PON Validation Sensors Error AEQ Tube Sensors Error M Coin Jammed EOUAT ou et ale Payout Error HOOD ROM Error bites Configuration Error E ost eds UU Supply Voltage Error The error codes listed below are displayed upon occurrence E DU Double Arrival nat coins dropped too fast SB A Payout sweeper arm is at the end of stroke re align the sweeper arm EZS VMC attempting to pay out oct coins from an empty tube The following errors will require the changer to be sent to a Coinco service centre for repair BST A to D Conversion fault tu necs c RE Validation Opto Fault T or jammed coin in validation path TE 257 85 E267 s EC coil reading timeout E27 amp 28 coil reading timeout EB DO ca essit Stored air values corrupt BLUR cess ta TAU coil failure uri EC coil failure or rc UR MF coil failure E IOs Acceptor memory failure 800 Series Page 27 SECTION 5 TROUBLESHOOTING Diagnostics When the coin return lever is depressed or a coin is dr
40. value you have set 800 Series SECTION 3 CONFIGURATION FOUR PRICE EXACT CHANGE GROUP SETTINGS Address C014 Accepts only coin number 0 Tes Accepts coin numbers 0 through 1 2 iuis Accepts coin numbers 0 through 2 Doo Accepts coin numbers 0 through 3 d cs Accepts coin numbers 0 through 4 Accepts coin numbers 0 through 5 OR Accepts coin numbers 0 through 6 Accepts coin numbers 0 through 7 B regius Accepts coin numbers 0 through 8 D edes Accepts coin numbers 0 through 9 10 Accepts coin numbers 0 through 10 11 Accepts coin numbers 0 through 11 12 Accepts coin numbers 0 through 12 13 Accepts coin numbers 0 through 13 14 Accepts coin numbers 0 through 14 15 Accepts all coins Note Coins of the same value are reported as the same coin number Coin Number 0 is the first coin value accepted coins that are disabled are not reported E g In the EUR A901 the Ic and 2c are disabled therefore the first coin accepted is the 5c so this is coin number 0 PROTOCOL A EXACT CHANGE GROUP SETTINGS C014 will list all coins accepted Select the coin value all coins up to and including this value will be accepted when the exact change light is ON 800 Series Page 17 SECTION 3 CONFIGURATION Reading Audit Information Single Four Price and Protocol A Models Only By reading Audit Information you can gain valuable information about your vendor s performance Audit information
41. ve acceptor back cover and check solenoid for free operation Replace tube sensor board with good board and test to see if changer functions properly If coins still go to tubes Make sure changer is mounted correctly and acceptor gate opens when vendor coin retum lever is operated Replace acceptor with good acceptor and test to see if changer operates correctly Uninhibit the escrow feature Make sure motor wires are properly connected to changer s main logic board If still no payout replace motor Replace changer s main logic board ace acceptor Replace tube sensor board Replace changer s main logic board Reposition changer and or vendor coin return lever Replace defective acceptor Turn switch 9 OFF and press the Mode Switch Plug motor wires into logic board Replace defective with good motor and test to see if changer operates properly payout motor Page 30 800 Series SECTION 6 EXPLODED VIEWS 58 4 800 Series Dimensional View mE ALL MEASUREM ENTS ARE SHOWN IN MILLIM ETERS 9 138 9 66 5 7 61 5 ml 2 1 gt TI j OFENDE 2 77727 7 Jj EM pl EN 4 8 3X 6 4 3X 9 7 ye RETURN 10 4 COIN PAYOUT CASHBOX 40 1 CHUTEAREA 800 Series Page 31 SECTION 6 EXPLODED VIEWS ITEM NO CO Un 4 W NF Page 32 800 Series Final Assembly DESCRIPTION Assemb
42. vidual tube you have chosen The Digital Display s second decimal from the right will be illuminated if any tube float levels have been set Activating Float Pay Down Pressing and releasing buttons A and B simulta neously activates Float Pay down Use Manual Fill to replenish low tubes see Manual Fill Mode section of this manual Page 15 SECTION 3 CONFIGURATION Setting The Use Correct Change Value Single Four Price and Protocol A Models Only When a value is selected for turning on the Use Correct Change light the light is illuminated when the changer is unable to make change for THAT value or any lesser value NOTE Option switch D set to the ON position will override any setting you make via the following instructions See Option Switch Module section of this manual for information on Option Switch D The Use Correct Change light can be pro grammed to come on in three ways via Coinco Support Software via DEX UCS Protocol A Only via the Digital Display VIA COINCO SUPPORT SOFTWARE Consult Coinco Support Software manual for Use Correct Change light setting instructions VIA DEX UCS Consult Hand held Computer manufacturer VIA DIGITAL DISPLAY The Use Correct Change light is set using Address C032 of the Digital Display 1 Enter the Display Mode see Display Mode section of this manual 2 Press B to scroll up to Address C032 Use Co
Download Pdf Manuals
Related Search