Pull My Finger Service Manual
Contents
1. Your Friends at Gay Tek Games GAME INSPECTION Inspect the game for any damaged loose or missing parts If damage is found please contact your freight carrier first Then contact Bay Tek Games Service Department at 920 822 3951 or e mail them at service baytekgames com for further assistance 4 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 SPECIFICATIONS POWER REQUIREMENTS SHIP WEIGHT 755 lbs INPUT VOLTAGE RANGE 110 to 120 VAC 220 to 240 VAC INPUT FREQUENCY RANGE WEIGHT 675 Ibs WIDTH 49 DEPTH 32 1 4 MAX START UP OPERATING HEIGHT 91 CURRENT CURRENT OPERATING TEMPERATURE 1 6 AMPS 115 VAC 1 3 AMPS 115 VAC 80 100 Degrees Fahrenheit 0 8 AMPS 230 VAC 65 AMPS 230 VAC 26 7 37 8 Degrees Celsius SAFETY PRECAUTIONS DO NOT perform repairs or maintenance on this game with the power ON Unplug the unit from the wall outlet or shut off the power at the power strip located inside the game cabinet Use of flammable substances can cause severe burns or serious injury Always use NON FLAMMABLE solvents for cleaning DO NOT use gasoline kerosene or thinners Lifting heavy objects can cause back neck or other injuries Be sure adequate lifting and moving devices are available when unloading unpacking and moving this game Be sure the electrical power matches the game requiremen2. A related component such as a solenoid is causing an overload See Jumper Ca ble Pin Outs in manual to see which component might be at fault Green LED Light That cable is OK comes ON To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BILL ACCEPTOR DIAGNOSTICS Note There are many different models and brands of Bill Acceptors that are used on redemption games Your Bill Acceptor may differ from the unit shown First determine if Bill Acceptor has power Turn game ON The bill acceptor should make noise as stacker cycles and green lights on outside bezel should flash If NO power Due to the different models and brands of Bill Acceptors that are used Examine Bill Acceptor and determine if acceptor is 12 Volt DC or 110 VAC Use meter to measure voltage at cable going into Bill Acceptor If power is OK Clean Bill Acceptor path to make sure there is nothing jamming unit Enter DBA Diagnostics Mode Important Do not hold button down for more than 5 seconds or Bill Acceptor will enter programming mode If programming mode is entered by mistake Unplug game and plug back in To enter Diagnostic Mode press and hold the Diagnostic Button on the back left corner of the DBA for 1 3 seconds The lights above the bill slot will flash the code ERROR CODES Count the number of flashes on front bezel of Bill Acceptor and follow chart for repair FLASHING CORRE
3. Troubleshooting Strategy Use common sense and a systematic method of troubleshooting to determine the exact problem probable cause and remedy Use the process of elimination to find the faulty component Always check for the simple and obvious causes first such as unplugged loose or broken wires and bad sensors bent pinched stuck or jammed components Troubleshooting Chart Problem Probable Cause Remedy Unplugged Check wall outlet No power to the game No lights on at all Circuit breaker tripped Reset power strip breaker switch or building circuit breaker Power strip faulty Change plug position replace if needed Faulty cable power supply See Power Supply diagnostic below Power supply unplugged Insure unit is plugged into power strip AC Light and Bill Acceptor on But everything else off Power supply shutting down See power supply diagnostics to isolate bad because of 12 V overload component A bad motor or 12 volt short Id this Power Supply not ON Faulty power supply See Power Supply Diagnostic below Check for power to Bill Ac Acceptor should cycle stacker at game ceptor power up If not check cable connections Dirt or debris in acceptor Refer to How to Clean Bill Acceptor slot Or clean with bill reader cleaning card Dollar Bill Acceptor not ASCC9000 functioning Pinched broken or discon Check wiring from bill acceptor nected wiring to Main Board AACE9109 Repair or repl
4. 1 1 Gives detailed information on game performance These will be described in more depth on page 14 10 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 1 GAME DIAGNOSTICS The game diagnostics mode will allow you to test the following components to make sure they are working correctly Remove the window from the cabinet BALL LAUNCHER SENSOR e With the ball launcher empty make sure the 4 digit display reads 0 Place the ball into the launcher e Ifthe sensors are working correctly a 1 should appear on the display in place of the 0 if the display reads 1 while no ball is in the launcher it is malfunctioning TARGET SENSORS Place your hand inside each of the targets individually e The lights around the targets should flash if they are working correctly If the lights come on without an object passing through the target they are malfunctioning BALL FLIPPERS Gently push down each flipper to make sure they react To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 2 CREDITS PER PLAY Scroll through the n2 menu with the menu select button Make your selection by pressing the menu button and scrolling through the remaining menus past n10 to exit the menu Factory default settings are highlighted in yellow EN t
5. pue Lg 481080 quawBag 104 9 Aeidsiq t 104 pees f Keds p 104 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 r O 2 gt lt lt A Z c gt 84 lt O z lt 2 TT O gt IT z ACIE gui indir aseuy G ur indiro BSE p uH ATLA E UH pdy J asguz un indio aseys uj ip LI ELT Zier LL p SHON aseyg EZ zsng OS WS B ud zsng 828 404 punog S uid zsng ISCHS F id MIS cud ACE E Wd Bb id 0177 112 fas sco 0000006 gt JON oq peog APER 104 sonsouDeip SI p UMS 1L1 epo eous esJep S 6 UMS apis uBIH JON s Z YMS PAU MOT jueujeJoeg e qnog s UMS sou2jiMsdig peog punog Tek Gases f TF 7524 lo o 1 B ui 2 2 7 77 39 Ea co 50 SD 8D To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 WIRING DIAGRAMS cont Target Inputs a Flipper 2 L chm or as OME ALY ay 4 p wiz t 22 TT ayfield Aux 9107 gt 7 P1 Lowside Ouip ut editi
6. Guide AACE9104 Top Marquee Fluorescent Light Wire Switch 9105 Power Supply Wire Ticket Dispenser AACE9108 Main Board to Ticket Tray Vacuum Form Purple Marquee AACE9109 DBA to Coin Door Vacuum Form Playfield Ball Guide 9110 Slot Sensor to Auger to Fluorescent Light 5 9129 Metal Target Sensor Cover AACE9115 Power Supply to Main Board to Aux Board Decal Marquee Title Bubble AACE9117 Cable to Flipper Solenoid 2 Per Game Decal Marquee Face AACE9120 Cable to Flipper Solenoid 1 Per Game Decal Marquee Arm 9121 Aux Board to Ball Sensor to 2 Target ASDE9112 Decal Marquee Body AACE9125 Aux Board to 1 Target ASDE9114 Decal Marquee Right Ear AACB1437 Display Board 4 Digit ASDE9115 Decal Marquee Bubble 1 AACB1901 Encoder Wheel Board ASDE9116 Decal Marquee Bubble 2 9107 Aux Board 50 9117 Decal Inside Marquee 9110 Back Target Board A5DE9118 Playfield Cover Left 9111 Front Target Board A5DE9119 Decal Playfield Cover Right A5DE9120 Decal Marquee Left Ear A5DE9124 Decal Left Light Cover A5DE9125 Decal Right Light Cover A5DE9126 Decal Back Door Cover AANEWGEN1 Main Board To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PARTS IDENTIFICATION A5BA9100 9111 9110 1437 D S AAPB2700 AALIHL110 m ASLI0001 ASSP1050 ASSP9104 A5ME912
7. 10 will display 0 on all targets and 4 digit display when viewed again after clearing To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 HOW TO INSTALL BILL ACCEPTOR Tools Needed 11 32 Nut Driver or socket wrench 1 Remove 4 nuts from bill acceptor plate and 2 from coin mech bolts 2 Remove black bill acceptor plate 3 Insert Bill Acceptor 4 Install nuts on bill acceptor plate and coin mech 5 Route cables as shown in picture 6 Make sure Bill Acceptor is set to Always Enabled and test To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 CIRCUIT BOARD WIRING AANEWGEN 1 MAIN BOARD 39103 Cable to Count 9107 Menu ers amp Ball Lift Motor Button Cable 25 Oe 99 e 16 9115 12 Volt Power In Cable C 9109 Cables to Coin Door amp Bill Acceptor n J16 9114 Com 7 16 9111 Cable to Cable to I O 1st Sensor 9100 Cable to Speak ers amp Ball Lift Sensor 1 Le 0000S J9 J5 Switch amp Display Sig 9108 Ticket Dispenser Cables nals 9107 AUX BOARD J22 9122 Ball Release Coil J16 9114 J21 9117 L Com cable to J16 Flipper 3 on main board J18 9115 e 12 Volt power in J20 9117 C 2 eg e du Ball Sense 4 9116 J12 9124 Display communication rom J21 on Main Boa
8. 3 4 12v cra ee Input Serial Comm 40 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 MAINTENANCE LOG If you need to make repairs or order replacement parts it is a good idea to keep a log Below is a chart you can use to track repairs and maintenance DATE MAINTENANCE PERFORMED PARTS ORDERED INITIALS To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TECHNICAL SUPPORT Excellent customer service is very important to Bay Tek Games We know that keeping your games in great operating condition is important to your business When you need us we are here to help You can call us for free technical assistance and you can count on us to have parts on hand to sup port your game When you do need us it s important that you know what to expect We offer op tions that fit your needs Electronics Circuit Boards Repair Options Repair amp Return If you have Circuit Board issues with your Bay Tek game you can send the board to us and we ll repair it right away Most items sent to us are repaired and returned to you within two days This option is your best value as we offer this fast turn around service at the most reasonable price Advance Replacement If you have Circuit Board issues with your Bay Tek game but you don t have time to send in your board in for repair give us a call and ask for an Advance Replacement We ll
9. 9 A5M04010 B o ASLKS001 5 1002 W5TM4006 p 4 m 4 sen oo ir nr pom on m n c r PIE sow STATS NUMBER OF siai HITS ASPL9097 A5CB1499 A5CO4203 m o AABR9100 AATG9100 AATISID A5SH9100 AACB4401 34 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PARTS IDENTIFICATION AACE1615 1715 AACE9101 AACE9102 AACE9104 AACE9105 AACE9107 AACE9108 AACE9109 AACE9110 AACE9112 AACE9113 AACE9118 AACE9119 AACE9120 AACE9121 e AACE9125 AACBL4A DOOR ASFI9010 AACE9126 AACE9103 A5ME9111 35 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 DECAL IDENTIFICATION MARQUEE DECALS Pull My Finger Decal Diagram A5DE9109_marquee title bubble A5DE9110_marquee face A5DE9111_marquee arm A5DE9112_marquee body A5DE9114_marquee ear right A5DE9115_marquee bubble 1 A5DE9116_marquee bubble 2 A5DE9120_marquee ear left A5DE9106_marquee side left hidden on picture A5DE9108_marquee side right aes A5DE9100_playfield A5DE9117_inside marquee A5DE9101 outside track A5DE9118 playfield cover left A5DE9102 target front 2 A5DE9119_playfield cover right A5DE9107 cabinet side right A5DE9105 cabinet side left hidden on picture A5DE9121 finger guard front A5DE9122 finger guard back hidden on picture A5DE9123 plunger guard A5DE9103 cab
10. CTIVE CODE ACTION LEDs off Power off Turn on power LEDs on Acceptor is OK 1 flash DESCRIPTION Bill path blockage Un jam bill path Rapid flashing Stringing attempt de during operation tected or sensors dirty 2 flashes 3 flashes 4 flashes 5 flashes 6 flashes Clean the sensors 32 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PARTS LIST PART DESCRIPTION PART DESCRIPTION LIIS Purple 8 Per Game 5 1002 Caster Wheel 5 9101 Ball Yellow 8 Per Game W5TM4006 T Molding 13 16 Yellow 5 1499 Coin box 1000 Counters cover AAALIHL 110 Fluorescent Light Holder Assy ASFIS010 Filter AACE8802 Outlet Strip A5HU1200 Hub 9122 Ball Release Solenoid W Cable Fluorescent light 120v 60hz 2700 Push Button Assy Menu Button 631 Lock with Keys 8811 Speaker W Cable 644 Lock with Keys 9101 Lights on Top of Playfield Back Door Lock with Keys 9107 Goes to Menu Button ASLE9100 Large Leaf 4 Per Game 9124 Low Ticket to Aux Board Motor AACBLAA DOOR Door Cable Plate Replaces Bill Acceptor 4319 Fluorescent Light Cable Power Supply 9100 Speaker to Playfield Lights Spring Pin 32 Per Game 9103 Fl Light to Motor to Ticket Counters Spring Ball
11. E 7 9 DETAILED OPERATIONS MAIN MENU 10 DIAGNOSTICS 11 CREDITS BALLS PER PLAY SETTINGS 12 TICKET PATTERN SETTINGS 13 14 BIG BONUS SETTINGS 15 VOLUME SETTINGS 16 GAME STATISTICS 17 18 HOW TO INSTALL BILL ACCEPTOR 19 CIRCUIT BOARD WIRING 20 CABLE DIAGRAMS 21 25 TROUBLESHOOTING GUIDE 26 30 POWER SUPPLY DIAGNOSTICS 31 BILL ACCEPTOR DIAGNOSTICS 32 PARTS LIST 33 PART IDENTIFICATION 34 35 DECAL IDENTIFICATION 36 WIRING DIAGRAMS 37 40 MAINTENANCE LOG 41 TECHNICAL SUPPORT 42 WARRANTY 43 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 WELCOME TO Pull My Finger Congratulations on your Pull My Finger purchase You already know this product delivers much more than an action filled game with big profits Pull My Finger is in simple terms the epitome of goofy fun It replicates the kind of fun we had as kids and has the innate ability to sweep a family with laughter in a matter of seconds Please take a moment to read through this manual and be sure to contact our factory if you have any questions or would like some more information Pull My Finger has built in playfield diagnostics automatic data tracking viewable on the marquee displays dual ticket trays and a sweet chore ography package that keeps people playing and laughing and playing and well you get the point Enjoy Your business is important to us and we hope you enjoy this game as much as we do
12. PER PLAY PRICE PRICE FREE 525 875 1 00 1 25 1 50 1 75 2 00 N3 BALLS PER PLAY Scroll through the n2 menu with the menu select button Make your selection by pressing the menu button and scrolling through the remaining menus past n10 to exit the menu Factory default settings are highlighted in yellow 12 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 N4 TICKET PATTERNS Scroll through the n3 menu with the menu select button Make your selection by pressing the menu button and scrolling through the remaining menus past n10 to exit the menu 13 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 4 TICKET PATTERNS cont Factory default settings are highlighted in yellow BN 4 gt A S SKILL TICKETS changes with Big Bonus settings in n4 menu see pg 12 The SKILL SHOT values alternate with the regular pattern values on targets 1 amp 2 14 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 N5 BIG BONUS VALUES Scroll through the n5 menu with the menu select button Make your selection by pressing the menu button and scrolling through the remaining menus past n10 to exit the menu Factory default settings are highlighted in yellow The Big Bonus value is presented on the 4 digit display and aids in attracting p
13. To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 FACTORY CONTACT INFORMATION Zo OES HAY y qu o9 ven iN Our Vision We aspire to be the best in the world at developing and manufacturing coin operated games for JOIN SERVICE FIRST NETWORK our customers a This free service is intended to keep you up to date on the latest game information early notification of parts specials pertinent technical bulletins updates on retro fit parts software upgrades amp much more Log on to www baytekgames com parts amp then click on the Service First icon 8 AM 5PM C S T MON FRI Locate All Bay Tek Games Service Manuals and Order Parts online c www baytekgames com PARTS SERVICE P 920 822 3951 x 1101 P 920 822 3951 X 1102 F 920 822 1496 F 920 822 1496 parts baytekgames com service baytekgames com All games proudly manufactured at our factory in Pulaski Wisconsin U S A 2 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TABLE OF CONTENTS FACTORY CONTACT INFORMATION 2 TABLE OF CONTENTS 3 INTRODUCTION 4 INSPECTION 4 SPECIFICATIONS 5 SAFETY PRECAUTIONS 5 HOW TO PLAY 6 QUICK SET UP GUID
14. ace wiring harness Check J8 connector on MainBoard Make sure wires are secure in connector Refer to troubleshooting section of dollar bill Bill acceptor problem acceptor manual included with this game or the diagnostics label of the back of the unit Ensure game makes Dong Check coin switches both should be wired G 2 sound when coin switch is normally open Check wiring to main board ame not coining up triggered Cable AACBL4A DOOR AACE9109 Game set to large amount of Jackpot display will show credits inserted credits per game Enter N2 mode in menu to set credits per game To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TROUBLE SHOOTING GUIDE Problem Game scores wrong values Players think they won bonus Back door removed or broken Game does not score target Faulty target sensor Disconnected loose or broken wires Faulty I O Aux Board Tickets do not dispense or Tickets Owed Wrong amount Display is adding dispensed up correct Check for the correct amount of tickets add ing up on Tick ets Owed Dis play Tickets Owed Display is not adding correctly Game is scoring too soon before coin reaches sensor Probable Cause Faulty sensor Align and clean sensors or replace sen sor AACB9110 Top row sensor AACB9111 Bottom row sensor Skill Shot values are constantly changing and are on a set timer The v
15. alue on the target at instant ball passes sensor is what the player receives The back door has ball guides that help divert the ball Re place back door AADO9100 Align and clean sensors or replace sensor 9110 Top row sensor or AACB9111 Bottom row sensor Check connectors and clean phone jack sockets on I O Aux Board and main board Check for continuity Cable s 9116 9125 9124 Opto Sensor on ticket dispenser dirty Faulty ticket dispenser Notch on tickets cut too shallow Faulty cable Disconnected loose or broken wires Faulty Main Board Game is scoring too soon before coin reaches Slot sensor board Ensure Skill Shot values are changing on display above sensor Check connections and clean phone jack sockets on Aux Board and main board Game pays 5 more tickets than it should One of the ticket dispensers is not seeing the notch signal The dispenser will time out after 5 tickets Blow dust from sensor and clean with isopropyl alcohol Replace with working dispenser to isolate the problem A5TD1 Flip tickets and load upside down to have large cut notch toward opto sensor Check connectors from ticket dis pensers to main board Check for continuity Check cables 1615 9108 Replace main board Score sensor is faulty Align and clean sensors or replace sensor AACB9110 Top row sensor AACB9111 Bottom row sensor The value on the target at instant ball pa
16. ck wiring Replace sensor AACB1901 Check continuity through switch Swap Flipper to isolate problem Replace flipper AAFL9100 Swap Flipper to isolate problem Replace flipper 4 Ohms AAFL9100 Sensor does not see ball in position So game continues to load balls Replace sensor AACE4407 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TROUBLE SHOOTING GUIDE Problem Probable Cause Disconnected loose or broken Check connectors from Ball Re wires lease Solenoid to I O Aux Board Ball release solenoid not Faulty solenoid Check for 13 Ohms across coil working Replace if needed AASO9100 Too many balls on playfield I O Aux Board connection Ensure I O Aux Board has 12 Volt power on J18 Check J16 Com ca ble Faulty I O Aux Board Replace I O Aux Board AACB9107 More information on the I O Aux Board The I O Aux Board has logic on board which monitors sensor inputs and provides 12 volt pulses to coils to operate It provides this information back to main board via the J16 Communication cable AACE9114 It is important that this cable is securely connected to theJ16 socket on the main board Blue colored socket Power game down when disconnecting and reconnecting this cable Wait 10 seconds before power up J16 9114 Communication cable to J16 on main board J18 9115 12 Volt DC Power In J12 9124 Display communication from J21 o
17. et amp ratchet 5 32 Allen wrench or drill with 2 square bit 7 16 socket amp ratchet Locate the package of keys taped to the front of the game It should in clude five sets of either B10 or 644 keys and one set of 631 keys Open the cashbox door with the 631 key and remove the hardware packet and power cord Remove the lower back door with two B10 or 644 keys and take out the hand assembly and guard Also remove the bag of balls 16 total and place them in the ball chute To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 QUICK SET UP GUIDE cont Attach the guard to the side of the cabinet with the three 2 carriage bolts three flat washers and three 5 16 locknuts Make sure the washers go on the in side of the cabinet between the wood and the lock nuts Attach the hand assembly with four black self tapping square bit screws and split washers 70 RP Oo To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 QUICK SET UP GUIDE cont Slide the marquee onto the cabinet from the front making sure the power cable goes safely down the opening without getting pinched Secure the marquee from inside the top back door inserting 1 1 2 hex bolts with split and flat washers into the holes in either side Gm Plug in the marquee power display cables Plu
18. g the cable from the cashbox into the back of the cabinet and connect it to a power source Push the cabinet to its final location and lock the casters Load the ticket trays with tickets Power the game on by switching the power strip to ON Congratulations You re Ready To Go 9 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 DETAILED OPERATIONS MAIN MENU 1 Access the main menu by pressing the MENU BUTTON inside the front door of the cabinet and holding down for 4 seconds 2 Scroll through the menu options shown on the 4 digit display by pressing the MENU BUTTON repeatedly 3 Press the MENU SELECT button to enter and scroll through sub menus described in detail below 1 GAME DIAGNOSTICS n Used to trouble shoot sensors and ball flippers Allows operators to choose the number of credits required 2 CREDITS PER PLAY n to play BALLS PER PLAY n 3 Allows operators to choose how many balls are played per credit TICKET PATTERN Allows operators to choose the desired ticket payout per target BIG BONUS SETTING Allows operators to choose the desired ticket payout shown on the 4 digit display when the Big Bonus is hit GAME VOLUME Adjusts the volume of the game during play after a coin has been inserted 7 ATTRACT MODE VOLUME n Adjusts the volume of the game while it is not in use STATISTICS n 8
19. inet front 50 9104 coin door A5DE9126 backdoor cover not visible from outside game A5DE9124 light cover left A5DE9125 light cover right 36 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 punos 1 punog SUNOS jndu vad indu uio 100g UIE Z JOON UNOS LO IMS M07 104 punoJc punolc SUOTING SAAS 10 punog SunOS CH 1939l cf uang SalAles L uogng S98 Jcsuedsi 39921 10 JMO L JOJOJA Josuadsic 3939 104 punoJey SAIL Om CX WIRING DIAGRAMS lt O lt lt z LLI Z 6 pesnu 8 besrnur 9L L jndu Josues JaDny SL 9 pesnur FL G z Indu Josuag L LL 6 dH UNOG L 8 L UNO esie usas Uld esodind edA ld i 9 pasnun RUNAS G pieuajos aseajay JeBunid SUN peed SUM 2 JeBny eg L SAU IOON AAA Uld Jal asoding adA NOISH3A T33H A f uoiSroA ASH LNASAAAN Jebus lind 3e1 e8 37 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 cont 7 gt lt lt lt 0 2 lt O lt lt gt z LLI Z x C C TOO O O punoJc pasnun pasnun 2
20. layers to the game The Big Bonus jumps randomly between targets 3 and 6 on the playfield S SKILL SHOT changes the alternate values displayed on targets 1 amp 2 A 0 SLIMOIL LADYVL gt SLIMOIL N To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 N6 GAME VOLUME CONTROL Scroll through the n6 menu with the menu select button Make your selection by pressing the menu button and scrolling through the remaining menus past n10 to exit the menu Factory default settings are highlighted in yellow This control is for the volume of the game while it is being played or after a coin has been inserted A drum beat will play an example volume while scrolling through the volume levels N7 ATTRACT VOLUME CONTROL Scroll through the n7 menu with the menu select button Make your selection by pressing the menu button and scrolling through the remaining menus past n10 to exit the menu Factory default settings are highlighted in yellow This control is for the volume of the game while it is NOT being played This game plays fun attracting sounds to lure customers to play A drum beat will play an example volume while scrolling through the volume levels To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 GAME STATISTICS N8 TARGET HIT COUNTER In this statistics mode the number hit
21. n main board Ter J23 9123 Ticket Jackpot Display Cable The I O Aux Board also acts as a connector board for Jackpot Display Board Signals come in on J12 and go to display on J23 Jackpot Display will not work if either cable is faulty 30 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 POWER SUPPLY DIAGNOSTICS Use the following procedure to check the Power Supply for Gen 5 games Start by removing the backdoor to gain access to the Power Supply It is mounted directly to the left of the PCB Look for the small green LED light on the Power Supply circuit board If the light is out there is a short somewhere If the light dims there is an overload in one of the circuits such as a bad motor Turn power OFF Disconnect all 12 volt output wires only Turn power ON Green LED Light Green LED Light comes ON remains OFF Replace Power Supply A5PS1001 Turn power OFF Unplug all outputs from the large PCB Recon nect the 12 volt output wires to the Power Supply Turn power ON Green LED Light Green LED Light Short in PCB comes ON remains OFF Replace Turn power OFF Re Green LED Light That cable or related com ponent is shorted out See connect the outputs at remains OFF h the PCB one at a time Jumper Cable Pin Outs to Wait 60 seconds be see which component might tween tests to turn be at fault power ON Green LED Light dims
22. proval will include a Product Return Form which is required to be included with any incoming shipments Repaired parts will be shipped back using the same method in which they were re ceived Repairs are warranted for 30 days from the date of return shipment 43 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 If we re not having fun something s wrong Larry Treankler CEO PULL MY FINGER IS A REGISTERED TRADEMARK OF BAY TEK GAMES INC TEN Pulaski Industrial Park 1077 East Glenbrook Drive Pulaski Wisconsin 54162 USA 920 822 3951 fax 920 822 8936 e mail sales baytekgames com www baytekgames com 44
23. rd J23 9123 Ball Sense 6 Ticket Jackpot Display L 179116 15 49121To Sensor at Plunger 20 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Coin Door and Bill Acceptor Cable Coin Switches Coin Door Harness 5 9903 AACBL4A DOOR Wired Normal To J6 COIN and J8 on Main Board To Outlet Strip AC Voltage Speaker LED Cable AACE9100 To J19 SPEAKERS and J24 connector on Playfield bottom LED lights AACE9119 To Ball Lift Sensor AACB1901 Ball Lift Sensor Cable AACE9110 Menu Buttons Cable AACE9107 AAPB690 To J25 Connector on Main Board n Menu Select Button CPG OQ 0 KK 21 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Ball Lift Motor amp Counters Cable AACE9103 To Ball Lift Motor A5MO4010 16 Ohms Top LED lights AACE9101 3 e J22 main board Ticket Counter Game Counter Ticket and Game Counters AACO1000 To J21 Connector DIOS SERIO on Main Board MA To I O J12 on Aux Board These are signal lines for Jackpot Display Board Ticket Tray Cable AACE1615 To Ticket Dispenser A5TD1 12 Volt Power Enable Signal Com Ground Notch Signal AACE9108 2nd Ticket Dis Low Ticket Switch Wired Normally Open penser ha
24. s Game Ground A5SW200 wiring 1 4 Spacer ASSENY020 22 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 12 Volt Power Supply Wiring o Power Supply DEM ASPS1001 gt 2 K ut CP Green LED power indicator and voltage adjustment pot Power Supply 12 Volt Cable AACE9115 Power Supply Power Cable AACE9105 To J18 POWER IN Connector on To J18 Con j nector on I O Main Board AUX Board 23 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Ball Sensor Wiring Diagram 1 AACB9110 AACB9110 j AACB9110 AACB9110 AACE9102 AACE9102 AACE9112 HAN AACE9125 XIS AACE9125 9o OO AACB9111 9111 From J10 Connector on Main Board 9111 9113 24 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Ball Sensor Ball Release Jackpot Display and Flipper Wiring Com Cable to J16 on Main Board AACE9114 Ball Release Solenoid AASO9100 13 Ohms Ball Flipper All 3 are the same 4 Ohms AAFL9100 Sensor at Plunger AACE4407 Jackpot Display Board AACB1437 SEs To Sensor at Plunger AACE9121 25 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TROUBLE SHOOTING GUIDE
25. s on each target is displayed e Targets 3 6 should have the lowest counts on them this is the reasoning behind the placement of the Big Bonus values The average tickets paid out per game is also shown on the 4 digit display above the playfield e This information will assist in finding average payout percentage N9 TOTAL NUMBER OF PLAYS In this statistics mode the total number of game plays is shown on the 4 digit display above the playfield e To determine total game income since the last statistics clear multiply this number by the price per play set in n2 of X per income plays play For example 172 plays X 50 per play 86 income To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 N10 SKILL HITS COUNTER This statistics mode will display a count of skill shot hits on targets 1 amp 2 A skill hit is when the ball goes through target 1 or 2 while the higher alternate value is displayed e If these numbers are high you may a very skilled player or shark frequenting your facility This may cause your game to pay out too many tickets Because Pull My Finger is a skill based game this is a possibility The total number of games played is shown on the 4 digit display N11 STATISTICS CLEAR While in n11 mode hold down menu select for 3 seconds to clear the statistics in menus n8 n10 The statistics modes n8 n
26. send you a replacement board that same day pending availability When you get your new board just repackage the defective board in the same box and send it back to us We make it easy by including a UPS Return Shipping label for you to put on the box not available for international shipments This is your best option when you need to get you game up and running as quickly as possible Spare Parts Take matters into your own hands and purchase new spare Circuit Boards for your Bay Tek games Many of our games share the same main board electronics This means you can buy one set of spare electronics to support many of your Bay Tek games Spare boards allow you to get your game up and running the quickest and provide you a valuable troubleshooting option Call our technicians to get recommendations for what you should keep on hand for spare parts Technical Support You are the best tool for troubleshooting Your abilities to understand the game and your skills to repair the game are invaluable to us If you need help you know you can call us It s not easy to diagnose a game remotely by phone but our technicians do a great job They ll need your help to perform some troubleshooting steps and convey to them exactly what s happening with your game Returns Credits amp Fees NOTICE ALL ITEMS being sent to Bay Tek Games for repair or return etc require prior Return Authorization Bay Tek Games will provide a Product Return Form with an au
27. sses sensor is what the The values are constantly changing Player receives and are on a set timer To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TROUBLE SHOOTING GUIDE Problem Targets not lighting up Note Target lights are wired separate from target sensors Jackpot Display not lighting up Jackpot Display says Lo Game looks fine but none of the functions work Probable Cause Volume set to zero in menu Disconnected loose or broken wires Faulty speaker Targets are wired in series If one is faulty all of the targets after it will go dark Check previous target and target which is dark Swap target boards to isolate problem Faulty target sensor Phone Cable to Display is bent pinched or unplugged J12 connector on I O Aux Board to main board disconnected Faulty Display Board Both ticket trays are empty Disconnected loose or broken wires Faulty low ticket switches Faulty Main Board I O Aux Board may be faulty wires disconnected from main board or not receiving 12 VDC power 28 Enter N6 in menu for game volume Enter N7 in menu for attract volume Check connections and reseat J19 on main board Cable AACE9100 Replace speaker 55 1050 Refer to Ball Sensor Wiring Diagram Cable goes from Main Board to bottom sensors to top sensors Check connections and clean phone jack Sockets on targe
28. t work Ball loader will load ball at coin up if no ball is at plunger then cycle 15 seconds twice then go to Err1 It will try again after 40 seconds No Balls on playfield If no ball is preset at coin up game will load one immediately and then try again after 15 seconds Too many balls on playfield Probable Cause Switch not making contact on flipper assembly Disconnected loose or broken wires Flipper solenoid faulty Problem may follow socket on 1 Aux Board Disconnected loose or broken wires Faulty Motor Faulty Main Board Sensor at Plunger blocked or faulty Faulty Ball Load Motor I O Aux Board is not communi cating Ball Lift Sensor faulty causing load motor to always turn Ball Flipper switch faulty causing game to keep loading balls because it can not find them Ball Flipper Solenoid faulty Sensor at Plunger faulty Clean or replace sensor AACB1901 Inspect flipper assembly replace if needed AAFL9100 Check connectors from flipper to I O Aux Board Replace flipper 4 Ohms AAFL9100 Replace I O Aux Board AACB9107 Check connectors from Motor to Main Board Replace Motor 4010 Replace Main Board AANEWGEN 1 Clean sensor check for toggle movement Replace sensor AACE4407 Refer to Ball Load Motor does not work above Aux Board may be faulty wires disconnected from main board or not receiving 12 VDC power Clean sensor Che
29. the game Bay Tek will add another 3 months to your warranty free of charge Bay Tek Games will without charge repair or replace defective component parts upon notification to the parts service department while the game is under warranty Warranty replacement parts will be shipped immediately via ground service along with a Product Return Form for the return of defective parts Defective parts must be shipped back to Bay Tek Games unless otherwise in structed Items not returned to Bay Tek Games will be invoiced as replacement parts This warranty does not apply in the event of any misuse or abuse to the product or as a result of any unauthorized repairs or alterations The warranty does not apply if any serial number decal is altered defaced or removed from its original position In order to maintain the safety amp other compliance certifications of the game ONLY approved parts may be used For approved parts refer to the parts list in this manual Should you need your game serviced determine the serial number from the decal placed on the front of this manual or locate it on the back of the game Then con tact our Service Department at 920 822 3951 or e mail service baytekgames com NON WARRANTY Options and estimated charges will be provided to you for your approval Please remember that any items being sent to Bay Tek Games must include prior re turn authorization from our Parts amp Service Department This ap
30. thorizing Ticket Num ber for each item to be returned Please be certain to include this document with all shipments Late Fees and Non Return Fees Advance Replacement and Warranty Replacement items require the defective items to be returned by Bay Tek games promptly to avoid Late Fees We would expect items to be returned with 10 working days Late fees are invoiced monthly Late fees are non refundable under any circumstance Any item not returned within 90 days will be invoiced in full as a replacement part Bench Fees Bench fees will apply for each electronic item returned to Bay Tek Games this in cludes unused Advance Replacement items This charge covers our cost to inspect evaluate and retest each item Please note that returned items that do not pas our tests will be charged accord ingly as replacement items or advance replacements Restocking Fees Unused items returned for credit will be credited minus a restocking fee Items must be returned with in 30 days of purchase in order to qualify for any credit amount No shipping charges will be credited BAY 5 a To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 WARRANTY Bay Tek Games warrants to the original purchaser that all game components will be free of defects in workmanship and materials for a period of 6 months from the date of purchase If you fill out the registration card in the cashbox of
31. ts See the serial num ber decal located on the back of the game cabinet Always plug game into a grounded circuit If the supply cord is damaged it must be replaced by a special cord or assembly available from the manufacturer or its service agent To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 HOW TO PLAY Pull My Finger Pull My Finger is a bright and colorful ticket redemption game that encourages players to pull the monkey s finger which shoots a ball into the playfield where six targets are located The targets display alternating ticket values for an added challenge If timing and accuracy are on point players can win the big bonus This selectable bonus ranges from 25 tickets all the way up to a whopping 1000 bonus tickets Factory default is 250 If the ball does not go straight into a target automatic flippers have been installed on the playfield to keep the ball bouncing until it is launched into a target The large bright and colorful cabinet draws players to this simple ticket redemption game while the charismatic monkey keeps kids of all ages highly entertained time and time again Standard features include dual ticket dispensers adjustable bonus patterns built in diagnostics and performance tracking software To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 QUICK SET UP GUIDE Tools needed 1 2 sock
32. ts and main board Note Top row sensors are different from bot tom row sensors Replace sensor AACB9110 Top row sensor AACB9111 Bottom row sensor Check connections and clean phone jack Sockets on display board and I O Aux board Replace cable if needed AACE9123 Check connections and reseat J12 and J21 on main board Cable AACE9124 Replace Display Board AACB1437 Refill trays with tickets Check connections and reseat J21 on main board Cable s 9124 9108 1615 Switches wired normally open Replace switches AbSW200 Replace main board Part AANEWGEN 1 Check I O Aux Board for any disconnected wires Check 12 Volts DC to J18 Check J16 plug on I O Aux Board to J21 on main board To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TROUBLE SHOOTING GUIDE Err 1 means there is no ball in front of plunger after coin up There can be multiple causes including Display shows Err 1 Not enough balls in game Playfield Kicker not working Ball Load motor not working Ensure 16 balls in game Refer to Playfield Kicker not working below Refer to Ball Load Motor not working below Ball release solenoid not working Refer to Ball Release Solenoid not working below Ball load sensor not seen Problem Playfield Flipper not working One ball stuck in front of Flipper Swap inputs on I O Aux board to verify flipper fault Ball Load Motor does no
Download Pdf Manuals
Related Search