Scarifier BMP-335 EHY and GHY
Contents
1. _ a al Y 4 Ze A In 3 nn an ur S N its NIB Y gt di a E AS BER ee e 4 A NED Kam GIES i Apo 5 4 7 e le ARGS P y 3 bi E l t d a Lf y a z gine he Operating manual BMP 335 EHY amp GHY BMP 335 EHY amp GHY Version 1 0 Operating manual info blastrac eu www blastrac com EBLASTRAC Operating manual BMP 335 EHY amp GHY 2 12 EC DECLARATION OF CONFORMITY in accordance with Appendix II sub A of Directive 98 37 EC BLASTRAC B V Utrechthaven 12 NL 3433 PN NIEUWEGEIN Tel 0031 0 30 601 88 66 Fax 0031 0 30 601 83 33 Info Blastrac nl The Netherlands Declare under our sole responsibility that the machine as described below Conforms with the Health and Safety requirements of the European Directive of the machine Safety In case of changes to the machine without our written authorization this declaration loses its validity Model BLASTRAC BMP 335YHY amp GHY Serial number 1 satisfies the conditions set out in the Machine Directive Directive 98 37 EC Low voltage directive 73 23 CEE as last amended EMC directive 89 336 CEE as last amended 2 satisfies the following harmonized standards NEN EN 349 NEN EN 418 NEN EN 294 and NEN EN 60204 Nieuwegein 01 12 2008 info blastrac eu www blastrac com EBLASTRAC Operating manual BMP 335 EHY amp GHY 3 12 Table of contents EC Declaration of Conformity 02 1 Introduction 04 2 Machine descripti2. accordance with the overall power consumption of the machine Electrical cables must be rolled entirely off of the reels Any damage to electric cables is not permitted Use an electrical power supply connection with earth connection Checkpoints of machine safety Check if The safety functions and operating functions work correct The drum is in good condition The drum is assembled as shown in the service manual There is not any damage to the hydraulic components on the machine There are not any loose nuts or bolts There is not any damage to the dust hose and if it is connected correctly Check when using non symmetric cutters if the direction of turning is like figure below Removing the drum Loosen the bolts of the side plate and remove the side plate Pull the drum from the axle and support the drum Mounting the drum Clean the hexagon axle and lubricate this over the whole length Slide the drum over the axle until it will not go any further Mount the side plate A side plate which is incorrectly mounted or mounted with force will shorten the lifetime of the drum bearings Never use the machine without a side plate or with an incorrect mounted side plate info blastrac eu www blastrac com EBLASTRAC Operating manual BMP 335 EHY amp GHY 9 12 5 Operating During operating the BMP 335 the following additional safety instructions must be followed closely Befo
3. c United Kingdom Unit 2 Outgang Lane Dinnington Sheffield South Yorkshire GB S25 3QU England Tel 0044 0 1909 569 118 Fax 0044 0 1909 567 570 info blastrac co uk Blastrac France ZI 29 Avenue des Temps Modernes F 86360 Chasseneuil du Poitou Tel 0033 0 5 49 00 49 20 Fax 0033 0 5 49 00 49 21 info blastrac fr Blastrac Spain Calle Copernico 16 Nave 2 E 28820 Coslada Tel 0034 91 660 10 65 Fax 0034 91 672 72 11 info blastrac com es Blastrac Germany Mathias Br ggen Stra e 144 D 50829 K ln Ossendorf Tel 0049 0 221 70 90 32 0 Fax 0049 0 221 70 90 32 22 info blastrac de Blastrac Poland Golina Dworcowa 47a 63 200 Jarocin Tel 0048 62 740 40 27 Fax 0048 62 740 40 27 info blastrac pl info blastrac eu www blastrac com 12
4. e or ramp when the treadle is in upwards position info blastrac eu www blastrac com EBLASTRAC Operating manual BMP 335 EHY amp GHY 7 12 The following sticker is placed on the machine Meanings of these symbols are Ear protection is obliged Safety glasses with lateral protection are obliged CE mark on this machine Safety shoes obliged Consult the manual before operating the machine Personnel must tie back long hair and not wear loose clothing or jewellery including rings Wear gloves and dust mask during operating the machine Safety instructions Pull out the main plug when changing the drum or during repairing the machine Make sure the machine is clean and that the handgrips are dry and free of grease and oil The dustbin of the dust collector must be emptied regularly Pay attention to the environment regulations The weight of the BMP 335 is 405 kilogram Use preferably appropriate appliances as a lift or crane Use the existing lifting points to lift the machine info blastrac eu www blastrac com EBLASTRAC Operating manual BMP 335 EHY amp GHY 8 12 4 Initial operation Before using the machine it is of great importance to inspect the machine It is not permitted to use the machine if the machine safety is not according the checkpoints below Checkpoints of electrical safety Use only extension cables for extending the main cable that are sized and marked in
5. ings To make non slip surfaces The force of impact of a cutter is controlled by the depth adjustment With the right depth adjustment the best performance is obtained to give a desired result With a suitable Blastrac dust collector work can be carried out without causing dust in the work area this raises the life span of the machine and helps the health of the personnel info blastrac eu www blastrac com EBLASTRAC Operating manual BMP 335 EHY amp GHY 5 12 BMP 335 EHY _ BMP 33SCGHY 1 readle of drive system readle of drive system 3 Quick lift lever Quick lift lever 4 Handwheel working depth Handwheel working depth 8 Electrical panel Hydraulic pump housing 9 Hydraulic pump housing Diesel motor fof fStartcord info blastrac eu www blastrac com EBLASTRAC Operating manual BMP 335 EHY amp GHY 6 12 3 Safety Before operating the machine the personnel must be familiar with the safety instructions given in this manual Keep this manual near to the machine so it can always be consulted Safety precautions The surface to be treated must be swept clean to remove stones Screws etc Never use the machine when the surface is not clear and if there is a risk of tripping Make sure there is not any water on the surface to be treated Don t get disturbed during the activities Remove any trailing electrical cables and or dust hoses from the surface to be treated Always switch on the dust co
6. llector Safety regulations Persons who are not operating the machine must not be permitted to stay in the surrounding area of the machine Don t change anything on the machine Always use cables which are approved and safety earthed including extension cables The machine is always equipped with an earthed connection do not change this and use always earthed cables with an earthed plug Connect the main power supply cable to an installation with an earth leakage circuit breaker Inspect and test the electrical components regularly The electrical components have to satisfy to the requirements which apply to these components Always call a skilled electrician or your distributor when you have questions about the safety of the electrical components Work on electrical equipment or operating materials may only be undertaken by a skilled electrician or by trained persons under the guidance and supervision of a skilled electrician as well as in accordance with the electrical engineering regulations Pull out the main plug during inspections and repairing on the machine Never operate the machine when the surface is wet Never use the machine in the rain It is possible to transport the machine without electrical power by pushing up the treadle pos 1 page 5 The drive wheels are declutched of the drive motors now Be sure that the floor is flat because the machine is uncontrolled now It is very dangerous to drive the machine on a grad
7. on 04 3 Safety 06 Safety precautions Safety regulations Safety instructions 4 Initial operation 08 Checkpoints of machine safety Removing the drum Mounting the drum 5 Operating 09 6 Maintenance 10 7 Technical data 11 Contact 12 info blastrac eu www blastrac com EBLASTRAC Operating manual BMP 335 EHY amp GHY 4 12 1 Introduction It is important that all persons who are working with or maintaining this machine must read the manual carefully and understand it fully Keep this manual near to the machine to enable it be referred to at any time Only authorized and trained personnel may operate this machine 2 Machine description The Blastrac scarifier BMP 335 can be supplied with a 400 volt electric motor EHY or with a combustion engine GHY The scarifier can be used on almost any surface concrete asphalt stone and steel to roughen up existing surfaces and removing coatings The drum of the scarifiers revolves at 1000 revolutions per minute RPM The depth of scarifying can be adjusted by the fine adjustment control at the front of the machine by this means it is possible to treat the surface with light or heavy cuts as is required Application The scarifier is a very versatile machine and with the appropriate cutters it may be used for the following applications To roughen concrete To clean most horizontal surfaces To remove coatings To corrugate concrete surfaces To remove road mark
8. re starting up Make sure that the drum doesn t hit the ground The quick lift lever must be in upper position and the fine adjustment must be turned up Connect the scarifier and the dust collector with the dust hose Make sure there is a good and airtight connection Connect the scarifier and the dust collector with the power supply Make sure the right connection is available for the machines only BMP 335EHY Procedure to start work Turn on the dust collector Put the cord of the dead man switch around the left wrist Start the machine by pushing the button scarify motor ON BMP 335EHY or by pulling the start cord of the diesel motor BMP 335GHY Check if the drum turns the right direction Only BMP 335EHY Slowly let down the quick lift lever slowly Turn the fine adjustment clockwise till the desired scarifying depth is reached Switch off the machine Pull the quick lift lever up and turn the fine adjustment till the drum does not hit the ground anymore Push the red button BMP 335EHY or push down the START RUN knob BMP 335 GHY see picture below Switch off the dust collector Disconnect the power supply Pay attention that all twisting and turning machine parts have reached a standstill before inspection or maintenance duties are carried out START RUN STOP info blastrac eu www blastrac com EBLASTRAC Operating manual BMP 335 EHY amp GHY 10 12 6 Maintenance P
9. revent premature wear by keeping the machine as dust free as possible Clean the machine for this reason regularly with a dust collector Clean the machine every day with air and non aggressive materials Never use a high pressure water cleaner to clean the machine Store the cleaned and dry machine in a dry and humid free room Protect the electrical motor from moisture heat dust and mechanical shocks All repair work must to be done by qualified Blastrac personnel this to guarantee a safe and reliable machine au guarantee on the machine is expired when Non original Blastrac parts and cutters have been used Repair work is not done by qualified Blastrac personnel Changes add on s or conversions are undertaken without written permission of Blastrac BV info blastrac eu www blastrac com 10 EBLASTRAC Operating manual BMP 335 EHY amp GHY 11 12 7 Technical data BMP 335EHY BMP 335GHY Power 12 1 kW 7 5kW consumption Rotation speed 1000 min 1000 min drum Length 1400 mm 1400 mm Weight 405 kg inc drum 405 kg inc drum Noise level Up to 108dB A Up to 108dB A Dust hose 075 mm 075 mm connection Height 1075 mm 1075 mm info blastrac eu www blastrac com 11 EBLASTRAC Operating manual BMP 335 EHY amp GHY 12 12 HEADQUARTER Blastrac BV The Netherlands Utrechthaven 12 NL 3433 PN Nieuwegein Tel 0031 0 30 601 88 66 Fax 0031 0 30 601 83 33 info blastrac nl Blastra
Download Pdf Manuals
Related Search