hot series pressure washer operator`s manual
Contents
1. 10 ALTO Lea el manual de operaci n antes de operar sta m quina Omisi n de leer el instructivo de seguridad y operaci n pueda resultar en lesi n per sonal o dano a la propiedad Conecte la manguera del suministro de agua al conector de entrada y abra la llave de paso Revise los niveles de aceite y combustible Conecte la manguera de alta presi n al niple de descarga deslizando el acople r pido hacia atr s si se va a utilizar algun detergentes instale el inyector apropiado para detergentes como se muestra en la pagina E Inserte el cople rapido al niple de descarga y as gurelo empujando el collar del conector rapido hacia adelante Instale firmemente la boquilla de alta presi n que desee a la varilla de aspersi n como se describe en los pasos 4 y 5 Conecte el cable el ctrico a la fuente de poder apropiado y oprima el bot n de encendido del cable el ctrico GFCI Sujete firmemente la varilla de aspersi n y abra la v lvula de presi n en sentido inverso a las manecillas del reloj Oprima el switch en posici n de la bomba hidr ulica cuando obtenga un flujo cont nuo de agua por la varilla de aspersi n La unidad se encuentra lista para utilizar agua fr a para limpieza al abrir la v lvula de presi n en sentido de las manecillas de reloj para alcanzar la presi n deseada Para utilizar agua caliente oprima el switch en posici n del quemador El quemador se e2. Burner Motor 7 21805U 7 21805U 7 21805U 7 21805U 7 2899U 7 2899U Burner Motor 7 0005 7 0005 7 0005 7 0005 7 0005 7 0005 7 20388 7 20383 Fuel Pump Solenoid Cord 7 21844U 7 21844U 7 21844U 7 21844U 7 21844U 7 21844U Fuel Pump 7 0009 7 0009 7 0009 7 0009 7 0009 7 0009 7 13645 7 13645 LANDA HOT 96 626 REV 2 04 Fuel Solenoid Coil 7 21755U 7 21755U 7 21755 7 21755U 7 217550 7 21755U Fuel Solenoid Coil 7 000961 1 7 000961 1 7 000961 1 000961 1 4 000961 1 000961 1 000961 1 000961 1 Electrode 7 578727 7 578727 7 518727 7 518727 1 9 8727 7 578727 Electrode 7 13286 7 13286 7 13286 7 13286 7 13286 7 13286 7 13286 7 13286 HOT SERIES PRESSURE WASHER operator s MANUAL 5 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION LOW OPERATING Faulty pressure gauge Install new gauge PRESSURE Insufficient water supply Use larger garden hose clean filter washer at water inlet Old worn or incorrect spray nozzle Match nozzle number to machine and or replace with new nozzle Plumbing or hose leak Check plumbing system for leaks Retape leaks with teflon tape Faulty or misadjusted unloader valve Adjust unloader for proper pressure Install Where applicable repair kit when needed Worn packing in pump Install new packing kit Fouled or dirty inlet or discharge valves Clean inlet and dis
3. 96 626 REV 2 04 is HOT SERIES PRESSURE WASHER operator s MANUAL COMBUSTION ASSEMBLY EXPLODED VIEW REV 2 04 96 626 LANDA HOT COMBUSTION ASSEMBLY EXPLODED VIEW PARTS LIST ITEM PART NO 2 00101 2 95 07121113 3 7 0144 4 4 02047725 4 02047722 9 2 00602 6 2 00120 7 2 00241 8 2 2007 2 0079 9 7 0140 10 4 0509 4 0510 11 2 0039 12 95 07121012 13 95 07121212 14 7 01430 15 7 01484 16 7 0141 17 7 12484 31332 18 95 07121011S 19 90 19995 20 7 01470 21 95 07101257 22 90 2018 23 2 01104 24 2 00091 eo 2 1085 DESCRIPTION QTY Nipple 1 2 x 4 Galv Sch 80 1 PHW Insulation Retainer 2 Gasket Burner Plate Hose 25 x 3 8 Pressure Loop 100R2 Except 2 1100 2 1500 3 300 1 Hose 22 x 3 8 Pressure Loop 100R2 2 1100 2 1500 3 300 1 Elbow 1 2 JIC x 1 2 Fem 1 Nipple 1 2 x 5 Galv Sch 80 1 Coupling 1 2 x 3 8 Pipe 1 Nipple 3 8 x 3 8 NPT ST Male1 A Swivel 1 2 JIC Fem 3 8 Male 3 300 1 Insulation Front Head No Hole 1 Switch Snap 225 Hi Limit 1 Switch Snap 340 3 300 1 Cross Female 1 2 Pipe Steel 1 Bottom Wrap Yellow 1 Coil Replacement Schedule 80 W Steel Wrap 1 Insulation Blanket W No Foil 24 x 57 1 Insulation Blanket Die Cut 1 Insulation Burner Head W Hole 1 Gasket Standard Large 4 3000 Burner Gasket Top Wrap All Yellow Screw Cap 10 32 x 3 4 BM NF SS SOC 4 Insulation Gaske
4. 96 626 REV 2 04 PUMP ASSEMBLY HOT2 1100 HOT2 1500 HOT3 1100 HOT4 2000 HOT4 3000 PARTS LIST ITEM 1 O01 amp PO 4 10 11 12 13 14 15 16 17 PART NO 2 0051 2 00512 2 0079 2 0053 2 00270 2 106301 2 1060 4 02047725 4 02047722 5 23011 5 23123 5 2307 5 1046 5 1047 5 1053 5 1063 5 10531 5 1059 6 051532 6 051595 2 300816 2 1105 4 02110000 2 1034 2 10942 2 1902 2 30062 5 3208 DESCRIPTION QTY Nipple 1 2 JIC x 3 8 Pipe 4 2 4 3 1 Nipple 1 2 JIC x 1 4 Pipe 2 1100 2 1500 3 1100 1 Swivel 1 2 JIC Fem 3 8 Male 1 Elbow 1 2 JIC x 3 8 Steel 1 Elbow 3 8 Male 1 Nipple 1 2 JIC x 3 8 45 1 Elbow 1 2 JIC x 3 8 1 Hose 25 x 3 8 100 R2 Pressure Loop Except 2 1100 2 1500 1 Hose 22 x 3 8 100 R2 Pressure Loop 2 1100 2 1500 1 Pump Gen TT9111 2 1100 2 1500 3 1100 1 Pump Gen TX 1812S17 4 20021A G K 1 Pump General TS 2021 4 3000 1 Motor 1 5 HP 1 PH Baldor 2 1100 1 Motor 2 HP 1 PH Baldor 2 1500 3 1100 1 Motor 5 HP 1 PH Baldor 4 2000 1 Motor 7 5 380V 3HP 1425 RPM 4 3000N 1 Motor 5 HP 1Ph 3450 RPM 200V 4 2000G 1 Motor 5HP 1PH 220V 2850RPM 50 Hz 4 2000K 1 A Strain Relief 1 2 LQ Tite 2 1100 2 1500 3 1100 3 300 1 A Strain Relief 3 4 LQ Tite 4 2A G K 4 3N 1 Pump Protector 3 8 1 Swivel 1 2 JIC Female Push On 2 Hose 1 2 Push On 1 ft Cross 3 8 Female 1
5. 90 2018 90 1999 5 40108401 5 40102258 5 602034 5 512024 95 07121112 95 07141110 90 2007 90 10220 90 4002 90 1016 90 2002 90 1007 90 4001 90 2001 2 01164 95 07162007 2 10942 DESCRIPTION QTY Pump AR XMA35G25N 1 Motor 1 5 HP 1 PH 3450 RPM Baldor Elbow 1 2 JIC x 1 2 90 Tee 1 2 Street Nut Cage 1 4 x 12 Gauge Bushing 1 2 x 1 4 Switch Flow MV 60 Switch Reed Replacement NO MV 60 1 Hose 1 4 1 2 Braided Vinyl 3 ft Clamp Hose UNI 46 54 1 Hose Barb 1 4 Barb x 1 4 Pipe 90 Nut Cage 10 32 x 16 Gauge Screw 10 22 x 3 4 BH SOC CS Pulley AK 84 H Pulley Bore AK 22 x 5 8 Belt AX 34 Bushing H x 24 mm O Rail Pump Combo Retainer Pump Take Up Nut 3 8 Hex NC Bolt 3 8 x 3 1 2 Tap Washer 3 8 Flat Bolt 3 8 x 1 NC HH Nut 3 8 ESNA Bolt 5 16 x 1 NC HH Washer 5 16 Flat Nut 5 16 ESNA Tank Plastic Universal Float sch mas OO O oc Hose Connection Bracket PHW PHWS OHW 1 Swivel 1 2 MP x 3 4 GHF W Strainer 1 ITEM 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 o1 52 53 54 PART NO 2 0079 2 3014 95 07121207 1 2 5 2 1906 90 4017 2 11041 2 0151 90 4030 90 4031 90 4032 4 02140000 2 3015 4 02080000 2 1085 90 4005 90 40073 2 9040 2 01411 2 1
6. Series Il Plate Cover 1 4 3N 2 22 See Page 22 For Nozzles 6 051532 Strain Relief LQ Tite 2 1 100 23 6 051818 Locknut 314 8465 2 2 1500 3 1100 3 300 2 24 2 4081 Gasket Electrical Box Short 2 5 95 07121118 Cover Dual Valve Series 1 l l 25 2 40811 Gasket Electrical Box Long 2 6 6 05153 Strain Relief STRT LQ Tite 1 26 2 01411 Snap Bushing 3 4 1 7 6 05181A Locknut 1 2 8463 2 eee l 27 95 071211172 Cover 3 Position Switch Series 8 6 020201 Switch Rotary 3 Position 1 Control Box LOT 1 9 90 40073 A Washer 5 8 Star Internal 1 2g 6 01060 Cord W GFCI Plug 120V 20 Amp 10 6 05152 Strain Relief STRT LQ Tite 1 2 1100 2 1500 3 1100 11 6 0128 Conduit Watertight po 8300 Il Black 0 9 GFCI 240 30 Amp W Cord 13 10 08021 Label Disconnect Pwr Supply 1 lt 14 2 Label Ground 6 0105 Service Gord 12 4 4 3000N 36 ft 15 95 07121029 Lid Elect Box PHWS HOT OHW 4 6 0108 Cord Service 10 3 4 2000K 36 ft 16 95 07104154 Plate Stand Off E Bar PHWS 1 EE 29 90 180101 Screw 8 32 1 2 16 17 95 07101242 Assy Elect Box PHWS HOT OHW y 30 6 7103002 Wire Assy 10 Gauge 8 Wire 20 1 A Not Shown LANDA HOT 96 626 REV 2 04 1 HOT SERIES PRESSURE WASHER operator s MANUAL CHASSIS ASSEMBLY EXPLODED VIEW LANDA HOT 96 626 REV 2 04 HOT SERIES PRESSURE WASHER operator s MANUAL 15 CHASSIS ASSEMBLY EXPLODED VIEW PA
7. Swivel 1 2 MP x 3 4 GHF W Strainer Strainer Inlet Garden Hose Valve Anti Siphon Watts 8B Unloader AL607 h sch ITEM 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 PART NO 5 512024 5 40106401 5 40208401 5 40407501 5 40506701 5 40102158 5 40204401 5 40403601 9 40102758 5 511075 5 511138 5 40504501 5 602033 0 604034 5 602031 5 602037 90 2001 2 1005 2 1058 90 4001 6 021740 90 1007 90 2002 2 1099 2 100510 95 07121112 95 07121111 95 07141110 90 2007 90 10220 90 4002 90 1016 6 021730 95 07121013 LANDA HOT 96 626 REV 2 04 HOT SERIES PRESSURE WASHER oreraror S MANUAL 21 DESCRIPTION QTY Bushing H x 24 mm 1 Pulley AK64H 2 11021 2 15021 3 11021 Pulley 2AK84H 4 20021K Pulley BK75H 4 20021A G Pulley 2BK67H 4 30021N Pulley Bore AK 21 x 5 8 2 1100 2 1500 1 Pulley 28644 4 20021K 1 Pulley BK36H 4 2000A G 1 Pulley Bore AK 27 x 5 8 3 11021 1 A Bushing H x 3 4 4 2000A G K 1 A Bushing H x 1 3 8 4 3000 1 Pulley 2BK45H 4 30021N 1 Belt AX 33 3 11021D 1 Belt BX 34 4 20021A G 4 30021N 1 Belt AX 31 2 11021 1 Belt AX37 4 2000K 1 Nut 5 16 ESNA 4 Nipple 3 8 Hex 2 1100 2 1500 3 1100 1 Nipple 1 2 Pipe x 3 8 Pipe 4 20021A G K 4 30021N 1 Washer 5 16 Flat 8 Replacement Reed MV 60 1 Bolt 5 16 x 1 NC HH 4 Nut 3 8 ESNA 6 Coupling 1 2 x 3
8. detergentes con el uso del juego de inyectores detergentes Landa 1 Tire el collar de enganche r pido del inyector hacia atr s y aseg relo en la boquilla de descarga La flecha del cuerpo de la v lvula del inyector debe apuntar en la direcci n del flujo 2 Conecte la manguera de descarga a presi n a la boquilla de inyector asegurando el conector r pido Boquilla de Cobre para Detergente gt Boquilla de Varilla Hy Presion Q Mango de Control C AN JA 0 6 WY a SN dy I CT p m A m7 Qo UH 000000 Presion 0 Wy NNN 20009 0022 AAL TT up 72 NNN NAY NA he 1 Arranque la m quina como se indica en las instrucciones de operaci n Coloque el tubo de la toma de detergent en el recipiente de la soluci n de detergente Abra el gatillo de la pistola La proporci n de soluci n de detergent es aproximadamente de 15 a 1 Cuando termine de lavar enjuague simplemente soltando el gatillo de la pistola removiendo la boquilla para detergente y reemplazando la boquilla de presi n hacia atr s en el conector r pido NOTA El inyector detergente no puede actuar como sif n con la boquilla de alta presi n en el extremo final de la varilla Para la limpieza coloque el tubo para tomar los detergentes en el recipiente con agua transparente y siga los pasos 5 y 6 para prevenir que dep sitos detergentes danen el inyector Conector Conector R pido R pido I
9. no se adhieran a las especificaciones contenidas en el Manual del operador 3 Da o a causa de heladas deterioro debido a productos qu micos acumulaci n de escamas oxidaci n corrosi n o expansi n t rmica Da o a los componentes debido a fluctuaciones en el suministro el ctrico o al abastecimiento de agua Servicio de mantenimiento normal incluso los ajustes limpieza del sistema de combustible y de obstrucciones Transporte al centro de servicios cargos por mano de obra en planta o da o ocurrido durante el flete El trabajo de mano de obra se excluye especialmente para todas las m quinas que se utilizan como equipos de alquiler QU DEBE HACER PARA OBTENER EL SERVICIO DE LA GARANT A A pesar de no ser necesario para el servicio de garant a le solicitamos que registre su unidad para el lavado a presi n Para ello llene la tarjeta de registro y env ela a vuelta de correo Para obtener el servicio de LANDA de la garant a debe hacer llegar el producto a un Distribuidor de LANDA autorizado con flete prepago acompanado del comprobante de la compra dentro del per odo prescrito por la garant a En caso de que el producto est instalado de forma permanente deber notificar el defecto a su Distribuidor Autorizado de LANDA EI distribuidor Autorizado de LANDA presentar un reclamo a Landa la cual deber verificar el defecto En la mayor a de los casos deber enviar la parte a LANDA con flete prepago junto con el recla
10. sult in a serious explosion NEVER use crankcase or waste oil in your burner Fuel unit malfunction could re sult from contamination Electrode Setting Wayne See illustration below 3 8 Y A Top View Side View Periodically check wiring connections lf it is necessary to adjust electrodes use diagram Electrode Setting Beckett See illustration below Electrode gt 5 32 Gap N Nozzle 116 gt Top View Side View LANDA HOT 96 626 A Electrodes ETT 1 2 2 7 8 V 3 16 EE Adapte Ignition Circuit Periodically inspect wires spring contact and electrodes for condition security and proper spacing Transformer test CAUTION 10 000 VOLTS use defect free insu lated screwdriver and keep fingers off blade Lay blade across one contact OK if arc will span 1 2 between end of blade and other contact see illustration below Transformer Check Mags LCG Burner Nozzle Keep the tip free of surface deposits by wiping it with a clean solvent saturated cloth being careful not to plug or enlarge the nozzle For maximum efficiency replace the nozzle each season Fuel Control System These machines utilize a fuel solenoid valve located on the fuel pump to
11. MANUAL HOW TO USE THE DETERGENT INJECTOR WARNING Some detergents may be harmful if inhaled or ingested causing severe nausea fainting or poisoning The harmful ele ments can cause property dam age or severe injury This machine can siphon and mix detergents with the use of Landa s detergent injector kit 4 WARNING SOME DETERGENTS MAY BE HARMFUL IF INHALED OR INGESTED Downstream Injector 1 Pull injector quick coupler collar back and secure on discharge nipple Injector valve body arrow should point in direction of flow 2 Connect high pressure hose to injector nipple se curing quick coupler 3 Start machine as outlined in Operating Instructions 4 Place detergent pick up tube into container of deter gent solution High Limit Brass Soap Thermostat Nozzle Variable Pressure p Wand VP Q High Pressure Nozzle Quick Coupler Variable Pressure Control Handle LANDA HOT 96 626 0 d m 0 Wy NM 5 Turn pressure control handle counterclockwise on the variable pressure wand This lowers the pressure by directing the water flow through the soap nozzle and allows the detergent injector to siphon soap 6 Open trigger on spray gun Water detergent ratio is approximately 15 to 1 7 When you finish washing rinse by simply turning the variable pressure wand control handle clockwise to increase pressure NOTE The detergent injector will not siphon with the high press
12. certain responsibilities for the correct care of the equipment Attention to regular preventative mainte nance procedures will assist in preserving the performance of your equipment Contact your Landa Inc dealer for maintenance Regular preventative maintenance will add many hours to the life of your pressure washer Perform maintenance more often under severe conditions MAINTENANCE SCHEDULE Replace Fuel Lines Annually Inspect Daily inspect the oil level Pump Oil Change After first 50 hours then every 500 hours or annually Clean Burner Filter Monthly More often if fuel quality is poor Remove Burner Soot Annually Burner Adjustment Cleaning Annually Replace High Pressure Nozzle Clean Water Screen Filter OIL CHANGE RECORD DATE OIL CHANGED NO OF OPERATING HOURS MONTH DAY YEAR SINCE LAST OIL CHANGE LANDA HOT 96 626 REV 2 04 HOT SERIES PRESSURE WASHER operator s MANUAL 9 LANDA LANDA LIMITED NEW PRODUCT WARRANTY PRESSURE WASHERS WHAT THIS WARRANTY COVERS All LANDA pressure washers are warranted by LANDA ING to the original purchaser to be free from defects in materials and workmanship under normal use for the periods specified below This Limited Warranty is subject to the exclusions shown below is calculated from the date of the original purchase and applies to the original components only Any parts replaced under this warranty will assume the remainder of the part s warranty period FIVE YEAR PARTS AND
13. the machine 20 Do not operate this product when fatigued or under the influence of alcohol or drugs Keep operating area clear of all persons 21 Landa will not be liable for any changes made to our standard machines or any components not pur chased from Landa 22 Do not overreach or stand on unstable support Keep good footing and balance at all times 23 Follow the maintenance instructions specified in the manual 24 When making repairs disconnect from electrical source 25 Turn burner off and pull trigger on spray gun Cool water to 100 F before turning machine off 26 Before disconnecting high pressure hose from hot water outlet turn off burner and allow water to cool to 100 F Then turn off pump motor and water sup ply and open spray gun to relieve back pressure in hose This will prevent coil damage from thermal expansion INSTALLATION Place machine in a convenient location providing ample support drainage and room for maintenance These machines are designed for indoor use They must be stored indoors when not in use Location The location should protect the machine from damaging environmental conditions such as wind rain and freez ing temperatures The machine should be run on a level surface where it is not readily influenced by outside sources such as strong winds freezing temperatures rain etc The machine should be located to allow accessibility for refilling of fuel adjustments an
14. 45 L ow 1 4 Pipe 45 Steel 3 300 1 A Not Shown 12 2 0069 Adapter 1 4 x 3 8 Steel 3 300 1 LANDA HOT 96 626 REV 2 04 HOT SERIES PRESSURE WASHER oreraror Ss MANUAL 3 DOWNSTREAM INJECTOR ASSEMBLY 4 011183 2 1100 2 1500 4 011184 3 1100 4 2000 4 3000 ITEM PART NO 1 3 1202 3 12021 2 2 9040 3 4 02080000 4 2 1904 DESCRIPTION QTY Injector Detergent Non Adjust 070 2 1100 2 1500 1 Injector Detergent 083 3 1100 4 2000 4 3000 1 Clamp Hose UNI 46 54 2 Tube 1 4 x 1 2 Clear Vinyl 6ft Strainer 1 4 Hose Barb 1 LANDA HOT 96 626 REV 2 04 24 HOT SERIES PRESSURE WASHER operator s MANUAL BECKETT BURNER SPECIFICATIONS Model No HOT2 11021D HOT2 15021D HOT3 11021D HOT3 30035D HOT4 20021A HOT4 20021G Burner Assy No 7 00012 7 00012 7 00013 7 00013 7 00010 7 00010 Fuel Nozzle 7 01244 7 01244 7 01245 7 0102 7 0101 7 0101 Transformer 7 23581 7 23581 23581 23581 7 21176U 7 21176U WAYNE BURNER SPECIFICATIONS Model No HOT2 11021D HOT2 15021D HOT3 11021D HOT3 30035D HOT4 20021A HOT4 20021G HOT4 20021K HOT4 30021N Burner Assy No 7 00035 7 00035 700034 00034 7 00033 7 00033 7 00040 7 00042 Fuel Nozzle 7 0121 7 0121 7 0123 7 0126 7 0124 7 0124 7 0124 7 0124 Transformer 20358 20358 20358 20358 7 21153 7 21153 20394 7 20393
15. 8 Reducing 1 Nipple 3 8 x 4 Brass 1 Rail Pump Combo 4 2A G K 1 Rail Pump W TT Pumps 2 1100 2 1500 3 1100 1 Retainer Pump Take Up 1 Nut 3 8 Hex NC 2 Bolt 3 8 x 3 1 2 Tap 2 Washer 3 8 Flat 6 Bolt 3 8 x 1 NC HH 6 1 1 Switch Flow MV 0 Platform Power A Not Shown 22 HOT SERIES PRESSURE WASHER operator s MANUAL HOSE SPRAY GUN amp WAND ASSEMBLY ALL MODELS NCE RE 7 TOM NN I Ze WK NU mH qas ASOT 72 NNN BC 2 Sr PP ITEM PARTNO DESCRIPTION QTY ITEM PART NO DESCRIPTION QTY 1 2 2002 Coupler 3 8 Female 1 13 4 02228850 Hose 50 x 1 2 2 0121 A Quick Coupler O Ring Large 1 Steam Only 3 300 1 4 020334500 Hose 50 x 3 8 100R1 1 Ak nen dins NM 4 01212 Spray Gun Shut Off Series 2000 y 15 2 9019 Hose Barb 3 8 NPT Steam Hose 3 300 2 4 40111351A Wand VP AL 344L 2 MC 83 SSVPKIT Repair Kit AR SS Seat 1 lt a lt gt 4 01111 Steam Wand Complete W Nozzle 5 22001 Coupler 1 4 Male 1 includes Items 7 12 3 300 1 2 0119 A Quick Coupler O Ring Small 1 17 4 12804015 Nozzle SAQCMEG 1504 6 4 06540 Brass Soap Nozzle 1 Yellow 2 1100 4 3000 1 7 4 2000 Nozzle Steam 1 16 Thread End1 4 12803015 Nozzle SAQCMEG 1503 8 2 1097 Coupling 3 8 x 1 4 Reducing 1 Yellow 2 1500 1 4 12805015 Nozzle SAQCMEG 1505 4 0111424 L 47 3 1 T 2 T ie em E EE 2 t 3 UE 9 300 4 12805515 Nozzle SAQCMEG 1505 5 11 2 0058 Elbow 1 4 Pipe
16. 905 2 1105 4 02110000 4 02100009 2 1902 90 1995 90 40002 4 02047722 2 1053 2 0031 2 0051 95 07121013 LANDA HOT 96 626 REV 2 04 HOT SERIES PRESSURE WASHER oreraror s MANUAL 9 DESCRIPTION QTY Swivel 1 2 JIC Fem 3 8 Male 1 Valve Fluidmaster 400A Float 1 Lid amp Hinges Plastic Float Tank 1 Label Landa Stripe 1 Modified Close Nipple 1 2 NPT 1 4 1 Strainer 1 2 Basket 1 Washer 1 3 16 x 2 1 4 STL RBR 1 Connector 1 2 Anchor 1 Plug Float Tank Assembly 1 Screw 5 16 18 x 1 1 2 SS Button Socket 1 Nut 5 16 18 Wing SS 1 Washer 5 16 SS 1 Tubing 5 16 x 9 16 Rubber 1251 A Valve Float Control Metering 1 A Tube 1 4 x 1 2 Clear Vinyl 8 ft 4 Hose Barb 1 4 Barb x 1 4 ML Pipe 2 A Washer 5 8 Flat 1 A Washer 5 8 Star 1 A Clamp Hose UNI 46 54 3 A Bushing 1 Snap 1 A Strainer 1 4 W Check Valve 1 Swivel 1 2 JIC Fem Push on 2 Hose 1 2 Push on 1 ft Inlet Hose 11 Supply Water 1 Strainer Inlet GH 1 Screw 1 4 x 1 2 BH SOC CS 2 Washer 1 4 Black Zinc 4 Hose 3 8 x 22 2 Wire Pressure Loop Nipple 1 2 JIC x 3 8 Pipe Elbow 3 8 Street Nipple 1 2 JIC 3 8 Pipe Platform Power A Not Shown lt sch gt 20 HOT SERIES PRESSURE WASHER operator s MANUAL PUMP ASSEMBLY HOT2 1100 HOT2 1500 HOT3 1100 HOT4 2000 HOT4 3000 16 15 14 o 28 2 1100 2 1500 Models Only LANDA HOT
17. LANDA PRESSURE WASHERS HO OPERATOR S MANUAL HOT2 1100 HOT3 300 HOT4 2000 ll HOT2 1500 HOT3 1100 HOT4 3000 pr 9 For technical assistance or the Landa Dealer nearest you consult our web page at www landa com or call 800 LANDA 4 U 800 526 3248 or 360 833 9100 CONTENTS HODU CUON 4 important ig o FI AUO EEE 4 6 GOMpPOnc a dencia 5 HAMN EL EA AEE E EEE E E 6 7 g NEE 6 7 BS T A 7 Be un LE E 7 Wr E 7 44 A T Tm 7 o 7 Starting and Operating tee el 7 How To Use the Detergent Injector 8 Preventative Maintenance 9 Mamienance and e 9 11 Unloader E 9 oa 9 FOU Limit Hot Water ET 9 PN M 9 EE ol 9 lt 4 4 9 Rupture RI 10 See se 10 a EE 10 PPP nee cee pees eee eee 10 lee dag O EOR e E OA 10 e E 10 FAN NN 10 Fuel Pe 0 osa RUE 10 Air Adjustment et 11 Herovalort 00 ah On COM E 11 Gol E E EE 11 PENNE 12 00 Control Panel Parts Saad 13 Chassis Assembly Ex
18. ONE YEAR LABOR WARRANTY Components manufactured by LANDA such as frames handles top and bottom wraps float tanks fuel tanks belt guards and heating coils Internal components on the oil end of all branded pumps have a five year warranty ONE YEAR MINIMUM ON PARTS AND ONE YEAR LABOR WARRANTY All other components excluding normal wear items as described below will be warranted for one year on parts and labor Parts and labor warranty on these parts will be for one year regardless of the duration of the original component manufacturer s part warranty WARRANTY PROVIDED BY OTHER MANUFACTURERS Motors generators and engines which are warranted by their respective manufacturers are serviced through these manufac turers local authorized service centers LANDA cannot provide warranty on these items WHAT THIS WARRANTY DOES NOT COVER This warranty does not cover the following items 1 Normal wear items such as nozzles guns discharge hoses wands quick couplers seals filters gaskets O rings packings pistons pump valve assemblies strainers belts brushes rupture disks fuses pump protectors 2 Damage or malfunctions resulting from accidents abuse modifications alterations incorrect installation improper servicing failure to follow manufacturer s maintenance instructions or use of the equipment beyond its stated usage specifications as contained in the operator s manual Damage due to freezing chemical deterioration
19. RTS LIST ITEM PART NO DESCRIPTION QTY ITEM PART NO DESCRIPTION QTY 1 95 07121017 Panel Rear Access 1 19 2 1085 Hose Barb 1 4 Barb x 10 02028 A Label Warning 1 4 ML Pipe 1 Exposed Pulleys 1 20 90 1992 Bolt 3 8 x 3 8 Sckt Shdr 1 2 90 50031 Knob Black 3 Pt 5 16 18 x 1 2 21 2 99031 Filter Diesel Fuel Disposable 1 3 90 2023 Nut Cage 5 16 18 Black 2 22 2 9040 Clamp Hose UNI 46 54 6 4 90 4001 Washer 5 16 Flat SAE 2 23 2 010061 Bushing Rubber 2 5 90 1995 Screw 1 4 x 1 2 BH SOC CS2 24 90 2002 Nut 3 8 ESNA NC 4 6 90 2000 Nut 1 4 ESNA NC 2 25 90 2019 Nut Cage 3 8 x 12 Gauge 2 7 95 071210105 Chassis All 1 26 90 1020 Bolt 3 8 x 2 NC HH 6 8 2 01101 Grip Handle Waffle 1 2 27 90 4002 Washer 3 8 Flat 8 9 95 07121110 Handle J PHW 2 28 90 5016 Nut 3 8 16 NC Kimdorf 10 77 Cap PHW W Fuel Gauge 14 1 Wapimg 2 12 10 99051 Label Landa Stripe 1 30 2 1089 Hose Barb 1 4 Barb x 1 4 Pipe 90 1 13 95 07101012 Axle 27 All 2 31 2 01212 Cap Vinyl Flat Yellow 1 14 4 0303 Wheel amp Tire Assembly 4 4 32 95 07290086 Assy Lever Brake 1 15 90 20041 Collar 5 8 Bore Shaft 3010 4 33 90 2001 Nut 5 16 ESNA 1 16 95 07121115 Holder Wand HOT 2 34 90 4002 Washer 3 8 Flat 4 17 10 020110 Label Use Only Kerosene 1 39 4 02100000 Hose 1 4 x 6 Fuel Line 2 18 2 010066 Elbow Fuel Tank 1 36 4 02100000 Hose 1 2 Fuel Line 1 ft 37 2 01157 Cap PHWS w Fuel Gauge 1 A Not Shown LANDA HOT
20. Switches Power Fuel Tank Supply Detergent Pick up l an 2 Tube 2 p Cap En lt Q P es MN 7 d LA EUR d E Detergent Brass Soap inclus Nozzle enm TER MAS ut QUE UU N lt SE N 40 bw SS 0 lt a p Trigger Variable Pressure ppc een Handle High Pressure Nozzle Quick Coupler Pressure Hose Steam Nozzle NOTE On some models the GFCI Reset Button must be pushed in each time the plug is disconnected from the power supply LANDA HOT 96 626 REV 2 04 e HOT SERIES PRESSURE WASHER operator s MANUAL 8 Grip cleaning wand securely with both hands before starting the cleaner Failure to do this could result in injury from a whipping wand WARNING Risk of injection or se vere injury to persons Keep clear of nozzle Do not touch or direct discharge stream at per sons This machine is to be used only by trained operators CAUTION Hot discharge fluid Do not touch or direct discharge stream at persons 9 High pressure developed by these machines can cause bodily injury or damage Use caution when operating Do not point the spray gun at anyone or at any part of the body This machine is to be used only by qualified operators 10 Never make adjustments on machine while it is in operation 4 WARNING HIGH PRESSURE STREAM CAN PIERCE SKIN ANDTISSUES WARNING High pressure spray can cause paint chip
21. ain distances from floor and walls Two feet away should be adequate Water Source Water source for machine should be supplied by a 5 8 D garden hose with a city water pressure of not less than 30 psi If the water supply is inadequate or if the garden hose is kinked the machine will run very rough and the burner will not fire Connection Connect the wand nozzle hose and spray gun where applicable see Component Identification On pipe thread connections use teflon tape to avoid water leaks Venting Adding exhaust vent pipe to your oil fired burner is not recommended The pipe restricts air flow which causes carbon buildup which affects the operation and in creases maintenance on the coil If a stack must be used refrain from using 90 bends If the pipe cannot go straight up then use only 45 bends and go to the next larger size pipe The overall pipe length must not exceed 6 feet LANDA HOT 96 626 STARTING AND OPERATING INSTRUCTIONS To Start 1 STOP Read operator s manual before operating this machine Failure to read operation and warning in structions may result in personal injury or property damage 2 Connect water supply hose to inlet connector and turn water on 3 Check fuel tank and pump oil levels 4 Connect high pressure hose to discharge nipple by sliding quick coupler collar back If detergent is to be applied insert a detergent injector 5 Insert quick coupler onto dischar
22. anual shorting of electrodes Check fuel pump for proper flow Check Improper electrode setting solenoid flow switch on machines with spray Fuel not reaching combustion chamber gun control for proper on off fuel flow control Clogged burner nozzle Water not turned on Turn on water to activate burner flow switch Reed switch malfunction Remove test for continuity and replace as needed Fuel solenoid malfunction Replace if needed Pressure switch malfunction Test for proper operation Replace if needed PUMP MOTOR STOPS Insufficient voltage Use heavier drop cord and check voltage at AFTER A FEW MINUTES receptacle Check name plate for amperage OF OPERATION OR draw STARTS SLOW Plugged nozzle Remove and clean nozzle Turn on water pump flush lines and replace nozzle Wrong spray nozzle See serial plate for minimum nozzle size Automatic overload switch tripped Allow motor to cool then push Red reset button Allow to dry Short in electrical wiring Wire contacts should be clean and tight No breaks in wires Coil liming up causing excessive 566 section on Preventative Maintenance pressure Water pump low or out of oil causing Fill to correct level the pump to bind up LANDA HOT 96 626 REV 2 04 2 HOT SERIES PRESSURE WASHER operator s MANUAL PREVENTATIVE MAINTENANCE This pressure washer was produced with the best available materials and quality craftsmanship However you as the owner have
23. ben abajo estar cubierto por el per odo que especifique su fabricante original con un a o como m nimo La garant a para la mano de obra que se aplica a estas partes ser de un afio sin perjuicio de la duraci n de la garant a del fabricante del componente original GARANT A SUMINISTRADA POR OTROS FABRICANTES Los motores generadores y m quinas est n cubiertos por la garant a de sus fabricantes Los centros de servicios locales autorizados por sus fabricantes prestan el servicio de mantenimiento y reparaci n de dichas unidades LANDA no puede proporcionar garant a alguna para estos art culos REPUESTOS NO CUBIERTOS POR LA GARANT A Estas partes sin incluir el desgaste normal de los art culos que se describen abajo estar n cubiertas por el per odo que especifique su fabricante original Estas partes no est n cubiertas por la garant a de mano de obra ESTA GARANT A NO CUBRE Esta garant a no cubre los siguientes art culos 1 Art culos que tienen un desgaste normal como ser boquillas pistolas mangueras de descarga extensi nes acopladores de conexi n r pida sellos filtros juntas anillos en O empaquetados pistones montaje de v lvulas filtros de malla correas cepillos etc 2 Da o 0 malfuncionamiento debido a accidentes abuso modificaciones alteraciones instalaci n inapropiada servicio inapropiado incumplimiento de las instrucciones de mantenimiento del fabricante o uso del equipo con otros fines que
24. charge valves in pump Worn inlet or discharge valves Replace with valve kit TEMPERATURE transfer WATER we DRAWING holes blocked dirty or damaged plugged valve High viscosity of detergent Dilute detergent to specifications Hole in detergent line s Repair hole Low detergent level Add detergent if needed Variable pressure control handle set Turn variable pressure control handle to allow for high pressure water to flow out of brass soap nozzle PUMP RUNNING Pump sucking air Check water supply and possibility of air NORMALLY BUT seepage PRESSURE LOW ON Valves sticking Check and clean or replace if necessary INSTALLATION Unloader valve 5681 faulty Check and replace if necessary Nozzle incorrectly sized Check and replace if necessary See serial plate for proper size Worn piston packing Check and replace if necessary LANDA HOT 96 626 REV 2 04 2 HOT SERIES PRESSURE WASHER operator s MANUAL TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION FLUCTUATING Check and replace if necessary PRESSURE Blockage in valve Check and replace if necessary Pump sucking air Check water supply and air seepage at joints In suction line Worn piston packing Check and replace if necessary PUMP NOISY Air in suction line Check water supply and connections on suction line Broken or weak inlet or disharge valve Check and replace if necessary springs PRESENCE OF WATER IN OL WATER DRIPPING FROM UNDER PUMP Pump
25. control the flow of fuel to the combus tion chamber This solenoid which is normally closed is activated by the unloader s pressure switch When an operator releases the trigger on the spray gun the un loader goes into a by pass mode thus stopping electri cal current to the fuel solenoid coil With the solenoid closed the fuel supply to the combustion chamber ceases Periodic inspection to insure that the fuel sole noid valve functions properly is recommended This can be done by operating the machine and checking to see that when the spray gun is in the OFF position the burner is not firing Fuel Pressure Adjustment To adjust fuel pressure turn the adjusting screw located at the regulator port clockwise to increase counterclock wise to decrease Do not exceed 200 psi NOTE When changing fuel pump a by pass plug must be installed in return line port or fuel pump will not prime REV 2 04 HOT SERIES PRESSURE WASHER operator s MANUAL 1 1 Air Adjustment Machines are preset and performance tested at the fac tory elevation 100 above sea level A one time initial correction for your location will pay off in economy per formance and extended service life If a smoky or eye burning exhaust is being emitted from the stack two things should be checked First check the fuel to be cer tain that kerosene or No 1 home heating fuel is being used Next check the air adjustment on the burner An oily black smoky fire in
26. d maintenance Normal precautions should be taken by the operator of the machine to pre vent excess moisture from reaching the power unit or electrical controls REV 2 04 HOT SERIES PRESSURE WASHER orERATOR S MANUAL 7 It is recommended that a partition be made between the wash area and the machine to prevent direct water spray from coming in contact with the machine Excess moisture reaching any electrical components or controls will reduce machine life and may cause electrical shorts During installation of the machine beware of poorly ven tilated locations or areas where exhaust fans may cause an insufficient supply of oxygen Sufficient combustion can only be obtained when there is a sufficient supply of oxygen available for the amount of fuel being burned If it is necessary to install a machine in a poorly ventilated area outside fresh air may have to be piped to the burner and a fan installed bringing the air into the machine WARNING Avoid small areas or areas near exhaust fans Electrical The machine when installed must be electrically grounded in accordance to local codes Check for proper power supply using a volt meter The HOT2 1100 HOT2 1500 and HOT3 1100 each require a 20 amp re ceptacle to comply to the UL 1776 Standard Placement Do not locate near any combustible material Keep all flammable material at least 20 feet away Allow enough space for servicing the machine Local code will require cert
27. dicates a lack of air and the air band should be moved to allow the air to flow through the burner Sharp eye burning white fumes indicate too much air flowing through the combustion chamber The air band should be moved to allow less air to flow through the burner Air Band Fuel Pump amp Air Adjustment Screw To adjust Start machine and turn burner ON Loosen two locking screws found in the air shutter openings re fer to illustration and close air shutter until black smoke appears from burner exhaust vent Note air band posi tion Next slowly open the air shutter until white smoke just starts to appear Turn air shutter halfway back to the black smoke position previously noted Tighten locking SCrews If the desired position cannot be obtained using only the air shutter lock the air shutter in as close a position as can be obtained then repeat the above procedure on the air band setting Initial Air Adjustments Allow sufficient air to obtain a clean burning flame by loosening the lock screws and moving the air shutter and if necessary the bulk air band Reduce the air supply until the flame tips appear slightly smoky then increase the air just enough to cause the flame tips to appear absolutely clean Removal of Soot and Heating Coil In the heating process fuel residue in the form of soot deposits may develop between the heating coil pipe and block air flow which will affect burner combust
28. do est parado sobre agua Siempre desconecte la m quina cuando le d servicio de mantenimiento Wa ey ADVERTENCIA Sostenga la pistola aspersora con ambas manos ya que con la alta presi n esta puede tener retroceso LANDA HOT 96 626 REV 2 04 EQUIPO DE LAVADO A PRESI N manvaL DEL OPERADOR 3 IDENTIFICACION DE COMPONENTES Adaptador de la Chimenea Inyector Detergente Manquito de Uni n de Descarga Conector R pido Manguera Conector de de Jard n Entrada Manguera de Suministro de Agua no se incluye Tanque de Combustible Interruptor de la Bomba y Suministro de del Quemador Electricidad de 20 Amperes Manguera ara Detergentes pr p H 0 S V CRA Sy Ge STAB di 0 Boquilla 0 ER Na E 4 Choaui Se Ta Boquilla para Detergente d lt gt Pd NN MAC RUE Var SS Conector C Mango de illa d m S s Tanque para Detergentes no se incluye Pistola e Aspersi n Manguera de Alta Presi n Conector Giratoria Boquilla de Vapor LANDA HOT 96 626 REV 2 04 32 EQUIPO DE LAVADO A PRESI N manuaL DEL OPERADOR 8 Sujete firmemente con ambas manos la varilla aspersora antes de encender la maquina de no seguir esta recomendaci n puede resultar en heridas por golpe de la misma 9 Nocoloque la m quina cerca de objetos inflamables si el motor esta cal
29. e lesi n es necesaria una supervisi n rigurosa al momento de utilizar una m quina cerca de ni os No permita que los ni os operen la m quina para lavado a presi n Es necesario supervisr la m quina durante su funcionamiento 44 ADVERTENCIA 19 Para prevenir una herida grave aseg rese que el conector r pido de la manguera de descarga este bien ajustado ntes de usar la m quina lavadora a presi n 20 No permita que cidos a flu dos abrasivos pasen a trav s de la bomba hidr ulica 21 No opere esta m quina estando fatigado o bajo la influencia del alcohol o drogas Mantenga el rea de operaci n lejos de las personas 22 El agua de entrada deber ser fr a 23 No se sobreestire o pare en soportes inestables mantenga el balance y pie firme en todo momento 24 Siga las instrucci nes de mantenimiento especificados en el manual 25 Siempre desconecte la m quina cuando realice reparaciones a la misma 26 Apague el quemador y libere de presi n la pistola y manguera de aspersi n Enfr e el serpent n a 100 F antes de apagar la m quina 27 Este equipo es para uso en interior PRECAUCION Aseg rese que el quemador est apagado y que el gatillo de la pistola de aspersi n este cerrado VERIFICACION ANTES DE OPERACION Aceite para bomba aceite SAE 30W sin detergente general e Suministro de agua fr a 5 gpm 5 8 20 psi e Manguera varilla boquilla tama o de boquilla seg n
30. eas bien ventiladas 5 Evite instalar unidades en reas peque as o cerca de ventiladoresde gases de es cape Losgasesde escape contienengas venenoso de mon xido de carbono la exposici n puede causar p rdida del conocimiento y causar la muerte Los gases de escape tambi n contienen detergentes en ciertas cantidades que se sabe causan c ncer defectos de nacimiento o da os al sistema reproductivo FT ADVERTENCIA Liquidos inflamables pueded crear gases que se encienden causando da os a la propiedad y heridas severas 6 Aparatos de encendido con petr leo deber n de ser instalados en lugares donde residuos de combustibles vapores o gases inflamables no est n normalmente presentes En modelos de encendido con petr leo utilice nicamente kerosene 1 o diesel No utilize gasolina solventes o alcohol El utilizarlo resultar en fuego y o explosi n ADVERTENCIA ADVERTENCIA Mantenga el chorro de agua la varilla y la manguera de alta presi n lejos del cableado el ctrico ya que puede ocurrir un choque fatal Lea la etiqueta de avertencia del cable el ctrico 7 Para proteger al operador de un choque el ctrico la m quina deber de estar conectada a tierra Es la responsabilidad del due o de conectar esta m quina a un recept culo a tierra aprobado por UL con el amperage y voltaje indicados No moje sobre o cerca de los componentes el ctricos no toque la m quina con las manos mojadas o cuan
31. ecomes plugged See Deliming Instructions for use of Landa Deliming Powder Deliming Coils Periodic flushing of coils or optional float tank is recom mended Step 1 Fill a container or float tank with 4 gallons of water then add 1 Ib of deliming powder Mix thoroughly Hemove wand assembly from spray gun and put spray gun into container or optional float tank Secure trigger on spray gun into the open posi tion Step3 Attach a short section 3 5 ft of garden hose to machine to siphon solution from an elevated con tainer Turn machine on allowing solution to be pumped through coils back into the container Solution should be allowed to circulate 2 4 hours Step 4 After circulating solution flush entire system with fresh water Reinstall high pressure nozzle into wand Step 2 LANDA HOT 96 626 REV 2 04 10 HOT SERIES PRESSURE WASHER OPERATOR S MANUAL Rupture Disk If pressure from pump or thermal expansion should ex ceed safe limits the rupture disk will burst allowing high pressure to be discharged through hose to ground When the disk ruptures it will need to be replaced Torque the replacement rupture disk to 35 foot pounds Fuel Use clean fuel oil that is not contaminated with water and debris Replace fuel filter and drain tank every 100 hours of operation Use No 1 or No 2 Heating Oil ASTM D306 only NEVER use gasoline in your burner tank Gasoline is more combustible than fuel oil and could re
32. ge nipple and se cure by pushing quick coupler collar forward 6 Securely attach the desired high pressure nozzle into wand coupler as described in steps 4 and 5 7 Connect the power cord into the proper electrical outlet then push in the GFCI reset button Refer to serial plate for information 8 Grip spray gun variable pressure wand securely Then turn the variable pressure control handle counter clockwise 9 Turn switch to pump position When a steady stream of water flows from the spray gun and wand the ma chine is ready for cold water cleaning by turning the variable pressure control handle clockwise to raise the pressure 10 For hot water washing turn the switch to the burner position The burner will light automatically NOTE The optional float tank siphons detergent through the pump when the detergent pick up tube is placed into a bucket of detergent and the detergent valve located on the control panel is opened To Stop 1 If using the detergent injector place detergent line in a bucket of water allowing detergent to be flushed from system see How To Use The Detergent Injec tor 2 Turn switch to pump position and continue spraying water allowing the water to cool 3 After water has cooled to less than 100 F turn switch to the off position 4 Turn water off Open the spray gun to relieve remain ing pressure 5 Protect from freezing REV 2 04 8 HOT SERIES PRESSURE WASHER operator s
33. however these do not imply a warranty that the product is merchantable or fit for a particular purpose or that the product will actually conform to the illustrations and specifications THE WARRANTY CONTAINED HEREIN IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR A PAR TICULAR PURPOSE LANDA does not authorize any other party including authorized LANDA Dealers to make any represen tation or promise on behalf of LANDA or to modify the terms conditions or limitations in any way It is the buyer s responsibility to ensure that the installation and use of LANDA products conforms to local codes While LANDA attempts to assure that its products meet national codes it cannot be responsible for how the customer chooses to use or install the product p Sur de ES LANDA HOT 96 626 REV 2 04 30 EQUIPO DE LAVADO A PRESI N wANUAL DEL OPERADOR INTRODUCCION Grac as por comprar un Lavadora a Presi n Landa Estas instrucciones y advertencias corresponden a los modelos HOT Landa Inc se reserva el derecho de hacer cualquier cambio en cualquier momento sin contraer ninguna obligaci n Responsabilidades del Dueno Usuario El dueno y o usuario debe estar al tanto de las instrucciones de operaci n y de las advertencias del fabricante antes de usar su lavadora a presi n Landa La informaci n de advertencia debe ser enfatizada y comprendida Si el operador no domina el ingl s el c
34. iente ADVERTENCIA Este equipo puede producir un fluido de alta persi n a chorro que puede penetrar la piel y sus tejidos causando graves heridas y posible amputacion 10 Las altas presiones desorrolladas por esta unidad causar n heridas personales o da o al equipo Use precauci n cuando est operando el equipo No dirija el chorro de descarga hacia la gente porque de lo contrario puede causarles heridas graves incluyendo la muerte 11 Nunca haga ajustes en la m quina mientras est operando ADVERTENCIA Un chorro de alta presi n puede ocasionar que trozos de pintura y otras particulas vuelen a alt s velocidades por el aire 12 Elementos de seguridad para la protecci n de los ojos y los pies deben ser usados con este equipo 13 Unidades con pistola de apagado no deben ser operadas con la pistola en la posici n apagada por largos per odos de tiempo pues sto puede causar da os a la bomba 14 El mejor seguro contra un accidente es la precauci n y el conocimiento de la m quina 15 Landa no se har responsable de ninguno de los cambios hechos a nuestras unidades est ndar o por ning n componente que no sea comprado directamente a Landa chorro de agua lejos de cables el ctricos para prevenir graves choques el ctricos 16 Lea las instrucciones de seguridad proporcionadas para el motor 17 Nunca opere la bomba en vacio o deje la pistola cerrada m s de 5 minutos 18 Para reducir el riesgo d
35. ion When soot has been detected on visual observation the soot on the coil must be washed off Follow these steps to remove the coil 1 Disconnect hose from pump to inlet side of the coil 2 Disconnect electrical connection to the thermostat 3 Remove quick coupler from inlet and discharge side of coil 4 Remove burner assembly from combustion cham ber 5 Remove the 3 3 8 bolts from each side of coil and tank assembly these bolts are used to fasten tank and handles to chassis 6 Disconnect 1 2 pipe nipples from inlet and discharge side of coil 7 Remove top tank wrap exposing insulation and coil and fold back insulation 8 Remove bolts that hold down coil to bottom wrap 9 Remove coll 10 Replace or repair any insulation found to be torn or broken Coil Reinstallation Reinstall new or cleaned coil by reversing Steps 9 through 1 above LANDA HOT 96 626 REV 2 04 12 HOT SERIES PRESSURE WASHER operator s MANUAL ELECTRICAL CONTROL PANEL LANDA HOT 96 626 REV 2 04 HOT SERIES PRESSURE WASHER operator s MANUAL 3 ELECTRICAL CONTROL PANEL PARTS LIST ITEM PART NO DESCRIPTION QTY ITEM PART NO DESCRIPTION QTY 1 8 Label Control Panel w Instr 1 18 6 05159 Connector Straight 1 2 2 0103 Grommet Rubber Nozzle 4 19 10 0201 14 Label Series Il 3 Pos Switch 1 3 Switch See pages 24 25 1 20 90 20012 Nut 5 16 Flange Whiz Loc 6 4 6 051595 Strain Relief LQ Tite 4 2A G K 21 10 0201177 Label
36. it will seize up the fuel pump Desoot coils monthly or use an additive if die sel is being used 9 If machine is operated with smoky or eye burning exhaust coils will soot up not letting water reach maximum operating temperature see Burner Ad justments 10 Never allow water to be sprayed on or near the mo tor the burner assembly or any electrical component 11 Periodically delime coils per instructions 12 Check to see that the motor is properly lubricated It is advisable periodically to visually inspect the burner Check air inlet to make sure it is not clogged or blocked Wipe off any oil spills and keep this equipment clean and dry The areas around the Landa washer should be kept clean and free of combustible materials gasoline and other flammable vapors and liquids The flow of combustion and ventilating air to the burner must not be blocked or obstructed in any manner MAINTENANCE AND SERVICE Unloader Valves Unloader valves trap pressure in the line when a spray gun is closed Unloader valves are preset and tested at the factory before shipping Occasional adjustment of the unloader may be necessary to maintain correct pressure Winterizing Procedure Damage due to freezing is not covered by warranty Ad here to the following cold weather procedures whenever the washer must be stored or operated outdoors under freezing conditions During winter months when temperatures drop below 32 F protecting
37. mo Para el servicio de la garant a de los componentes garantizados por otros fabricantes su Distribuidor Autorizado de LANDA le ayudar a obtener el servicio que necesite de estos fabricantes por medio de sus centros locales de servicio autorizado LIMITACI N DE LA RESPONSABILIDAD LANDA especificamente renuncia a la responsabilidad de todo da o y perjuicio especial incidental o consecuencial La responsabilidad de LANDA con respecto a todo reclamo de cualquier ndole no superar bajo circunstancia alguna el precio de compra del producto en cuesti n LANDA ha puesto todo su empefio para asegurarse de que las ilustraciones y especificaciones son las que corresponden no obstante estas no implican la garant a de comerciabilidad o de aptitud para un fin en particular o que el producto sea un fiel reflejo de las ilustraciones y especificaciones LA GARANT A CONTENIDA EN LA PRESENTE REEMPLAZA A CUALQUIER OTRA GARANT A SEA EXPRESA IMPL CITA INCLUSO TODA GARANT A IMPL CITADE APTITUD PARA UN FIN EN PARTICULAR LANDA no autoriza a terceros incluso a los Distribuidores Autorizados de LANDA a efectuar manifestaci n o promesa alguna en nombre de LANDA ni a modificar los t rminos condiciones o limitaciones en modo alguno Es responsabilidad del Comprador asegurarse de que la instalaci n y el uso de los productos LANDA se realice de acuerdo con los c digos locales Bien que Landa intenta asegurarse de que sus productos cumplan con los c digos
38. nacionales no se responsabiliza por el procedimiento de utilizaci n del producto ni por su instalaci n por parte del Comprador LANDA HOT 96 626 REV 2 04 LANDA WATER CLEANING SYSTEMS Form 896 626 Revised 2 04 Printed in U S A
39. ncender autom ticamente LANDA HOT 96 626 NOTA El modelo HOT3 30035D y el flotador opcional para m quinas con sif n para detergentes operan al colocar la toma de la manguera al contenedor con detergentes y abriendo la v lvula para entrada de detergentes localizada en el panel de control TECNICAS GENERALES DE LAVADO 1 Sostenga la boquilla de riego aproximadamente a 30 cm de la superficie a lavar Riegue a cierto ngulo a modo que golp e debajo de la sucidad o materia y la deprenda Cuando est lavando objetos grandes use un inyector detergente opcional para aplicar el detergente Empiece el lavado de abajo hacia arriba Se ahorrar detergente y obtendr resultados m s r pidos si permite que el detergente se asiente de 5 a 10 minutos Despu s de lavar enjuage de arriba hacia abajo Para la limpieza de mugre o materia pesada se recomienda un fuerte chorro de agua limpia antes de usar el agente limpiador ADVERTENCIA Con la maquina apagada abra la pistola para dejar salir la presi n antes de remover la manguera de descarga REV 2 04 34 EQUIPO DE LAVADO A PRESI N wANUAL DEL OPERADOR ad ay ADVERTENCIA Algunos detergentes pueden ser peligrosos si son inhalados o digeridos causando nausea severa desmayos O envenenamiento Elementos peligrosos pueden causar da o a la propiedad o heridas severas COMO USAR EL INYECTOR DETERGENTE La m quina puede actuar como sif n y mezclar los
40. nd flammable gases or vapors are not present 5 In oil burning models use only kerosene No 1 home heating fuel or diesel WARNING Do not use gasoline crankcase drainings or oil containing gasoline solvents or alcohol Do ing so will result in fire and or explosion 6 Risk of explosion Do not spray flammable liquids Operate only where open flame or torch is permitted 4h WARNING T kd A KEEPWATER SPRAY AWAY FROM ELECTRICAL WIRING WARNING Keep water spray wand and high pressure hose away from electrical wiring or fatal elec trical shock may result Read warning tag on electrical cord 7 To protect the operator from electrical shock the machine must be electrically grounded It is the responsibility of the owner to connect this machine to a UL grounded re ceptacle of proper voltage and amperage ratings Do not spray water on or near electrical components Do not touch machine with wet hands or while standing in water Always disconnect power before servicing WARNING Spray gun kicks back hold with both hands REV 2 04 HOT SERIES PRESSURE WASHER operator S MANUAL 5 COMPONENT IDENTIFICATION Detergent Injector Stackless Top Adapter Kit Optional 30 199 Discharge Nipple Collar Garden Hose Inlet gt Connector 9 Backflow Water Supply Plug Included 2 a On 230V Pump amp Burner 5 not included 1 PH Units
41. nyector Detergente Manguera Para Boquilla de Detergentes Descarga Manguera de Alta Pistola de Aspersi n Gatillo LANDA HOT 96 626 REV 2 04 EQUIPO DE LAVADO A PRESI N manual DEL OPERADOR 35 NILANDA taurosoetavaoarreson PRESSURE WASHERS QU CUBRE ESTA GARANT A LANDA INC garantiza al primer comprador que todos los equipos LANDA de lavado a presi n est n libres de defectos de materiales y de fabricaci n durante el uso normal de la unidad y durante el tiempo que se indica m s abajo Esta Garant a Limitada est sujeta a las exclusiones que se muestran a continuaci n Dicha garant a entra en vigencia a partir de la fecha de la compra del equipo y se aplica nicamente a los componentes originales Cualquier parte que se reemplace durante el per odo cubierto por esta garant a estar comprendida en el per odo de garant a restante para dicha parte GARANT A DE CINCO ANOS PARA LAS PARTES Y DE UN ANO PARA LA MANO DE OBRA Esta garant a cubre los componentes fabricados por Landa como por ejemplo bastidores manijas envoltura de bobinas tanques con flotador tanques para combustible cubiertas de correas y bobinas Los componentes internos relacionados con el aceite de las bombas marca bombas propietarias tienen una garant a de 5 afios GARANT A DE UN ANO M NIMO PARA LAS PARTES Y DE UN ANO PARA LA MANO DE OBRA El resto de los componentes sin incluir el desgaste normal de los art culos que se descri
42. omprador dueno deber leer y discutir con ste las instrucciones y las advertencias del fabricante en el idioma natal del operador asegur ndose de que ste entienda su contenido El dueno y o usuario debe estudiar y mantener las instrucciones del fabricante para futuras referencias Este manual debe ser considerado una parte permanente de la m quina y deber entregarse con la m quina en caso de que se venda Cuando ordene las partes por favor especifique el modelo y el n mero de serie INSTRUCCIONES DE SEQURIDAD IMPORTANTES 42 ADVERTENCIA ADVERTENCIA Cada vez que utilice esta m quina debe respetar las precauciones b sicas que incluyen las siguientes ADVERTENCIA Para reducir el riesgo de accidentes lea las instrucciones cuidadosamente antes de usar la unidad para operadores manual todo el cuidadosamente Al no seguir las instrucciones puede causar el malfuncion amiento de la unidad y provocar la muerte o causar serias heridas y o dafios en la propiedad 1 Lea 2 Sepa c mo detener la m quina y c mo eliminar presi n con rapidez Debe estar totalmente familiarizado con los controles 3 Permanezca alerta preste atenci n a lo que est haciendo 4 Todas las instalaciones deben cumplir con los c digos locales P ngase en contacto con un t cnico el ctrico plomero compa a de servicios p blicos o distribuidor de ventas para mayores detalles asfixia Use este producto solo en ar
43. placa de serie Filtro de agua intacto no restrictivo PROCEDIMIENTOS DE INSTALACION Este equipo es para uso en interior Este equipo debe ser guardado bajo techo cuando no esta en operacion 1 Conecte una manguera de jardin de 5 8 al conector de entrada El flujo m nimo debe ser de 5 gpm 2 Conecte una manguera de alta presi n a la boquilla de descarga usando una conexion r pida Asegure el conector ajust ndolo en su lugar tirando el collar del enganche trasero hacia atr s e insert dolo en la boquilla de descarga y empujando el collar despu s hacia adelante para asegurarlo en su lugar 3 Conecte la varilla a la pistola de riego usando cinta de tefl n en la rosca para prevenir fugas LANDA HOT 96 626 2 04 EQUIPO DE LAVADO A PRESI N manvaL DEL OPERADOR 33 Conecte el conector giratorio swivel en la manguera de descarga a la pistola de riego usando cinta de teflon en la rosca Remueva el tap n del aceite de encima de la bomba de la lavadora a presi n y reempl celo con el medidor de nivel dipstick proporcionado Verif que el nivel del aceite en el vidrio de observaci n que est al lado de la bomba El aceite debe ser visible hasta la mitad del vidrio de observaci n 30W no detergente Esta unidad cuando est instalada deber de estar el ctricamente conectada a tierra y en concordancia con las reglas locales de servicio p blico INSTRUCCIONES DE ENCENDIDO Y OPERACION 1
44. ploded 14 CHASSIS Assembly Parts EE 15 Combustion Assembly Exploded View pp 16 Combustion Assembly Parts 000 17 Pump Assembly Exploded View 3 30035D pp 18 HOT Manual Form 96 626 Revised 2 04 CONTENTS Pump Assembly Parts Lists UDS OD E 19 Pump Assembly Exploded View 2 1100 2 1500 3 1100 4 2000 A 20001 eee 20 Pump Assembly Parts List 2 1100 2 1500 3 1100 4 2000 4 3000 ee ececeeeeeeeeeeeeees 21 Hose Spray Gun amp Wand Assembly All Models 22 Downstream Injector Assembly All Models 23 Silent 24 free 8 25 27 Preventative Maintenance pp 28 O O o 28 VA EE EEE NE Oe 29 SPT NNN 30 35 Model Number Serial Number Date of Purchase The model and serial numbers will be found on a decal attached to the pressure washer You should record both serial number and date of purchase and keep in a safe place for future reference HOT Manual Form 896 626 Revised 2 04 4 HOT SERIES PRESSURE WASHER operator s MANUAL INTRODUCTION Thank you for purchasing a Landa Pressure Washer This manual covers the operation and maintenance of the HOT2 11021D HOT2 15021D HOT3 11021D HOT3 30035D HOT4 20021A HOT4 20021G HOT4 20021K and HOT4 30021N washers All information in
45. protector Reduce inlet water pressure Do not close trigger on spray gun for longer than five 5 minutes MACHINE SMOKES Weak fuel pump Check fuel pump pressure Replace pump if needed Fuel filter partially clogged Replace as needed Soot build up on coils Clean coils with soot remover Clean inside of coils using Landa s coil Lime build up in coils cleaner Improper burner nozzle 566 combustion assembly breakdown WATER TEMPERATURE Incoming water to machine warm or hot Lower incoming water temperature TOO HOT Fuel pump pressure too high Lower fuel pressure Fuel pump defective Replace fuel pump Detergent line sucking air Tighten all clamps Check detergent line for holes LANDA HOT 96 626 REV 2 04 HOT SERIES PRESSURE WASHER operator s MANUAL 27 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION BURNER LIGHT WILL Disconnected or short in electrical All wire contacts should be clean and tight No NOT LIGHT wiring breaks in wire Burner motor thermal protector tripped If tripped check voltage connections and extensions for cause Check fuel pump shaft rotation for binding causing motor to overheat Flex coupling slipping on fuel pump Replace if needed shaft or burner motor shaft ON OFF Switch defective Check continuity through burner switch Heavy sooting on coil and burner can Clean as required cause interruption of air flow and Clean and test according to diagram in Operators M
46. s or other particles to become airborne and fly at high speeds 11 Eye safety devices must be worn when using this equip ment 4 WARNING a USE PROTECTIVE EYEWEAR AND CLOTHINGWHEN OPERATING WARNING Risk of asphyxiation Use this product only in a well ventilated area 12 When the machine is working do not cover or place in a closed space where ventilation Is insuf ficient 4 WARNING RISK OF ASPHYXIATION USE ONLY INWELL VENTILATED AREA WARNING Risk of fire or explo sion Do not add fuel when machine is operating or still hot 13 The spray gun should not be op erated with the trigger in the off position for extended periods of time as this may cause damage to the pump Check to make sure burner shuts off when spray gun trigger is closed 14 Protect from freezing 15 To prevent a serious injury make certain quick cou pler on discharge hose has locked before using pres sure washer I RISK OF FIRE OR EXPLOSION REFUEL WITH CAUTION LANDA HOT 96 626 16 Do not allow acids caustic or abrasive fluids to pass through the pump 17 Inlet water supply must be cold and clean fresh water 18 Toreduce the risk of injury close supervision is nec essary when a product is used near children DO NOT ALLOW CHILDREN TO OPERATE the pres sure washer This machine must be attended dur ing operation 19 The best insurance against an accident is precau tion and knowledge of
47. scale build up rust corrosion or thermal expansion Damage to components from fluctuations in electrical or water supply Normal maintenance service including adjustments fuel system cleaning and clearing of obstructions Transportation to service center field labor charges or freight damage WHAT YOU MUST DO TO OBTAIN WARRANTY SERVICE While not required for warranty service we request that you register your LANDA pressure washer by returning the completed registration card In order to obtain warranty service on items warranted by LANDA you must return the product to your Autho rized LANDA Dealer freight prepaid with proof of purchase within the applicable warranty period If the product is permanently installed you must notify your Authorized LANDA Dealer of the defect Your Authorized LANDA Dealer will file a claim with Landa who must subsequently verify the defect In most cases the part must be returned to LANDA freight prepaid with the claim For warranty service on components warranted by other manufacturer s your Authorized LANDA Dealer can help you obtain warranty service through these manufacturers local authorized service centers LIMITATION OF LIABILITY LANDA S liability for special incidental or consequential damages is expressly disclaimed In no event shall LANDA S liability exceed the purchase price of the product in question LANDA makes every effort to ensure that all illustrations and specifica tions are correct
48. t Stackless Top Wrap 1 Exhaust Plate SS Stackless Top Wrap 1 Nut 10 32 Cage 4 Trim 1 16 Black 750B 2 3 25 ft Nipple 1 2 x 3 Galv Sch 80 1 Hose Barb 1 4 Barb x 1 4 ML Pipe 1 ITEM 26 EL 28 29 30 31 32 33 34 35 36 37 38 39 40 41 PART NO 90 4002 4 02100000 2 1089 2 9040 4 02100000 2 99031 2 3409 2 1019 6 05159 90 1019 90 20040 10 02025A 4 02100000 2 1108 4 02110000 LANDA HOT 96 626 REV 2 04 HOT SERIES PRESSURE WASHER operator s MANUAL 17 DESCRIPTION QTY Washer Flat SAE 3 8 2 Hose 1 4 x 6 Fuel Line 2 Hose Barb 90 1 4 Barb x 1 4 Pipe 1 Clamp Hose UNI 46 54 6 Hose 1 4 Fuel Line 12 Filter Diesel Fuel Disposable 1 Rupture Disk Assy 7000 PSI 1 Elbow 3 8 Female 1 Connector Straight Watertight 1 Bolt 3 8 x 1 1 2 2 Nut 3 8 Flange Whiz Loc 5 Label Hot Caliente W Arrows 1 Hose 1 4 Fuel Line 6 Hose Barb 1 2 Barb x 3 8 MPT Push On 1 Hose 1 2 Push On 1 2 ft Burner Assembly See Burner Spec s Page 24 A Not Shown 18 HOT SERIES PRESSURE WASHER operator s MANUAL PUMP ASSEMBLY HOT3 30035D 35 Le LANDA HOT 96 626 REV 2 04 PUMP ASSEMBLY HOT3 30035D PARTS LIST ITEM oo 4 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 PART NO 5 2273 5 1046 2 1062 2 1042 90 20231 2 1076 6 021730 6 021740 4 02090000 2 9040 2 1089
49. this manual is based on the latest product information available at the time of printing Landa Inc reserves the right to make changes at any time without incurring any obligation The HOT Series was designed for maximum use of 4 hours per day 5 days per week Owner User Responsibility The owner and or user must have an understanding of the manufacturer s operating instructions and warnings before using this Landa pressure washer Warning infor mation should be emphasized and understood If the op erator is not fluent in English the manufacturer s instruc tions and warnings shall be read to and discussed with the operator in the operators native language by the pur chaser owner making sure that the operator comprehends its contents Owner and or user must study and maintain for future reference the manufacturers instructions This manual should be considered a permanent part of the machine and should remain with it if machine is resold When ordering parts please specify model and serial number IMPORTANT SAFETY INFORMATION WARNING When using this machine basic precau tions should always be followed including the fol lowing CAUTION To reduce the risk of in jury read operating instructions carefully before using 1 Read the owner s manual thor oughly Failure to follow instruc tions could cause malfunction of the machine and result in death serious bodily injury and or property damage 2 Kno
50. ure nozzle at the end of the wand 8 For clean up place detergent pick up tube into con tainer of clear water and follow steps 5 and 6 to pre vent detergent deposits from damaging the injector Float Tank 1 Place detergent hose into detergent container and open detergent valve on control panel to desired setting 2 When you finish washing simply close the deter gent valve 3 For clean up place detergent hose into container of fresh clear water to prevent detergent deposits from damaging the pump and coil Discharge Nipple Quick Coupler GA 46 lt Detergent Injector High Pressure Hose 000 gt 200 0000707 NAF NNN WL Trigger REV 2 04 HOT SERIES PRESSURE WASHER oreraror s MANUAL 9 PREVENTATIVE MAINTENANCE 1 Check to see that water pump is properly lubricated 2 Follow Winterizing Procedures to prevent freeze dam age to pump and coils 3 Always neutralize and flush detergent from system after use 4 If water is known to be high in mineral content use a water softener on your water system or de scale as needed 5 Do not allow acidic caustic or abrasive fluids to be pumped through system 6 Always use high grade quality Landa cleaning prod ucts 7 Never run pump dry for extended periods of time 8 Useclean fuel kerosene No 1 fuel oil or diesel Re place fuel filter every 100 hours of operation Avoid water contaminated fuel as
51. w how to stop the machine and bleed pressures quickly Be thoroughly familiar with the controls 3 Stay alert watch what you are doing 4h CAUTION READ OPERATOR S THOROUGHLY PRIORTO USE LANDA HOT 96 626 4 Allinstallations must comply with local codes Con tact your electrician plumber utility company or the selling distributor for specific details To comply with the National Electrical Code NFPA 70 and provide additional protection from risk of shock this product is provided with a ground fault circuit interrupter GFCI built into the power cord plug 250V 30 amp or less 1 PH If replacement of the plug or cord is needed use only identical replacement parts DANGER Improper connection of the equipment grounding conduc tor can result in a risk of electro cution Check with a qualified elec trician or service personnel if you HAZARDOUS VOLTAGE CAN SHOCK BURN OR CAUSE DEATH GROUND SYSTEM BEFORE CONNECTINGTO POWER SUPPLY 4h WARNING Al RISK OF EXPLOSION DO NOT SPRAY FLAMMABLE LIQUIDS are in doubt as to whether the outlet is properly grounded Do not modify the plug provided with the product if it will not fit the outlet have a proper outlet in stalled by a qualified electrician WARNING Flammable liquids can create fumes which can ignite causing property damage or se vere injury WARNING This machine shall be installed only in locations where combustible dusts a
52. your machine against freezing is necessary otore the machine in a heated room If this is not pos sible then mix a 50 50 solution of antifreeze and water into a 5 gallon bucket Place a short section of garden hose into the bucket and connect it to the machine El evate the bucket and turn the pump on to siphon the antifreeze through the machine If compressed air is avail able screw an air fitting into the inlet connector By in jecting compressed air all water will be blown out of the system High Limit Hot Water Thermostat For safety each machine is equipped with a high limit control switch In the event the temperature of the water should exceed its operating temperature the high limit control will turn the burner off until the water cools Pumps Use only SAE 30 weight non detergent oil Change oil after first 50 hours of use Thereafter change oil every three months or at 500 hour intervals Oil level should be checked through use of dipstick found on top of pump Oil should be maintained at that level Cleaning of Coils In alkaline water areas lime deposits can accumulate rapidly inside the coil pipes This growth is increased by the extreme heat build up in the coil The best preventa tive for liming conditions is to use high quality cleaning detergents In areas where alkaline water is an extreme problem periodic use of Landa Deliming Powder Landa Part 9 028008 will remove lime and other deposits be fore coil b
Download Pdf Manuals
Related Search