Service Manual – TXSG Server
Contents
1. WILBUR Curtis Co INC Service Manual TXSG Server BREWING INTO THE TXSG SERVER 1 Make sure the control panel screen reads READY TO BREW 2 Place a clean and empty server centered under the brew cone of your coffee brewer 3 Remove the top cap from the lid 4 Fill brew cone with the correct measure of ground coffee 5 Select the BREW button that matches the brew volume Press the BREW button to start the brew 6 Allow coffee in the brew cone to completely drip out before removing the coffee server Models e TXSG0101S600 e TXSG1501S600 e TXSG0101S200 yn WARNING Thermopro servers may be heavy when filled e TXSG1501S200 Care must be taken when transporting to avoid dropping or spilling SERVICING THE THERMOPRO SERVER 1 Completely drain the unit of any coffee 2 Allow server to cool 3 Unscrew and remove the lid and tube assembly REPLACING THE GAUGE GLASS The gauge glass can be removed for maintenance and cleaning Refer to the illustration on page three 3 for assembly sequence 1 Unscrew the vented cap plug from the top of the gauge glass shield 2 Carefully lift out the gauge glass tube from the shield and scrub inside the glass with a tube cleaning brush and mild detergent solution Inspect the glass tube for cracks or chips If broken carefully remove all traces of glass and insert a new glass tube 3 Check the top and bottom washers Clean the washers Make sure they are not leaking R2. Coffee Server Precautions Do not immerse coffee server in water s L Do not place in dishwasher Do not use harsh powders or cleansers containing chlorine Do not use a wire brush or pot scour to clean inside liner Illustrated Parts List All parts are common between the 1 gallon and 1 2 gallon servers except where indicated by TXSG15 and TXSG01 INDEX Ne PART Ne DESCRIPTION INDEX Ne PART Ne DESCRIPTION 1 WC 37387 KIT CAP TETHER amp SCREW TXSG 15 WC 64079 GUARD FAUCET TXSG ZINC 2 WC 56025 LID ASSY TXSG15 16 WC 1906 C RING 917 x 760 x 090 2A WC 56024 LID ASSY TXSG01 17 WC 1905 NUT WING PLASTIC 1 1 32 14UNF 3 WC 1949 CAP SHIELD WITH VENT PLASTIC 18 WC 4320 O RING 2 I D 4 WC 2005 WASHER SHIELD CAP 1 8 19 WC 3705 KIT FAUCET REPAIR 9 WC 2027 GLASS GAUGE 10 TXSG15 20 WC 56020 BASE ASSY SERVER STRAIGHT SIDE 5A WC 2025 GLASS GAUGE 8 TXSG01 20A WC 56013 BASE ASSY SERVER OPTIONAL 5B WC 37396 KIT GLASS GAUGE 10 3PK TXSG15 21 WC 61689 DRIP TRAY ASSEMBLY TLXS 6 WC 56028 TOP SERVER THREADED BLK 22 WC 43091 CLAMP WIRE HOSE 7 WC 2063K KIT BRACKET GAUGE GLASS RING 23 WC 2456 ELBOW SILICONE STRT SIDE SRV 8 WC 2012 101 SHIELD GAUGE GLASS 10 TXSG15 24 WC 4281 NUT 2 NPSM PLASTIC 8A WC 2010 101 SHIELD GAUGE GLASS 8 TXSG01 25 WC 58262 COVER BOTTOM WHITE PLASTIC 9 WC 56030 BOTTOM PLASTIC BLACK SERVER 26 WC 37395 KIT GAUGE ASSY 10 BLK TXSG15 10 WC 32004 BALL PLASTIC RESTRICTOR TXS 27 WC 2004 10
3. 1 SHIELD BASE GAGE BLACK OLD UNITS 11 WC 2006 WASHER 188 ID X 188 THK BTM 28 WC 29082 FITTING 14 NPSF ASSY OLD UNITS 12 WC 1951 NUT FLANGED PLASTIC 28A WC 29082K KIT FIT W SILICONE WASH OLD UNITS 13 WC 1938 103K KIT SHNK NUT amp INST TXSG 1GAL amp 1 5GAL 29 WC 36076 BRUSH GAUGE GLASS 13A WC 1938 SHANK PLASTIC OLD UNITS 30 WC 38281 LABEL DECAF 14 WC 1841 FAUCET ESP BLACK LOCKING Z Illustrated Parts Rough In Drawings TXSG15 TXSG01 Product Warranty Information Wilbur Curtis Co Inc certifies that its products are free from defects in material and workmanship under normal use The following limited warranties and conditions apply 1 year from the original date of purchase RETURN MERCHANDISE AUTHORIZATION All claims under this warranty must be submitted to the Wilbur Curtis Co Inc Techni cal Support Department prior to performing any repair work or return of this equipment to the factory All returned equipment must be repackaged properly in the original carton No units will be accepted if they are damaged in transit due to improper packaging NO UNITS OR PARTS WILL BE ACCEPTED WITHOUT A RETURN MERCHANDISE AUTHORIZATION RMA RMA NUMBER MUST BE MARKED ON THE CARTON
4. OR SHIPPING LABEL All in warranty service calls must be performed by an authorized service agent Call the Wilbur Curtis Co Inc Technical Support Department to find an agent near you m Ml TAI 7 Q AR AADA rov M ECN 16647 8 26 15 12 0 rev M WILBUR CURTIS CO INC we 6913 Acco St Montebello CA 90640 5403 USA Phone 800 421 6150 Fax 323 837 2410 Technical Support Phone 800 995 0417 M F 5 30 a m 4 00 p m PST Email techsupport wilburcurtis com Printed in U S A 8 2015 F 3595 Rev M
5. eplace if necessary 4 With the sight glass seated in the gauge glass shield thread the cap plug onto the top of the shield Do not overtighten REMOVING THE BASE amp BOTTOM COVER To replace the silicone elbow fitting for repair or cleaning 1 Remove the base assembly Press down on the slide tab in back of the stand and lift off the server 2 Turn the server upside down and take off the plastic bottom cover revealing the silicone elbow fitting 3 Remove the wire hose clamps by squeezing the wire ears together While holding the clamp open loosen the soft silicone elbow from the liner drain pipe and the faucet shank and pull out elbow 4 Check for leaks and replace with a new elbow if necessary 5 Reverse these steps to assemble REMOVING THE FAUCET The faucet will require periodic cleaning and maintenance 1 Remove the faucet from the body of the server Unscrew the large nut holding the faucet to the shank to take off the faucet 2 Disassemble the faucet Unscrew the bonnet from the body of the faucet 3 Remove the faucet handle by pressing inward on the seat cup see photo at right then unhooking the handle from the center shaft UNSCREW BONNET 4 The seat cup center shaft and spring will now separate from the bonnet Clean these parts with a mild aya detergent solution 5 While you have these parts disassembled for cleaning check the condition of the seat cup Make sure the faucet spring is free of corrosion Re
6. place these parts with repair kit if necessary item 19 page 3 ASSEMBLY Assemble the unit by reversing the steps for disassembly Finger tighten wing nut onto faucet Make sure clamps are fastened properly and silicone fittings are in good condition Once assembled check for leaks around the fitting and faucet FOR THE LATEST SPECIFICATION INFORMATION GO TO WWW WILBURCURTIS COM l Cleaning Instructions In a container mix a mild detergent and warm water solution for cleaning the coffee server Discard old coffee from the coffee server Remove and clean the lid Clean inside the coffee server with a sponge brush soaked in detergent solution O A O N gt An easy way to remove mineral deposits from the brew cone and the coffee server is to use a pouch or tablet cleaner amp a Place two tablets or one pouch refer to manufacturers recommendation into the brew cone b Place the empty coffee server onto the brew deck c Start a coffee brew cycle by pressing the Brew button on the electronic controller d When the brew cycle has finished allow the cleaning solution to sit in the coffee server for a few minutes then empty the coffee server 6 Wipe the exterior surfaces with a sponge moistened with the detergent solution Wipe LENER CLEANER off coffee spots or stains 7 Rinse the brew cone and coffee server with running water 8 Dry the parts and return them to the coffee brewer TXSG
Download Pdf Manuals
Related Search