Home

Kilotech weighing scale KWS

Contents

1. TEST SUBMENU1 REMARK DISP test LCD or LED details refer to section17 COM1 RD test COM1 receiving details refer to section19 COM1 TD test COM1 transmitting details refer to section20 COM2 RD test COM2 receiving details refer to section19 COM2 TD test COM2 transmitting details refer to section20 KEY test keys and buzzer details refer to section18 Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 20 KWS CY Operation amp Service Manual 5 Normal Weighing mode 5 1 During key operation please note to use the second function of one key need pressing the key over 3 seconds To input data or select menu use lt t l gt e gt to process 5 2 Power on scale when scale is off short press ON OFF key to turn on Power off scale when scale is on long press ON OFF key to turn off the scale 5 3 Change working mode long press FUNC key then iT y to choose and confirm to enter into weighing mode counting mode or percentage working mode 5 4 Enter to or exit from HOLD mode press HOLD key 5 5 ZERO When the weights is stable and within the zero range press ZERO key to set new zero point Please refer the ZERO and TARE limitations in 5 9 section 5 6 TARE When the gross weight is big than zero and the scale is stable press TARE key the indicator will show net weight of zero the NET announciator will be lighted Please refer the ZERO and TARE limitations in 5 9
2. Bit Byte 1 H1 Byte 2 H2 Byte 3 H3 Byte 4 H4 o P stable O not under capacity 00 compare disable 00 normal weighing 1 not stable 1 under capacity 01 lower limit 01 count weighing 4 O not at zero point 0 not over capacity 10 0k 10 percent weighing i 3 11 upper limit 11 other mode 1 at zero point 1 over capacity o O RAM ok O ROM ok O gross weight O not in HOLD 1 RAM error 1 ROM error 1 net weight 1 in HOLD 3 0 eeprom OK O calibration ok O initial zero ok O battery ok 1 eeprom error 1 calibration error 1 initial zero error 1 low battery 4 lalways 1 always 1 always 1 always 1 5 jalways 1 always 1 always 1 always 1 6 jalways 0 always 1 always 1 always 0 7 parity Parity parity Parity 23 6 Communication when USER COM1 2 LAYOUT is set to SINGLE 23 6 1 Commands and response 23 6 1 1 Command W lt CR gt 57h Odh request current reading Response RLE gt MMMmmMA y Us UgU Us lt CR gt lt LF gt H1H2H Hy lt CR gt lt ETX gt over capacity xLF gt Wh aor ci aN SP U Us U3 U Us lt CR gt lt LF gt HAHA H 4 lt CR gt lt ETX gt under capacity G2LF gt UU Us U4Us lt CR gt lt LF gt H H2H3 H4 lt CR gt lt ETX gt zero point error Note UU U3 U4Us is 1 2 3 or 5 bytes according to current unit kg Ib pcs Ib oz 4xLF gt lt P gt W W W3W Ws lt DP gt W g U1U2 U3 U Us lt CR gt lt LF gt H HsH3 Ha lt CR gt lt ETX gt normal data Note 1 The decimal point position is determined by CONF
3. CAL Pi line calibration pointi do first weight point calibration this point can t be omitted and standard weight must be over 10 FS END Y YES NO End calibration YES go to CAL END to end NO go to do next point calibration CAL P2 line calibration point2 do second weight point calibration standard weight must be over 10 FS and be larger than it in CAL P1 this point can be omitted END Y YES NO End calibration YES go to CAL END to end NO go to do next point calibration CAL P3 line calibration point3 do third weight point calibration standard weight must be over 10 FS and be larger than it in CAL P2 this point can be omitted CAL END calibration end and restart NOTE The details can be referred in section 12 CALIBRATION Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 19 KWS CY Operation amp Service Manual 4 5 MISC Submenu MISC SUBMENU1 REMARK display ADC s code this code can be after no filter filter1 or filter2 details refer to CODE section12 VOL display voltage calibrate voltage set full charged voltage and low battery voltage details refer to section13 DATE display date and set date details refer to section17 TIME display time and set time details refer to section16 VER display firmware version details refer to section18 4 6 TEST Submenu
4. Read the weight reading in short time after loading The output signature of load cell and electronic circuit may be little influenced after weighing for a long time Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 3 KWS CY Operation amp Service Manual 1 Specification 1 1 Housing and Outline Dimension ZERO ON OFF gt Left View Front View Right View Back View If 4 pin socket replace DB9 to be used as load cell connector and or foot switch is used the outline is similar as following shown Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 4 KWS CY Operation amp Service Manual RS232 interface 1 2 Power Supply 1 2 1 if 4xAA size alkaline batteries are used When all displayed segments of LCD flashed this prompt you d better to replace batteries When Lo bAt displayed this prompt you should replace batteries immediately otherwise it will turn off automatically in 10s 1 2 2 If optional 4xAA NIMH rechargeable batteries package are used when above cases comes use USB or AC adapter to power indicator 1 2 3 AC Adapter 6Vpc 500mA with central negative 1 2 4 USB power supply if USB interface is installed ey 1 2 5 Work current lt 15mA with backlight off no optional Bluetooth Module and no load cells lt 30mA with backlight on no optional Bluetooth Module and no load cells lt 50mA with backl
5. for positive Decimal point 1 byte Measure unit 1 5bytes Ib kg Ib 0z pcs Units are always lower case left aligned Current status 4bytes 23 4 2 If the weight is overcapacity the scale will return eight characters the field of polarity decimal point weight data is filled by AT 23 4 3 If the weight is under capacity it will return eight _ characters the field of polarity decimal point and weight data is filled by _ 23 4 4 If the zero point is error it will return eight weight data is filled by 23 4 5 Useless leading 0 before digits is suppressed Reading weight is right aligned i characters the field of polarity decimal point and 23 5 Key to symbols used lt LF gt Line Feed character hex OAH lt CR gt Carriage Return character hex ODH lt ETX gt End of Text character hex 03H lt SP gt Space hex 20H HHH Ha Four current status bytes lt P gt Polarity character or W 1 W6 Reading data 1 6 bytes six digits lt DP gt Decimal point LU UA Measure units kg Ib lb 0z or pcs 2 5 bytes lt Add gt Address of scale 2 bytes 00 99 lt Prompt gt Prompt characters of output content max 11bytes Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 35 KWS CY Operation amp Service Manual The bit definition of HHH Ha
6. 11 4 When CONFIG FUNC ACCUMU is set to AUTO the stable and positive displayed net weight must be larger than USER OTHER NLD RNG piece or percentage can be accumulated automatically and indicator will display accumulation times first and then display total of number To avoid repeating accumulation for same load one load only can be accumulated once So before a new load put onto the scale the original load should be removed and let load on scale be smaller than USER OTHER NLD RNG 11 5 To view total when display number is zero long pressing TOTAL key and indicator will display accumulation times first and then display total of number NOTE When HOLD function is enable and scale is working in PEAK HOLD mode CONFIG HOLD YES USER HOLD HLD MOD PS PEAK NG PEAK Accumulation function will be automatically disabled 12 Calibration Note 1 Before calibrate the scale you should prepare a standard weight more than 10 of FS weight for calibration 2 In following steps to press ON OFF will show EXIT and press ON OFF again or press TARE will exit calibration 12 1Go to setup mode select CAL then press TARE to confirm to enter calibration mode 12 2After entering this mode the number of this indicator has been calibrated will be shown first this number will be increased one after every calibration and calibration data saved and this counter can t be modified or erased by any other ways it counts from 0000 t
7. 6023 or 6026 Page 40 25 2 Troubleshooting KWS CY Operation amp Service Manual SYMPTOM PROBABLE CAUSE REMEDY Ad Load cell wires to indicator are Make sure wires are ok and correctly incorrectly connected or shorted or connected Replace load cell or ADC Ad opened or ADC load cell are damaged chip Service required SE Weight reading exceeds Power On Zero Make sure scale platform is empty limit Perform zero calibration A Weight reading below Power On Zero Install platform on scale Perform MR limit zero calibration Reduce load on scale until weight Weight reading exceeds Overload limit f value can be displayed Use a more EE or The weight value cannot be displayed f f _ appropriate unit of measure Re set in the current unit of measure because it Gg some parameters of CONFIG or exceeds 6 digits UAER S Install platform on scale Ee Weight reading below Under load limit nse Perform zero calibration Kier CONFIG or CAL parameters are not Re set items in CONFIG do correctly set calibration EEP E2 USER parameter is not correctly set Re set items in USER Set PRIM N PRIM d SECND n to CAP ER Capacity parameters are not correct correct number make sure capacity not more than 6 digit Calibration error maybe input data or Input correct data load correct CAL Er loaded weight is too small too big weight onto platform Service unstable un linear required P
8. 24448pcs PIECE WT 0 05kg ACC N 10 TOTAL 23456pcs DATE 2011 06 12 Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 38 23 7 3 3 In percent weighing mode 23 7 3 4 In BMI mode Kilotech Inc KWS CY Operation amp Service Manual TIME 12 34 56 A D CODE 1234345 VOLTAGE 6 7V STATUS bpq2 SCALE ID 123456 GROSS 12345lb TARE 10lb NET 12335lb PERCENTAGE 91 4 1 REF WT 135lb ACC N 3 TOTAL 271 6 DATE 2011 06 12 TIME 12 34 56 A D CODE 1231234 VOLTAGE 6 7V STATUS bpq2 SCALE ID 123456 GROSS 110 0kg TARE 10 0kg NET 100 0kg HEIGHT 170cm BMI 34 6 DATE 2011 06 12 TIME 12 34 56 A D CODE 1231234 VOLTAGE 6 7V STATUS bpq2 USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 39 KWS CY Operation amp Service Manual 25 Meaning of Some Symbols and Troubleshooting 25 1 Meaning of Symbols 25 1 1 0 een Zero is over the setting range 25 1 2 0O Zero point is below the setting range 25 1 3 A o Signal to ADC is over max range 25 1 4 Ad_____ Signal to ADC is below min range EAR Weight is over upper limitation or display data is over limitation 25 1 6 i 7 Weight is below lower limitation 25 1 7 EEP E1 CONFIG or CAL parameters are not correctly set 25 1 8 EEP E2 USER parameter is not correctly set 25 1 9 Lo bAt Battery voltage is lower than setting 25 1 10 CAP Next displaying content is Ca
9. 800 694 4445 Service EXT 6023 or 6026 Page 42 KWS CY Operation amp Service Manual 26 Display Character ASCII LCD LED Show ASCII LCD LED Show ASCII LCD LED Show 1 B H o 0 2 d c H P H 3 4 D d Q al 4 U E E R pa 5 di F E S L 6 E G E T E cal al 8 e H vlog e DH s d wo g K H x H L vi 3 M o z 4 Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 43 27 Packing List KWS CY Operation amp Service Manual No CONTENT QTY 1 Indicator 1 2 User manual 1 3 Swivel bracket 1 4 AC Adapter 1 5 RS232 cable Optional 6 USB interface Optional 7 USB cable Optional 8 Bluetooth Module Optional 9 1x CR2032 battery for RTC Optional 10 4xAA Alkaline batteries Optional 11 4xAA NIMH batteries package optional 28 Version History VERSION DESCRIPTION DATE V1 0 Initial version 2011 09 21 Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 44
10. YES NO Yes No enable disable output date Prompt is NO DATE TIME YES NO Yes No enable disable output time Prompt is NO TIME AD CODE YES NO Yes No enable disable output ADC s code NO Prompt is A D CODE BAT VOL YES NO Yes No enable disable output voltage of battery NO Prompt is VOLTAGE ACCUMU YES NO Yes No enable disable output accumulation NO times and total Prompt is ACC N and TOTAL STATUS YES NO Yes No enable disable output scale s status NO Prompt is STATUS B LINE NONE LINE1 How many blank lines after strings output NONE no blank line LINE1 2 3 4 there re 1 2 3 LINE2 LINE1 or A Dank lines after strings used for paper feed LINES forward 1 2 3 4 lines LINE4 COM2 BAUD RT 1200 2400 4800 9600 9600 selection of com2 s baud rate 19200 38400 BYT FMT 8N1 selection of com2 s byte format 1 8N1 8 data 701 8N1 bits No parity check bit 1 stop bit 2 701 7 data bits 1 Odd parity check bit 1 stop bit 3 7E1 7 7E1 data bits 1 Even parity check bit 1 stop bit OUT MOD CONT Selection com1 output mode PRINT 1 CONT continuously output 2 PRINT output after PRINT key pressed 3 CMD output after a request command is received 4 PRT CMD CMD PRT CMD output after PRINT key pressed or request command received 5 STABLE output after scale is stable PRT CMD Note use PRINT or CMD to output data the scale must be stable STABLE Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EX
11. and low 5 13 3 After HIGH being shown 000000 will be displayed use PRINT ACC UNIT key to input high weight number and press TARE key to confirm Announciator of Hi will be shown in this step Press ZERO key to exit and back to weighing mode 5 13 4 After Low being shown 000000 will be displayed use PRINT ACC UNIT key to input low weight number and press TARE key to confirm Announciator of Lo will be shown in this step Press ZERO key to exit and back to weighing mode NOTE If High number is 0 or is equal or less than low number the comparison will be disabled and the input data has no limitation 5 13 5 After a reasonable limitation is set and compare is be active one of announciators HI OK LO will be lighted and the beeper will sound according to its setting in USER BEEP 5 14 Enter Setup Mode 5 14 1 If need to set configuration parameters set user parameters calibrate the scale set current date or time test some hardware It s need to long press SETUP key to enter setup mode 5 14 2 After Entering Setup Mode the main menu item CONFIG will be shown first 5 14 3 In Setup mode use y t l j ge L to select wanted submenu and wanted menu item select wanted choice set wanted number confirm and save data or exit this mode Please refer the 4 Operation Menu Structure 6 Count Weighing Mode 6 1 In this mode scale will weigh goods weight on scale calculate and display its counts after the piece weight o
12. announciator become steady the displayed number is frozen 10 Data Compare Function 10 1 Data compare function can be used in normal weighing mode counting mode and percent weighing mode and call it as Check Weigher Check Counts and Check Percentage When this function is enabled you can set a higher and a lower limitation of weight counts or percentage independently and these limitation can be saved permanently Then the current data of weight counts or percentage will be compared with the setting limitation and corresponding announciator will be lighted 10 2 To make data compare function be available CONFIG FUNC COMPAR menu item should set to YES and high and low limitation should be set correctly according to following steps 10 3 In in normal weighing mode counting mode or percent weighing mode Press down DATA key more than 3s to enter input compare data of high and low mode 10 4 After HIGH being shown last setting data of high will be displayed use PRINT ACC UNIT key to input new number of high and press TARE key to confirm Announciator of Hi will be shown in this step Press ZERO key to exit and back to original working mode 10 5 After Low being shown last setting of low will be displayed use PRINT ACC UNIT key to input new number of low and press TARE key to confirm Announciator of Lo will be shown in this step Press ZERO key to exit and back to original working mode NOTE If High number is O or is equal or le
13. key the value of this key will be displayed on position and buzzer will beep whatever USER BEEP KEY item is set 20 3 Press SETUP key to return to last menu item press ON OFF key to prepare to exit this mode 21 Serial Port1 2 COM1 2 Receiving Test 21 1 Before test the receiving function of COM1 or COM2 a cable is need to connect a PC and this indicator and a software be similar with Super Terminal of Windows is also need to run on PC to send bytes to this indicator Please note baud rate is selected by USER COM1 2 BAUDRT 8N1 byte format is fixed Hex data 0x00 Oxff are used 21 2 Press down SETUP more than 3s to enter SETUP mode using PRINT or ACC key to select TEST COM1 RD or TEST COM2 RD item press TARE to enter test COM1 2 receiving function and rd1 or rd2 will be displayed first 21 3 In this mode received hex data 0x00 Oxff will be displayed on position 21 4 Press SETUP key to return to last menu item press ON OFF key to prepare to exit this mode 22 Serial Port1 2 COM1 2 Transmitting Test 22 1 Before test the transmitting function of COM1 or COM2 a cable is need to connect a PC and this instrument and a software be similar with Super Terminal of Windows is also need to run on PC to receive bytes from this instrument Please note baud rate is selected by USER COM1 2 BAUDRT 8N1 byte format is fixed Hex data 0x00 Oxff are used 22 2 Press down SETUP more than 3s to enter SETUP mode using
14. programmable 1 8 Analog Circuit characters 1 8 1 24 bit A D converter 1 8 2 Conversion Speed 10Hz or 80Hz selectable 1 8 3 Input range 15mV to 15mV 1 8 4 Output code 1mV input will output about 100 000 raw counts 1 8 5 With Hardware low pass filter and 2 programmable digital low pass filters 1 9 Capacity and Division Programmable 1 9 1 Max display range 999 999 to 999 999 1 9 2 Division number range for primary unit 100 100 000 Division number range for second unit 100 150 000 Division number will be limited by REGULA setting 1 9 3 Recommended Sensitivity gt 1uV display division 1 10 Accuracy lt 0 01 Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 6 KWS CY Operation amp Service Manual 1 11 Calibration Method 1 11 1 Software calibration with long term storage in EEPROM 1 11 2 Provides smooth curve fit through four points 1 11 3 Calibration can be done under kg or Ib weight unit with 10 100 FS standard weight 1 11 4 Directly weight fine adjustment 10 1 12 Real Clock optional built in nonvolatile real time amp date 1 13 Other Main Function 1 13 1 Programmable Zero Range 1 13 2 Programmable pre set tare weight 13 3 Programmable automatic zero point tracking 13 4 Programmable motion detection window 13 5 Programmable auto power off time backlight working mode 13 6 Programmable hold function with peak weight holding dynamic weighing 13 7 Available Check We
15. scale will always catches and refresh positive larger number and display it To exit HOLD mode press HOLD key again 9 3 2 Negative Peak HOLD When USER HOLD HLD MOD is set to NGPEAK the hold mode is negative peak hold mode When scale first enters this working mode it will display the largest negative number that is from the time of zero point set After entering this working mode scale will always catches negative larger number and display it To exit HOLD mode press HOLD key again 9 3 3 Toggle HOLD When USER HOLD HLD MOD is set to TOGGLE the hold mode is toggle hold mode a manual Hold function After entering this working mode scale will freeze and display number if scale is stable Only the weight that is over USER OTHER NLD RNG zero dead band can be held To exit HOLD mode press HOLD key again If the time of scale being unstable is more than USER HOLD STB TIM STB ER will be shown press TARE key to start averaging again or press HOLD key to exit 9 3 4 Average HOLD When USER HOLD HLD MOD is set to AVERAG the hold mode is average hold mode After entering this working mode scale will freeze and display number if scale is stable If scale is not stable but the variation is less than USER HOLD DYN RNG scale will average data in USER HOLD AVG TIM then freeze and display the number Only the weight that is over USER OTHER NLD RNG can be frozen Scale will exit HOLD mode according to the setting of USER HOLD HLD TIM If the tim
16. shown use PRINT ACC UNIT key to input new unit percentage weight press HOLD key more than 3s to input decimal point Press TARE key to confirm and save it then go back to percent weighing mode If the calculated unit percentage weight is less than 0 5d the indicator will display Pct Er and go back to percent weighing mode 7 5 2 Obtain unit percentage weight by weighing samples weight which percentage is known in percent weighing mode press UNIT key When InP Pct is shown use PRINT or ACC key to select SPL Pct press TARE key to weigh samples which percentage is known weight calculate piece weight Press ZERO key to exit and back to percent weighing mode 7 5 2 1 When SPL Lo is shown move away any sample on scale and press TARE key to confirm before scale is stable SPL Lo will be flashed After it is stable it will go to next step Press ZERO key to exit and back to percent weighing mode 7 5 2 2 When SPL Hi is shown put samples its percentage is known onto the scale Press TARE key to confirm reading weight Before scale is stable SPL Hi will be flashed After it is stable it will go to next step Press ZERO key to exit and back to percent weighing mode 7 5 2 3 After INP PCT being shown 000000 position of decimal point is determined by CONFIG FUNC PERCEN setting will be displayed use PRINT ACC UNIT key to input the percentage of samples and Press TARE key to confirm If the calculated unit percentage weight is Kilotech Inc
17. use PRINT or CMD to output data the scale must be stable STABLE LAYOUT com1 output content and format set 1 MULTPL MULTPL the following selected item in OUT1 will be output MULTPL use defined format 2 SINGLE only displayed SINGLE content and current status will be output it s compatible with NCI SCP01 OUT1 SCAL ID YES YES Yes No enable disable output scale s ID number NO Prompt is SCALE ID GROSS YES NO Yes No enable disable output gross weight NO Prompt is GROSS TARE YES NO Yes No enable disable output tare weight NO Prompt is TARE NET YES YES Yes No enable disable output net weight Prompt NO is NET PERCNT YES NO Yes No enable disable output weight percentage NO Prompt is PERCENTAGE UPCTWT YES NO Yes No enable disable output weight of 1 NO percentage Prompt is 1 REF WT COUNT YES NO Yes No enable disable output counts Prompt is NO QUANTITY Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 14 KWS CY Operation amp Service Manual POWT YES NO Yes No enable disable output piece weight NO Prompt is PIECE WT BMI YES NO Yes No enable disable output height and BMI NO Prompt is HEIGHT and BMI ACCUMU YES NO Yes No enable disable output accumulation NO times and total Prompt is ACC N and TOTAL DATE
18. when data compare is enable and current data weight pieces or percent is over its upper setting limitation turns on when data compare is enable and current data weight pieces or percent is between its high limitation and low limitation turn on when data compare is enable and current data weight pieces or percent is below its lower limitation turn on when battery is used or charged USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 8 KWS CY Operation amp Service Manual 3 Summary of Key function Weighing Counting Percent Enter or exit HOLD mode press down lt 3s Weighing Counting Percent To enter setup mode press down gt 3s Input data mode press down gt 3s to input decimal point Input data mode press down lt 3s Return to last sub menu Menu selection mode Return to last sub menu Weighing Counting Percent RON Output data to serial communication port press down lt 3s PRINT Weighing Counting Percent select working mode weighing counting or percent FUNC press down gt 3s S SE ed t Input data mode The digit on flashed position add 1 Menu selection mode To last item of current menu Weighing Counting Percent To add up current weight pieces percentage to memory press down lt 3s display times and total of accumulation ACC TOTAL Weighing Counting Percent f f To display times and total of accumulation press down gt 3s Input data mode the digit on fl
19. CC UNIT keys to input the value of the loaded weight Press TARE key to confirm then the indicator will flash the input standard weight When this weight number becomes steady it means the stable and reasonable data corresponding to the standard weight has been gotten Then the indicator will automatically go to next step If this point can t be calibrated correctly maybe the weight load onto scale is too small maybe the input data is incorrect it will display CAL Er and return back to step12 5 1 for re calibration 12 5 3 When End y is shown and y is flashing it s waiting command to exit calibration or go on next calibration Use PRINT or ACC key to select yes or no use TARE to confirm If yes is selected it will go to step10 6 to end calibration if no is selected it will go to next step 12 5 4 When 100 FS weight is displayed after CAL P2 being shown It will be calibrated on standard weight for second point Put corresponding weight more than 10 FS weight and larger than the weight used on CAL P1 onto scale Next operation is same as what in step12 5 2 12 5 5 When End y is shown and y is flashing Use PRINT or ACC key to select yes or no use TARE to confirm Similar with doing in step12 5 3 12 5 6 When third standard weight displayed after CAL P3 being shown It will be calibrated on standard weight for third point Put corresponding weight more than 10 FS weight and larger than the weight used on CAL P2 onto scale Next oper
20. IG PRIM D 2 If current unit is Ib oz the format will be similar with following lt LF gt lt P gt W W W lb lt SP gt W W lt DP gt W 0z lt CR gt lt LF gt HAH H4 lt CR gt lt ETX gt 23 6 1 2 Command S lt CR gt 53h Odh request current status Response lt LF gt H HsH3 H 4 lt CR gt lt ETX gt 23 6 1 3 Command Z lt CR gt Gab Odh Response Zero function is activated simulate ZERO key and it returns to current scale status lt LF gt H H2H3H4 lt CR gt lt ETX gt If ZERO function cannot be activated it will return to current scale status 23 6 1 4 Command T lt CR gt 54h Odh Response TARE function is activated simulate TARE key and then returns scale status lt LF gt HHH Ha lt CR gt lt ETX gt If TARE function cannot be activated it will return to current scale status 23 6 1 5 Command U lt CR gt 55h Odh Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 36 KWS CY Operation amp Service Manual Response Changes units of measure simulate UNIT key and return scale status with new units The new measure unit should be allowed to use lt LF gt Us U3 U Us lt CR gt lt LF gt H H2H3 H 4 lt CR gt lt ETX gt 23 6 1 6 Command L lt CR gt 4ch Odh Response If Hold function can be activated it will enable disable hold function simulate HOLD key and returns scale status lt LF gt H H2H3H4 lt CR gt lt ETX gt 23 6 1 7 Command X lt CR gt 58h Odh Response
21. KWS CY Operation amp Service Manual Kilotech weighing scale KWS CY Service Manual V1 0 KWS CY 60 KWS CY 150 KWS CY 300 60 kg x 0 02 kg 132 Ib x 0 05 lb 150 kg x 0 05 kg 330 Ib x 0 1 Ib 300 kg x 0 1 kg 660 lb x 0 2 lb Contents Subject to Change without Notice Kilotech Inc KWS CY Operation amp Service Manual CONTENT T Specificato N E 4 PAY d o F mame ene E T E E 8 3 Summary Of Key function oooooonnnnnnnnnnnnnnencononannnnnnnnnn cnn nennonannnnnnnnnnanenne 9 5 Normal Weighing MOdEe 2 cccccececeeeeeeeneeneeeeeeeeeeseeeeeeeeeeeeeeeeeeeeeeeaes 21 6 Count Weighing MOG cccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaeeneeseeeeeeeeeees 24 7 Percent Weighing Mode 22 cssceccceeeeeeeeeeeeeeeeeeeeeeaeeeneeneeeeeeeeeenenes 26 8 BMI Working Mode 000 27 9 HOLD FUNCION EE 27 10 Data Compare Function sssssssssnnsnnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn mnnn 29 11 ACCUMUlAION da 29 12 UL EE 30 13 Weight gu TE 31 14 Display ADC output e TE 32 15 Display and Calibrate Power Voltage cseeeeeeeeeeeeeeeeeeeeeees 32 16 Display and Set TiMB ooonnccccccccononcccnannnnnnnnnnoncnnonnnnnnnnnnnnn erre croacia 33 17 Display and Set Late eeesgkegesrkegeutageesENEEESEKEEEEESERRRESENEEEEEEEEEEEE 33 18 Display Firmware Version ccseeeceeeeseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 33 19 Display TOS E 33 20 Keyboard and Buzzer TeSt ccccccecceeeneneeeeeeeeeee
22. LD key to enter NG PEAK HOLD mode if weight is over NLD RNG and stable the data will be frozen until press HOLD AUTO key again to exit 5 AVERAG Average HOLD mode in this mode if weight is over TOGGLE NLD RNG and its variation is less than DYN RNG the average data in AVG TIM will be frozen Press HOLD key or HLD TIM time elapsed to exit this mode 6 AUTO Auto hold AVERAG mode it s similar with AVERAG mode but if the one held load is removed and a new load that is over NLD RNG put on scale the new load will be automatically frozen AUTO AVG TIM 1 60 3 average data time for HOLD mode 1 60s STB TIM 3 AVG TIM ER Waiting time for scale stable in HOLD mode 255 AVG TIM 3 AVG TIM 2555 Data HOLD time O data will be frozen until HOLD key pressed 1 65535 data frozen time is HLD TIM 0 65535 0 1 65535s after the time elapses scale will exit HOLD mode Vibration range of data that can be averaged and held in HOLD mode O any data can be HLD RNG 0 255 5 averaged 1 255 only the data which vibration is in 1 255d can be averaged and held OTHER 1 255 the range of weight is 1 255d when current weight is less than this value the scale NLD RNG 1 255 10 can be regarded as empty or the load on scale is removed It must be bigger than CONFI MOTION CMD SRC NONE Source of the executed command selection 1 NONE no any command will be executed COM 1 COM 1 2 COM 1 command from COM1 will be executed 3 COM 2 comman
23. PRINT or ACC key to select TEST COM1 TD or TEST COM2 TD item press TARE to enter test COM1 2 transmitting function and td1 or td2 will be displayed first 22 3 In this mode transmitted hex data 0x00 Oxff will be displayed on position and HOLD PRINT ACC UNIT TARE keys can be used to modify transmitted data 22 4 Press SETUP key to return to last menu item press ON OFF key to prepare to exit this mode 23 Details about Serial Communication 23 1 COM1 is RS232 communication wires come from RS232 connector and TXD1 RXD1 and GND are used 23 2 COM2 can be RS232 or RS485 if used as RS232 communication wires come from RS232 connector and TXD2 RXD2 and GND are used if used as RS485 communication wires come from RS485 Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 34 KWS CY Operation amp Service Manual connector and A and B are used if need GND or 5VCC1 can be used Please refer to section 22 2 22 3 4 5 22 3 7 9 for jumper connector details 23 3 The baud rate and byte format is set by USER COM1 2 BAUD RT and USER COM1 2 BYT FMT Responses to serial commands will be immediate or within one weight measure cycle of the scale One second should be adequate for use as a time out value by remote controlling device 23 4 The length of each item in a transition string 23 4 1 Reading data 6bytes Data polarity 1byte for negative and followed the first digit
24. T 6023 or 6026 Page 15 KWS CY Operation amp Service Manual LAYOUT MULTPL com2 output content and format set 1 MULTPL the following selected item in OUT2 will be output SINGLE MULTPL use defined format 2 SINGLE only displayed content and current status will be output it s YES compatible with NCI SCP01 OUT2 SCAL ID YES YES Yes No enable disable output scale s ID number NO Prompt is SCALE ID GROSS YES NO Yes No enable disable output gross weight NO Prompt is GROSS TARE YES NO Yes No enable disable output tare weight NO Prompt is TARE NET YES NO Yes No enable disable output net weight Prompt NO is NET PERCNT YES NO Yes No enable disable output weight percentage NO Prompt is PERCENTAGE UPCTWT YES NO Yes No enable disable output weight of 1 NO percentage Prompt is 1 REF WT COUNT YES NO Yes No enable disable output counts Prompt is NO QUANTITY PCWT YES NO Yes No enable disable output piece weight NO Prompt is PIECE WT BMI YES NO Yes No enable disable output height and BMI NO Prompt is HEIGHT and BMI ACCUMU YES NO Yes No enable disable output accumulation NO times and total Prompt is ACC N and TOTAL DATE YES YES Yes No enable disable output date Prompt is NO DATE TIME YES YES Yes No enable disable output tim
25. USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 26 KWS CY Operation amp Service Manual less than 0 5d the indicator will display Pct Er and go back to percent weighing mode otherwise after the reasonable unit percentage weight being got the scale will go back to percent weighing mode The got unit percentage weight can be saved after the power off and can be used next time 7 6 Check Percent percentage compare in Percent weighing mode 7 6 1 To make percentage compare function be available CONFIG FUNC COMPAR menu item should set to YES and high and low limitation of percentage should be set correctly according to following steps 7 6 2 In percent weighing mode Press down DATA key more than 3s to input compare data of high and low 7 6 3 After HIGH being shown 000000 will be displayed use PRINT ACC UNIT key to input high percentage number and press TARE key to confirm Announciator of Hi will be shown in this step Press ZERO key to exit and back to percent weighing mode 7 6 4 After Low being shown 000000 will be displayed use PRINT ACC UNIT key to input low percentage number and press TARE key to confirm Announciator of Lo will be shown in this step Press ZERO key to exit and back to counting mode NOTE If High number is 0 or is equal or less than low number the comparison will be disabled 7 6 5 After a reasonable limitation is set and compare is be active one of announciators HI OK LO will be light
26. adjust voltage to about 6V power on the indicator enter battery voltage display mode by the way of step15 2 Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 32 KWS CY Operation amp Service Manual 15 3 2 Press down UNIT until CAL 6V is shown adjust voltage to 6V press TARE key to confirm 6V calibration 15 3 3 When CAL 7V is shown adjust voltage to 7V press TARE key to confirm 7V calibration When CV End is shown that means the voltage calibration is completed and then exit to display voltage 15 4 Press SETUP key to return to last menu item press ON OFF key to prepare to exit this mode 16 Display and Set Time 16 1 After entering SETUP mode by press down SETUP key more than 3s using PRINT or ACC key to select MISC TIME item press TARE to display current time 16 2 Time display Format is xx xx xx hh mm ss 24h format 16 3 Press down UNIT more than 3s to enter modification time mode Using HOLD PRINT ACC UNIT TARE keys to modify current time If time of no operation is more than 5s it will automatically exit modification mode 16 4 Press SETUP key to return to last menu item press ON OFF key to prepare to exit this mode 17 Display and Set Date 17 1 After entering SETUP mode by press down SETUP key more than 3s using PRINT or ACC key to select MISC DATE item press TARE to display current time 17 2 Date display Format is xx xx xx yy mm dd 17 3 Press down UNIT more than 3s to e
27. al zero point 100 FS if REGULAR none the max is 2 Zero tracking window AZSM 0 100 2 0 0d no tracking 1 100 0 25d 1 100 s if REGULAR none the max is 4 FILTER Enter digital filter1 threshold O no filter1 FLT1 TH 0 255 40 1 254 filter be used only when vibration in 0 25d 1 254 255 filteri be always used weak FLT1 ST middle Digital filter1 intensity weak middle strong middle Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 12 KWS CY Operation amp Service Manual strong Enter digital filter2 threshold O no filter2 FLT2 TH 0 255 8 1 254 filter2 be used only when vibration in 0 25d 1 254 255 filter2 be always used FLT2 ST 0 255 240 Digital filter2 intensity 0 255 weak to strong FUNG HOLD YES YES Yes No enable disable hold function Operation NO refer to section8 COUNT YES YES Yes No enable disable counting function NO Operations refer to section6 PERGNT NO Percent weighing function is enable or disable 100 1 NO disable 2 100 enable and display NO format is 100 3 100 0 enable and display 100 0 format is 100 0 4 100 00 enable and display format is 100 00 Operations refer to 100 00 section7 BMI YES No Yes No enable disable BMI function NO Operations refer to section8 COMPAR YES YES Yes No enable disable data comparison NO function Operations refer to section9 ACCUMU NO Accumulation M
28. ashed position subtract 1 Menu selection mode To Next item of current menu Aa Change weighing units kg gt lb gt lb oz not be available in Weighing mode press down lt 3s Gi some conditions gt kg Counting Percent mode To enter getting piece weight or unit percentage weight press down lt 3s mode by way of sample or input directly Weighing Counting Percent mode To input compare data for weight pieces or percentage press down gt 3s of high and low limitation UINT Display date or time mode DATA To set current date or time press down gt 3s gt e Display voltage mode i To calibrate input voltage value Select displaying code from no filter filter1 filter2 Rotate the flashed position from left to right Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 9 KWS CY Operation amp Service Manual Weighing Counting Percent Tare function press down lt 3s TARE PRESET E ZERO ON OFF Ey Note Weighing Counting Percent f To input pre set tare weight at selected weight unit press down gt 3s input data mode or Menu selection To confirm input data or current item selection and go to mode next item of current menu or next operation Display ADC code Set or clear tare code Weighing Counting Percent Zero function press down lt 3s Weighing Counting Percent Power off press down gt 3s Input data mode ignore mod
29. ation is same as what in step12 5 2 12 6 After the indicator gets all need data it will calculate and store all calibration parameters into EEPROM display CAL End At last it will re start and go back to original mode 13 Weight Fine tune With this function the user can adjust displayed weight a little and no need standard weight But please note 1 The scale must have been calibrated before this 2 The range of adjustment is current displayed weight x 0 9 1 1 it means the range is about 10 3 The CONFIG REGULA NONE and CONFIG FUNC WT ADJ YES must be set 13 1 To enter this mode turn on indicator after indicator displaying O weight put a load suppose its correct weight is 1230 0Ib onto scale then indicator will display the load s weight say 1234 5 Ib Press down TARE and ZERO at same time until first digit flashes this means indicator has entered into weight fine tune mode 13 2 Use t d gt to input correct weight 1230 0 After confirmed by TARE the active correct weight will be displayed and no any digit will be flashed After this displayed weight will be adjusted by this ratio 1230 0 1234 5 and this ratio will keep active until next modification on it 13 3 To remove effect of this ratio there re two ways 12 3 1 way and 12 3 2 way 13 3 1 Do standard calibration like in 11 CALIBRATION 13 3 2 Move away weight on scale Press ZERO to make 0 displayed Put a
30. be available CONFIG FUNC COMPAR item should set to YES and high and low limitation of pieces should be set correctly according to following steps 6 6 2 In counting working mode Press down DATA key more than 3s to input compare data of high and low 6 6 3 After HIGH being shown 000000 will be displayed use PRINT ACC UNIT key to input high quantity number and press TARE key to confirm Announciator of Hi will be shown in this step Press ZERO key to exit getting piece weight mode and back to counting mode 6 6 4 After Low being shown 000000 will be displayed use PRINT ACC UNIT key to input low quantity number and press TARE key to confirm Announciator of Lo will be shown in this step Press ZERO key to exit getting piece weight mode and back to counting mode NOTE If High number is 0 or is equal or less than low number the comparison will be disabled 6 6 5 After a reasonable limitation is set and compare is be active one of announciators HI OK LO will be lighted and the beeper will sound according to its setting in USER BEEP Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 25 KWS CY Operation amp Service Manual 7 Percent Weighing Mode 7 1 In this mode scale will weigh goods weight on it calculate and display its percentage after the unit percentage weight of goods is obtained NOTE If 100 display format is set to 100 100 0 or 100 00 in CONFIG FUNC PERCEN menu item then the unit pe
31. d from COM2 will COM 2 be executed 4 COM 1 2 command from COM1 Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 17 KWS CY Operation amp Service Manual or COM2 will be executed COM 1 2 Auto off time O not auto power off 1 255 auto A OFF T 0 255 5 power off after 1 255 minutes in this period no operation or no weight changing A OFF MD OFF Auto off mode 1 OFF turn off instrument DSP TIM 2 DSP TIM display time 3 AC TIME turn off AC TIME when only battery is used display time when AC adaptor is used AC TIME If time is displayed and enabled continuously output to COMx the time will be sent out LCD BLT LCD backlight set 1 0 always off 2 1 always on 2 2 press down ZERO UNIT together more 0 255 30 than 3s to turn on or turn off 4 3 255 auto on when key operation or weight changing auto off after 3 255s elapsed LCD CST CST1 8 CST5 LCD contraction level selection SCAL ID SCC 123456 scale s ID number 000000 999999 Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 18 4 4 CAL Submenu KWS CY Operation amp Service Manual CAL SUBMENU1 SUBMENU2 OPTION REMARK CAL ON CAL OFF seal switch is on or off ZERO only do zero point calibration then go to CAL END to end LINE CAL PO line calibration point0 do zero point calibration this point can t be omitted
32. d weight NOTE 2 3 mS TARE only be active when scale is stable 4 TARE weight make indicator to enter displaying NET mode 5 10 Output data When scale is stable press RINT key 5 11 Accumulation Press ACC key to add displayed number to accumulation memories and accumulation times will also add up 1 and then to display accumulation result 5 12 Change Weight UNIT Short press UNIT key to select kg Ib or lb oz unit note under some condition Ib oz is not available Please refer the following tables Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 1 ZERO only be active when scale is stable and weight is in SAZSM setting range Clear TARE weight or ZERO scale make indicator to enter displaying GROSS mode Page 22 Table1 use Kg as primary unit KWS CY Operation amp Service Manual Calibration division value Display division value in different weight unit that can be used kg Lb Lb 0z 0 0001kg 0 0001kg 0 0002Ib Not available 0 001kg 0 001kg 0 002Ib Not available 0 01kg 0 01kg 0 02lb 0 50z 0 1kg 0 1kg 0 2lb Not available 1kg 1kg 2lb Not available 10kg 10kg 20 Ib Not available 0 0002kg 0 0002kg 0 0005 lb Not available 0 002kg 0 002kg 0 005 lb 0 1 oz 0 02kg 0 02kg 0 05 lb 1 oz 0 2kg 0 2kg 0 5 lb Not available 2kg 2kg 5 Ib Not available 20kg 20kg 50 Ib Not available 0 0005kg 0 0005
33. dicator will display PWt Er and go back to counting mode 6 5 2 Obtain piece weight by weighing samples weight which quantity in counting mode press UNIT key When InP PWt is shown use PRINT or ACC key to select SPL PWT press TARE key to weigh samples which quantity is known weight calculate piece weight Press ZERO key to exit getting piece weight mode and back to counting mode 6 5 2 1 When SPL Lo is shown move away any sample on scale and press TARE key to confirm before scale is stable SPL Lo will be flashed After it is stable it will go to next step Press ZERO key to exit getting piece weight mode and back to counting mode 6 5 2 2 When SPL Hi is shown put samples its quantity is known onto the scale Press TARE key to confirm reading weight Before scale is stable SPL Hi will be flashed After it is stable it will go to next step Press ZERO key to exit getting piece weight mode and back to counting mode 6 5 2 3 After INP PCS being shown 000000 will be displayed use PRINT ACC UNIT key to input the quantity of samples and Press TARE key to confirm If the calculated piece weight is less than 0 5d the indicator will display PWt Er and go back to counting mode otherwise after the reasonable piece weight being got the scale will go back to counting mode The got piece weight can be saved after the power off and can be used next time 6 6 Check Counts counts compare in Counting mode 6 6 1 To make counts compare function
34. e Prompt is NO TIME AD CODE YES NO Yes No enable disable output ADC s code NO Prompt is A D CODE BAT VOL YES NO Yes No enable disable output voltage of battery NO Prompt is VOLTAGE STATUS YES VES Yes No enable disable output scale s status NO Prompt is STATUS B LINE NONE LINE1 How many blank lines after strings output NONE no blank line LINE1 2 3 4 there re 1 2 3 INES LINE1 or A Dank lines after strings used for paper feed LINES forward 1 2 3 4 lines LINE4 BEEP KEY YES YES Yes No enable disable beep after a key pressed NO down COMPAR NONE IN LMT 1 NONE not beep 2 L Low beep when lower Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 16 KWS CY Operation amp Service Manual L LOW than low limitation 3 IN LMT beep when in IN LMT range of low and high limitation 4 O HIGH beep E when over high limitation 5 OUT LMT beep O HIGH when lower than low limitation or higher than high OUT LMT limitation HOLD AD H SPD YES NO Yes No enable disable use high speed of A D NO converter after entering HOLD mode HLD MOD NONE HOLD Mode 1 NONE no hold function 2 PS PEAK Positive Peak number Hold mode scale will display and refresh the positive peak PS PEAK value from last zero setting 3 NG PEAK Negative PEAK number Hold mode it s Similar with PS PEAK but negative number is used 4 TOGGLE Press HO
35. e of scale variation being over USER OTHER NLD RNG is more than USER HOLD STB TIM STB ER will be shown press TARE UNIT ACC or PRINT to start averaging again or press HOLD key to exit Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 28 KWS CY Operation amp Service Manual 9 3 5 Auto HOLD When USER HOLD HLD MOD is set to AUTO the hold mode is auto hold mode different subjects can be weighed one after another without pressing any buttons After entering this working mode scale will freeze and display number if scale is stable If scale is not stable but the variation is less than USER HOLD DYN RNG scale will average data in USER HOLD AVGTIM then freeze and display the number Only the weight that is over USER OTHER NLD RNG can be frozen If the held weight is moved away and a new load put on the scale scale will automatically hold new number of load Scale will exit HOLD mode according to the setting of USER HOLD HLD TIM If the time of scale variation being over USER OTHER NLD RNG is more than USER HOLD STB TIM STB ER will be shown press TARE to start averaging again or press HOLD key to exit 9 4 In Positive or Negative Peak HOLD mode the red HOLD for LED version or PEAK and HOLD for LCD version announciator will be lighted in other HOLD mode green HOLD for LED version or HOLD for LCD version announciator will be lighted When HOLD announciator flash the displayed number is live When HOLD
36. ed and the beeper will sound according to its setting in USER BEEP 8 BMI Working Mode 8 1 To BMI working Mode be available CONFIG FUNC BMI menu item should be set to YES 8 2 To enter BMI Working mode In normal weighing mode percent weighing mode or counting mode long press FUNC key one of WEIGH COUNT PERCEN will be shown use ACC or PRINT key to select BMI then press TARE to confirm go to BMI mode 8 3 After scale go to this mode the last stored data HEIGHT will be used first 8 4 If you want to change the height press DATA key to input When CM xxx or IN xxx is shown that means you can use PRINT ACC UNIT keys to input your height in centimeter or inch and use TOTAL to select input height unit in centimeter and inch last press TARE key to confirm and back to BMI working mode Press ON OFF key to exit input data mode and back to BMI working mode The range of height is 50 250cm 19 7 98 4inch and default is 170cm 66 9inch 8 5 In this working mode press ACC key to select weight or BMI number to be displayed when weight is displayed the weight unit can be selected by pressing UNIT key and BMI and weight unit will be displayed at same time 9 HOLD Function 9 1 HOLD function can be used to freeze display number In this mode scale can catch a dynamic number hold a stable number or average a unstable number then HOLD freeze this number temporary for user to watch or record This function can be used in normal we
37. eeeeeeeeeeeeneeeeeeeeeeees 34 21 Serial Port1 2 COM1 2 Receiving TeSt cccccccesssseeeeeeseeseeeeeeees 34 22 Serial Port1 2 COM1 2 Transmitting TeSt c cesssseeeesssseseeeeeeees 34 23 Details about Serial COMMUNICATION ccececeeeeeeeeteneeeeeeeeeeeeeee 34 25 Meaning of Some Symbols and Troubleshooting comoommo 40 26 Display Character es ee eege 43 21 PACKING Sos EE E E EE EEE 44 28 VersioMHIStOIY EE 44 Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 2 KWS CY Operation amp Service Manual KWS CY Indicator Operation Manual Thank you for purchasing the KWS CY indicator Please read all operating instructions carefully before use and keep the following points in mind Avoid lengthy exposure to extreme heat or cold your scale works best when operated at normal room temperature Always allow the scale to acclimate to a normal room temperature before use Allow sufficient warm up time Turn the scale on and wait for a few minutes if possible to give the internal components a chance to stabilize before weighing These electronic scales are precision instruments Do not operate near an in use cell phone radio computer or other electronic device These devices emit RF and can cause unstable scale readings If your scale ever performs poorly try moving the scale to a different room or location Avoid using in condition of heavy vibration and airflow
38. f goods is obtained 6 2 To make counting function be available CONFIG FUNC COUNT item should be set to YES in CONFIG menu 6 3 To enter counting working mode in normal weighing or percent weighing mode long press FUNC key WEIGH PERCEN will be shown use ACC or PRINT key to select COUNT then press TARE to confirm go to parts counting mode Before new piece weight is got the last piece weight will be used 6 4 In counting working mode the function of ZERO TARE PRINT HOLD PRESET TARE ACC SETUP ON OFF are available 6 5 There re two ways to obtain the piece weight 1 input piece weight directly refer operations of step6 5 1 2 weigh samples weight which quantity is known refer operation of step6 5 2 6 5 1 Input piece weight from keypad in counting mode press UNIT key When InP PWt is shown press TARE key to enter input piece weight mode 6 5 1 1 When UNIT KG is shown use PRINT or ACC key to select the unit of piece weight use TARE key to Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 24 KWS CY Operation amp Service Manual confirm and go to next Press ZERO key to exit getting piece weight mode and back to counting mode 6 5 1 2 When last stored piece weight is shown use PRINT ACC UNIT key to input new piece weight press SETUP key more than 3s to input decimal point Press TARE key to confirm and save it then go back to counting mode If the input piece weight is less than 0 5d the in
39. iece weight is error it s too small lt 0 5d The weight on the platform is f PWT ER E f Use a greater weight for the sample too small to define a valid reference weight Unit Percentage Weight is error it s too small the weight of 1 0 1 or PCT ER 0 01 determined by Use a greater weight for the sample CONFIG FUNC PERCNT is less than 0 5d STB ER USER HOLD STB TIM is too short Set USER HOLD STB TIM longer Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 41 KWS CY Operation amp Service Manual USER HOLD HLD RNG is too small or set USER HOLD HLD RNG bigger Service required Check power cord connections Make sure power cord is plugged into the power outlet Check power source Replace batteries Service other failure Power cord not plugged in or properly connected Power outlet not supplying electricity Battery discharged Other failure Not turn on required Cannot zero the display Load on scale exceeds allowable limits Remove load on scale or will not zero when Load on scale is not stable Wait for load to become stable turned on Load cell damage Service required Cannot display weight in Unit not set to enable or d250z when D pins j Bo Enable unit in CONFIG UNITS desired weighing unit unit is lb oz Battery symbol is empty Batteries are discharged Charge batteries or Lo bAt is shown Kilotech Inc USA 877 328 5988 Canada
40. ification Menu selection mode Prepare to exit from current working mode Normally the second function of one key need pressing it down more than 3s Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 10 4 Operation Menu Structure 4 1 Main menu 4 2 CONFIG Submenu KWS CY Operation amp Service Manual 4 CONFIG SubMenu1 SubMenu2 Option Default Remark CFG ON cad CFG OFF seal switch is on or off RESET NO YES NO reset configure parameters to default setting REGULA NONE USA NONE _ Select the standard that the scale will comply CANADA with USA CANADA EUROPE EUROPE 100 Ge at PRIM N TAER oeo PRIM D 0 0001 0 0002 0 0005 0 001 0 002 0 005 0 01 0 02 the division value under primary unit the 0 05 4 division value under second unit is 0 1 automatically determined by indicator according 0 2 to the division value under primary unit 0 5 1 2 5 10 20 50 Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 11 KWS CY Operation amp Service Manual PRIM Ut KG select the primary unit from kg or Ib the second KG unit is the Ib if kg selected as primary unit or kg if lb selected as primary unit the calibration LB standard weight must be in primary unit
41. ighing Mode 13 8 Available Parts Counting Mode 1 13 9 Available Percentage Working Mode 1 13 10 Available Measure Unit kg lb lb 0z PCS 1 13 11 Data Comparison and indicator of High OK and Low is available in Weighing mode Parts Counting i i i j mode and Percentage Working mode 1 13 12 Battery voltage display and charge indicator 1 13 13 Programmable serial output content Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 7 KWS CY Operation amp Service Manual 2 Faceplate EX EX ia of symbol on faceplate 2 1 eer ve 2 3 NET 2 4 TOTAL 25 Ib 26 oz 2 7 kg 28 2 9 Pcs 2 10 BMI 2 11 PEAK 2 12 HOLD 2 13 HI 2 14 OK 2 15 LO 2 16 DON Kilotech Inc turn on when scale is stable turn on when scale is at zero point and the gross weight is 0 turn on when net weight is displaying and the tare weight is not 0 turn off when gross weight is displaying turn on when display data is total times or total of weight pieces or percentage turn on when measure unit is lb or Ib oz turn on when measure unit is oz or lb 0z turn on when measure unit is kg turn on when in percentage weighing mode measure unit is turn on when in counting mode measure unit is pieces turn on when working in BMI mode turn on when in working in HOLD mode and HOLD type is PEAK HOLD turn on and flashing not flashing working HOLD mode and displaying number is isn t live turns on
42. ighing mode counting mode and percent weighing mode After entering HOLD mode the speed of A D converter can be increased to 80Hz if Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 27 KWS CY Operation amp Service Manual USER HOLD AD H SPD is set to YES from original 10Hz for some dynamic weighing applications With the hold function it is possible to weigh restless weighing samples such as live animals moving objects The indicator provides special mode settings to accommodate sample s movements 9 2 To make HOLD function be active the CONFIG FUNC HOLD menu item must be set to YES menu items of USER HOLD HLD MOD AVGTIM HLD TIM DYN RNG STB TIM USER OTHER NLD RNG need be set to reasonable value To speedup sampling of weight set USER HOLD AD H SPD menu item to YES To enter HOLD working mode press down HOLD key when scale works in normal weighing mode counting mode or percent weighing mode 9 3 There re several HOLD mode to freeze display data 1 Positive Peak Number HOLD mode 2 Negative Peak Number HOLD mode 3 Toggle HOLD mode 4 Average HOLD mode 5 Auto HOLD mode The following are details of these HOLD modes 9 3 1 Positive Peak HOLD When USER HOLD HLD MOD is set to PS PEAK the hold mode is positive peak hold mode When scale first enters this working mode it will display the largest positive number that is from the time of zero pint set After entering this working mode
43. ight on and one 350 load cell no optional Bluetooth Module The outline of NIMH batteries package is used Connector between PCB and battery package NIMH battery package J Indicator Rear Cover Ce 1 3 Display 6 digit 7 segment 1 25mm LCDs with 16 annunciators and blue backlight Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 5 KWS CY Operation amp Service Manual 1 4 Keypad 6 push buttons 1 5 Environment 1 5 1 Working temperature 10 C to 40 C 1 5 2 Storage temperature 20 C to 70 C 1 5 3 Humidity 10 to 90 RH without condensation 1 6 Load cell Excitation 1 6 1 Voltage 5Vdc 1 6 2 Max Current 60mA can power 4 350 ohm bridge 1 6 3 Signal connection 4 or 6 lead with sense leads 1 6 4 Max Sensitivity 3mV V to 3mV V 1 6 5 Load cell Wiring only be active when corresponding hardware of analog circuit was installed 1 6 5 1 9 holes socket used Pint Excitation Pin6 Sense lo o ooo y Pin4 Excitation Y Vaage Pin9 Sense Pin2 Pin7 Signal Pin3 Pin8 Signal Sa 5 Pin5 Shield DB9 male Pin 1 6 5 2 4 pins socket used Pint Excitation Pin2 Excitation Pin3 Signal Pin4 Signal 1 7 Communication 1 7 1 Serial port1 Full duplex RS232 1 7 2 Serial port2 USB Virtual RS232 1 7 3 Baud Rate Selectable 1200 2400 4800 9600 19200 38400 bps 1 7 4 Data Output Format 8N1 701 7E1 1 7 5 Protocol
44. kg 0 001 Ib Not available 0 005kg 0 005kg 0 01 Ib 0 2 oz 0 05kg 0 05kg 0 1 Ib 202 0 5kg 0 5kg 1 Ib Not available 5kg 5kg 10 Ib Not available 50kg 50kg Not available Not available Table2 use LB as primary unit Calibration division Display division value in different weight unit that can be used value kg Lb Lb 0z 0 0001Ib Not available 0 0001Ib Not available 0 001 Ib 0 0005 kg 0 001 Ib Not available 0 01 Ib 0 005 kg 0 01 Ib 0 2 oz 0 1 Ib 0 05 kg 0 1 Ib 2 oz 1 Ib 0 5 kg 1 Ib Not available 10 Ib 5 kg 10 Ib Not available 0 0002 Ib 0 0001 kg 0 0002 Ib Not available 0 002 Ib 0 001 kg 0 002 Ib Not available 0 02 lb 0 01 kg 0 02 Ib 0 5 oz 0 2 lb 0 1 kg 0 2 lb Not available 2 lb 1 kg 2 lb Not available 20 Ib 10 kg 20 Ib Not available 0 0005 Ib 0 0002 kg 0 0005 lb Not available 0 005 lb 0 002 kg 0 005 Ib 0 1 oz 0 05 Ib 0 02 kg 0 05 Ib 1 oz 0 5 Ib 0 2 kg 0 5 Ib Not available 5 Ib 2kg 5 Ib Not available 50 Ib 20 kg 50 Ib Not available Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 23 KWS CY Operation amp Service Manual 5 13 Check Weight in weighing mode 5 13 1 To make weight compare function be available CONFIG FUNC COMPAR item should set to YES and high and low limitation of weight should be set correctly according to following steps 5 13 2 In weighing mode Press down DATA key more than 3s to input compare data of high
45. load onto scale a number will be displayed suppose it s 1230 0lb Press down TARE and ZERO at same time until first digit Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 31 KWS CY Operation amp Service Manual flashes this means indicator has entered into weight fine tune mode Press t key the displayed weight will be restored to 1234 5 and then press a to confirm and exit to normal weighing mode 14 Display ADC output Code 14 1 In this mode you can examine the stability of weighing system the increment value of ADC output code corresponding to the loaded weight Note The increment of ADC code for FS weight must be larger or equal to 10 times of selected display division otherwise the calibration cannot be properly completed e g The display division is 0 1kg Load 100kg standard weight on the platform the increment of ADC code should be at least more than 10x100kg 0 1kg 10x1000 10000 In this case the scale can be calibrated Otherwise smaller division needs to be Chosen 2 The variation of ADC code should be small otherwise the calibration cannot properly complete also 14 2 To go to this working mode press down SETUP until CONFIG is shown using PRINT ACC and TARE key to to go to MISC Code item press TARE to enter this mode and display ADC output raw code 14 3 In this mode first press TARE key can set current code as a reference zero and then to display net code pres
46. nter modification date mode Using HOLD PRINT ACC UNIT TARE keys to modify current date If time of no operation is more than 5s it will automatically exit modification mode 17 4 Press SETUP key to return to last menu item press ON OFF key to prepare to exit this mode 18 Display Firmware Version 18 1 Press down SETUP until CONFIG is shown using PRINT or ACC key to select MISC VER item press TARE to display current Version 18 2 Firmware Version display Formatis Vxx yy xx is hardware version yy is software version 18 3 Press SETUP key to return to last menu item press ON OFF key to prepare to exit this mode 19 Display Test 19 1 Press down SETUP more than 3s to enter SETUP mode using PRINT or ACC key to select TEST DISP item press TARE to enter test display mode and all segments will be lighted first 19 2 In this mode every pressing of ACC key will light next segment every pressing of UNIT will light next digit press TARE will automatically light all segments and all digits Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 33 KWS CY Operation amp Service Manual 19 3 Press SETUP key to return to last menu item press ON OFF key to prepare to exit this mode 20 Keyboard and Buzzer Test 20 1 Press down SETUP more than 3s to enter SETUP mode using PRINT or ACC key to select TEST key item press TARE to enter test keypad mode and key will be displayed 20 2 In this mode press a
47. o 9999 when it reaches 9999 it starts over at 0000 After the counter number being displayed it will show CAL OFF or CAL ON according to the status of the sealed calibration switch is OFF or ON If the switch is OFF the following steps can be done but the result will not be saved Press TARE key to go to next step 12 3When ZERO is shown use PRINT or ACC key to select do zero point calibration refer step12 4 or do linearity calibration refer step12 5 12 4When ZERO is selected remove all weight on scale and then press TARE key to confirm the ZERO will Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 30 KWS CY Operation amp Service Manual flash when in catching zero point state After getting reasonable data it automatically goes to step11 6 12 5When LINE is selected press TARE key to confirm to enter linearity calibration 12 5 1 0 weight will be displayed after CAL P being shown remove all weight on scale and then press TARE to confirm to calibrate the zero point the zero weight will flash in catching zero point state After getting the reasonable zero point data the zero weight will become steady and then go to next step 12 5 2 When first default standard weight is displayed after CAL P1 being shown It will be calibrated on standard weight for first point Put corresponding weight more than 10 FS weight onto scale The default standard weight is 100 FS Use HOLD PRINT A
48. ode selection 1 NO no accumulation function 2 MANUAL add up current number to accumulation memory after MANUAL TATOL key is pressed 3 AUTO automatically MANUAL add up current number to accumulation memory after scale is stable and weight is over AUTO NLD RNG WT AD J YES Yes No enable disable weight fine tuning using NO keypad in weighing mode if REGULAR none NO this item is NO The setting will be limited by choice of REGUALA Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 13 4 3 USER Submenu KWS CY Operation amp Service Manual USER Sub Ka SubMenu2 Option Default Remark RESET NO YES NO reset user parameters to default setting COM BAUD RT 1200 2400 4800 9600 9600 selection of com1 s baud rate 19200 38400 BYT FMT 8N1 selection of com1 s byte format 1 8N1 8 data 701 8N1 bits No parity check bit 1 stop bit 2 701 7 data bits 1 Odd parity check bit 1 stop bit 3 7E1 7 7E1 data bits 1 Even parity check bit 1 stop bit OUT MOD CONT Selection com1 output mode 1 CONT continuously output 2 PRINT output PRINT after PRINT key pressed 3 CMD output after a request command is received 4 PRT CMD CMD PRT CMD output after PRINT key pressed or request command received 5 STABLE output after scale is stable PRT CMD Note
49. pacity 25 1 11 CAP ER Parameters about Capacity is not correct 25 1 12 CAL Px Calibration on point x 25 1 13 CAL OFF Calibration Seal Switch is on OFF position 25 1 14 CAL ON Calibration Seal Switch is on ON position 25 1 15 CAL Er Calibration error maybe input data or loaded weight is incorrect unstable un linear 25 1 16 CAL End Calibration is end 25 1 17 OFF Power OFF the indicator 25 1 18 STB ER Unstable time is lager than setting of USER OTHER NLD RNG 25 1 19 AC nx Accumulation times is xxxx 25 1 20 PR TARE To Preset TARE weight 25 1 21 COMP To go to input COMPARE data mode 25 1 22HIGH To input HIGH limitation data of Comparison 25 1 23LOW To input LOW limitation data of Comparison 25 1 24 SPL Lo Sample load weight of low point 25 1 25 SPL HI Sample load weight of high point 25 1 26 SPL PWT Sample goods weight to calculate piece weight 25 1 27 INP PCS input pieces number of weighted goods 25 1 28 UNIT KG Unit kg is selected 25 1 29 UNIT LB Unit lb is selected 25 1 30 PWT ER Piece weight is error it s too small lt 0 5d 25 1 31 SPL PCT Sample goods weight to calculate 25 1 32 INP PCT input percentage of weighted goods 25 1 33 PCT ER Unit Percentage Weight is too small lt 0 5d Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT
50. power off the scale just like press down the ON OFF key to turn off the scale 23 6 1 8 Command all others Response Unrecognized command lt LF gt lt CR gt lt ETX gt 23 6 2 Summary of Command and Response Command Response ASCII HEX Read scale weight GXLF gt AA44AA0U Us U U Us lt CR gt lt LF gt HH Hi lt CR gt lt ETX gt over capacity 2xLF gt U U U3U Us lt CR gt lt LF gt HH Hi lt CR gt lt ETX gt under capacity W lt CR gt 570d 3LF gt UUs Us UsUs lt CR gt lt LF gt H H2H3 Ha lt CR gt lt ETX gt zero point error 4xLF gt lt p gt W W2W3W 4Ws lt dp gt W U U2U3U4Us lt CR gt lt LF gt H H2H3H4 lt CR gt lt ETX gt normal data S lt CR gt 53 0d lt LF gt H H2H3H lt CR gt lt ETX gt read scale status Z lt CR gt 5a 0d lt LF gt H H2H3H lt CR gt lt ETX gt simulate ZERO key T lt CR gt 540d lt LF gt H H2H3H4 lt CR gt lt ETX gt simulate TARE key U lt CR gt 55 0d lt LF gt Us U3 U Us lt CR gt lt LF gt H H2H3H4 lt CR gt lt ETX gt simulate UNIT key L lt CR gt 4c Od lt LF gt H HsH3H lt CR gt lt ETX gt simulate HOLD key X lt CR gt 58 Od power off the scale simulate OFF key others lt LF gt lt CR gt lt ETX gt Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 37 KWS CY Operation amp Service Manual 23 7 Communication when USER COM1 2 LAYOUT is set to MULTIPLE 23 7 1 Ou
51. rcentage weight is the weight of 1 0 1 or 0 01 7 2 To make percent weighing function be available CONFIG FUNC PERCEN menu item shouldn t be set to NONE 7 3 To enter percent weighing mode in normal weighing or counting mode long press FUNC key WEIGH COUNT will be shown use ACC or PRINT key to select PERCEN then press TARE to confirm go to percent weighing mode Before new unit percentage weight is got the last unit percentage weight will be used 7 4 In percent weighing mode the function of ZERO TARE PRINT HOLD PRESET TARE ACC SETUP ON OFF are available 7 5 To obtain the unit percentage weight there re two ways 1 input weight and its percentage then scale calculates the unit percentage weight refer operations of step7 5 1 2 weigh samples weight which percentage is known refer operation of step7 5 2 7 5 1 Input weight and its percentage from keypad and calculate unit percentage weight in percent weighing mode press UNIT key When InP Pct is shown press TARE key to enter this mode 7 5 1 1 Before input weight use PRINT or ACC key to select the percentage from 1 2 5 10 20 50 and 100 this percentage is corresponding to the weight you will input in following steps 7 5 1 2 When UNIT KG is shown use PRINT or ACC key to select the unit of input weight use TARE key to confirm and go to next Press ZERO key to exit and back to percent weighing mode 7 5 1 3 When last stored unit percentage weight data is
52. s TARE again to clear this reference and display gross code In display net code mode press ACC key to select net or gross code to display not clear the reference code 14 4 In this mode press UNIT key to select displaying code that has been filtered by no filter filter1 or filter1 and filter2 and corresponding announciator Lo OK HI will be lighted 14 5 Press SETUP key to return to last menu item press ON OFF key to prepare to exit this mode 15 Display and Calibrate Power Voltage 15 1 In this mode you can examine the voltage of battery or you can examine the voltage that regulated out from AC adaptor when no battery is used you also can calibrate the displayed voltage and set the voltage value of low battery point Note 1 The end customer normally no need to set the value of low battery and full charged voltage calibrate the displayed voltage these have been done in factory 2 The normal displaying voltage is 5 6V 7 6V 15 2 To go to this working mode press down SETUP until CONFIG is shown using PRINT ACC and TARE key to to go to MISC VoL item press TARE to enter this mode and display battery voltage 15 3 If the voltage is sure not correct to calibrate the voltage according to following steps 15 3 1 Prepare a DC power supply which output voltage can be adjusted from 5V to 8V output current must be larger than 0 5A Power off the indicator move away AC adaptor Connect this DC power to battery connector on main board
53. section 5 7 Preset tare weight long press PRESET key Pr Tare will show and the TARE announciator flashes it means itis in preset TARE weight mode use t I lt _ to input tare weight and its unit is same as the unit that it used before there s no limitation to preset tare weight but it should bigger than zero After input a tare weight NET announciator will be lighted Note this indicator can only save one tare weight the new tare weight will automatically replace the old one Also please refer the ZERO and TARE limitations in 5 9 section 5 8 Clear tare weight remove any weight on platform wait till the scale is stable short press TARE key please refer the ZERO and TARE limitations in 5 9section Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 21 KWS CY Operation amp Service Manual 5 9 Limitation to ZERO and TARE operation under different conditions Standard WE e Data in TARE EE platform memory unit Tare key Zero key lt 0 no No action yes Clear the tared weight USA Se Zero gt 0 Tare Yes p no No action Gana Yes Clear the tared weight Se dg No Tare Yes No action No No action Zero Eneee E Yes Clear the tared weight wae Sea No zero CR Yes Tare zero and clear the tared weight No No action Zero pone Se SS yes Clear the tared weight es SE Europe No zero Zo Tare zero and clear the ee tare
54. ss than low number the comparison will be disabled 10 6 After a reasonable limitation is set and compare function is be active one of announciators HI OK LO will be lighted and the beeper will sound according to its setting in USER BEEP 10 7 For details please refer to section of section5 13 6 6 and 7 6 11 Accumulation Kilotech Inc USA 877 328 5988 Canada 800 694 4445 Service EXT 6023 or 6026 Page 29 KWS CY Operation amp Service Manual 11 1 Accumulation function can be used in normal weighing mode counting mode and percent weighing mode When this function is enabled you can accumulate current net weight piece and percentage Note only the load on scale is larger than USER OTHER NLD RNG the displayed positive number can be added up The accumulation times and total can be displayed or printed 11 2 To make data accumulation function be available CONFIG FUNC ACCUMU menu item should set to MANUAL or AUTO Following are details 11 3 When CONFIG FUNC ACCUMU is set to MANUAL the stable and positive displayed net weight must be larger than USER OTHER NLD RNG piece or percentage can be accumulated by long pressing TOTAL key and indicator will display accumulation times first and then display total of number To avoid repeating accumulation for same load one load only can be accumulated once So before a new load put onto the scale the original load should be removed and let load on scale be smaller than USER OTHER NLD RNG
55. the division number under second unit the max SECND N 100 150 000 3000 is 1 5 PRIM N and if REGULAR none the max is 10 000 10N DSP NO Display weight at 10 times division number NO under primary unit if REGULAR none no this YES item units that can use UNIT key to select O kg 1 Ib 2 Ib 0z 3 kg lb 4 kg lb 0z 5 Ib b oz UNITS 0 6 6 6 kg lb lb oz refer to sectioon5 12 for some limitation Check motion window 1 255 0 25d MOTION 1 255 4 1 255 if REGULAR none the max is 12 over load display limitation O FS 9d OVER LD 0 100 0 1 100 101 FS 200 ES if REGULAR none the max is 10 ZRO PNT Si Initial zero power on zero point range O no a limitation 1 100 calibration zero point IZSM 0 100 10 1 FS calibration zero point 100 FS If REGULAR none the max is 10 IN IZSM WEIGHT Choose which weight as current initial zero point when current weight is in IZSM range CAL ZRO WEIGHT current weight CAL ZRO WEIGHT calibration zero LAST Z T switch off zero and tare LAST Z T If REGULAR none the value is fixed on WEIGHT OV IZSM DSP OVR Choose which weight as current initial zero E point when current weight is over IZSM range WEIGHT DSP OVR display initial zero is over DSP OVR WEIGHT current weight CAL ZRO CAL ZRO i calibration zero LAST Z T switch off zero and tare LAST Z T If REGULAR none the value is fixed on DSP OVR Zero key range O no limitation 1 100 initial SAZSM 0 100 2 zero point 1 FS initi
56. tput string frame lt LF gt lt Prompt gt lt p gt W W 2W3W4Ws lt Dp gt We U1U2 U3 U Us lt CR gt Sites Line number and content are determined by setting of USER OUT1 2 xxxx lt LF gt lt Prompt gt H H2H3 H4 lt CR gt USER OUT1 2 STATUS is set to YES lt LF gt lt CR gt USER OUT1 2 LINE is set to LINE1 2 3 4 widens The number of blank lines is determined by USER OUT1 2 LINE setting lt ETX gt Last byte of string frame 23 7 2 Caution 1 The decimal point position is determined by CONFIG PRIM D 2 The unit position and bytes is determined by which current unit is used 3 The details of lt Prompt gt refer to the content in 4 3USER Submenu 4 In hold mode if ADC conversion speed is set high speed 80Hz and USER COM1 2 LAYOUT is set to MULTIPLE and many contents are selected to output the output contents from COM1 or COM2 may not catch up with the data processed in indicator So if you want to watch real time data you need to select fewer output contents and set higher baud rate for COM1 or 2 23 7 3 Examples of some layout when USER OUT1 2 xxxx is set to YES USER COM2 EN ADDR No 23 7 3 1 In weighing mode SCALE ID 123456 GROSS 123lb 4 560z TARE 11lb 2 220z NET 112lb 2 340z ACC N 8 TOTAL 789lb 15 20z DATE 2011 06 12 TIME 12 34 56 A D CODE 1234567 VOLTAGE 6 7V STATUS bpq2 23 7 3 2 In counting mode SCALE ID 123456 GROSS 1234 55kg TARE 12 15kg NET 1222 40kg QUANTITY

Download Pdf Manuals

Related Search

Related Contents

  FCC 47 CFR PART 15 SUBPART B TEST REPORT  390KB  Canon MAXIFY iB4050  平成 26年度版 浄化槽普及促進ハンドブック  Fire Sense 60351 Installation Guide  F3X36 Series Router User Manual - Four  User`s Manual PowerPanel Business Edition  Rheem Classic Plus Series: 80% AFUE Downflow Warranty Information  Kenwood KNA-DV2200 GPS Receiver User Manual  

Copyright © All rights reserved. Failed to retrieve file