LIGHT DIMMER DIM
Contents
1. is left to the discretion of ZAMEL ver 0 4 2 _ 2006 06 20_11 002. and use of the device influence its wrong functioning It is not advisab le to instal the device in the following cases if any device part is missing or the device is damaged or deformed In case of improper functioning of the de Zaktad Mechaniki i Elektroniki ZAMEL spjj J W Dzida K todzinska ul Zielona 27 43 200 Pszczyna Poland Tel 48 32 210 46 65 Fax 48 32 210 80 04 www zamel pl e mail marketing zamel pl TECHNICAL PARAMETERS DIM 10 Input supply terminals Input rated voltage Input voltage tolerance Nominal frequency Rated power consumption Supply voltage control indicator Release terminals Lighting control Output load terminals Output switch on indicator Charging power Controlling element L N 230 V from 15 to 10 50 60 Hz 41 mA LED green IN IN IN unipolar connector N 7 LED red from 30 to 400 W triak 400 VA Number of terminal clamps Section of connecting cables Ambient temperature range Operating position Mounting Protection degree Protective class Overvoltage category Pollution degree Rated impulse withstand voltage Dimensions height width depth Weight 11 from 0 2 to 2 50 mm from 20 to 45 C free rail TH35 PN EN 60715 IP20 PN EN 60529 Il Il 2 1 kV PN EN 61000 4 5 doublemodule 35 mm 90x35x66 mm 125g Reference standards PN EN 60669 1 PN EN 60669 2 1 PN EN 61000 4 2 3
3. 4 5 6 11 APPEARANCE S Input supply terminals L Input supply terminals N Relay system terminals IN IN IN L Supply voltage vice contact the producer J indicator Input supply terminals N N N 2 amp 2 amp 2 amp XX Output load switch on indicator ver 0 4 2 _ 2006 06 20_11 00 Disconnect the power supply from the mains by the phase fuse the circuit breaker or the switch discon nector that are joined to the proper circuit lt L Check if there is no voltage on me connection cables by means of a ED Gee special measure equipment lt gt Install ASM 10 device in the N switchboard on TH 35 DIN rail Connect the cables with the termi nals according to installing diagram Switch on the power supply from the mains The system is used to control the lighting with a total power that does not exceed 400 VA The unipolar but ton is responsible for the control The buttons connected in a parallel way enable lighting operating from different places Short pressing and releasing the button for about 0 8 s causes the lighting switch over in the switch on off sequence Short pressing of the button causes the bulb switches on with full power if they are switched off the next short pressing causes a total switch off Holding the button for a longer time gt 0 8 s causes smooth alternate illumi
4. LIGHT DIMMER DIM 10 INSTRUCTION MANUAL DESCRIPTION The device DIM 10 is used to con trol the bulb lighting level The unipolar button is responsible for the control The buttons connected in a parallel way enable lighting operating from different places The system has the control switch on off function and smooth brig htening dimming the light The system enables intelligent lighting system con trol and gives comfort and economy in A Intelligent lighting control bulb lighting level control input rated indicator output load switch on indicator cooperation with unipolar pushbut tons equipped with neon light maximum power load 400 VA doublemodule casing TH 35 DIN rail installation Sooo y gt The device is desig ned for one phase in stallation and must be installed in accordance with standards valid in CAUTION a particular country The device should be connected according to the details in cluded in this operating manual Instal lation connection and control should be carried out by a qualified electrician staff who act in accordance with the service manual and the device fun ctions Disassembling of the device is equal with a loss of guarantee and can cause electric shock Before installation make sure the connection cables are not under voltage The cruciform head screwdriver 3 5 mm should be used to instal the device Improper transport storage
5. nating dimming After the input voltage and the lighting is switched off the adju sted level is not remembered A A PRODUCT FAMILY DIM 10 light dimmer belongs to Dix light dimmers DIX xx Type 10 Basic Casing type M_double module Typical application The lighting dimmer system controls the lighting in a room by means of unipolar pushbuttons installed on the walls AN A GUARANTEE CARD There is 24 months guarantee on the product N 1 ZAMEL provides a two year warranty for its products C The ZAMEL warranty does not cover a mechanical defects resulting from transport loading unloading or other circumstances b defects resulting from incorrect installation or operation of ZAMEL products c defects resulting from any changes made by CUSTOMERS or third parties to products sold or equipment necessary for the correct operation of products sold d defects resulting from force majeure or other aleatory events for which ZAMEL is not liable 3 All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect 4 ZAMEL will review complaints in accordance with existing regulations C Salesman stamp and signature date of sale_ 5 The way a complaint is settled e g replacement of the product repair or refund
Download Pdf Manuals
Related Search