OPERATION & SERVICE MANUAL F2000 CUTTING SYSTEM
Contents
1. expenses including reasonable attorney fees and expenses and other losses of any kind whatsoever whether based upon theories of contract tort negligence strict liability warranty indemnification contribution statute or otherwise for personal injury or property damage caused by BUYER or by any of its directors officers agents employees or subcontractors arising out of or relating to the Equipment Buyer shall give GLASSLINE prompt written notice of any such matters and the full opportunity to defend itself against them This indemnity of BUYER shall survive the termination of this agreement E The remedies and limitations set forth in this agreement are the exclusive remedies for claims based upon any defect in or failure of EQUIPMENT whether products or services whether such claims are presented in contract or in tort including negligence and however and wherever instituted Upon the expiration of the warranty period all such liability shall terminate 7 ORDER ACCEPTANCE GLASSLINE reserves the right to refuse any order An order shall be deemed accepted and a binding contract formed when the initial payment has been received and the order is acknowledged in writing by GLASSLINE 8 CANCELLATION BY BUYER BUYER may cancel the order for all or any EQUIPMENT by written notice prior to shipment GLASSLINE will stop work on the order as soon as possible after receipt of written cancellation BUYER agrees to pay GLASSLINE for all costs incurr2. shall be governed by the laws of the State of Ohio If any provision or term of this agreement is held to be invalid void or unenforceable the remaining provisions and terms of the agreement shall remain in force and effect and shall in no way be affected impaired or invalidated thereby In all cases the rights and duties of the parties in a dispute arising out of this transaction shall be governed by the laws of the State of Ohio H The delegation or assignment by BUYER of any or all of its duties or rights under this agreement without the prior written consent of GLASSLINE shall be void I Any information suggestions or ideas transmitted by BUYER or GLASSLINE or any of their respective representatives in connection with the performance under this agreement are not to be regarded as secret or submitted in confidence except as may be otherwise provided specifically in a document signed by a duly authorized representative of GLASSLINE J This agreement supersedes all previous agreements written or verbal and contains the entire agreement between the parties 2 TERMS AND CONDITIONS OF BUYER Should BUYER have standard terms of acceptance that it wishes to make a part of this agreement such terms must be provided at the time a quotation is requested and agreed to in writing by GLASSLINE so that the costs of compliance to such terms as GLASSLINE may agree if any may be added to the bid GLASSLINE reserves the right to quote these compliance
3. If the machine does not rotate in the correct direction swap the connections to wires 1 amp 2 of the incoming power Figure 2 Cycling the machine Rotation Arrow Figure 3 Rotation Direction DESCRIPTION OF CONTROLS AND ADJUSTMENTS POWER SWITCH The machine is equipped with a main power switch disconnect It is located on the control box at the rear ofthe machine Turn the power switch to the ON 1 position to apply power to the machine RUN BUTTONS The machine is equipped with two green push buttons to operate the machine They are located on each side at the front ofthe machine Both buttons must be pushed simultaneously for the machine to cycle REVERSING SWITCH The machine is equipped with a reversing switch on one side of the control box If placed in the reverse position the machine may be bumped in the reverse direction to allow the operator to back out if there is any problem CONVEYOR SWITCH The machine is equipped with a two position switch on the side of the control box The switch controls the operation of the conveyor In the left hand position the conveyor pulses on momentarily after each cutting cycle In the right hand position the conveyor runs continuously CONVEYOR CONNECTOR The machine is equipped with a connector plug near the conveyor switch The connector from the conveyor plugs into this location OPERATING INSTRUCTIONS OPERATION Make sure that all fasteners are tight Manually
4. created by GLASSLINE shall remain property of GLASSLINE 5 WARRANTY A GLASSLINE warrants against defects in material and workmanship Items manufactured by others but installed in or affixed to GLASSLINE EQUIPMENT are not warranted by GLASSLINE but bear only such express warranties if any of the manufacturer thereof GLASSLINE shall replace or repair at its choosing ex works GLASSLINE Perrysburg Ohio plant any defective manufactured parts without charge to BUYER The warranty does not apply to any labor charges for removal and or replacement or to any part thereof which has a life under normal usage inherently shorter than the warranty period The warranty will be active for a period of 1 Machinery 12 months from date of shipping 2 Replacement Repaired parts 6 months from date of shipping B Warranty shall be deemed waived by BUYER if 1 The EQUIPMENT is not properly installed by BUYER according to GLASSLINE installation instructions 2 The EQUIPMENT has been subjected to misapplication or misuse neglect damaging conditions or is modified in any way without written approval by GLASSLINE 3 The production or use of the EQUIPMENT for which it was not intended or on products out of specification C The warranty set forth herein is in lieu of all other warranties whether express implied or statutory including those of merchantability and fitness of any product for a particular purpose and of any other obligation or lia
5. features separately and above their standard quotation 3 DELIVERY AND CLAIMS A The quoted shipment schedule is non binding The shipment schedule will be set at time of order and is contingent upon BUYER supplying a clear scope of supply all technical information and any required downpayment A new delivery date may be required depending on any technical or scope changes requested after the order date or delays in receiving payments according to agreed dates B GLASSLINE shall not be liable for delays in delivery caused by any reason beyond GLASSLINE s control including but not limited to force majeure supplier failure any interruption of GLASSLINE facilities or any act of any government or licensing authority C Unless otherwise noted in the quotation all shipments are ex works GLASSLINE Perrysburg Ohio plant BUYER bears all risks of loss or damage to the EQUIPMENT from the time the EQUIPMENT has been placed at the disposal of Buyer at GLASSLINE whether shipping is arranged by BUYER or on behalf of BUYER by GLASSLINE In any case shipments shall be made strictly according to Incoterms 2000 D After the EQUIPMENT is placed at the required transfer point for BUYER GLASSLINE neither assumes responsibility for nor authorizes any expenses including electrical work plumbing compressed air supply millwright work extensions additions or materials necessary for the set up and operation of the EQUIPMENT in BUYER s plant or elsewhe
6. move the ram through a cycle to insure that all blades are properly aligned Turn the main power switch to the on position Place the tomatoes on the slicing blades Simultaneously push both green buttons Hold them until the cycle is complete As the ram completes its cycle it will stop to allow the machine to be reloaded CONVEYOR REVERSING CONTROL RESET 5 72 t MAIN POWER DISCONNECT Figure 4 External Controls Figure 5 Product Placement Figure 6 Operating the Push Buttons MAINTENANCE CLEANING Remove power from the slicer before cleaning The ram may be manually moved to insure proper cleaning Figure 7 Blade Notch Figure 8 Removal Figure 9 Internal Components Spare parts Machine F2007 Hinge bearing F2008 Plastic rollers F2009 Bearing F2010 Shaft seals F2011 Motor Conveyor F2999A Conveyor belt F2999B Motor F2999C Gears F2999D Belt roller F2999E Drive belt F2999F Bearing F2999G Shaft seals Blades F2000 Grid Sticks F2004 4mm Slicing blades and pusher F2005 5mm Slicing blade amp pusher F2006 6mm Slicing blade set F2608P Individual pusher finger F2822 8 segment wedging blade w 22mm core F2825 8 segment wedging blade w 25mm core F2830 8 segment wedging blade w 30mm core Misc F299
7. 8 Core separator Glassline Corporation 28905 Glenwood Road P O Box 147 Perrysburg OH 43552 0147 Phone 419 666 5942 Fax 419 666 1549 www glasslinecompanies com GENERAL TERMS AND CONDITIONS OF SALE This agreement sets forth general terms and conditions of sale The quotation and sales contract may incorporate additional and more specific commercial and technical requirements of sale The following general terms and conditions are mutually agreed between BUYER and GLASSLINE to be a part ofthe sales and purchase order documents 1 DEFINITIONS AND GENERAL TERMS AND CONDITIONS A The term GLASSLINE shall refer to Glassline Corporation and all of its affiliated divisions B The term EQUIPMENT shall refer to any machine part product or service sold by GLASSLINE including subcontracted purchased items options C The term BUYER shall refer to the buying company and where applicable its subcontractors D The terms and conditions set forth in this agreement are effective at the receipt of order by BUYER and are subject to change by GLASSLINE without notice before receipt of order by Buyer E Quotations are valid for 30 days unless noted otherwise F No terms conditions understandings usage of trade dealings or agreements purporting to vary modify explain or supplement this agreement shall be binding unless and until hereinafter made in writing and signed by BUYER and GLASSLINE G This agreement and its interpretation
8. OPERATION amp SERVICE MANUAL F2000 CUTTING SYSTEM NSEP SCOPE OF MANUAL THIS MANUAL IS FOR THE F2000 SLICER SLICER TABLE OF CONTENTS PREPARATION FOR USE AND INSTALLATION INSTRUCTIONS FIGURE 1 POWER CONNECTIONS u a FIGURE 2 CYCLING THE MACHINE 000 FIGURE 3 ROTATION DIRECTION ee DESCRIPTION OF CONTROLS AND ADJUSTMENTS eee eects OPERATING INSTRUCTIONS ae FIGURE 4 EXTERNAL CONTROLS sisas FIGURES PRODUCT PLACEMENT dia FIGURE 6 OPERATING THE PUSH BUTTONS MATNEENANGE u ea Ma Ver 2 0 6 04 o PREPARATION FOR USE AND INSTALLATION INSTRUCTIONS Examine exterior of machine for any sign of damage Ifany damage is observed note on bill of lading 1 Scratches dents or other damage 2 Broken shipping container Remove outer shipping material Carefully remove machine from crate and move to desired location Attach the conveyor to the machine Insert the connector from the conveyor into the connector on the side of the control box Connect 220V power to the attached power cord Figure 1 Power Connections Connect ground to the green yellow wire Connect incoming power to wires 1 2 amp 3 in the power cord Figure 1 Apply power to the machine Cycle the machine by pushing the green buttons Figure 2 Verify that the machine rotates in the correct direction Figure 3
9. bility on GLASSLINE s part of any kind or nature whatsoever D The warranty granted herein is non transferable and is granted only to the original BUYER E No employee agent or other representative has any authority to waive alter vary or add to the terms hereof without prior approval in writing signed by an officer of GLASSLINE 6 LIMITATION OF LIABILITY A It is expressly understood that GLASSLINE s liability for any damages arising out of or related to this transaction or for its EQUIPMENT whether in contract or in tort is limited to the repair or replacement of the parts thereof as stipulated in the warranty and is not to exceed the contract price in respect to which the claim is made B BUYER is solely responsible for ensuring the safety of all personnel who may be in close proximity to the EQUIPMENT C GLASSLINE will not be liable for any other injury loss damage or expense whether direct incidental or consequential including but not limited to labor loss of use downtime loss of material products income profit or production or increased cost of operation or spoilage of damage to material arising in connection with the sale installation use of or inability to use or the repair or replacement of or late delivery of GLASSLINE EQUIPMENT D BUYER shall indemnify defend and hold harmless GLASSLINE and its directors officers agents and employees against any and all demands claims actions damages liabilities costs
10. ed by GLASSLINE and or other suppliers attributed to the order including but not limited to components work in process labor burden and overhead Such payment will not transfer title to BUYER 9 ARBITRATION AGREEMENT Any controversy or claim arising out of or relating to this agreement or the breach thereof shall be settled by arbitration in accordance with the rules of the American Arbitration Association and the statutes of the State of Ohio All hearings held in connection with any such arbitration shall be held in Toledo Ohio unless the parties agree otherwise in writing the award of the arbitrator s shall be final and binding upon the parties and the judgment upon and the award rendered by the arbitrator s may be entered in any court having jurisdiction thereof 14 Acrobat Document Acrobat Document Acrobat Document Acrobat Document Acrobat Document 15
11. re It remains the BUYER s responsibility to meet all federal state and local codes and regulations E Claims for shipping damage concealed or otherwise are the responsibility of BUYER and should be taken up with the delivering carrier within the stated time allowed for claims Claims for shipping shortages will not be allowed unless reported to GLASSLINE within 10 days of shipment 4 TITLE A Title to the EQUIPMENT thus delivered shall remain with GLASSLINE until the full purchase price has been received 13 B BUYER shall keep the EQUIPMENT fully insured with GLASSLINE named as loss payee until the purchase price is paid Neither BUYER nor GLASSLINE shall assign the applicable insurance contact without prior written consent of the other C Monthly interest at the rate of 1 1 2 per month on the total unpaid value ofthe EQUIPMENT will be charged if delivery is delayed at BUYER s request for more than thirty 30 days after buy off or if final payment is delayed beyond thirty days 30 after shipment BUYER shall execute and deliver to GLASSLINE such documents and financial statements as may be necessary to perfect the lien or security interest of GLASSLINE to protect the unpaid balance of the purchase price D All tools materials software programs designs or any technology created for the purpose of producing the EQUIPMENT are the sole property of GLASSLINE unless furnished by BUYER with the order All intellectual property
Download Pdf Manuals
Related Search