manual as pdf
Contents
1. of tape into the channel of the tire bed Tubeless Rim Tape 36 3 Apply tension to the tape by rotating the wheel away from you while rapidly shaking the tape from side to side about 2 3 inches 5 8 cm This will seat the tape into the channel and keep it centered in the rim NOTICE The tubless tape must be seated into the channel to create an adequate seal If the tape is not seated into the channel the tire may leak air 4 Continue the process of rotating the wheel and shaking the tape side to side while keeping an even tension on the tape roll until the tape meets the beginning edge of tape from step 2 Overlap the beginning edge with another 12 inches 31 cm of tape to the wheel 5 Cut the tape Use your fingers or a tire lever to press the leading edge of tape against the rim This will help prevent sealant from getting under the tape Tubeless Rim Tape Installation 37 Valve Stem Installation 2 Shine a flashlight through the rim to illuminate the valve stem hole Use a small knife to cut the tape from the valve stem hole Remove the nut and o ring from the valve stem Install the valve stem into rim Install o ring onto the valve stem Install nut onto valve stem and o ring with the recessed area toward rim Press the valve stem into the channel and hand tighten the nut Valve Stem Installation 38 Wheel Build amp Spoke Replacement Replacement Parts For part numbers2. Installation Cylinder with a soft face mallet until the bearing is firmly seated into the bearing pocket Short Installation Cylinder To install the ring nut first install the Ring Nut Installation Tool into a vise so that the teeth are level with the top of the vise Ring Nut Installation Tool 2 Place the ring nut onto the Ring Nut Installation Tool with the recessed edge facing up Apply a light layer of grease to the threads of the ring nut Place the the shim ring on top of the ring nut ROAM 60 50 amp RAIL 50 Rear Hub Bearing Replacement 30 22 Insert the axle into the Ring Nut Installation Tool Carefully turn the wheel clockwise to thread the ring nut into the drive side of the hub Do not overtighten the ring nut NOTICE After the ring nut has engaged the threads inside the hub you will need to raise the Ring Nut Installation Tool in the vise to prevent the vise from scratching the hub shell 23 Install one of the Short Installation Cylinders into a vise Install the disc brake end of the axle into the Short Installation Cylinder Short Installation Cylinder 24 Place the rotor seal onto the Seal Installation Tool with the rubber seal facing the tool Place the tool onto the axle with the rotor seal facing toward the hub NOTICE If the rotor seal shows any signs of damage it must be replaced with a new rotor seal Seal Installation Tool 25 Place a Long Installation Tool onto the axle Strike th
3. axle and into the hub Strike the tool with a soft face mallet until the bearing is firmly seated into the bearing pocket Periodically check bearing alignment in the hub Large Diameter Hub Tool Check the axle for play by pushing and pulling it in the hub If any play is detected repeat steps 12 16 18 Apply a light layer of grease to each bearing face Use a rag or paper towel to remove any grease from the ends of the axle ROAM 50 Front Hub Bearing Replacement 22 19 Press the end caps onto the hub by hand NOTICE The tall end cap is installed on the disc brake side of the hub ROAM 50 Front Hub Bearing Replacement 23 ROAM 60 50 amp RAIL 50 Rear Wheel Service We recommend that you have your SRAM wheels serviced by a qualified bicycle mechanic Servicing SRAM products requires knowledge of bicycle components as well as the special parts and tools used for service For exploded diagram and part number information please refer to the Spare Parts Catalog available on our web site at www sram com For order information please contact your local SRAM distributor or dealer Information contained in this publication is subject to change at any time without prior notice For the latest technical information please visit our website at sram com Your product s appearance may differ from the pictures diagrams contained in this publication Parts and Tools Nitrile gloves Torque wrench Apron Soft face
4. e Foam rings e Chains e Bottomout pads Motors e Rear shock mounting hardware Sprockets e Bearings e Batteries and main seals e Cassettes e Bearing races e Upper tubes stanchions e Shifter and brake cables inner Pawls and outer Transmission gears Notwithstanding anything else set forth herein this warranty is limited to one year for all electronic and electronic related components including motors controllers battery packs wiring harnesses switches and chargers The battery pack and charger warranty does not include damage from power surges use of improper charger improper maintenance or such other misuse This warranty shall not cover damages caused by the use of parts of different manufacturers This warranty shall not cover damages caused by the use of parts that are not compatible suitable and or authorised by SRAM for use with SRAM components This warranty shall not cover damages resulting from commercial rental use TABLE OF CONTENTS ROAM 60 amp RAIL 50 Front Wheel Serve id 5 BOLES o TOO del ere A A A Se D er rats 5 ROAM GO Q RAI SO End Capi Replace Mentiras li a id de seo da ld a ee en eu 6 ROAM 60 amp RAIL 50 Front Hub Bearing Replace Menta temen nyament temen 10 ROAM 50 Front Whe l Service ii A A a AA Anaa aaa da 16 Parts and IO OS et ee E a td eo a nd 16 ROAM SOENG CoD Replace MER O a da DR NA ns 17 ROAM SON Front UD Bearno Replace mentada a 18 ROAM 60 50 8 RAIL 50 Rear Wheel Service ccsccceccc
5. mallet Clean lint free rags Metal Pick Isopropyl alcohol Multipurpose bicycle grease and brush Bench vise DT Swiss Toolkit HWTXXXOONTK24S ad S SPECIAL gt NSG20s T e Short Installation Cylinders e Long Installation e DT Special Grease Ring Nut Installation e Seal Installation e Long Stepped Tool Tool Tool Tool SAFETY INSTRUCTIONS Always wear nitrile gloves when working with bicycle grease ROAM 60 50 RAIL 50 Rear Wheel Service 24 ROAM 60 50 RAIL 50 Rear Hub Bearing Replacement Pull the end caps from the hub by hand A Park Tool AV 4 Axle Vise can be used if it the end caps are difficult to remove NOTICE Removal of 9 10 speed driver body is the same as for XD driver body py Compatible Park Tool AV 4 Pull the driver body and spring from the hub by hand Remove the two star ratchets 2 Use a pick to remove the internal spring from the hub ROAM 60 50 RAIL 50 Rear Hub Bearing Replacement 25 Remove the aluminum spacer from the axle 5 Strike the axle with a soft face mallet to remove the disc brake side bearing from the hub 6 Remove the bearing from the axle and discard Ring Nut Installation Tool 7 To remove the ring nut first install the Ring Nut Installation Tool into a vise ROAM 60 50 RAIL 50 Rear Hub Bearing Replacement 26 Install the drive side of the hub onto the Ring Nut Installation Tool Press down firmly and rota
6. please refer to the SRAM Wheels Spare Parts List in the Service section of www sram com ses Spoke Length 26 Spoke Length 27 5 Spoke Length 29 Final Spoke Tension Front 24 2 Cross 268 mm 280 mm 298 mm NO kgf 10 kgf 1079 N 98 N Wheel on Brake side al 24 2 Cross 268 mm 280 mm 298 mm NO kgf 10 kgf 1079 N 98 N Wheel on Drive side Front 24 2 Cross 270 mm 281 mm 300 mm NO kgf 10 kgf 1079 N 98 N Wheel on Brake side Rear 24 2 Cross 270 mm 281 mm 300 mm NO kgf 10 kgf 1079 N 98 N Wheel on Drive side Toni 24 2 Cross 270 mm 281 mm 300 mm NO kgf 10 kgf 1079 N 98 N Wheel on Brake side Rear 24 2 Cross 270 mm 281 mm 300 mm NO kgf 10 kgf 1079 N 98 N Wheel on Drive side ROAM 60 O in 2 lt O a 4 RAIL 50 Wheel Build amp Sooke Replacement 39 DORAIN www sram com GEN 0000000004463 Rev A 2013 SRAM LLC
7. IA 2014 ROAM 60 50 RAIL 50 service Manual SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein SRAM warrants its products to be free from defects in materials or workmanship for a period of two years after original purchase This warranty only applies to the original owner and is not transferable Claims under this warranty must be made through the retailer where the bicycle or the SRAM component was purchased Original proof of purchase is required all warranties including any implied warranties of reasonable care merchantibility or fitness for a particular purpose are hereb disclaimed LOCAL LAW This warranty statement gives the customer specific legal rights The customer may also have other rights which vary from state to state USA from province to province Canada and from country to country elsewhere in the world To the extent that this warranty statement is inconsistent with the local law this warranty shall be deemed modified to be consistent with such law under such local law certain disclaimers and limitations of this warranty statement may apply to the customer For example some states in the United States of America as well as some governments outside of the United States including provinces in Canada may a Preclude the disclaimers and limitations of this warranty statement from limiting the statutory rights of the consumer e g United Kingdom b Otherwise
8. come off of the axle 6 Lightly grease the bearing bores Install the axle into the hub and bearing ROAM 60 amp RAIL 50 End Cap Replacement 7 Insert one of the FR 440 Front Hub Tools into the hub against the face of the installed bearing FR 440 Front Hub Tool Place the FR 440 Front Hub Tool and wheel onto a bench Install the other bearing onto the axle with the red seal facing away from the hub 10 Insert the Small Stepped Tool into the axle and bearing Install the FR 440 Front Hub Tool other FR 440 Front Hub Tool onto the Small Stepped Tool and against the bearing face Small Stepped Tool 11 Strike the FR 440 Front Hub Tool with a soft face mallet until the bearing is firmly seated into the bearing pocket ROAM 60 amp RAIL 50 End Cap Replacement 8 12 Check the axle for play by pushing and pulling it in the hub If any play is detected repeat steps 8 11 Lightly grease the face of each bearing Thread the new end caps onto the axle Tighten the end caps to 14 15 Nem 133 in lb ROAM 60 amp RAIL 50 End Cap Replacement 9 ROAM 60 amp RAIL 50 Front Hub Bearing Replacement 20 mm or 15 mm thru axle end caps use 2x 22 mm open end wrenches or adjustable wrenches Quick release QR end caps use 2x 5 mm hex wrenches Hold one wrench stationary and turn the other wrench counterclockwise One end cap will unthread from the hub and the other will remain on the axle Quick Release In
9. e Long Installation Tool with a soft face mallet until the rotor seal is seated in the hub shell Long Installation Tool ROAM 60 50 RAIL 50 Rear Hub Bearing Replacement 31 Install the Ring Nut Installation Tool in a vise Install the drive side of the axle into the Ring Nut Installation tool and press down firmly to make sure that the teeth of the tool engage the teeth of the ring nut Ring Nut Installation Tool 27 Pull the axle out of the hub about 2 cm Install a new bearing onto the axle with the red seal facing away from the hub NOTICE You may need to remove the axle from the hub install the bearing onto the axle and then reinstall the axle into the hub and Short Installation Cylinder 28 Install a Short Installation Cylinder onto the axle and bearing Strike the Short Installation Cylinder with a soft face mallet until the bearing is firmly seated into the bearing pocket Short Installation Cylinder 29 Check the axle for play by pushing and pulling it in the hub If any play is detected repeat step 28 ROAM 60 50 amp RAIL 50 Rear Hub Bearing Replacement 32 Apply a light layer of grease to the face of the non drive side bearing Use a rag or paper towel to remove any grease from the end of the axle 3 Apply a very thin layer of DT Special Grease to the teeth of the ring nut DT Special Grease 32 Install the spacer onto the axle as far as possible 33 Install the spring onto the axl
10. e and over the spacer The wide opening of the spring is toward the hub ROAM 60 50 RAIL 50 Rear Hub Bearing Replacement 33 34 Clean both star ratchets and inpect for damage If either star ratchet is damaged the damaged part must be replaced Apply a very thin layer of DT Special Grease to all surfaces of both star ratchets DT Special Grease NOTICE Only use DT Special Grease on the star ratchets Using any other grease or applying too much DT Special Grease can prevent the ratchets from engaging If the ratchets do not engage properly clean them and reapply a thin layer of DT Special Grease DT Special Grease 35 Install the two star ratchets onto the axle Clean the driver body and install the spring into the driver body The wide opening of the spring is against the driver body NOTICE Installation of the 9 10 speed driver body is the same as for XD driver body 37 Install the driver body onto the axle Firmly press the driver body against the hub to make sure the teeth of the driver body are engaged with the teeth of the star ratchets and ring nut ROAM 60 50 RAIL 50 Rear Hub Bearing Replacement 34 Apply a thin layer of grease to the driver body bearing Use a rag or paper towel to remove any grease from the ends of the axle Press the end caps onto the hub by hand NOTICE Only use the end cap labeled XD Compatible when installing an XD driver body ROAM 60 50 RAIL 50 Rear Hub Beari
11. e bearing from the axle and discard 5 Insert one end of the axle through the hub and into the installed bearing Install the Long Stepped Tool into the axle Strike the axle with a soft face mallet to remove the bearing from the hub Remove the bearing from the axle and discard Long Stepped Tool ROAM 50 Front Hub Bearing Replacement 19 EJ Clean the inside of the hub using isopropyl alcohol and a rag El Lightly grease the bearing bores 10 Install a new bearing onto the long end of the axle with the red seal facing away from the axle po Install the axle into the hub through the disc brake side of the hub mat Na V A ROAM 50 Front Hub Bearing Replacement 20 12 Install one of the Large Diameter Hub Tools into the non brake side of the hub This will help maintain the alignment of the axle 13 Place the Large Diameter Hub Tool and wheel onto a bench with the disc brake side facing up 14 Install the other Large Diameter Hub Tool over the axle end and into the hub Strike the tool with a soft face mallet until the bearing is firmly seated into the bearing pocket Large Diameter Hub Tool EE RAM b fi ES a ROAM 50 Front Hub Bearing Replacement 21 15 Turn the wheel over so that the Large Diameter Hub Tool and installed bearing are on the work bench Install a new bearing onto the axle 16 Install the other Large Diameter Hub Tool over the
12. ecceseceeccneccneceneceneecneeeusenaeceeseuesenesenssenesauseenseeaeeneseuasenssenssenesenseonssenseesenasens 24 Parts and TOOIS dl dit E RN 24 ROAM 60 50 amp RAIL 50 Rear Hub Bearing eolica ti ee cn a lent 25 Tubeless RIM Tal 0 CS ntsc air ne dut diese A en ones din nneue A A 36 PRESARIO nr A oe ec canes co sd cos ec eo receto 36 TUDECIESS RI Tape Instalan e e et on dae 36 valve Stem AAS ala Ote a tenets TE e M ee rete 38 Wheel Build amp Spoke Replacement acom nismes ti a eciaci Rain aid tance ss 39 RED Centenars mea A A A Tia i Tc die 39 Table of Contents 3 SAFETY FIRST We care about YOU Please always wear your safety glasses and protective gloves when servicing SRAM products Protect yourself Wear your safety gear ROAM 60 amp RAIL 50 Front Wheel Service We recommend that you have your SRAM wheels serviced by a qualified bicycle mechanic Servicing SRAM products requires knowledge of bicycle components as well as the special parts and tools for service For exploded diagram and part number information please refer to the Spare Parts Catalog available on our web site at www sram com For order information please contact your local SRAM distributor or dealer Information contained in this publication is subject to change at any time without prior notice For the latest technical information please visit our website at sram com Your product s appearance may differ from the pictures diagrams contained in this publicatio
13. ll the other FR 440 Front Hub Tool over the axle and into the hub Strike the tool with a soft face mallet until the bearing is firmly seated into the bearing pocket FR 440 Front Hub Tool ROAM 60 amp RAIL 50 Front Hub Bearing Replacement 13 Remove the upper LFR 440 Front Hub Tool from the axle Install a 15 new bearing onto the axle with the red seal facing away from the hub 16 Insert the Small Stepped Tool into the end of the axle Install the other FR 440 Front Hub Tool on top of the Small Stepped Tool Small Stepped Tool 17 Strike the FR 440 Front Hub Tool with a soft face mallet until the bearing is firmly seated into the bearing pocket 18 Check the axle for play by pushing and pulling it in the hub If any play is detected repeat steps 16 and 17 ROAM 60 amp RAIL 50 Front Hub Bearing Replacement 14 19 Lightly grease the face of each bearing Thread the new end caps onto the axle Tighten the end caps to 15 Nem 133 in lb Y ZA 15 Nem 33 in lb 5 mm hex ROAM 60 amp RAIL 50 Front Hub Bearing Replacement 15 ROAM 50 Front Wheel Service We recommend that you have your SRAM wheels serviced by a qualified bicycle mechanic Servicing SRAM products requires knowledge of bicycle components as well as the special parts and tools used for service For exploded diagram and part number information please refer to the Spare Parts Catalog available on our web site at www sram com For order inf
14. n Parts and Tools e Nitrile gloves e 2 5mm hex wrenches e Apron e 2 22 mm open end wrenches e Clean lint free rags or e Isopropyl alcohol 2 Adjustable wrenches e Multipurpose bicycle grease and brush e Torque wrench e Bench vise e Rubber mallet DT Swiss Toolkit HWTXXXOONTK24S a e FR 440 Front Hub Tools e Fabric Strap tool e Small Stepped Tool SAFETY INSTRUCTIONS Always wear nitrile gloves when working with bicycle grease ROAM 60 RAIL 50 Front Wheel Service 5 ROAM 60 amp RAIL 50 End Cap Replacement 20 mm or 15 mm thru axle end caps use 2x 22 mm open end wrenches or adjustable wrenches Quick release QR end caps use 2x 5 mm hex wrenches Hold one wrench stationary and turn the other wrench counterclockwise One end cap will unthread from the hub and the other will remain on the axle Quick Release Insert the Small Stepped Tool into the open end of the axle Small Stepped Tool Use a soft face mallet to tap out the axle from the hub ROAM 60 amp RAIL 50 End Cap Replacement 6 4 Wrap the Fabric Strap Tool tightly around the axle Pull down firmly on the strap while clamping the strap in the vise NOTICE Only use the Fabric Strap Tool to secure the axle in the vise Do not clamp the axle directly in the vise Fabric Strap Tool 5 Remove the end cap If the axle rotates in the strap tool remove it from the vise and pull the strap tighter Make sure the bearing does not
15. ng Replacement 35 Tubeless Rim Tape We recommend that you have your SRAM wheels serviced by a qualified bicycle mechanic Servicing SRAM products requires knowledge of bicycle components as well as the special parts and tools used for service For exploded diagram and part number information please refer to the Spare Parts Catalog available on our web site at www sram com For order information please contact your local SRAM distributor or dealer Information contained in this publication is subject to change at any time without prior notice For the latest technical information please visit our website at sram com Your product s appearance may differ from the pictures diagrams contained in this publication Parts and Tools e ROAM 50 60 26 mm width rim tape e Wheel truing stand e RAIL 50 28 mm width rim tape e Isopropyl alcohol e Nitrile gloves e Small flashlight e Apron e Small knife e Clean lint free rags e Scissors Tubeless Rim Tape Installation Install the wheel into a truing stand Remove any existing rim strips or rim tape from the rim Remove the valve stem Thoroughly clean the rim with isopropyl alcohol and a clean rag Make sure that the rim is dry and free of alcohol Spinning the wheel rapidly in the truing stand can help remove alcohol from the spoke holes 2 Apply the beginning section of tape between the two spoke holes that are 180 degrees opposite from the valve stem hole Press 4 5 inches 10 13 cm
16. ormation please contact your local SRAM distributor or dealer Information contained in this publication is subject to change at any time without prior notice For the latest technical information please visit our website at sram com Your product s appearance may differ from the pictures diagrams contained in this publication Parts and Tools e Nitrile gloves e Park Tool AV 4 axle vise e Apron e Torque wrench e Clean lint free rags e Rubber mallet e Isopropyl alcohol e Multipurpose bicycle grease and brush e Bench vise DT Swiss Toolkit HWTXXXOONTK24S P ES e Large Diameter Hub Tools Long Stepped Tool SAFETY INSTRUCTIONS Always wear nitrile gloves when working with bicycle grease ROAM 50 Front Wheel Service 16 ROAM 50 End Cap Replacement Pull the end caps from the hub by hand A Park Tool AV 4 Axle Vise can be used if the end caps are difficult to remove Park Tool AV 4 Press the new end caps onto the hub by hand NOTICE The tall end cap is installed on the disc brake side of the hub ROAM 50 End Cap Replacement 17 ROAM 50 Front Hub Bearing Replacement Pull the end caps from the hub by hand A Park Tool AV 4 Axle Vise can be used if the end caps are difficult to remove Park Tool AV 4 Install the Long Stepped Tool into one side of the axle Long Stepped Tool Use a soft face mallet to tap out the axle from the hub ROAM 50 Front Hub Bearing Replacement 18 Remove th
17. orrectly installed and or adjusted according to the respective SRAM user manual The SRAM user manuals can be found online at sram com rockshox com avidbike com truvativ com or zipp com This warranty does not apply to damage to the product caused by a crash impact abuse of the product non compliance with manufacturers specifications of usage or any other circumstances in which the product has been subjected to forces or loads beyond its design This warranty does not apply when the product has been modified including but not limited to any attempt to open or repair any electronic and electronic related components including the motor controller battery packs wiring harnesses switches and chargers This warranty does not apply when the serial number or production code has been deliberately altered defaced or removed This warranty does not apply to normal wear and tear Wear and tear parts are subject to damage as a result of normal use failure to service according to SRAM recommendations and or riding or installation in conditions or applications other than recommended Wear and tear parts are identified as e Dust seals e Stripped threads bolts e Handlebar grips e Spokes e Bushings aluminium titanium e Shifter grips e Free hubs e Air sealing o rings magnesium or steel e Jockey wheels Aero bar pads e Glide rings Brake sleeves e Disc brake rotors e Corrosion Rubber moving parts Brake pads Wheel braking surfaces e Tools
18. restrict the ability of a manufacturer to enforce such disclaimers or limitations For Australian customers This SRAM limited warranty is provided in Australia by SRAM LLC 1333 North Kingsbury 4th floor Chicago Illinois 60642 USA To make a warranty claim please contact the retailer from whom you purchased this SRAM product Alternatively you may make a claim by contacting SRAM Australia 6 Marco Court Rowville 3178 Australia For valid claims SRAM will at its option either repair or replace your SRAM product Any expenses incurred in making the warranty claim are your responsibility The benefits given by this warranty are additional to other rights and remedies that you may have under laws relating to our products Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure LIMITATIONS OF LIABILITY To the extent allowed by local law except for the obligations specifically set forth in this warranty statement in no event shall SRAM or its third party suppliers be liable for direct indirect special incidental or consequential damages LIMITATIONS OF WARRANTY This warranty does not apply to products that have been inc
19. sert the Small Stepped Tool into the open end of the axle Small Stepped Tool Use a soft face mallet to tap the axle from the hub ROAM 60 amp RAIL 50 Front Hub Bearing Replacement 10 4 Wrap the Fabric Strap Tool tightly around the axle Pull down firmly on the strap while clamping the strap in the vise NOTICE Only use the Fabric Strap Tool to secure the axle in the vise Do not clamp the axle directly in the vise Fabric Strap Tool 5 Remove the end cap If the axle rotates in the strap tool remove it from the vise and pull the strap tighter 6 Remove the bearing from the axle Insert one end of the axle into the hub and into the installed bearing Press the axle in as far as possible until it comes out of the bearing ROAM 60 amp RAIL 50 Front Hub Bearing Replacement 11 Insert the Small Stepped Tool into the axle Strike the axle with a soft face mallet to remove the bearing from the hub Remove the bearing from the axle and discard Install a new bearing onto the axle with the red seal facing away from the axle Clean the hub using isopropyl alcohol and a rag ROAM 60 amp RAIL 50 Front Hub Bearing Replacement 12 Lightly grease the bearing bores 12 Insert the axle and bearing into the disc brake side of the hub FR 440 Front Hub Too Install one of the FR 440 Front Hub Tools over the axle end and against the bearing Place the FR 440 Front Hub Tool and wheel onto a bench 14 Insta
20. te the wheel to make sure that the teeth of the tool engage with the ring nut Press down firmly and rotate the wheel counter clockwise to remove the ring nut from the hub The rotor seal will also be removed and may fall over the ring nut tool onto the vise Remove the ring nut from the tool Clean the ring nut and inspect for any damage Replace the ring nut if it is damaged Use a pick to remove the shim ring from the hub ROAM 60 50 RAIL 50 Rear Hub Bearing Replacement 27 11 Insert the short end of the axle through the disc brake side of the hub and into the drive side bearing 12 Strike the axle with a soft face mallet to remove the bearing from the hub Remove the bearing from the axle and discard 14 Clean the inside of the hub using isopropyl alcohol and a rag ROAM 60 50 amp RAIL 50 Rear Hub Bearing Replacement 28 Lightly grease the bearing bores 16 Install one of the Short Installation Cylinders into a vise Install a new bearing onto the long end of the axle with the red seal facing away from the axle Short Installation Cylinder 17 Install the long end of the axle into the Short Installation Cylinder Firmly press down on the axle to seat the bearing onto the axle 18 Install the drive side of the hub onto the axle and bearing ROAM 60 50 amp RAIL 50 Rear Hub Bearing Replacement 29 19 Install the other Short Installation Cylinder over the axle and into the hub Strike the Short
Download Pdf Manuals
Related Search